diff options
Diffstat (limited to 'firmware/microblaze')
59 files changed, 5855 insertions, 260 deletions
diff --git a/firmware/microblaze/Makefile.am b/firmware/microblaze/Makefile.am index 6316b31a2..52fa649c2 100644 --- a/firmware/microblaze/Makefile.am +++ b/firmware/microblaze/Makefile.am @@ -23,4 +23,7 @@ EXTRA_DIST = \ u2_flash_tool SUBDIRS = \ - usrp2 + usrp2 \ + usrp2p \ + usrp2p/bootloader + diff --git a/firmware/microblaze/Makefile.common b/firmware/microblaze/Makefile.common index ceb6a553a..4e726edab 100644 --- a/firmware/microblaze/Makefile.common +++ b/firmware/microblaze/Makefile.common @@ -59,8 +59,13 @@ COMMON_LFLAGS = \ ######################################################################## # Common stuff for building top level microblaze images ######################################################################## +#we use COMMON_IHX_ARGS to relocate the reset and interrupt vectors to +#just below the start of code. upon creating the BIN, any leading padding +#is thrown out, so the .bin file is valid for uploading to USRP2P. this +#does not affect USRP2 because the USRP2 already starts at 0x0000, and +#because the relocate_args are not defined for USRP2's Makefile.am. .elf.bin: - $(MB_OBJCOPY) -O binary $< $@ + $(MB_OBJCOPY) -O binary $(RELOCATE_ARGS) $< $@ .elf.dump: $(MB_OBJDUMP) -DSC $< > $@ @@ -69,7 +74,7 @@ COMMON_LFLAGS = \ $(HEXDUMP) -v -e'1/1 "%.2X\n"' $< > $@ .elf.ihx: - $(MB_OBJCOPY) -O ihex $(COMMON_IHX_ARGS) $< $@ + $(MB_OBJCOPY) -O ihex $(RELOCATE_ARGS) $< $@ _generated_from_elf = \ $(noinst_PROGRAMS:.elf=.map) \ diff --git a/firmware/microblaze/apps/blinkenlights.c b/firmware/microblaze/apps/blinkenlights.c new file mode 100644 index 000000000..4cebe5c9d --- /dev/null +++ b/firmware/microblaze/apps/blinkenlights.c @@ -0,0 +1,26 @@ +/* -*- c++ -*- */ +/* + * Copyright 2010 Ettus Research LLC + * + */ + +#include "memory_map.h" +#include <nonstdio.h> + +int main(int argc, char *argv[]) { + + uint32_t c = 0; + uint8_t i = 0; + + while(1) { + //delay(5000000); + for(c=0;c<5000000;c++) asm("NOP"); + output_regs->leds = (i++ % 2) ? 0xFF : 0x00; //blink everything on that register + } + + return 0; +} + +//void delay(uint32_t t) { +// while(t-- != 0) asm("NOP"); +//} diff --git a/firmware/microblaze/apps/flash_test.c b/firmware/microblaze/apps/flash_test.c new file mode 100644 index 000000000..5b4569030 --- /dev/null +++ b/firmware/microblaze/apps/flash_test.c @@ -0,0 +1,67 @@ +/* -*- c++ -*- */ +/* + * Copyright 2010 Ettus Research LLC + * + */ + +#include <memory_map.h> +#include <hal_io.h> +#include <hal_uart.h> +#include <xilinx_s3_icap.h> +#include <nonstdio.h> +#include <spi_flash.h> +#include <spi.h> +#include <clocks.h> +#include <string.h> + +//just a test to write to SPI flash and retrieve the same values. +//uses the MOBFLEET SPI flash library + +void delay(uint32_t t) { + while(t-- != 0) asm("NOP"); +} + +int main(int argc, char *argv[]) { + uint16_t i, t; + uint8_t buf[260]; + const uint8_t testdata[] = {0xDE, 0xAD, 0xBE, 0xEF, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B, 0x0C}; + + hal_disable_ints(); // In case we got here via jmp 0x0 +// spi_init(); + hal_uart_init(); +// clocks_init(); //set up AD9510, enable FPGA clock @ 1x divisor + + puts("SPI Flash test\n"); + puts("Initializing SPI\n"); + + spif_init(); + delay(800000); + puts("Erasing sector 1\n"); + spi_flash_erase(0x00010000, 256); + delay(800000); + puts("Reading back data\n"); + spi_flash_read(0x00010000, 256, buf); + delay(800000); + + t=1; + for(i=4; i<250; i++) { + if(buf[i] != 0xFF) t=0; + } + + if(!t) puts("Data was not initialized to 0xFF. Unsuccessful erase or read\n"); + else puts("Data initialized to 0xFF, erase confirmed\n"); + + puts("Writing test buffer\n"); + spi_flash_program(0x00010000, 16, testdata); + //memset(buf, 0, 256); + + delay(800000); + puts("Wrote data, reading back\n"); + + spi_flash_read(0x00010000, 16, buf); + + if(memcmp(testdata, buf, 16)) puts("Data is not the same between read and write. Unsuccessful write or read\n"); + else puts("Successful write! Flash write correct\n"); + + return 0; +} diff --git a/firmware/microblaze/apps/hardware_testbed.c b/firmware/microblaze/apps/hardware_testbed.c new file mode 100644 index 000000000..e68e68ff7 --- /dev/null +++ b/firmware/microblaze/apps/hardware_testbed.c @@ -0,0 +1,47 @@ +/* -*- c++ -*- */ +/* + * Copyright 2010 Ettus Research LLC + * + */ + +#include <memory_map.h> +#include <nonstdio.h> +#include <hal_io.h> +#include <xilinx_s3_icap.h> +#include <spi_flash.h> +//#include <spi_flash_private.h> +#include <clocks.h> +#include <ihex.h> +#include <bootloader_utils.h> +#include <string.h> +#include <hal_uart.h> +#include <spi.h> + +//so this is just an evolving file used to set up and test different bits of hardware (EEPROM, clock chip, A/D, D/A, PHY) +void delay(uint32_t t) { + while(t-- != 0) asm("NOP"); +} + +int main(int argc, char *argv[]) { + + hal_disable_ints(); + hal_uart_init(); + spi_init(); + + puts("Hardware testbed. Init clocks..."); + + clocks_init(); + + //now, hopefully, we should be running at 100MHz instead of 50MHz, meaning our UART is twice as fast and we're talking at 230400. + + while(1) { + delay(500000); + puts("Eat at Joe's."); + } + + + + + + return 0; +} diff --git a/firmware/microblaze/apps/txrx_uhd.c b/firmware/microblaze/apps/txrx_uhd.c index 1dd6e80ac..482332f7c 100644 --- a/firmware/microblaze/apps/txrx_uhd.c +++ b/firmware/microblaze/apps/txrx_uhd.c @@ -42,9 +42,11 @@ #include <string.h> #include "clocks.h" #include "usrp2/fw_common.h" +#include <i2c_async.h> #include <i2c.h> #include <ethertype.h> #include <arp_cache.h> +#include "udp_fw_update.h" /* * Full duplex Tx and Rx between ethernet and DSP pipelines @@ -346,6 +348,28 @@ void handle_udp_ctrl_packet( send_udp_pkt(USRP2_UDP_CTRL_PORT, src, &ctrl_data_out, sizeof(ctrl_data_out)); break; + case USRP2_CTRL_ID_SO_LIKE_CAN_YOU_READ_THIS_UART_BRO:{ + //executes a readline()-style read, up to num_bytes long, up to and including newline + int num_bytes = ctrl_data_in->data.uart_args.bytes; + if(num_bytes > 20) num_bytes = 20; + num_bytes = fngets_timeout(ctrl_data_in->data.uart_args.dev, (char *) ctrl_data_out.data.uart_args.data, num_bytes); + ctrl_data_out.id = USRP2_CTRL_ID_I_HELLA_READ_THAT_UART_DUDE; + ctrl_data_out.data.uart_args.bytes = num_bytes; + break; + } + + case USRP2_CTRL_ID_HEY_WRITE_THIS_UART_FOR_ME_BRO:{ + int num_bytes = ctrl_data_in->data.uart_args.bytes; + if(num_bytes > 20) num_bytes = 20; + //before we write to the UART, we flush the receive buffer + //this assumes that we're interested in the reply + hal_uart_rx_flush(ctrl_data_in->data.uart_args.dev); + fnputstr(ctrl_data_in->data.uart_args.dev, (char *) ctrl_data_in->data.uart_args.data, num_bytes); + ctrl_data_out.id = USRP2_CTRL_ID_MAN_I_TOTALLY_WROTE_THAT_UART_DUDE; + ctrl_data_out.data.uart_args.bytes = num_bytes; + break; + } + default: ctrl_data_out.id = USRP2_CTRL_ID_HUH_WHAT; send_udp_pkt(USRP2_UDP_CTRL_PORT, src, &ctrl_data_out, sizeof(ctrl_data_out)); @@ -487,6 +511,7 @@ main(void) register_udp_listener(USRP2_UDP_CTRL_PORT, handle_udp_ctrl_packet); register_udp_listener(USRP2_UDP_DATA_PORT, handle_udp_data_packet); + register_udp_listener(USRP2_UDP_UPDATE_PORT, handle_udp_fw_update_packet); // initialize double buffering state machine for ethernet -> DSP Tx diff --git a/firmware/microblaze/apps/uart_flash_loader.c b/firmware/microblaze/apps/uart_flash_loader.c new file mode 100644 index 000000000..d67b84677 --- /dev/null +++ b/firmware/microblaze/apps/uart_flash_loader.c @@ -0,0 +1,169 @@ +/* -*- c++ -*- */ +/* + * Copyright 2010 Ettus Research LLC + * + */ + +//#include <stdio.h> +#include <stdlib.h> +#include <memory_map.h> +#include <nonstdio.h> +#include <hal_io.h> +#include <hal_uart.h> +#include <xilinx_s3_icap.h> +#include <spi_flash.h> +#include <spi_flash_private.h> +//#include <clocks.h> +#include <ihex.h> +#include <bootloader_utils.h> + +//uses UART to load files to Flash in Intel HEX 16-bit format. +//this is one example of a "safe" firmware image to be loaded by a bootloader into main RAM. +//this CANNOT write to main RAM, since it is resident there. + +//Sector 0-31: Safe FPGA bootloader image +//Sector 32-63: Production bootloader image +//Sector 64: Production firmware image +//Sector 127: Safe firmware image + + +void uart_flash_loader(void) { + + char buf[256]; //input data buffer + uint8_t ihx[32]; //ihex data buffer + uint32_t slot_offset = PROD_FW_IMAGE_LOCATION_ADDR; //initial slot offset to program to. + uint32_t extended_addr = 0x00000000; //extended Intel hex segment address + + size_t sector_size = spi_flash_log2_sector_size(); + ihex_record_t ihex_record; + ihex_record.data = ihx; + int i; + + + //not gonna win a turing prize for my C text parsing + while(1) { + gets(buf); + if(!strncmp(buf, "!SECTORSIZE", 7)) { //return the sector size in log format + putstr("OK "); + puthex8((uint32_t) sector_size); //err, this should probably be decimal for human readability. we do have itoa now... + putstr("\n"); + } + else if(!strncmp(buf, "!SETADDR", 7)) { //set start address for programming + slot_offset = atol(&buf[8]); + puts("OK"); +// puthex32(slot_offset); +// putstr("\n"); + } + else if(!strncmp(buf, "!ERASE", 6)) { //erase a sector + uint32_t sector = atol(&buf[6]); + uint32_t size = 2 << (sector_size-1); + uint32_t addr = sector << sector_size; + + spi_flash_erase(addr, size); //we DO NOT implement write protection here. it is up to the HOST PROGRAM to not issue an ERASE unless it means it. + //unfortunately the Flash cannot write-protect the segments that really matter, so we only use global write-protect + //as a means of avoiding accidental writes from runaway code / garbage on the SPI bus. + puts("OK"); + } +//can't exactly run firmware if you're already executing out of main RAM +/* else if(!strncmp(buf, "!RUNSFW", 7)) { + if(is_valid_fw_image(SAFE_FW_IMAGE_LOCATION_ADDR)) { + puts("OK"); + spi_flash_read(SAFE_FW_IMAGE_LOCATION_ADDR, FW_IMAGE_SIZE_BYTES, (void *)RAM_BASE); + start_program(RAM_BASE); + } else { + puts("NOK"); + } + } + else if(!strncmp(buf, "!RUNPFW", 7)) { + if(is_valid_fw_image(PROD_FW_IMAGE_LOCATION_ADDR)) { + puts("OK"); + spi_flash_read(PROD_FW_IMAGE_LOCATION_ADDR, FW_IMAGE_SIZE_BYTES-1, (void *)RAM_BASE); + start_program(RAM_BASE); + } else { + puts("NOK"); + } + } +*/ + else if(!strncmp(buf, "!RUNPFPGA", 8)) { + if(is_valid_fpga_image(PROD_FPGA_IMAGE_LOCATION_ADDR)) { + puts("OK"); + //icap_reload_fpga(PROD_FPGA_IMAGE_LOCATION_ADDR); + } else { + puts("NOK"); + } + } + else if(!strncmp(buf, "!RUNSFPGA", 8)) { + if(is_valid_fpga_image(SAFE_FPGA_IMAGE_LOCATION_ADDR)) { + puts("OK"); + //icap_reload_fpga(SAFE_FPGA_IMAGE_LOCATION_ADDR); + } else { + puts("NOK"); + } + } + else if(!strncmp(buf, "!READ", 5)) { + uint32_t addr = atol(&buf[5]); + spi_flash_read(addr, 16, ihx); + for(i=0; i < 16; i++) { + puthex8(ihx[i]); + } + putstr("\n"); + } + + else if(!ihex_parse(buf, &ihex_record)) { //last, try to see if the input was a valid IHEX line + switch (ihex_record.type) { + case 0: + spi_flash_program(ihex_record.addr + slot_offset + extended_addr, ihex_record.length, ihex_record.data); + puts("OK"); + break; + case 1: + //here we would expect a CRC checking or something else to take place. for now we do nothing. + //well, we set the extended segment addr back to 0 + extended_addr = 0; + puts("DONE"); + break; + case 4: + //set the upper 16 bits of the address + extended_addr = ((ihex_record.data[0] << 8) + ihex_record.data[1]) << 16; + puts("OK"); + break; + default: + puts("NOK"); + } + } + else puts("NOK"); + } //while(1) +} + +void delay(uint32_t t) { + while(t-- != 0) asm("NOP"); +} + +int main(int argc, char *argv[]) { + uint8_t buf[32]; + int i = 0; + + hal_disable_ints(); // In case we got here via jmp 0x0 + +// delay(10000000); + + //before anything else you might want to blinkenlights just to indicate code startup to the user. + + hal_uart_init(); + spif_init(); +// i2c_init(); //for EEPROM + puts("USRP2+ UART firmware loader"); + +// puts("Debug: loading production image, 10 bytes."); + +// spi_flash_read(PROD_FW_IMAGE_LOCATION_ADDR, 10, buf); +// for(i=0; i < 10; i++) { +// puthex8(buf[i]); +// } + + uart_flash_loader(); + + //shouldn't get here. should reboot. + puts("shit happened.\n"); + + return 0; +} diff --git a/firmware/microblaze/bin/bin_to_mif.py b/firmware/microblaze/bin/bin_to_mif.py new file mode 100755 index 000000000..cefce4e92 --- /dev/null +++ b/firmware/microblaze/bin/bin_to_mif.py @@ -0,0 +1,29 @@ +#!/usr/bin/env python + +import struct +import sys + +hextab = ('0000', '0001', '0010', '0011', + '0100', '0101', '0110', '0111', + '1000', '1001', '1010', '1011', + '1100', '1101', '1110', '1111') + +def w_to_binary_ascii(w): + return ''.join([hextab[(w >> 4*i) & 0xf] for i in range(7,-1,-1)]) + +def bin_to_mif(bin_input_file, mif_output_file): + ifile = open(bin_input_file, 'rb') + ofile = open(mif_output_file, 'w') + idata = ifile.read() + fmt = ">%dI" % ((len(idata) / 4),) + words = struct.unpack(fmt, idata) + for w in words: + ofile.write(w_to_binary_ascii(w)) + ofile.write('\n') + +if __name__ == '__main__': + if len(sys.argv) != 3: + sys.stderr.write("usage: bin_to_mif bin_input_file mif_output_file\n") + raise SystemExit, 1 + + bin_to_mif(sys.argv[1], sys.argv[2]) diff --git a/firmware/microblaze/bin/bin_to_ram_macro_init.py b/firmware/microblaze/bin/bin_to_ram_macro_init.py new file mode 100755 index 000000000..65cf2dbdf --- /dev/null +++ b/firmware/microblaze/bin/bin_to_ram_macro_init.py @@ -0,0 +1,48 @@ +#!/usr/bin/env python + +import struct +import sys + +def do_8_words(ofile, which_ram, row, words): + ofile.write("defparam bootram.RAM%d.INIT_%02X=256'h" % (which_ram, row)) + ofile.write("%08x_%08x_%08x_%08x_%08x_%08x_%08x_%08x;\n" % ( + words[7], words[6], words[5], words[4], words[3], words[2], words[1], words[0])) + +def bin_to_ram_macro_init(bin_input_file, ram_init_output_file): + ifile = open(bin_input_file, 'rb') + ofile = open(ram_init_output_file, 'w') + idata = ifile.read() + fmt = ">%dI" % ((len(idata) / 4),) + words = struct.unpack(fmt, idata) + + # pad to a multiple of 8 words + r = len(words) % 8 + if r != 0: + words += (8 - r) * (0,) + + if len(words) > 2048: + sys.stderr.write("bin_to_macro_init: error: input file %s is > 8KiB\n" % (bin_input_file,)) + sys.exit(1) + + # first 2KB + for i in range(0, min(512, len(words)), 8): + do_8_words(ofile, 0, i/8, words[i:i+8]) + + # second 2KB + for i in range(512, min(1024, len(words)), 8): + do_8_words(ofile, 1, (i/8) % 64, words[i:i+8]) + + # third 2KB + for i in range(1024, min(1536, len(words)), 8): + do_8_words(ofile, 2, (i/8) % 64, words[i:i+8]) + + # last 2KB + for i in range(1536, len(words), 8): + do_8_words(ofile, 3, (i/8) % 64, words[i:i+8]) + +if __name__ == '__main__': + if len(sys.argv) != 3: + sys.stderr.write("usage: bin_to_ram_macro_init bin_input_file ram_init_output_file\n") + sys.exit(1) + + bin_to_ram_macro_init(sys.argv[1], sys.argv[2]) diff --git a/firmware/microblaze/bin/elf_to_sbf b/firmware/microblaze/bin/elf_to_sbf new file mode 100755 index 000000000..d1be10c0d --- /dev/null +++ b/firmware/microblaze/bin/elf_to_sbf @@ -0,0 +1,142 @@ +#!/usr/bin/env python +# +# Copyright 2009 Free Software Foundation, Inc. +# +# This program is free software: you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation, either version 3 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. +# + +import sys +import struct +from optparse import OptionParser +from pprint import pprint + +import sbf + +# see /usr/include/elf.h for the various magic values + + +_ehdr_fmt = ">16sHH5I6H" +_ehdr_fmt_size = struct.calcsize(_ehdr_fmt) +_phdr_fmt = ">8I" +_phdr_fmt_size = struct.calcsize(_phdr_fmt) + +class elf32_ehdr(object): + def __init__(self, s): + (self.ident, self.type, self.machine, self.version, self.entry, + self.phoff, self.shoff, self.flags, self.ehsize, + self.phentsize, self.phnum, self.shentsize, self.shnum, + self.shstrndx) = struct.unpack(_ehdr_fmt, s) + +class elf32_phdr(object): + def __init__(self, s): + (self.type, self.offset, self.vaddr, self.paddr, + self.filesz, self.memsz, + self.flags, self.align) = struct.unpack(_phdr_fmt, s) + + def __repr__(self): + return "<elf32_phdr %s offset=%d paddr=0x%x, filesz=%d>" % ( + p_type_str(self.type), self.offset, self.paddr, self.filesz) + + +def p_type_str(t): + if t <= 8: + return ('NULL', 'LOAD', 'DYNAMIC', 'INTERP', 'NOTE', 'SHLIB', 'PHDR', 'TLS', 'NUM')[t] + return "0x%x" % (t,) + + + +def _get_ehdr(f): + if len(f) < _ehdr_fmt_size: + return False + ehdr = elf32_ehdr(f[0:_ehdr_fmt_size]) + return ehdr + + +def elf32_big_endian_exec_p(f): + ehdr = _get_ehdr(f) + if not ehdr: + return False + + #pprint(ehdr, sys.stderr) + e_ident = ehdr.ident + if not e_ident.startswith('\177ELF'): + return False + if (ord(e_ident[4]) != 1 # EI_CLASS == CLASS32 + or ord(e_ident[5]) != 2 # EI_DATA == DATA2MSB + or ord(e_ident[6]) != 1 # EI_VERSION == EV_CURRENT + ): + return False + + if ehdr.type != 2: # e_type == ET_EXEC + return False + + return True + + + +# return (entry, (phdr, ...)) + +def get_elf32_prog_headers(f): + ehdr = _get_ehdr(f) + entry = ehdr.entry + phoff = ehdr.phoff + phentsize = ehdr.phentsize + phnum = ehdr.phnum + + def extract(i): + start = phoff + i * phentsize + end = start + phentsize + return f[start:end] + + return (entry, [elf32_phdr(extract(i)) for i in range(phnum)]) + + +def main(): + usage = "%prog: [options] elf_file" + parser = OptionParser() + parser.add_option("-o", "--output", default=None, + help="specify output filename [default=stdout]") + (options, args) = parser.parse_args() + if len(args) != 1: + parser.print_help() + sys.exit(1) + + elf_file = open(args[0], 'rb') + + elf_contents = elf_file.read() + if not elf32_big_endian_exec_p(elf_contents): + sys.stderr.write("%s: not a big-endian 32-bit ELF executable\n" % (args[0],)) + sys.exit(1) + + if options.output is None: + sbf_file = sys.stdout + else: + sbf_file = open(options.output, 'wb') + + (entry, phdrs) = get_elf32_prog_headers(elf_contents) + #pprint(phdrs, sys.stderr) + + def phdr_to_sec_desc(phdr): + target_addr = phdr.paddr + data = elf_contents[phdr.offset:phdr.offset+phdr.filesz] + #print >>sys.stderr, "pdhr_to_sec_desc:", (target_addr, data) + return sbf.sec_desc(target_addr, data) + + sections = map(phdr_to_sec_desc, phdrs) + # pprint(sections, sys.stderr) + sbf.write_sbf(sbf_file, sbf.header(entry, sections)) + + +if __name__ == '__main__': + main() diff --git a/firmware/microblaze/bin/sbf.py b/firmware/microblaze/bin/sbf.py new file mode 100644 index 000000000..8e2c868a5 --- /dev/null +++ b/firmware/microblaze/bin/sbf.py @@ -0,0 +1,134 @@ +# +# Copyright 2009 Free Software Foundation, Inc. +# +# This program is free software: you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation, either version 3 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. +# + +_SBF_MAGIC = 'SBF!' +_SBF_DONT_EXECUTE = 0x1 +_SBF_MAX_SECTIONS = 14 +_SBF_HEADER_LEN = 128 + +import struct +import sys +from pprint import pprint + +def dump_data(f, offset, data): + L = len(data) // 4 + for i in range(L): + f.write('%08x: %08x\n' % (offset + 4 * i, struct.unpack('>I', data[4*i:4*(i+1)])[0])) + remainder = len(data) - L * 4 + if remainder != 0: + f.write('%08x: ' % (offset + L*4,)) + i = 0 + while i < remainder: + f.write('%02x' % ((ord(data[L*4 + i]),))) + i += 1 + f.write('\n') + + + +class sec_desc(object): + def __init__(self, target_addr, data): + self.target_addr = target_addr + self.data = data + + def __repr__(self): + #print >>sys.stderr, "target_addr:", self.target_addr + #print >>sys.stderr, "data:", self.data + return "<sec_desc target_addr=0x%x len=%d>" % ( + self.target_addr, len(self.data)) + + +class header(object): + def __init__(self, entry, sections): + self.entry = entry + self.section = sections + + def dump(self, f): + if self.entry == _SBF_DONT_EXECUTE: + f.write("Entry: DONT_EXECUTE\n") + else: + f.write("Entry: 0x%x\n" % (self.entry,)) + for i in range(len(self.section)): + s = self.section[i] + f.write("Section[%d]: target_addr = 0x%x length = %d\n" % (i, + s.target_addr, + len(s.data))) + dump_data(f, s.target_addr, s.data) + + # + # Returns an iterator. Each yield returns (target_addr, data) + # + def iterator(self, max_piece=512): + for s in self.section: + offset = 0 + L = len(s.data) + while offset < L: + n = min(max_piece, L - offset) + yield (s.target_addr + offset, + s.data[offset:offset+n]) + offset += n + + + +def read_sbf(input_file): + """Parse an SBF file""" + + f = input_file.read(_SBF_HEADER_LEN) + #if len(f) < _SBF_HEADER_LEN or not f.startswith(_SBF_MAGIC): + #raise ValueError, '%s: not an SBF file' % (input_file.name,) + + def extract(i): + start = 16+8*i + stop = start+8 + return struct.unpack('>2I', f[start:stop]) + + def get_data(ss): + L = ss[1] + s = input_file.read(L) + #if len(s) != L: + #raise ValueError, '%s: file is too short' % (input_file.name(),) + return s + + (magic, entry, nsections, reserved) = struct.unpack('>4s3I', f[0:16]) + assert nsections <= _SBF_MAX_SECTIONS + descs = [extract(i) for i in range(nsections)] + #pprint(descs, sys.stderr) + data = map(get_data, descs) + secs = map(lambda ss, data: sec_desc(ss[0], data), descs, data) + return header(entry, secs) + + +def write_sbf(output_file, sbf_header): + assert(len(sbf_header.section) <= _SBF_MAX_SECTIONS) + sbf_header.nsections = len(sbf_header.section) + f = output_file + + # write the file header + f.write(struct.pack('>4s3I', _SBF_MAGIC, sbf_header.entry, sbf_header.nsections, 0)) + + # write the section headers + for i in range(sbf_header.nsections): + f.write(struct.pack('>2I', + sbf_header.section[i].target_addr, + len(sbf_header.section[i].data))) + for i in range(_SBF_MAX_SECTIONS - sbf_header.nsections): + f.write(struct.pack('>2I', 0, 0)) + + # write the section data + for i in range(sbf_header.nsections): + f.write(sbf_header.section[i].data) + + return True diff --git a/firmware/microblaze/bin/serial_loader b/firmware/microblaze/bin/serial_loader new file mode 100755 index 000000000..9bd5aada7 --- /dev/null +++ b/firmware/microblaze/bin/serial_loader @@ -0,0 +1,363 @@ +#!/usr/bin/env python +# +# Copyright 2009 Free Software Foundation, Inc. +# +# This program is free software: you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation, either version 3 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. +# + +import termios +import tty +import os +import sys +import threading +import Queue +from optparse import OptionParser +import time + +import sbf + +GDB_ESCAPE = chr(0x7d) + +# Indexes for termios list. +IFLAG = 0 +OFLAG = 1 +CFLAG = 2 +LFLAG = 3 +ISPEED = 4 +OSPEED = 5 +CC = 6 + +class terminal(object): + def __init__(self, device, speed_bits): + fd = os.open(device, os.O_RDWR) + if not os.isatty(fd): + raise ValueError(device + " is not a tty") + + self.read_file = os.fdopen(fd, "rb", 0) + self.write_file = os.fdopen(os.dup(fd), "wb", 0) + self.old_attrs = termios.tcgetattr(self.write_file.fileno()) + #print "old_attrs: ", self.old_attrs + attrs = list(self.old_attrs) # copy of attributes + attrs[ISPEED] = speed_bits # set input and output speed + attrs[OSPEED] = speed_bits + termios.tcsetattr(self.write_file.fileno(), termios.TCSAFLUSH, attrs) + tty.setraw(self.write_file.fileno()) # enable raw mode + attrs = termios.tcgetattr(self.write_file.fileno()) + attrs[CC][termios.VMIN] = 1 # minimim of 1 char + attrs[CC][termios.VTIME] = 1 # wait no longer than 1/10 + termios.tcsetattr(self.write_file.fileno(), termios.TCSAFLUSH, attrs) + + def __del__(self): + termios.tcsetattr(self.write_file.fileno(), termios.TCSAFLUSH, self.old_attrs) + self.read_file.close() + self.write_file.close() + + def read(self, n): + """Read at most n bytes from tty""" + return self.read_file.read(n) + + def write(self, str): + """Write str to tty.""" + return self.write_file.write(str) + + +def hexnibble(i): + return "0123456789abcdef"[i & 0xf] + +def build_pkt(payload): + s = ['$'] + checksum = 0 + + for p in payload: + if p in ('$', '#', GDB_ESCAPE): + s.append(GDB_ESCAPE) + s.append(p) + checksum += ord(p) + + checksum &= 0xff + s.append('#') + s.append(hexnibble(checksum >> 4)) + s.append(hexnibble(checksum)) + + return ''.join(s) + + +def build_memory_read_pkt(addr, len): + return build_pkt(('m%x,%x' % (addr, len))) + +def build_memory_write_hex_pkt(addr, s): + hexdata = ''.join(["%02x" % (ord(c),) for c in s]) + return build_pkt(('M%x,%x:' % (addr, len(s))) + hexdata) + +def build_memory_write_pkt(addr, s): + return build_pkt(('X%x,%x:' % (addr, len(s))) + s) + +def build_goto_pkt(addr): + return build_pkt(('c%x' % (addr,))) + + +def get_packet(f): + """Return a valid packet, or None on EOF or timeout""" + LOOKING_FOR_DOLLAR = 0 + LOOKING_FOR_HASH = 1 + CSUM1 = 2 + CSUM2 = 3 + + fd = f.fileno() + + state = LOOKING_FOR_DOLLAR + buf = [] + + while True: + ch = os.read(fd, 1) + sys.stdout.write(ch) + if len(ch) == 0: + print("Returning None") + return(None) + + if state == LOOKING_FOR_DOLLAR: + if ch == '$': + buf = [] + state = LOOKING_FOR_HASH + elif ch == '#': + state = LOOKING_FOR_DOLLAR + + elif state == LOOKING_FOR_HASH: + if ch == '$': + state = LOOKING_FOR_DOLLAR + elif ch == '#': + state = CSUM1 + else: + if ch == GDB_ESCAPE: + ch = getc() + buf.append(ch) + + elif state == CSUM1: + chksum1 = ch + state = CSUM2 + + elif state == CSUM2: + chksum2 = ch + r = ''.join(buf) + if chksum1 == '.' and chksum2 == '.': + return r + + expected_checksum = int(chksum1 + chksum2, 16) + checksum = 0 + for c in buf: + checksum += ord(c) + + checksum &= 0xff + if checksum == expected_checksum: + return r + + state = LOOKING_FOR_DOLLAR + + else: + raise ValueError( "Invalid state") + + +class packet_reader_thread(threading.Thread): + def __init__(self, tty_in, q): + threading.Thread.__init__(self) + self.setDaemon(1) + self.tty_in = tty_in + self.q = q + self._keep_running = True + self.start() + + def run(self): + while self._keep_running == True: + p = get_packet(self.tty_in) + if p is not None: + self.q.put(('pkt', p)) + + +def _make_tr_table(): + table = [] + for c in range(256): + if c < ord(' ') or c > ord('~'): + table.append('.') + else: + table.append(chr(c)) + return ''.join(table) + + +class controller(object): + def __init__(self, tty): + self.tty = tty + self.q = Queue.Queue(0) + self.timers = {} + self.next_tid = 1 + self.current_tid = 0 + self.ntimeouts = 0 + self.packet_reader = packet_reader_thread(tty.read_file, self.q) + self.state = None + self.debug = False + self.tt = _make_tr_table() + + self.done = False + self.addr = None + self.bits = None + + def shutdown(self): + self.packet_reader._keep_running = False + + def start_timeout(self, timeout_in_secs): + def callback(tid): + if self.timers.has_key(tid): + del self.timers[tid] + self.q.put(('timeout', tid)) + self.next_tid += 1 + tid = self.next_tid + timer = threading.Timer(timeout_in_secs, callback, (tid,)) + self.timers[tid] = timer + timer.start() + return tid + + def cancel_timeout(self, tid): + if self.timers.has_key(tid): + self.timers[tid].cancel() + del self.timers[tid] + + def send_packet(self, pkt): + if self.debug: + if len(pkt) > 64: + s = pkt[0:64] + '...' + else: + s = pkt + sys.stdout.write('-> ' + s.translate(self.tt) + '\n') + self.tty.write(pkt); + + def send_packet_start_timeout(self, pkt, secs): + self.send_packet(pkt) + self.current_tid = self.start_timeout(secs) + + def upload_code(self, sbf): + MAX_PIECE = 512 # biggest piece to send + MWRITE_TIMEOUT = 0.1 + + IDLE = 0 + WAIT_FOR_ACK = 1 + UPLOAD_DONE = 2 + DONE = 3 + FAILED = 4 + + self.done = False + it = sbf.iterator(MAX_PIECE) + entry_addr = sbf.entry + + def get_next_bits(): + try: + (self.addr, self.bits) = it.next() + except StopIteration: + self.done = True + + def is_done(): + return self.done + + def send_piece(): + pkt = build_memory_write_pkt(self.addr, self.bits) + #pkt = build_memory_write_hex_pkt(self.addr, self.bits) + self.send_packet_start_timeout(pkt, MWRITE_TIMEOUT) + state = WAIT_FOR_ACK + + def advance(): + get_next_bits() + if is_done(): + self.state = DONE + self.send_packet(build_goto_pkt(entry_addr)) + + else: + self.ntimeouts = 0 + send_piece() + + get_next_bits() + if is_done(): # empty file + return True + + send_piece() # initial transition + + while 1: + (event, value) = self.q.get() + + if event == 'timeout' and value == self.current_tid: + self.ntimeouts += 1 + if self.ntimeouts >= 5: + return False # say we failed + send_piece() # resend + + + elif event == 'pkt': + if value == 'OK': + self.cancel_timeout(self.current_tid) + advance() + if self.state == DONE: + return True + else: + print("Error returned from firmware: " + value) + return False + + else: + print("Unknown event:", (event, value)) + +def main(): + usage="%prog: [options] filename" + parser = OptionParser(usage=usage) + parser.add_option("-t", "--tty", type="string", default="/dev/ttyS0", + help="select serial port [default=%default]") + + (options, args) = parser.parse_args() + if len(args) != 1: + parser.print_help() + raise SystemExit(1) + + + filename = args[0] + f = open(filename, "rb") + try: + # Try to open the file as an SBF file + sbf_header = sbf.read_sbf(f) + except: + # If that fails, build an SBF from the binary, assuming default + # load address and entry point + f.seek(0) + t = f.read() + if t.startswith('\177ELF'): + sys.stderr.write("Can't load an ELF file. Please use an SBF file instead.\n") + raise SystemExit( 1) + sbf_header = sbf.header(0x8000, [sbf.sec_desc(0x8000, t)]) + + + tty = terminal(options.tty, termios.B115200) + ctrl = controller(tty) + ok = ctrl.upload_code(sbf_header) + + if ok: + print("OK") + try: + raw_input("Press Enter to exit: ") + except KeyboardInterrupt: + pass + ctrl.shutdown() + time.sleep(0.2) + + else: + print("Upload failed") + ctrl.shutdown() + + + +if __name__ == "__main__": + main() diff --git a/firmware/microblaze/bin/uart_ihex_flash_loader.py b/firmware/microblaze/bin/uart_ihex_flash_loader.py new file mode 100755 index 000000000..5a3300f34 --- /dev/null +++ b/firmware/microblaze/bin/uart_ihex_flash_loader.py @@ -0,0 +1,138 @@ +#!/usr/bin/python + +import serial +from optparse import OptionParser +import os, sys + +#TODO: pull everything but parser out of main() and put it in a separate function we can call from another script. lets us automate loading RAM+FLASH to produce a fully-loaded image. +#TODO: make it fail gracefully -- if it gets a NOK or times out, do at least one retry. +#TODO: put hooks in (eventually) to allow verifying a firmware image so the user can more safely update the "safe" image +#TODO: how about a progress indicator? FPGA images take FOREVER. you can use wc -l to get the number of lines, or do it with file i/o. + +def main(): + usage="%prog: [options] filename" + parser = OptionParser(usage=usage) + parser.add_option("-t", "--tty", type="string", default="/dev/ttyUSB0", + help="select serial port [default=%default]") + parser.add_option("-b", "--baudrate", type=int, default=115200, + help="set baudrate [default=%default]") + parser.add_option("-F", "--write-safe-firmware", action="store_const", const=1, dest="image", + help="write to safe firmware image") + parser.add_option("-f", "--write-production-firmware", action="store_const", const=2, dest="image", + help="write to production firmware image") + parser.add_option("-P", "--write-safe-fpga", action="store_const", const=3, dest="image", + help="write to safe FPGA image") + parser.add_option("-p", "--write-production-fpga", action="store_const", const=4, dest="image", + help="write to production FPGA image") + + (options, args) = parser.parse_args() + + if(options.image is None): + print("At least one of -f, -F, -p, -P must be specified.\n") + parser.print_help() + raise SystemExit(1) + + if len(args) != 1: + parser.print_help() + raise SystemExit(1) + + if(options.image == 3): + print "Are you *really* sure you want to write to the failsafe FPGA image? If you mess this up your USRP2+ will become a brick. Press 'y' to continue, any other key to abort." + if(raw_input().rstrip() is not "y"): + print "Good choice." + raise SystemExit(0) + + elif(options.image == 1): + print "Are you *really* sure you want to write to the failsafe firmware image? If you mess this up your USRP2+ will only be able to be reprogrammed via the UART RAM loader.\nPress 'y' to continue, any other key to abort." + if(raw_input().rstrip() is not "y"): + print "Good choice." + raise SystemExit(0) + + filename = args[0] + f = open(filename, "r") + + #now we start doing things... + if(os.path.exists(options.tty) is False): + sys.stderr.write("No serial port found at %s\n" % options.tty) + raise SystemExit(1) + + try: + ser = serial.Serial(port=options.tty, timeout=1, baudrate=options.baudrate, bytesize=8, parity=serial.PARITY_NONE, stopbits=1, rtscts=0, xonxoff=0) + except serial.SerialException: + sys.stderr.write("Unable to open serial port\n") + raise SystemExit(1) + + ser.open() + +#test to see if a valid USRP2+ in flash load mode is connected + ser.write("garbage\n") + ser.readline() + ser.write("!SECTORSIZE\n") + reply = ser.readline().rstrip() + if("NOK" in reply): + sys.stderr.write("Error writing to USRP2+. Try again.\n") + raise SystemExit(1) + elif("OK" in reply): + sectorsize = int(reply[3:5], 16) + print("USRP2+ found with sector size %i. Erasing old image." % 2**sectorsize) + else: + sys.stderr.write("Invalid response or no USRP2+ connected.\n") + raise SystemExit(1) + + if(options.image == 1): + sectors = range(127, 128) + runcmd = "!RUNSFD\n" + elif(options.image == 2): + sectors = range(64, 65) + runcmd = "!RUNPFD\n" + elif(options.image == 3): + sectors = range(0,32) + runcmd = "!RUNSFPGA\n" + elif(options.image == 4): + sectors = range(32,64) + runcmd = "!RUNPFPGA\n" + + writeaddr = sectors[0] << sectorsize + if(options.image < 3): + writeaddr -= 0x8000 #i know this is awkward, but we subtract 0x8000 from the address for firmware loads. the reason we do this is that the IHX files are located at 0x8000 (RAM_BASE), and + #doing this here allows us to use the same IHX files for RAM load as for Flash load, without relocating in objcopy or relinking with another ld script. + #this limits us to writing above 32K for our firmware images. since the safe FPGA image located at 0x00000000 takes up 2MB of space this isn't really a worry. + #FPGA images (.mcs) always start at 0x00000000 so they don't need this relocation. + + for sector in sectors: + print "Erasing sector %i" % sector + ser.write("!ERASE %i\n" % sector) + reply = ser.readline() + if("NOK" in reply): + sys.stderr.write("Error erasing sector %i" % sector) + raise SystemExit(1) + + print "Setting start address to %i" % writeaddr + ser.write("!SETADDR %i\n" % writeaddr) + if("NOK" in reply): + sys.stderr.write("Error setting address\n") + raise SystemExit(1) + else: + print reply + + + for line in f: + ser.write(line.rstrip()+'\n') + reply = ser.readline() + if("NOK" in reply): #TODO: simplify this logic, use (reply.rstrip() is "NOK") + print("Received NOK reply during data write") + raise SystemExit(1) + elif("DONE" in reply): + print("Finished writing program. Loading...\n") + ser.write(runcmd) + elif("OK" not in reply): + print("Received invalid reply %s during data write" % reply) + raise SystemExit(1) + else: + print reply.rstrip() + '\t' + line.rstrip() + + print ser.readline() + + +if __name__ == '__main__': + main() diff --git a/firmware/microblaze/bin/uart_ihex_ram_loader.py b/firmware/microblaze/bin/uart_ihex_ram_loader.py new file mode 100755 index 000000000..c90fbe1d8 --- /dev/null +++ b/firmware/microblaze/bin/uart_ihex_ram_loader.py @@ -0,0 +1,70 @@ +#!/usr/bin/python + +import serial +from optparse import OptionParser +import os, sys + +def main(): + usage="%prog: [options] filename" + parser = OptionParser(usage=usage) + parser.add_option("-t", "--tty", type="string", default="/dev/ttyUSB0", + help="select serial port [default=%default]") + parser.add_option("-b", "--baudrate", type=int, default=115200, + help="set baudrate [default=%default]") + + (options, args) = parser.parse_args() + if len(args) != 1: + parser.print_help() + raise SystemExit(1) + + filename = args[0] + f = open(filename, "r") + + #all we have to do is load the IHX file and attempt to spit it out to the serial port. + if(os.path.exists(options.tty) is False): + sys.stderr.write("No serial port found at %s\n" % options.tty) + raise SystemExit(1) + + try: + ser = serial.Serial(port=options.tty, timeout=1, baudrate=options.baudrate, bytesize=8, parity=serial.PARITY_NONE, stopbits=1, rtscts=0, xonxoff=0) + except serial.SerialException: + sys.stderr.write("Unable to open serial port\n") + raise SystemExit(1) + + ser.open() + +#test to see if a valid USRP2+ in RAM load mode is connected + + ser.write("WOOOOO\n"); + reply = ser.readline() + if("NOK" not in reply): + sys.stderr.write("Valid USRP2+ not connected or no response received\n") + raise SystemExit(1) + else: + print("USRP2+ found.") + + for line in f: + ser.write(line.rstrip() + '\n') + reply = ser.readline() + if("NOK" in reply): #blocks to wait for response + print("Received NOK reply from USRP2+") + raise SystemExit(1) + elif("OK" not in reply): + print("Received invalid reply!") + raise SystemExit(1) +# else: +# print("OK received") + + print "USRP2+ RAM programmed.\nLoading program." + + #at this point it should have sent the end line of the file, which starts the program! + #we'll just act like a dumb terminal now +# ser.timeout = 0 +# try: +# while 1: +# print ser.readline() +# except KeyboardInterrupt: +# raise SystemExit(0) + +if __name__ == '__main__': + main() diff --git a/firmware/microblaze/bootstrap b/firmware/microblaze/bootstrap index 5786c1624..26987b0ec 100755 --- a/firmware/microblaze/bootstrap +++ b/firmware/microblaze/bootstrap @@ -18,6 +18,7 @@ rm -rf *.cache rm -rf libusrp2/.deps +rm -rf libusrp2p/.deps aclocal autoconf diff --git a/firmware/microblaze/configure.ac b/firmware/microblaze/configure.ac index e27bcb557..f6986f2dd 100644 --- a/firmware/microblaze/configure.ac +++ b/firmware/microblaze/configure.ac @@ -47,6 +47,8 @@ AC_PATH_PROG([HEXDUMP], [hexdump]) ################################################## AC_CONFIG_FILES([ \ Makefile \ + usrp2p/bootloader/Makefile \ usrp2/Makefile \ + usrp2p/Makefile \ ]) AC_OUTPUT diff --git a/firmware/microblaze/lib/Makefile.inc b/firmware/microblaze/lib/Makefile.inc index a576d1ccb..349ff2cd0 100644 --- a/firmware/microblaze/lib/Makefile.inc +++ b/firmware/microblaze/lib/Makefile.inc @@ -32,6 +32,7 @@ COMMON_SRCS = \ $(top_srcdir)/lib/hal_io.c \ $(top_srcdir)/lib/hal_uart.c \ $(top_srcdir)/lib/i2c.c \ + $(top_srcdir)/lib/i2c_async.c \ $(top_srcdir)/lib/mdelay.c \ $(top_srcdir)/lib/memcpy_wa.c \ $(top_srcdir)/lib/memset_wa.c \ @@ -41,6 +42,7 @@ COMMON_SRCS = \ $(top_srcdir)/lib/print_rmon_regs.c \ $(top_srcdir)/lib/print_buffer.c \ $(top_srcdir)/lib/printf.c \ + $(top_srcdir)/lib/ihex.c \ $(top_srcdir)/lib/spi.c \ $(top_srcdir)/lib/net_common.c \ $(top_srcdir)/lib/arp_cache.c \ diff --git a/firmware/microblaze/lib/bootconfig.c b/firmware/microblaze/lib/bootconfig.c new file mode 100644 index 000000000..93adc05c2 --- /dev/null +++ b/firmware/microblaze/lib/bootconfig.c @@ -0,0 +1,101 @@ +/* -*- c -*- */ +/* + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#ifdef HAVE_CONFIG_H +#include <config.h> +#endif +#include "bootconfig.h" +#include "bootconfig_private.h" +#include <stdint.h> +#include <stddef.h> +#include <i2c.h> +#include <quadradio/i2c_addr.h> +#include <mdelay.h> +#include <xilinx_v5_icap.h> +#include <nonstdio.h> + +eeprom_boot_info_t eeprom_shadow; + +static eeprom_boot_info_t eeprom_default = { + .magic = EEPROM_BOOT_INFO_MAGIC, + .nattempts = 1, + .next_boot.fpga_image_number = 0, + .next_boot.firmware_image_number = 0, + .default_boot.fpga_image_number = 0, + .default_boot.firmware_image_number = 0 +}; + +eeprom_boot_info_t * +_bc_get_eeprom_shadow(void) +{ + return &eeprom_shadow; +} + + +bool +_bc_write_eeprom_shadow(void) +{ + return eeprom_write(I2C_ADDR_MBOARD, BOOT_INFO_OFFSET, &eeprom_shadow, sizeof(eeprom_shadow)); +} + +void +bootconfig_init(void) +{ + if (!eeprom_read(I2C_ADDR_MBOARD, BOOT_INFO_OFFSET, &eeprom_shadow, sizeof(eeprom_shadow)) + || eeprom_shadow.magic != EEPROM_BOOT_INFO_MAGIC){ + eeprom_shadow = eeprom_default; + _bc_write_eeprom_shadow(); + } +} + +bootconfig_t +bootconfig_get_default(void) +{ + return eeprom_shadow.default_boot; +} + +bool +bootconfig_set_default(bootconfig_t bc) +{ + if (!validate_bootconfig(bc)) + return false; + + eeprom_shadow.default_boot = bc; + eeprom_shadow.next_boot = bc; + return _bc_write_eeprom_shadow(); +} + +void +bootconfig_boot(bootconfig_t bc) +{ + if (!validate_bootconfig(bc)) + return; + + eeprom_shadow.next_boot = bc; + eeprom_shadow.nattempts = 1; + _bc_write_eeprom_shadow(); + + if (1){ + puts("\nbootconfig: chaining to FPGA slot 0 bootloader"); + mdelay(100); + } + + while (1){ + // Reload fpga with code from SPI flash address 0x0. + icap_reload_fpga(0x00000000); + } +} diff --git a/firmware/microblaze/lib/gdbstub2.c b/firmware/microblaze/lib/gdbstub2.c new file mode 100644 index 000000000..4c63dfce2 --- /dev/null +++ b/firmware/microblaze/lib/gdbstub2.c @@ -0,0 +1,506 @@ +/* -*- c++ -*- */ +/* + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +/* + * Implement a eensy weensy part of the GDB Remote Serial Protocol + * + * See Appendix D of the GDB manual + * + * m<addr>,<length> -- read <length> bytes of memory starting at <addr> + * Reply: + * XX... XX... is memory contents in hex + * ENN ENN NN is a hex error number + * + * M<addr>,<length>:XX... -- write memory, data in hex + * Reply: + * OK for success + * ENN for an error. NN is a hex error number + * + * X<addr>,<length>:XX... -- write memory, data in binary + * Reply: + * OK for success + * ENN for an error. NN is a hex error number + * + * c<addr> -- continue. <addr> is the address to resume (goto). + * Reply: <none> + * + * \x80 New Format... + */ + +#include "gdbstub2.h" +#include "loader_parser.h" +#include "hal_uart.h" +#include <stdbool.h> +#include <stddef.h> + +#define MAX_PACKET 1024 + +/* + * Get raw character from serial port, no echo. + */ +static inline int +gdb_getc(void) +{ + return hal_uart_getc(); +} + +/* + * Put character to serial port. Raw output. + */ +static inline void +gdb_putc(int ch) +{ + hal_uart_putc(ch); +} + +// ------------------------------------------------------------------------ + +#define GDB_ESCAPE 0x7d + +static unsigned char hex_table[16] = { + '0', '1', '2', '3', '4', '5', '6', '7', + '8', '9', 'a', 'b', 'c', 'd', 'e', 'f' +}; + +static int +put_hex8_checksum(int ch, int checksum) +{ + unsigned char t = hex_table[(ch >> 4) & 0xf]; + checksum += t; + gdb_putc(t); + + t = hex_table[ch & 0xf]; + checksum += t; + gdb_putc(t); + return checksum; +} + +static void +put_hex8(int ch) +{ + put_hex8_checksum(ch, 0); +} + +static bool +hex4_to_bin(int ch, int *value) +{ + if ('0' <= ch && ch <= '9'){ + *value = ch - '0'; + return true; + } + if ('a' <= ch && ch <= 'f'){ + *value = ch - 'a' + 10; + return true; + } + if ('A' <= ch && ch <= 'F'){ + *value = ch - 'A' + 10; + return true; + } + *value = 0; + return false; +} + +static bool +hex8_to_bin(const unsigned char *s, int *value) +{ + int v0, v1; + if (hex4_to_bin(s[0], &v0) && hex4_to_bin(s[1], &v1)){ + *value = (v0 << 4) | v1; + return true; + } + return false; +} + +static bool +hex_to_bin_array(unsigned char *binary_data, const unsigned char *hex_data, size_t nbytes) +{ + for (size_t i = 0; i < nbytes; i++){ + int t; + if (!hex8_to_bin(&hex_data[2*i], &t)) + return false; + binary_data[i] = t; + } + return true; +} + +static bool +needs_escaping(int ch) +{ + return ch == '$' || ch == '#' || ch == GDB_ESCAPE; +} + +/* + * \brief Wait for a packet. + * \param[out] pkt_buf gets the received packet payload. + * \param[in] max_size is the maximum number of bytes to write into \p pkt_buf. + * \param[out] actual_size is the number of bytes written to \p pkt_buf. + * + * \returns true iff the payload fits and the checksum is OK. + * + * Packets have this format: + * + * $<packet-data>#<checksum> + * + * Where <packet-data> is anything and <checksum> is a two byte hex + * checksum. In <packet-data> '$', '#' and 0x7d are escaped with 0x7d. + * The checksum is computed as the modulo 256 sum of all characters + * btween the leading '$' and the trailing '#' (an 8-bit unsigned + * checksum). + */ +static bool +get_packet(unsigned char *pkt_buf, size_t max_size, size_t *actual_size) +{ + typedef enum states { + LOOKING_FOR_DOLLAR, + LOOKING_FOR_HASH, + CSUM1, + CSUM2, + } state_t; + + *actual_size = 0; + unsigned char csum[2] = {0, 0}; + state_t state = LOOKING_FOR_DOLLAR; + size_t pi = 0; + + while (1){ + int ch = gdb_getc(); + + switch (state){ + case LOOKING_FOR_DOLLAR: + if (ch == '$'){ + pi = 0; + state = LOOKING_FOR_HASH; + } + else if (ch == '#'){ // most likely missed the $ + return false; + } + break; + + case LOOKING_FOR_HASH: + if (ch == '$'){ + return false; + } + else if (ch == '#'){ + state = CSUM1; + } + else { + if (pi >= max_size) // payload too big + return false; + + if (ch == GDB_ESCAPE) + ch = gdb_getc(); + + pkt_buf[pi++] = ch; + } + break; + + case CSUM1: + csum[0] = ch; + state = CSUM2; + break; + + case CSUM2: + csum[1] = ch; + *actual_size = pi; + + // accept .. as a correct checksum + if (csum[0] == '.' && csum[1] == '.') + return true; + + int expected_checksum; + if (!hex8_to_bin(csum, &expected_checksum)) + return false; + + int checksum = 0; + for (size_t i = 0; i < pi; i++) + checksum += pkt_buf[i]; + + checksum &= 0xff; + return checksum == expected_checksum; + } + } +} + +static void +put_packet_trailer(int checksum) +{ + gdb_putc('#'); + put_hex8(checksum & 0xff); + gdb_putc('\r'); + gdb_putc('\n'); +} + +static void +put_packet(const unsigned char *pkt_buf, size_t size) +{ + gdb_putc('$'); + + int checksum = 0; + for (size_t i = 0; i < size; i++){ + int ch = pkt_buf[i]; + if (needs_escaping(ch)) + gdb_putc(GDB_ESCAPE); + gdb_putc(ch); + checksum += ch; + } + put_packet_trailer(checksum); +} + +/*! + * Read a hex number + * + * \param[inout] bufptr - pointer to pointer to buffer (updated on return) + * \param[in] end - one past end of valid data in buf + * \param[out] value - the parsed value + * + * \returns true iff a valid hex number was read from bufptr + */ +static bool +parse_number(const unsigned char **bufptr, const unsigned char *end, unsigned int *value) +{ + const unsigned char *buf = *bufptr; + unsigned int v = 0; + bool valid = false; + int nibble; + + while (buf < end && hex4_to_bin(*buf, &nibble)){ + valid = true; + v = (v << 4) | nibble; + buf++; + } + + *value = v; + *bufptr = buf; + return valid; +} + +static bool +parse_char(const unsigned char **bufptr, const unsigned char *end, unsigned char *ch) +{ + const unsigned char *buf = *bufptr; + if (buf < end){ + *ch = *buf++; + *bufptr = buf; + return true; + } + return false; +} + +static bool +expect_char(const unsigned char **bufptr, const unsigned char *end, unsigned char expected) +{ + unsigned char ch; + return parse_char(bufptr, end, &ch) && ch == expected; +} + +static bool +expect_end(const unsigned char **bufptr, const unsigned char *end) +{ + return *bufptr == end; +} + +static bool +parse_addr_length(const unsigned char **bufptr, const unsigned char *end, + unsigned int *addr, unsigned int *length) +{ + return (parse_number(bufptr, end, addr) + && expect_char(bufptr, end, ',') + && parse_number(bufptr, end, length)); +} + +static void +put_error(int error) +{ + unsigned char buf[3]; + buf[0] = 'E'; + buf[1] = hex_table[(error >> 4) & 0xf]; + buf[2] = hex_table[error & 0xf]; + + put_packet(buf, sizeof(buf)); +} + +static void +put_ok(void) +{ + const unsigned char buf[2] = "OK"; + put_packet(buf, sizeof(buf)); +} + +/* + * Read memory and send the reply. + * We do it on the fly so that our packet size is effectively unlimited + */ +static void +read_memory(unsigned int addr, unsigned int nbytes) +{ + int checksum = 0; + gdb_putc('$'); + + if ((addr & 0x3) == 0 && (nbytes & 0x3) == 0){ // word aligned + union { + unsigned int i; + unsigned char c[4]; + } u; + + unsigned int *p = (unsigned int *) addr; + unsigned int length = nbytes / 4; + + for (unsigned int i = 0; i < length; i++){ + u.i = p[i]; // do a word read + checksum = put_hex8_checksum(u.c[0], checksum); + checksum = put_hex8_checksum(u.c[1], checksum); + checksum = put_hex8_checksum(u.c[2], checksum); + checksum = put_hex8_checksum(u.c[3], checksum); + } + } + else { // byte aligned + unsigned char *p = (unsigned char *) addr; + for (unsigned int i = 0; i < nbytes; i++) + checksum = put_hex8_checksum(p[i], checksum); + } + + put_packet_trailer(checksum); +} + +static unsigned int +get_unaligned_int(const unsigned char *p) +{ + // we're bigendian + return (p[0] << 24) | (p[1] << 16) | (p[2] << 8) | (p[3]); +} + +static bool +write_memory(unsigned int addr, size_t nbytes, + const unsigned char *data) +{ + if ((addr & 0x3) == 0 && (nbytes & 0x3) == 0){ // word-aligned dst + unsigned int *dst = (unsigned int *) addr; + size_t length = nbytes / 4; + for (size_t i = 0; i < length; i++){ + unsigned int t = get_unaligned_int(&data[4*i]); + dst[i] = t; // word writes + } + } + else { // non-word-aligned dst + unsigned char *dst = (unsigned char *) addr; + for (size_t i = 0; i < nbytes; i++){ + dst[i] = data[i]; + } + } + return true; +} + +void +gdbstub2_main_loop(void) +{ + unsigned char inpkt[MAX_PACKET + 24]; + unsigned char binary_data[MAX_PACKET/2] __attribute__((aligned (4))); + + hal_uart_set_mode(UART_MODE_RAW); //tell UART HAL not to map \n to \r\n + + while (1){ + size_t inpkt_len; + bool ok = get_packet(inpkt, sizeof(inpkt), &inpkt_len); + if (!ok){ + gdb_putc('-'); + continue; + } + gdb_putc('+'); + + const unsigned char *buf = inpkt; + const unsigned char *end = inpkt + inpkt_len; + unsigned char ch; + + if (!parse_char(&buf, end, &ch)){ // empty packet + put_packet(0, 0); + continue; + } + + unsigned int addr; + unsigned int length; + + switch(ch){ + case 'm': // m<addr>,<length> -- read <length> bytes starting at <addr> + if (!(parse_addr_length(&buf, end, &addr, &length) && expect_end(&buf, end))){ + put_error(1); + } + else { + read_memory(addr, length); + } + break; + + case 'M': // M<addr>,<length>:XX... -- write <length> bytes starting at <addr> + // XX... is the data in hex + if (!(parse_addr_length(&buf, end, &addr, &length) + && expect_char(&buf, end, ':') + && (end - buf) == 2 * length)){ + put_error(1); + } + else { + if (!hex_to_bin_array(binary_data, buf, length)) + put_error(2); + else if (!write_memory(addr, length, binary_data)) + put_error(3); + else + put_ok(); + } + break; + + case 'X': // X<addr>,<length>:XX... -- write <length> bytes starting at <addr> + // XX... is the data in binary + if (!(parse_addr_length(&buf, end, &addr, &length) + && expect_char(&buf, end, ':') + && (end - buf) == length)){ + put_error(1); + } + else { + if (!write_memory(addr, length, buf)) + put_error(3); + else + put_ok(); + } + break; + + case 'c': // c<addr> -- continue. <addr> is the address to resume (goto). + if (!(parse_number(&buf, end, &addr) + && expect_end(&buf, end))){ + put_error(1); + } + else { + typedef void (*fptr_t)(void); + (*(fptr_t) addr)(); // most likely no return + } + break; +/* + case 0x80: + { + unsigned char *output = binary_data; // reuse + size_t sizeof_output = sizeof(binary_data); + size_t actual_olen; + loader_parser(buf, end-buf, + output, sizeof_output, &actual_olen); + put_packet(output, actual_olen); + } + break; +*/ + default: // unknown packet type + put_packet(0, 0); + break; + } + } +} diff --git a/firmware/microblaze/lib/gdbstub2.h b/firmware/microblaze/lib/gdbstub2.h new file mode 100644 index 000000000..15cdde939 --- /dev/null +++ b/firmware/microblaze/lib/gdbstub2.h @@ -0,0 +1,25 @@ +/* -*- c++ -*- */ +/* + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef INCLUDED_GDBSTUB_H +#define INCLUDED_GDBSTUB_H + +void gdbstub2_main_loop(void); + +#endif /* INCLUDED_GDBSTUB_H */ + diff --git a/firmware/microblaze/lib/hal_io.c b/firmware/microblaze/lib/hal_io.c index 58b1e681e..be4c570c7 100644 --- a/firmware/microblaze/lib/hal_io.c +++ b/firmware/microblaze/lib/hal_io.c @@ -18,9 +18,9 @@ // conditionalized on HAL_IO_USES_DBOARD_PINS && HAL_IO_USES_UART -#include "hal_io.h" #include "memory_map.h" #include "hal_uart.h" +#include "hal_io.h" #include <stdbool.h> #include <stdio.h> #include <string.h> @@ -124,16 +124,29 @@ hal_finish(void) // %c inline int +fputchar(hal_uart_name_t u, int ch) +{ + hal_uart_putc(u, ch); + return ch; +} + +inline int putchar(int ch) { - hal_uart_putc(ch); + hal_uart_putc(DEFAULT_UART, ch); return ch; } int +fgetchar(hal_uart_name_t u) +{ + return hal_uart_getc(u); +} + +int getchar(void) { - return hal_uart_getc(); + return fgetchar(DEFAULT_UART); } #else // nop all i/o @@ -172,34 +185,87 @@ getchar(void) // \n inline void +fnewline(hal_uart_name_t u) +{ + fputchar(u, '\n'); +} + +inline void newline(void) { - putchar('\n'); + fnewline(DEFAULT_UART); } int -putstr(const char *s) +fputstr(hal_uart_name_t u, const char *s) { while (*s) - putchar(*s++); + fputchar(u, *s++); return 0; } int -puts(const char *s) +fnputstr(hal_uart_name_t u, const char *s, int len) +{ + int x = 0; + while (*s && (len > x++)) + fputchar(u, *s++); + + return x; +} + +int +putstr(const char *s) { - putstr(s); - putchar('\n'); + return fputstr(DEFAULT_UART, s); +} + +int +fputs(hal_uart_name_t u, const char *s) +{ + fputstr(u, s); + fputchar(u, '\n'); return 0; } +int puts(const char *s) +{ + return fputs(DEFAULT_UART, s); +} + +char * +fgets(hal_uart_name_t u, char * const s) +{ + char *x = s; + while((*x=(char)hal_uart_getc(u)) != '\n') x++; + *x = 0; + return s; +} + +int +fngets(hal_uart_name_t u, char * const s, int len) +{ + char *x = s; + while(((*x=(char)hal_uart_getc(u)) != '\n') && ((x-s) < len)) x++; + *x = 0; + return (x-s); +} + +int +fngets_timeout(hal_uart_name_t u, char * const s, int len) +{ + char *x = s; + + while(((*x=(char)hal_uart_getc_timeout(u)) != '\n') && (*x != -1) && ((x-s) < len)) x++; + *x = 0; + //printf("Returning from fngets() with string %d of length %d\n", s[0], x-s); + return (x-s); +} + char * gets(char * const s) { - char *x = s; - while((*x=(char)hal_uart_getc()) != '\n') x++; - *x = 0; - return s; + return fgets(DEFAULT_UART, s); } diff --git a/firmware/microblaze/lib/hal_io.h b/firmware/microblaze/lib/hal_io.h index c67d96c62..950f8d591 100644 --- a/firmware/microblaze/lib/hal_io.h +++ b/firmware/microblaze/lib/hal_io.h @@ -20,10 +20,15 @@ #define INCLUDED_HAL_IO_H #include "memory_map.h" +#include "hal_uart.h" void hal_io_init(void); void hal_finish(); char *gets(char * const s); +int fputstr(hal_uart_name_t u, const char *s); +int fnputstr(hal_uart_name_t u, const char *s, int len); +int fngets(hal_uart_name_t u, char * const s, int len); +int fngets_timeout(hal_uart_name_t u, char * const s, int len); /* * ------------------------------------------------------------------------ diff --git a/firmware/microblaze/lib/hal_uart.c b/firmware/microblaze/lib/hal_uart.c index fe3b7515a..7836240fe 100644 --- a/firmware/microblaze/lib/hal_uart.c +++ b/firmware/microblaze/lib/hal_uart.c @@ -16,71 +16,105 @@ * along with this program. If not, see <http://www.gnu.org/licenses/>. */ +#include "memory_map.h" #include "hal_uart.h" #include "hal_io.h" -#include "memory_map.h" +#include "mdelay.h" -// First pass, no interrupts - -// Replaced with divisors.py which generates best divisor -//#define CALC_DIVISOR(rate) (WISHBONE_CLK_RATE / ((rate) * 16)) +//just to save you from going insane, note that firmware/FPGA UARTs [0-2] correspond to serial ports [1-3]. +//so in software, we refer to UART_DEBUG as UART0, but it transmits on pin TXD<1>. see the UART assignments in hal_uart.h. #define NSPEEDS 6 #define MAX_WB_DIV 4 +//if you're going to recalculate the divisors, it's just uart_clock_rate / baud_rate. +//uart_clock_rate is 50MHz for USRP2. static const uint16_t -divisor_table[MAX_WB_DIV+1][NSPEEDS] = { - { 2, 2, 2, 2, 2, 2}, // 0: can't happen - { 651, 326, 163, 109, 54, 27 }, // 1: 100 MHz - { 326, 163, 81, 54, 27, 14 }, // 2: 50 MHz - { 217, 109, 54, 36, 18, 9 }, // 3: 33.3333 MHz - { 163, 81, 41, 27, 14, 7 }, // 4: 25 MHz +divisor_table[NSPEEDS] = { + 5208, // 9600 + 2604, // 19200 + 1302, // 38400 + 868, // 57600 + 434, // 115200 + 217 // 230400 }; -#define u uart_regs +static char uart_mode[4] = { + [UART_DEBUG] = UART_MODE_ONLCR, + [UART_EXP] = UART_MODE_ONLCR, + [UART_GPS] = UART_MODE_ONLCR +}; -static char uart_mode = UART_MODE_ONLCR; +static char uart_speeds[4] = { + [UART_DEBUG] = US_230400, + [UART_EXP] = US_230400, + [UART_GPS] = US_115200 +}; void -hal_uart_set_mode(int mode) +hal_uart_set_mode(hal_uart_name_t uart, int mode) +{ + uart_mode[uart] = mode; +} + +void hal_uart_set_speed(hal_uart_name_t uart, hal_uart_speed_t speed) { - uart_mode = mode; + uart_regs[uart].clkdiv = divisor_table[speed]; } void hal_uart_init(void) { - hal_uart_set_mode(UART_MODE_ONLCR); - u->clkdiv = 217; // 230400 bps + for(int i = 0; i < 3; i++) { + hal_uart_set_mode(i, uart_mode[i]); + hal_uart_set_speed(i, uart_speeds[i]); + } } void -hal_uart_putc(int ch) +hal_uart_putc(hal_uart_name_t u, int ch) { - if (ch == '\n')// && (uart_mode == UART_MODE_ONLCR)) //map \n->\r\n if necessary - hal_uart_putc('\r'); + if ((ch == '\n') && (uart_mode[u] == UART_MODE_ONLCR)) //map \n->\r\n if necessary + hal_uart_putc(u, '\r'); - while (u->txlevel == 0) // wait for fifo to have space + while (uart_regs[u].txlevel == 0) // wait for fifo to have space ; - u->txchar = ch; + uart_regs[u].txchar = ch; } void -hal_uart_putc_nowait(int ch) +hal_uart_putc_nowait(hal_uart_name_t u, int ch) { - if (ch == '\n')// && (uart_mode == UART_MODE_ONLCR)) //map \n->\r\n if necessary - hal_uart_putc('\r'); + if ((ch == '\n') && (uart_mode[u] == UART_MODE_ONLCR)) //map \n->\r\n if necessary + hal_uart_putc(u, '\r'); - if(u->txlevel) // If fifo has space - u->txchar = ch; + if(uart_regs[u].txlevel) // If fifo has space + uart_regs[u].txchar = ch; } int -hal_uart_getc(void) +hal_uart_getc(hal_uart_name_t u) { - while ((u->rxlevel) == 0) // wait for data to be ready + while ((uart_regs[u].rxlevel) == 0) // wait for data to be ready ; - return u->rxchar; + return uart_regs[u].rxchar; } + +int +hal_uart_getc_timeout(hal_uart_name_t u) +{ + int timeout = 0; + while (((uart_regs[u].rxlevel) == 0) && (timeout++ < HAL_UART_TIMEOUT_MS)) + mdelay(1); + return (timeout >= HAL_UART_TIMEOUT_MS) ? -1 : uart_regs[u].rxchar; //return -1 if nothing there, cause fngets to quit +} + +int hal_uart_rx_flush(hal_uart_name_t u) +{ + char x; + while(uart_regs[u].rxlevel) x = uart_regs[u].rxchar; + return x; +} + diff --git a/firmware/microblaze/lib/hal_uart.h b/firmware/microblaze/lib/hal_uart.h index dfd73c323..758c8cb5e 100644 --- a/firmware/microblaze/lib/hal_uart.h +++ b/firmware/microblaze/lib/hal_uart.h @@ -25,29 +25,39 @@ #define UART_MODE_RAW 0x0000 // no mapping on input or output #define UART_MODE_ONLCR 0x0001 // map \n to \r\n on output (default) -/* - * \brief Set uart mode - */ -void hal_uart_set_mode(int flags); +#define DEFAULT_UART UART_DEBUG //which UART printf, gets, etc. use -/*! - * \brief one-time call to init - */ -void hal_uart_init(void); +#define HAL_UART_TIMEOUT_MS 300 typedef enum { - US_9600, - US_19200, - US_38400, - US_57600, - US_115200, - US_230400, + US_9600 = 0, + US_19200 = 1, + US_38400 = 2, + US_57600 = 3, + US_115200 = 4, + US_230400 = 5 } hal_uart_speed_t; typedef struct { hal_uart_speed_t speed; } hal_uart_config_t; +typedef enum { + UART_DEBUG = 0, + UART_EXP = 1, + UART_GPS = 2 +} hal_uart_name_t; + +/* + * \brief Set uart mode + */ +void hal_uart_set_mode(hal_uart_name_t uart, int flags); + +/*! + * \brief one-time call to init + */ +void hal_uart_init(void); + /*! * \brief Set uart parameters * Default is 115,200 bps, 8N1. @@ -62,17 +72,23 @@ void hal_uart_get_config(hal_uart_config_t *c); /*! * \brief Enqueue \p ch for output over serial port */ -void hal_uart_putc(int ch); +void hal_uart_putc(hal_uart_name_t u, int ch); /*! * \brief Enqueue \p ch for output over serial port, silent fail if queue is full */ -void hal_uart_putc_nowait(int ch); +void hal_uart_putc_nowait(hal_uart_name_t u, int ch); /* * \brief Blocking read of next char from serial port */ -int hal_uart_getc(void); +int hal_uart_getc(hal_uart_name_t u); + +/* + * \brief Blocking read of next char from serial port with timeout + */ +int hal_uart_getc_timeout(hal_uart_name_t u); +int hal_uart_rx_flush(hal_uart_name_t u); #endif /* INCLUDED_HAL_UART_H */ diff --git a/firmware/microblaze/lib/i2c.c b/firmware/microblaze/lib/i2c.c index 177341267..d230f462c 100644 --- a/firmware/microblaze/lib/i2c.c +++ b/firmware/microblaze/lib/i2c.c @@ -20,7 +20,6 @@ #include "memory_map.h" #include "stdint.h" #include <string.h> -#include "pic.h" #include "nonstdio.h" #define MAX_WB_DIV 4 // maximum wishbone divisor (from 100 MHz MASTER_CLK) @@ -37,18 +36,6 @@ static uint16_t prescaler_values[MAX_WB_DIV+1] = { PRESCALER(4), // 4: 25 MHz }; -//asynchronous (interrupt-driven) i2c state variables -volatile uint8_t i2c_buf[17]; //tx/rx data transfer buffer -volatile uint8_t *volatile i2c_bufptr = i2c_buf; //ptr to current position -volatile uint8_t i2c_len = 0; //length remaining in current transfer -volatile i2c_state_t i2c_state = I2C_STATE_IDLE; //current I2C transfer state -i2c_dir_t i2c_dir; //I2C transfer direction - -void (*volatile i2c_callback)(void); //function pointer to i2c callback to be called when transaction is complete - -static void i2c_irq_handler(unsigned irq); -inline void i2c_async_err(void); - void i2c_init(void) { @@ -64,8 +51,8 @@ i2c_init(void) i2c_regs->ctrl = I2C_CTRL_EN; //| I2C_CTRL_IE; // enable core - // FIXME interrupt driven? - pic_register_handler(IRQ_I2C, i2c_irq_handler); + //now this is done separately to maintain common code for async and sync + //pic_register_handler(IRQ_I2C, i2c_irq_handler); } static inline void @@ -140,163 +127,3 @@ i2c_write(unsigned char i2c_addr, const unsigned char *buf, unsigned int len) return false; } -static void i2c_irq_handler(unsigned irq) { -//i2c state machine. - - //printf("I2C irq handler\n"); - //first let's make sure nothing is f'ed up - //TODO: uncomment this error checking when we have some way to handle errors -// if(((i2c_regs->cmd_status & I2C_ST_RXACK) != 0) && i2c_dir == I2C_DIR_WRITE) { //we got a NACK and we didn't send it -// printf("\tNACK received\n"); -// i2c_async_err(); -// return; -// }// else printf("\tACK received, proceeding\n"); - - if(i2c_regs->cmd_status & I2C_ST_AL) { - printf("\tArbitration lost!\n"); - i2c_async_err(); - return; - } - - if(i2c_regs->cmd_status & I2C_ST_TIP) { - //printf("\tI2C still busy in interrupt\n"); - return; - } - - //now decide what to do - switch(i2c_state) { - - case I2C_STATE_IDLE: - //this is an error. in idle state, we shouldn't be transferring data, and the fact that the IRQ fired is terrible bad. - printf("AAAAAHHHHH INTERRUPT IN THE IDLE STATE AAAHHHHHHHHH\n"); - i2c_async_err(); - break; - - case I2C_STATE_CONTROL_BYTE_SENT: //here we've sent the control byte, and we're either clocking data in or out now, but we haven't received a byte yet. - case I2C_STATE_DATA: //here we're sending/receiving data and if we're receiving there's data in the data reg - - //if(i2c_state == I2C_STATE_DATA) printf("\tI2C in state DATA with dir=%d and len=%d\n", i2c_dir, i2c_len); - //else printf("\tI2C in state CONTROL_BYTE_SENT with dir=%d and len=%d\n", i2c_dir, i2c_len); - - if(i2c_dir == I2C_DIR_READ) { - if(i2c_state == I2C_STATE_DATA) *(i2c_bufptr++) = i2c_regs->data; - //printf("\tRead %x\n", *(i2c_bufptr-1)); - //set up another data byte - if(i2c_len > 1) //only one more byte to transfer - i2c_regs->cmd_status = I2C_CMD_RD; - else - i2c_regs->cmd_status = I2C_CMD_RD | I2C_CMD_NACK | I2C_CMD_STOP; - } - else if(i2c_dir == I2C_DIR_WRITE) { - //write a byte - //printf("\tWriting %x\n", *i2c_bufptr); - i2c_regs->data = *(i2c_bufptr++); - if(i2c_len > 1) - i2c_regs->cmd_status = I2C_CMD_WR; - else { - //printf("\tGenerating STOP\n"); - i2c_regs->cmd_status = I2C_CMD_WR | I2C_CMD_STOP; - } - }; - i2c_len--; - if(i2c_len == 0) i2c_state = I2C_STATE_LAST_BYTE; - else i2c_state = I2C_STATE_DATA; //takes care of the addr_sent->data transition - break; - - - case I2C_STATE_LAST_BYTE: //here we've already sent the last read request and the last data is waiting for us. - //printf("\tI2C in state LAST BYTE\n"); - - if(i2c_dir == I2C_DIR_READ) { - *(i2c_bufptr++) = i2c_regs->data; - //printf("\tRead %x\n", *(i2c_bufptr-1)); - i2c_state = I2C_STATE_DATA_READY; - } else { - i2c_state = I2C_STATE_IDLE; - } - i2c_regs->ctrl &= ~I2C_CTRL_IE; //disable interrupts until next time - - if(i2c_callback) { - i2c_callback(); //if we registered a callback, call it! - } - - break; - - - default: //terrible things have happened. - break; - } - -} - -void i2c_register_callback(void (*volatile callback)(void)) { - i2c_callback = callback; -} - -inline void i2c_async_err(void) { - i2c_state = I2C_STATE_IDLE; - i2c_regs->ctrl &= ~I2C_CTRL_IE; - printf("I2C error\n"); -//TODO: set an error flag instead of just dropping things on the floor - i2c_regs->cmd_status = I2C_CMD_STOP; -} - -bool i2c_async_read(uint8_t addr, unsigned int len) { - //printf("Starting async read\n"); - if(i2c_state != I2C_STATE_IDLE) return false; //sorry mario but your i2c is in another castle - if(len == 0) return true; //just idiot-proofing - if(len > sizeof(i2c_buf)) return false; - - //disable I2C interrupts and clear pending interrupts on the I2C device - i2c_regs->ctrl &= ~I2C_CTRL_IE; - i2c_regs->cmd_status |= I2C_CMD_IACK; - - i2c_len = len; - i2c_dir = I2C_DIR_READ; - i2c_bufptr = i2c_buf; - //then set up the transfer by issuing the control byte - i2c_regs->ctrl |= I2C_CTRL_IE; - i2c_regs->data = (addr << 1) | 0x01; //7 bit addr and read bit - i2c_regs->cmd_status = I2C_CMD_WR | I2C_CMD_START; //generate start & start writing addr - //update the state so the irq handler knows what's going on - i2c_state = I2C_STATE_CONTROL_BYTE_SENT; - return true; -} - -bool i2c_async_write(uint8_t addr, const uint8_t *buf, unsigned int len) { - //printf("Starting async write\n"); - if(i2c_state != I2C_STATE_IDLE) return false; //sorry mario but your i2c is in another castle - if(len > sizeof(i2c_buf)) return false; - - //disable I2C interrupts and clear pending interrupts on the I2C device - i2c_regs->ctrl &= ~I2C_CTRL_IE; - i2c_regs->cmd_status |= I2C_CMD_IACK; - - //copy the buffer into our own if writing - memcpy((void *)i2c_buf, buf, len); - - i2c_len = len; - i2c_dir = I2C_DIR_WRITE; - i2c_bufptr = i2c_buf; - //then set up the transfer by issuing the control byte - i2c_regs->ctrl |= I2C_CTRL_IE; - i2c_regs->data = (addr << 1) | 0x00; //7 bit addr and read bit - i2c_regs->cmd_status = I2C_CMD_WR | I2C_CMD_START; //generate start & start writing addr - //update the state so the irq handler knows what's going on - i2c_state = I2C_STATE_CONTROL_BYTE_SENT; - - return true; -} - -//TODO: determine if it's better to read sequentially into the user's buffer, copy on transfer complete, or copy on request (shown below). probably best to copy on request. -bool i2c_async_data_ready(void *buf) { - if(i2c_state == I2C_STATE_DATA_READY) { - i2c_state = I2C_STATE_IDLE; - memcpy(buf, (void *)i2c_buf, (i2c_bufptr - i2c_buf)); //TODO: not really comfortable with this - //printf("Copying %d bytes to user buffer\n", i2c_bufptr-i2c_buf); - return true; - } - return false; -} - - diff --git a/firmware/microblaze/lib/i2c.h b/firmware/microblaze/lib/i2c.h index 77129e922..6ff0e6982 100644 --- a/firmware/microblaze/lib/i2c.h +++ b/firmware/microblaze/lib/i2c.h @@ -22,36 +22,15 @@ #include <stdbool.h> #include "stdint.h" -typedef enum { I2C_STATE_IDLE, - I2C_STATE_CONTROL_BYTE_SENT, - I2C_STATE_DATA, - I2C_STATE_LAST_BYTE, - I2C_STATE_DATA_READY, - I2C_STATE_ERROR - } i2c_state_t; - -typedef enum { I2C_DIR_WRITE=0, I2C_DIR_READ=1 } i2c_dir_t; - void i2c_init(void); bool i2c_read (unsigned char i2c_addr, unsigned char *buf, unsigned int len); bool i2c_write(unsigned char i2c_addr, const unsigned char *buf, unsigned int len); -bool i2c_async_read(uint8_t addr, unsigned int len); -bool i2c_async_write(uint8_t addr, const uint8_t *buf, unsigned int len); -bool i2c_async_data_ready(void *); -//static void i2c_irq_handler(unsigned irq); -void i2c_register_callback(void (*callback)(void)); - -// Write 24LC024 / 24LC025 EEPROM on motherboard or daughterboard. -// Which EEPROM is determined by i2c_addr. See i2c_addr.h - bool eeprom_write (int i2c_addr, int eeprom_offset, const void *buf, int len); -bool eeprom_write_async (int i2c_addr, int eeprom_offset, const void *buf, int len, void (*callback)(void)); // Read 24LC024 / 24LC025 EEPROM on motherboard or daughterboard. // Which EEPROM is determined by i2c_addr. See i2c_addr.h bool eeprom_read (int i2c_addr, int eeprom_offset, void *buf, int len); -bool eeprom_read_async(int i2c_addr, int eeprom_offset, void *buf, int len, void (*callback)(void)); #endif /* INCLUDED_I2C_H */ diff --git a/firmware/microblaze/lib/i2c_async.c b/firmware/microblaze/lib/i2c_async.c new file mode 100644 index 000000000..05c4c3a09 --- /dev/null +++ b/firmware/microblaze/lib/i2c_async.c @@ -0,0 +1,206 @@ +// +// Copyright 2010 Ettus Research LLC +// +/* + * Copyright 2007,2008 Free Software Foundation, Inc. + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + + //i2c_async.c: asynchronous (interrupt-driven) routines for I2C. + //separated out here so we can have a small I2C lib for bootloader and + //retain interrupt-driven I2C for the main app. + +#include "memory_map.h" +#include "stdint.h" +#include <string.h> +#include "pic.h" +#include "nonstdio.h" +#include "i2c_async.h" + + //asynchronous (interrupt-driven) i2c state variables +volatile uint8_t i2c_buf[17]; //tx/rx data transfer buffer +volatile uint8_t *volatile i2c_bufptr = i2c_buf; //ptr to current position +volatile uint8_t i2c_len = 0; //length remaining in current transfer +volatile i2c_state_t i2c_state = I2C_STATE_IDLE; //current I2C transfer state +i2c_dir_t i2c_dir; //I2C transfer direction + +void (*volatile i2c_callback)(void); //function pointer to i2c callback to be called when transaction is complete +static void i2c_irq_handler(unsigned irq); +inline void i2c_async_err(void); + +void i2c_register_handler(void) { + pic_register_handler(IRQ_I2C, i2c_irq_handler); +} + + +static void i2c_irq_handler(unsigned irq) { +//i2c state machine. + + //printf("I2C irq handler\n"); + //first let's make sure nothing is f'ed up + //TODO: uncomment this error checking when we have some way to handle errors +// if(((i2c_regs->cmd_status & I2C_ST_RXACK) != 0) && i2c_dir == I2C_DIR_WRITE) { //we got a NACK and we didn't send it +// printf("\tNACK received\n"); +// i2c_async_err(); +// return; +// }// else printf("\tACK received, proceeding\n"); + + if(i2c_regs->cmd_status & I2C_ST_AL) { + printf("\tArbitration lost!\n"); + i2c_async_err(); + return; + } + + if(i2c_regs->cmd_status & I2C_ST_TIP) { + //printf("\tI2C still busy in interrupt\n"); + return; + } + + //now decide what to do + switch(i2c_state) { + + case I2C_STATE_IDLE: + //this is an error. in idle state, we shouldn't be transferring data, and the fact that the IRQ fired is terrible bad. + printf("AAAAAHHHHH INTERRUPT IN THE IDLE STATE AAAHHHHHHHHH\n"); + i2c_async_err(); + break; + + case I2C_STATE_CONTROL_BYTE_SENT: //here we've sent the control byte, and we're either clocking data in or out now, but we haven't received a byte yet. + case I2C_STATE_DATA: //here we're sending/receiving data and if we're receiving there's data in the data reg + + //if(i2c_state == I2C_STATE_DATA) printf("\tI2C in state DATA with dir=%d and len=%d\n", i2c_dir, i2c_len); + //else printf("\tI2C in state CONTROL_BYTE_SENT with dir=%d and len=%d\n", i2c_dir, i2c_len); + + if(i2c_dir == I2C_DIR_READ) { + if(i2c_state == I2C_STATE_DATA) *(i2c_bufptr++) = i2c_regs->data; + //printf("\tRead %x\n", *(i2c_bufptr-1)); + //set up another data byte + if(i2c_len > 1) //only one more byte to transfer + i2c_regs->cmd_status = I2C_CMD_RD; + else + i2c_regs->cmd_status = I2C_CMD_RD | I2C_CMD_NACK | I2C_CMD_STOP; + } + else if(i2c_dir == I2C_DIR_WRITE) { + //write a byte + //printf("\tWriting %x\n", *i2c_bufptr); + i2c_regs->data = *(i2c_bufptr++); + if(i2c_len > 1) + i2c_regs->cmd_status = I2C_CMD_WR; + else { + //printf("\tGenerating STOP\n"); + i2c_regs->cmd_status = I2C_CMD_WR | I2C_CMD_STOP; + } + }; + i2c_len--; + if(i2c_len == 0) i2c_state = I2C_STATE_LAST_BYTE; + else i2c_state = I2C_STATE_DATA; //takes care of the addr_sent->data transition + break; + + + case I2C_STATE_LAST_BYTE: //here we've already sent the last read request and the last data is waiting for us. + //printf("\tI2C in state LAST BYTE\n"); + + if(i2c_dir == I2C_DIR_READ) { + *(i2c_bufptr++) = i2c_regs->data; + //printf("\tRead %x\n", *(i2c_bufptr-1)); + i2c_state = I2C_STATE_DATA_READY; + } else { + i2c_state = I2C_STATE_IDLE; + } + i2c_regs->ctrl &= ~I2C_CTRL_IE; //disable interrupts until next time + + if(i2c_callback) { + i2c_callback(); //if we registered a callback, call it! + } + + break; + + + default: //terrible things have happened. + break; + } + +} + +void i2c_register_callback(void (*volatile callback)(void)) { + i2c_callback = callback; +} + +inline void i2c_async_err(void) { + i2c_state = I2C_STATE_IDLE; + i2c_regs->ctrl &= ~I2C_CTRL_IE; + printf("I2C error\n"); +//TODO: set an error flag instead of just dropping things on the floor + i2c_regs->cmd_status = I2C_CMD_STOP; +} + +bool i2c_async_read(uint8_t addr, unsigned int len) { + //printf("Starting async read\n"); + if(i2c_state != I2C_STATE_IDLE) return false; //sorry mario but your i2c is in another castle + if(len == 0) return true; //just idiot-proofing + if(len > sizeof(i2c_buf)) return false; + + //disable I2C interrupts and clear pending interrupts on the I2C device + i2c_regs->ctrl &= ~I2C_CTRL_IE; + i2c_regs->cmd_status |= I2C_CMD_IACK; + + i2c_len = len; + i2c_dir = I2C_DIR_READ; + i2c_bufptr = i2c_buf; + //then set up the transfer by issuing the control byte + i2c_regs->ctrl |= I2C_CTRL_IE; + i2c_regs->data = (addr << 1) | 0x01; //7 bit addr and read bit + i2c_regs->cmd_status = I2C_CMD_WR | I2C_CMD_START; //generate start & start writing addr + //update the state so the irq handler knows what's going on + i2c_state = I2C_STATE_CONTROL_BYTE_SENT; + return true; +} + +bool i2c_async_write(uint8_t addr, const uint8_t *buf, unsigned int len) { + //printf("Starting async write\n"); + if(i2c_state != I2C_STATE_IDLE) return false; //sorry mario but your i2c is in another castle + if(len > sizeof(i2c_buf)) return false; + + //disable I2C interrupts and clear pending interrupts on the I2C device + i2c_regs->ctrl &= ~I2C_CTRL_IE; + i2c_regs->cmd_status |= I2C_CMD_IACK; + + //copy the buffer into our own if writing + memcpy((void *)i2c_buf, buf, len); + + i2c_len = len; + i2c_dir = I2C_DIR_WRITE; + i2c_bufptr = i2c_buf; + //then set up the transfer by issuing the control byte + i2c_regs->ctrl |= I2C_CTRL_IE; + i2c_regs->data = (addr << 1) | 0x00; //7 bit addr and read bit + i2c_regs->cmd_status = I2C_CMD_WR | I2C_CMD_START; //generate start & start writing addr + //update the state so the irq handler knows what's going on + i2c_state = I2C_STATE_CONTROL_BYTE_SENT; + + return true; +} + +//TODO: determine if it's better to read sequentially into the user's buffer, copy on transfer complete, or copy on request (shown below). probably best to copy on request. +bool i2c_async_data_ready(void *buf) { + if(i2c_state == I2C_STATE_DATA_READY) { + i2c_state = I2C_STATE_IDLE; + memcpy(buf, (void *)i2c_buf, (i2c_bufptr - i2c_buf)); //TODO: not really comfortable with this + //printf("Copying %d bytes to user buffer\n", i2c_bufptr-i2c_buf); + return true; + } + return false; +} + diff --git a/firmware/microblaze/lib/i2c_async.h b/firmware/microblaze/lib/i2c_async.h new file mode 100644 index 000000000..e6095fca6 --- /dev/null +++ b/firmware/microblaze/lib/i2c_async.h @@ -0,0 +1,50 @@ +// +// Copyright 2010 Ettus Research LLC +// +/* + * Copyright 2007,2008 Free Software Foundation, Inc. + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef INCLUDED_I2C_ASYNC_H +#define INCLUDED_I2C_ASYNC_H + +#include <stdbool.h> +#include "stdint.h" + +typedef enum { I2C_STATE_IDLE, + I2C_STATE_CONTROL_BYTE_SENT, + I2C_STATE_DATA, + I2C_STATE_LAST_BYTE, + I2C_STATE_DATA_READY, + I2C_STATE_ERROR + } i2c_state_t; + +typedef enum { I2C_DIR_WRITE=0, I2C_DIR_READ=1 } i2c_dir_t; + +bool i2c_async_read(uint8_t addr, unsigned int len); +bool i2c_async_write(uint8_t addr, const uint8_t *buf, unsigned int len); +bool i2c_async_data_ready(void *); +//static void i2c_irq_handler(unsigned irq); +void i2c_register_callback(void (*callback)(void)); +void i2c_register_handler(void); + +// Write 24LC024 / 24LC025 EEPROM on motherboard or daughterboard. +// Which EEPROM is determined by i2c_addr. See i2c_addr.h + +bool eeprom_write_async (int i2c_addr, int eeprom_offset, const void *buf, int len, void (*callback)(void)); +bool eeprom_read_async(int i2c_addr, int eeprom_offset, void *buf, int len, void (*callback)(void)); + +#endif /* INCLUDED_I2C_ASYNC_H */ diff --git a/firmware/microblaze/lib/ihex.c b/firmware/microblaze/lib/ihex.c new file mode 100644 index 000000000..97ecf73b6 --- /dev/null +++ b/firmware/microblaze/lib/ihex.c @@ -0,0 +1,57 @@ +/* -*- c++ -*- */ +/* + * Copyright 2010 Ettus Research LLC + * + */ + +#include "ihex.h" +#include <ctype.h> //man that pulls in a lot of shit + +//this is not safe and you should run isxdigit beforehand +uint8_t asc2nibble(char input) { + if(input > 'Z') return input - 'W'; + else if(input > '9') return input - '7'; + else return input - '0'; +} + +int ihex_parse(char input[], ihex_record_t *record) { + //given a NULL-TERMINATED input string (use gets()) in I16HEX format, write the binary record in record. return 0 on success. + + uint8_t inputlen; + uint8_t t, i, checksum_calc=0, checksum_read; + + //first check for ":" leading character + if(input[0] != ':') return -1; + + //then check the string for only valid ASCII ['0'-'F'] + inputlen=1; + while(input[inputlen]) { + if( !isxdigit(input[inputlen++]) ) return -2; + } + + //then read the length. + record->length = (asc2nibble(input[1]) << 4) + asc2nibble(input[2]); + if(input[(record->length<<1) + 11] != 0) return -3; //if we're missing a null terminator in the right place + + //then read the address. + record->addr = (asc2nibble(input[3]) << 12) + (asc2nibble(input[4]) << 8) + (asc2nibble(input[5]) << 4) + asc2nibble(input[6]); + + //then read the record type. + record->type = (asc2nibble(input[7]) << 4) + asc2nibble(input[8]); +// if(record->type > 4) return -4; + + //then read the data, which goes from input[9] to input[9+length*2]. + for(i=0; i < record->length; i++) { + t = 9 + (i<<1); + record->data[i] = (asc2nibble(input[t]) << 4) + (asc2nibble(input[t + 1])); + checksum_calc += record->data[i]; //might as well keep a running checksum as we read + } + checksum_calc += record->length + record->type + (record->addr >> 8) + (record->addr & 0xFF); //get the rest of the data into that checksum + checksum_calc = ~checksum_calc + 1; //checksum is 2's complement + + //now read the checksum of the record + checksum_read = (asc2nibble(input[9 + (record->length<<1)]) << 4) + asc2nibble(input[10 + (record->length<<1)]); + if(checksum_calc != checksum_read) return -5; //compare 'em + + return 0; +} diff --git a/firmware/microblaze/lib/ihex.h b/firmware/microblaze/lib/ihex.h new file mode 100644 index 000000000..9f471fbe2 --- /dev/null +++ b/firmware/microblaze/lib/ihex.h @@ -0,0 +1,18 @@ +/* -*- c++ -*- */ +/* + * Copyright 2010 Ettus Research LLC + * + */ + +#include <stdint.h> +#include <stddef.h> + +typedef struct { + uint8_t type; + size_t length; + uint32_t addr; + uint8_t *data; +} ihex_record_t; + + +int ihex_parse(char input[], ihex_record_t *record); diff --git a/firmware/microblaze/lib/u2_init.c b/firmware/microblaze/lib/u2_init.c index 8d666b76b..099aafe83 100644 --- a/firmware/microblaze/lib/u2_init.c +++ b/firmware/microblaze/lib/u2_init.c @@ -23,6 +23,7 @@ #include "buffer_pool.h" #include "hal_uart.h" #include "i2c.h" +#include "i2c_async.h" #include "mdelay.h" #include "clocks.h" #include "usrp2/fw_common.h" @@ -59,6 +60,7 @@ u2_init(void) // init i2c so we can read our rev pic_init(); // progammable interrupt controller i2c_init(); + i2c_register_handler(); //for using async I2C hal_enable_ints(); get_hw_rev(); diff --git a/firmware/microblaze/lib/udp_fw_update.h b/firmware/microblaze/lib/udp_fw_update.h new file mode 100644 index 000000000..d25525bd2 --- /dev/null +++ b/firmware/microblaze/lib/udp_fw_update.h @@ -0,0 +1,71 @@ +/* -*- c++ -*- */ +/* + * Copyright 2010 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "net_common.h" + +#define USRP2_UDP_UPDATE_PORT 49154 + +typedef enum { + USRP2_FW_UPDATE_ID_WAT = ' ', + + USRP2_FW_UPDATE_ID_OHAI_LOL = 'a', + USRP2_FW_UPDATE_ID_OHAI_OMG = 'A', + + USRP2_FW_UPDATE_ID_WATS_TEH_FLASH_INFO_LOL = 'f', + USRP2_FW_UPDATE_ID_HERES_TEH_FLASH_INFO_OMG = 'F', + + USRP2_FW_UPDATE_ID_ERASE_TEH_FLASHES_LOL = 'e', + USRP2_FW_UPDATE_ID_ERASING_TEH_FLASHES_OMG = 'E', + + USRP2_FW_UPDATE_ID_R_U_DONE_ERASING_LOL = 'd', + USRP2_FW_UPDATE_ID_IM_DONE_ERASING_OMG = 'D', + USRP2_FW_UPDATE_ID_NOPE_NOT_DONE_ERASING_OMG = 'B', + + USRP2_FW_UPDATE_ID_WRITE_TEH_FLASHES_LOL = 'w', + USRP2_FW_UPDATE_ID_WROTE_TEH_FLASHES_OMG = 'W', + + USRP2_FW_UPDATE_ID_READ_TEH_FLASHES_LOL = 'r', + USRP2_FW_UPDATE_ID_KK_READ_TEH_FLASHES_OMG = 'R', + + USRP2_FW_UPDATE_ID_RESET_MAH_COMPUTORZ_LOL = 's', + USRP2_FW_UPDATE_ID_RESETTIN_TEH_COMPUTORZ_OMG = 'S', + + USRP2_FW_UPDATE_ID_KTHXBAI = '~' + +} usrp2_fw_update_id_t; + +typedef struct { + uint32_t proto_ver; + uint32_t id; + uint32_t seq; + union { + uint32_t ip_addr; + struct { + uint32_t flash_addr; + uint32_t length; + uint8_t data[256]; + } flash_args; + struct { + uint32_t sector_size_bytes; + uint32_t memory_size_bytes; + } flash_info_args; + } data; +} usrp2_fw_update_data_t; + +void handle_udp_fw_update_packet(struct socket_address src, struct socket_address dst, + unsigned char *payload, int payload_len); diff --git a/firmware/microblaze/usrp2/Makefile.am b/firmware/microblaze/usrp2/Makefile.am index 8da013980..17f7a4744 100644 --- a/firmware/microblaze/usrp2/Makefile.am +++ b/firmware/microblaze/usrp2/Makefile.am @@ -34,7 +34,8 @@ noinst_LIBRARIES = libusrp2.a libusrp2_a_SOURCES = \ $(COMMON_SRCS) \ sd.c \ - ethernet.c + ethernet.c \ + udp_fw_update.c noinst_PROGRAMS = \ usrp2_txrx_uhd.elf diff --git a/firmware/microblaze/usrp2/udp_fw_update.c b/firmware/microblaze/usrp2/udp_fw_update.c new file mode 100644 index 000000000..14eb0b1ee --- /dev/null +++ b/firmware/microblaze/usrp2/udp_fw_update.c @@ -0,0 +1,34 @@ +/* -*- c++ -*- */ +/* + * Copyright 2010 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +//Routines to handle updating the SPI Flash firmware via UDP + +#include "net_common.h" +#include "usrp2/fw_common.h" +#include <nonstdio.h> +#include "udp_fw_update.h" + +//Firmware update packet handler +void handle_udp_fw_update_packet(struct socket_address src, struct socket_address dst, + unsigned char *payload, int payload_len) { + + usrp2_fw_update_data_t update_data_out; + update_data_out.id = USRP2_FW_UPDATE_ID_WAT; + + send_udp_pkt(USRP2_UDP_UPDATE_PORT, src, &update_data_out, sizeof(update_data_out)); +} diff --git a/firmware/microblaze/usrp2p/.gitignore b/firmware/microblaze/usrp2p/.gitignore new file mode 100644 index 000000000..18f715618 --- /dev/null +++ b/firmware/microblaze/usrp2p/.gitignore @@ -0,0 +1,9 @@ +/Makefile +/Makefile.in +/*.a +/*.bin +/*.dump +/*.ihx +/*.elf +/*.rom +/*.map diff --git a/firmware/microblaze/usrp2p/Makefile.am b/firmware/microblaze/usrp2p/Makefile.am new file mode 100644 index 000000000..0d0b60437 --- /dev/null +++ b/firmware/microblaze/usrp2p/Makefile.am @@ -0,0 +1,69 @@ +# +# Copyright 2010 Ettus Research LLC +# +# This program is free software: you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation, either version 3 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. +# + +include $(top_srcdir)/Makefile.common + +AM_CFLAGS = \ + $(COMMON_CFLAGS) + +AM_LDFLAGS = \ + $(COMMON_LFLAGS) \ + libusrp2p.a \ + -Wl,-defsym -Wl,_TEXT_START_ADDR=0x8050 \ + -Wl,-defsym -Wl,_STACK_SIZE=3072 + +#all of this here is to relocate the hardware vectors to somewhere normal. +RELOCATE_ARGS = \ + --change-section-address .vectors.sw_exception+0x8000 \ + --change-section-address .vectors.hw_exception+0x8000 \ + --change-section-address .vectors.interrupt+0x8000 \ + --change-section-address .vectors.reset+0x8000 + +# $(MB_OBJCOPY) -O ihex $< $@ +# the below would work if objcopy weren't written by apes +# $(MB_OBJCOPY) -O ihex -w --change-section-address .vectors*+0x8000 $< $@ +# using the below will throw away the interrupt vectors when they get relocated below 0x0000. +# $(MB_OBJCOPY) -O ihex --change-addresses -0x8000 $< $@ + +######################################################################## +# USRP2P specific library and programs +######################################################################## +noinst_LIBRARIES = libusrp2p.a + +libusrp2p_a_SOURCES = \ + $(COMMON_SRCS) \ + spif.c \ + spi_flash.c \ + spi_flash_read.c \ + bootloader_utils.c \ + ethernet.c \ + xilinx_s3_icap.c \ + udp_fw_update.c + +noinst_PROGRAMS = \ + usrp2p_txrx_uhd.elf \ + usrp2p_blinkenlights.elf \ + usrp2p_uart_flash_loader.elf + +usrp2p_txrx_uhd_elf_SOURCES = \ + $(top_srcdir)/apps/txrx_uhd.c + +usrp2p_blinkenlights_elf_SOURCES = \ + $(top_srcdir)/apps/blinkenlights.c + +usrp2p_uart_flash_loader_elf_SOURCES = \ + $(top_srcdir)/apps/uart_flash_loader.c diff --git a/firmware/microblaze/usrp2p/bootconfig.h b/firmware/microblaze/usrp2p/bootconfig.h new file mode 100644 index 000000000..35c2726ed --- /dev/null +++ b/firmware/microblaze/usrp2p/bootconfig.h @@ -0,0 +1,61 @@ +/* -*- c -*- */ +/* + * Copyright 2009 Ettus Research LLC + * + * This file is part of GNU Radio + * + * GNU Radio is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 3, or (at your option) + * any later version. + * + * GNU Radio is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. + */ + +#ifndef INCLUDED_BOOTCONFIG_H +#define INCLUDED_BOOTCONFIG_H + +#include <stdbool.h> + +typedef struct { + unsigned char fpga_image_number; + unsigned char firmware_image_number; +} bootconfig_t; + +static inline bootconfig_t +make_bootconfig(unsigned char fpga_image_number, unsigned char firmware_image_number) +{ + bootconfig_t r; + r.fpga_image_number = fpga_image_number; + r.firmware_image_number = firmware_image_number; + return r; +} + +void bootconfig_init(void); /* One time call to initialize */ + +/*! + * \return default boot configuration + */ +bootconfig_t bootconfig_get_default(void); + +/*! + * \brief Set the default boot configuration. + */ +bool bootconfig_set_default(bootconfig_t bc); + +/*! + * \brief attempt to boot the given fpga and software image. + * + * If successful, this routine does not return. + * If it fail for some reason, it returns. + */ +void bootconfig_boot(bootconfig_t bc); + +#endif /* INCLUDED_BOOTCONFIG_H */ diff --git a/firmware/microblaze/usrp2p/bootloader/.gitignore b/firmware/microblaze/usrp2p/bootloader/.gitignore new file mode 100644 index 000000000..17b0f82f3 --- /dev/null +++ b/firmware/microblaze/usrp2p/bootloader/.gitignore @@ -0,0 +1,11 @@ +/*.ihx +/*.rmi +/*_rom +/*.elf +/*.bin +/*.dump +/*.log +/*.rom +/*.map +/Makefile +/Makefile.in diff --git a/firmware/microblaze/usrp2p/bootloader/Makefile.am b/firmware/microblaze/usrp2p/bootloader/Makefile.am new file mode 100644 index 000000000..1fc5daf9c --- /dev/null +++ b/firmware/microblaze/usrp2p/bootloader/Makefile.am @@ -0,0 +1,39 @@ +# +# Copyright 2007,2008,2009 Free Software Foundation, Inc. +# +# This program is free software: you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation, either version 3 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. +# + +include $(top_srcdir)/Makefile.common + +ROM_LINKER_SCRIPT = u2p2-rom.ld + +# loads into 8K boot ram located at 0x0000_0000 +AM_CFLAGS = $(COMMON_CFLAGS) -I$(top_srcdir)/usrp2p +AM_LDFLAGS = -Wl,-T,$(ROM_LINKER_SCRIPT) $(COMMON_LFLAGS) -Wl,-defsym -Wl,_STACK_SIZE=1024 + +EXTRA_DIST = $(ROM_LINKER_SCRIPT) + +LDADD = $(top_srcdir)/usrp2p/libusrp2p.a + +noinst_PROGRAMS = \ + init_bootloader.elf + +init_bootloader_elf_SOURCES = init_bootloader.c + +.bin.rmi: + $(top_srcdir)/bin/bin_to_ram_macro_init.py $< $@ + +_generated_from_elf += \ + $(noinst_PROGRAMS:.elf=.rmi) diff --git a/firmware/microblaze/usrp2p/bootloader/fpga_bootloader.c b/firmware/microblaze/usrp2p/bootloader/fpga_bootloader.c new file mode 100644 index 000000000..9feff6ecd --- /dev/null +++ b/firmware/microblaze/usrp2p/bootloader/fpga_bootloader.c @@ -0,0 +1,202 @@ +/* -*- c -*- */ +/* + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +/* + * This code is bootloader f/w for the slot 0 fpga image. It's job is + * to figure out which fpga image should be loaded, and then to load + * that image from the SPI flash. (FIXME handle retries, errors, + * etc.) + * + * If the center button is down during boot, it loads firwmare + * from 0:0 instead of its normal action. + */ + +#include <stdlib.h> +#include <hal_io.h> +#include <nonstdio.h> +#include <mdelay.h> +#include <quadradio/flashdir.h> +#include <xilinx_v5_icap.h> +#include <bootconfig.h> +#include <bootconfig_private.h> +#include <spi_flash.h> +#include <string.h> +#include <bootloader_utils.h> +#include <hal_interrupts.h> + +#define VERBOSE 1 + +#define OUR_FPGA_IMAGE_NUMBER 0 // this code only runs in slot 0 + +void hal_uart_init(void); +void spif_init(void); +void i2c_init(void); +void bootconfig_init(void); + +void pic_interrupt_handler() __attribute__ ((interrupt_handler)); + +void pic_interrupt_handler() +{ + // nop stub +} + +static int +flash_addr_of_fpga_slot(unsigned int fpga_slot) +{ + const struct flashdir *fd = get_flashdir(); + return fd->slot[fpga_slot + fd->fpga_slot0].start << spi_flash_log2_sector_size(); +} + + +/* + * If the first 256 bytes of the image contain the string of bytes, + * ff ff ff ff aa 99 55 66, we consider it a likely bitstream. + */ +static bool +looks_like_a_bitstream(unsigned int fpga_slot) +{ + unsigned char buf[256]; + static const unsigned char pattern[] = { + 0xff, 0xff, 0xff, 0xff, 0xaa, 0x99, 0x55, 0x66 + }; + + // Read the first 256 bytes of the bitstream + spi_flash_read(flash_addr_of_fpga_slot(fpga_slot), sizeof(buf), buf); + + for (int i = 0; i <= sizeof(buf) - sizeof(pattern); i++) + if (memcmp(pattern, &buf[i], sizeof(pattern)) == 0) + return true; + + return false; +} + +static bool +plausible_bootconfig(bootconfig_t bc) +{ + // Are the fields in range? + if (!validate_bootconfig(bc)) + return false; + + if (!looks_like_a_bitstream(map_fpga_image_number_to_fpga_slot(bc.fpga_image_number))) + return false; + + return true; +} + +// Attempt to boot the fpga image specified in next_boot +static void +initial_boot_attempt(eeprom_boot_info_t *ee) +{ + if (ee->next_boot.fpga_image_number == OUR_FPGA_IMAGE_NUMBER){ + load_firmware(); + return; + } + + ee->nattempts = 1; + _bc_write_eeprom_shadow(); + + unsigned int target_slot = + map_fpga_image_number_to_fpga_slot(ee->next_boot.fpga_image_number); + int flash_addr = flash_addr_of_fpga_slot(target_slot); + + putstr("fpga_bootloader: chaining to "); + puthex4(ee->next_boot.fpga_image_number); + putchar(':'); + puthex4(ee->next_boot.firmware_image_number); + newline(); + mdelay(100); + + while (1){ + icap_reload_fpga(flash_addr); + } +} + +int +main(int argc, char **argv) +{ + hal_disable_ints(); // In case we got here via jmp 0x0 + hal_uart_init(); + i2c_init(); + bootconfig_init(); // Must come after i2c_init. + spif_init(); // Needed for get_flashdir. + + sr_leds->leds = 0xAAAA; + + putstr("\n\n>>> fpga_bootloader <<<\n"); + + putstr("\nBOOTSTS "); + int bootsts = icap_read_config_reg(rBOOTSTS); + puthex32_nl(bootsts); + putstr("STAT "); + int stat = icap_read_config_reg(rSTAT); + puthex32_nl(stat); + + bool fallback = + ((bootsts & (BOOTSTS_VALID_0 | BOOTSTS_FALLBACK_0)) + == (BOOTSTS_VALID_0 | BOOTSTS_FALLBACK_0)); + + if (fallback){ + puts("FALLBACK_0 is set"); + // FIXME handle fallback condition. + } + + const struct flashdir *fd = get_flashdir(); + if (fd == 0) + abort(); + + eeprom_boot_info_t *ee = _bc_get_eeprom_shadow(); + + if (VERBOSE){ + putstr("nattempts: "); + puthex8_nl(ee->nattempts); + } + + mdelay(500); // wait for low-pass on switches + putstr("switches: "); puthex32_nl(readback->switches); + + bool center_btn_down = (readback->switches & BTN_CENTER) != 0; + if (center_btn_down){ + putstr("Center button is down!\n"); + // Force boot of image 0:0 + ee->next_boot = make_bootconfig(0, 0); + } + + // if next_boot is valid, try it + if (plausible_bootconfig(ee->next_boot)) + initial_boot_attempt(ee); // no return + + // if default_boot is valid, try it + if (plausible_bootconfig(ee->default_boot)){ + ee->next_boot = ee->default_boot; + initial_boot_attempt(ee); // no return + } + + // If we're here, we're in trouble. Try all of them... + for (int i = 0; i < 4; i++){ + bootconfig_t bc = make_bootconfig(i, 0); + if (plausible_bootconfig(bc)){ + ee->next_boot = bc; + initial_boot_attempt(ee); // no return + } + } + + // FIXME, try to find something we can load + puts("\n!!! Failed to find a valid FPGA bitstream!\n\n"); + + return 0; +} diff --git a/firmware/microblaze/usrp2p/bootloader/fw_bootloader.c b/firmware/microblaze/usrp2p/bootloader/fw_bootloader.c new file mode 100644 index 000000000..a2c32bf8e --- /dev/null +++ b/firmware/microblaze/usrp2p/bootloader/fw_bootloader.c @@ -0,0 +1,50 @@ +/* -*- c -*- */ +/* + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <memory_map.h> +#include <nonstdio.h> +#include <stdlib.h> +#include <bootconfig.h> +#include <bootconfig_private.h> +#include <bootloader_utils.h> +#include <hal_interrupts.h> + + +void hal_uart_init(void); +void spif_init(void); +void i2c_init(void); +void bootconfig_init(void); + +void pic_interrupt_handler() __attribute__ ((interrupt_handler)); + +void pic_interrupt_handler() +{ + // nop stub +} + +int +main(int argc, char **argv) +{ + hal_disable_ints(); // In case we got here via jmp 0x0 + hal_uart_init(); + i2c_init(); + bootconfig_init(); // Must come after i2c_init. + spif_init(); // Needed for get_flashdir. + + load_firmware(); +} diff --git a/firmware/microblaze/usrp2p/bootloader/icap_test.c b/firmware/microblaze/usrp2p/bootloader/icap_test.c new file mode 100644 index 000000000..5feb9d014 --- /dev/null +++ b/firmware/microblaze/usrp2p/bootloader/icap_test.c @@ -0,0 +1,31 @@ +/* -*- c++ -*- */ +/* + * Copyright 2010 Ettus Research LLC + * + */ + +#include <memory_map.h> +#include <hal_io.h> +#include <xilinx_s3_icap.h> +#include <nonstdio.h> + +void delay(uint32_t t) { + while(t-- != 0) asm("NOP"); +} + + +int main(int argc, char *argv[]) { + pic_init(); + hal_uart_init(); + puts("\nStarting delay...\n"); + + output_regs->leds = 0xFF; + delay(4000000); + output_regs->leds = 0x00; + delay(4000000); + + puts("Rebooting FPGA to 0x00000000\n"); + icap_reload_fpga((uint32_t)0x00000000); + + return 0; +} diff --git a/firmware/microblaze/usrp2p/bootloader/init_bootloader.c b/firmware/microblaze/usrp2p/bootloader/init_bootloader.c new file mode 100644 index 000000000..2bbbd405e --- /dev/null +++ b/firmware/microblaze/usrp2p/bootloader/init_bootloader.c @@ -0,0 +1,129 @@ +/* -*- c++ -*- */ +/* + * Copyright 2010 Ettus Research LLC + * + */ + +#include <memory_map.h> +#include <nonstdio.h> +#include <hal_io.h> +#include <xilinx_s3_icap.h> +#include <spi_flash.h> +#include <spi_flash_private.h> +//#include <clocks.h> +#include <ihex.h> +#include <bootloader_utils.h> +#include <string.h> +#include <hal_uart.h> +#include <i2c.h> +#include "usrp2/fw_common.h" + +bool find_safe_booted_flag(void); +void set_safe_booted_flag(bool flag); + +void pic_interrupt_handler() __attribute__ ((interrupt_handler)); + +void pic_interrupt_handler() +{ + // nop stub +} + +bool find_safe_booted_flag(void) { + unsigned char flag_byte; + eeprom_read(USRP2_I2C_ADDR_MBOARD, USRP2_EE_MBOARD_BOOTLOADER_FLAGS, &flag_byte, 1); + return (flag_byte == 0x5E); +} + +void set_safe_booted_flag(bool flag) { + unsigned char flag_byte = flag ? 0x5E : 0xDC; + eeprom_write(USRP2_I2C_ADDR_MBOARD, USRP2_EE_MBOARD_BOOTLOADER_FLAGS, &flag_byte, 1); +} + + +void load_ihex(void) { //simple IHEX parser to load proper records into RAM. loads program when it receives end of record. + char buf[128]; //input data buffer + uint8_t ihx[32]; //ihex data buffer + + ihex_record_t ihex_record; + ihex_record.data = ihx; + + while(1) { + gets(buf); + + if(!ihex_parse(buf, &ihex_record)) { //RAM data record is valid + if(ihex_record.addr >= RAM_BASE) { //it's expecting to see FULLY RELOCATED IHX RECORDS. every address referenced to 0x8000, including vectors. + memcpy((void *) (ihex_record.addr), ihex_record.data, ihex_record.length); + puts("OK"); + } else if(ihex_record.type == 1) { //end of record + puts("OK"); + //load main firmware + start_program(RAM_BASE); + puts("ERROR: main image returned! Back in IHEX load mode."); + } else puts("NOK"); //RAM loads do not support extended segment address records (04) -- upper 16 bits are always "0". + } else puts("NOK"); + } +} + +void delay(uint32_t t) { + while(t-- != 0) asm("NOP"); +} + +int main(int argc, char *argv[]) { + hal_disable_ints(); // In case we got here via jmp 0x0 + output_regs->leds = 0xFF; + delay(500000); + output_regs->leds = 0x00; + hal_uart_init(); + spif_init(); + i2c_init(); //for EEPROM + puts("USRP2+ bootloader\n"); + + bool production_image = find_safe_booted_flag(); + if(production_image) set_safe_booted_flag(0); //we're the production image, so we clear the flag for the next boot + + if(BUTTON_PUSHED) { //see memory_map.h + puts("Starting USRP2+ in safe mode."); + if(is_valid_fw_image(SAFE_FW_IMAGE_LOCATION_ADDR)) { + spi_flash_read(SAFE_FW_IMAGE_LOCATION_ADDR, FW_IMAGE_SIZE_BYTES, (void *)RAM_BASE); + start_program(RAM_BASE); + puts("ERROR: return from main program! This should never happen!"); + icap_reload_fpga(SAFE_FPGA_IMAGE_LOCATION_ADDR); + } else { + puts("ERROR: no safe firmware image available. I am a brick. Feel free to load IHEX to RAM."); + //puts("ERROR: no safe firmware image available. I am a brick."); + load_ihex(); + } + } + + if(!production_image) { + puts("Checking for valid production FPGA image..."); + if(is_valid_fpga_image(PROD_FPGA_IMAGE_LOCATION_ADDR)) { + puts("Valid production FPGA image found. Attempting to boot."); + set_safe_booted_flag(1); + delay(30000); //so serial output can finish + icap_reload_fpga(PROD_FPGA_IMAGE_LOCATION_ADDR); + } + puts("No valid production FPGA image found.\nAttempting to load production firmware..."); + } + if(is_valid_fw_image(PROD_FW_IMAGE_LOCATION_ADDR)) { + puts("Valid production firmware found. Loading..."); + spi_flash_read(PROD_FW_IMAGE_LOCATION_ADDR, FW_IMAGE_SIZE_BYTES, (void *)RAM_BASE); + start_program(RAM_BASE); + puts("ERROR: Return from main program! This should never happen!"); + //if this happens, though, the safest thing to do is reboot the whole FPGA and start over. + icap_reload_fpga(SAFE_FPGA_IMAGE_LOCATION_ADDR); + return 1; + } + puts("No valid production firmware found. Trying safe firmware..."); + if(is_valid_fw_image(SAFE_FW_IMAGE_LOCATION_ADDR)) { + spi_flash_read(SAFE_FW_IMAGE_LOCATION_ADDR, FW_IMAGE_SIZE_BYTES, (void *)RAM_BASE); + start_program(RAM_BASE); + puts("ERROR: return from main program! This should never happen!"); + icap_reload_fpga(SAFE_FPGA_IMAGE_LOCATION_ADDR); + return 1; + } + puts("ERROR: no safe firmware image available. I am a brick. Feel free to load IHEX to RAM."); + load_ihex(); + + return 0; +} diff --git a/firmware/microblaze/usrp2p/bootloader/serial_loader_burner.c b/firmware/microblaze/usrp2p/bootloader/serial_loader_burner.c new file mode 100644 index 000000000..4ac4df454 --- /dev/null +++ b/firmware/microblaze/usrp2p/bootloader/serial_loader_burner.c @@ -0,0 +1,49 @@ +/* -*- c++ -*- */ +/* + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <hal_io.h> +#include <nonstdio.h> +#include <mdelay.h> +#include <gdbstub2.h> + +void hal_uart_init(void); +void spif_init(void); + +void pic_interrupt_handler() __attribute__ ((interrupt_handler)); + +void pic_interrupt_handler() +{ + // nop stub +} + +int +main(int argc, char **argv) +{ + hal_uart_init(); + spif_init(); + + sr_leds->leds = 0; + mdelay(100); + sr_leds->leds = ~0; + mdelay(100); + sr_leds->leds = 0; + + puts("\n\n>>> stage1: serial_loader_burner <<<"); + + gdbstub2_main_loop(); +} diff --git a/firmware/microblaze/usrp2p/bootloader/spi_bootloader.c b/firmware/microblaze/usrp2p/bootloader/spi_bootloader.c new file mode 100644 index 000000000..678e66cf7 --- /dev/null +++ b/firmware/microblaze/usrp2p/bootloader/spi_bootloader.c @@ -0,0 +1,134 @@ +/* -*- c -*- */ +/* + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <hal_io.h> +#include <nonstdio.h> +#include <mdelay.h> +#include <spi_flash.h> +#include <quadradio/flashdir.h> +#include <quadradio/simple_binary_format.h> +#include <stdlib.h> + + +void hal_uart_init(void); +void spif_init(void); + +void pic_interrupt_handler() __attribute__ ((interrupt_handler)); + +void pic_interrupt_handler() +{ + // nop stub +} + +static void +error(int e) +{ + putstr("ERR"); + puthex8(e); + newline(); +} + +static void +load(uint32_t flash_addr, uint32_t ram_addr, uint32_t size) +{ + spi_flash_read(flash_addr, size, (void *) ram_addr); +} + +static bool +load_from_slot(const struct flashdir *fd, int fw_slot) +{ + putstr("Loading f/w image "); + putchar('0' + fw_slot); + putstr("... "); + + if (fw_slot >= fd->fw_nslots){ + error(1); + return false; + } + + int slot = fw_slot + fd->fw_slot0; + if (fd->slot[slot].start == 0 || fd->slot[slot].start == 0xffff + || fd->slot[slot].len == 0 || fd->slot[slot].len == 0xffff){ + error(2); + return false; + } + + uint32_t sbf_base = fd->slot[slot].start << spi_flash_log2_sector_size(); + uint32_t sbf_len = fd->slot[slot].len << spi_flash_log2_sector_size(); + uint32_t sbf_offset = 0; + + struct sbf_header sbf; + spi_flash_read(sbf_base, sizeof(struct sbf_header), &sbf); + if (sbf.magic != SBF_MAGIC || sbf.nsections > SBF_MAX_SECTIONS){ + error(3); + return false; + } + sbf_offset += sizeof(struct sbf_header); + + unsigned int i; + for (i = 0; i < sbf.nsections; i++){ + if (sbf_offset + sbf.sec_desc[i].length > sbf_len){ + error(4); + return false; + } + load(sbf_offset + sbf_base, + sbf.sec_desc[i].target_addr, + sbf.sec_desc[i].length); + sbf_offset += sbf.sec_desc[i].length; + } + putstr("Done!"); + + typedef void (*fptr_t)(void); + (*(fptr_t) sbf.entry)(); // almost certainly no return + + return true; +} + +int +main(int argc, char **argv) +{ + hal_uart_init(); + spif_init(); + + sr_leds->leds = 0; + mdelay(100); + sr_leds->leds = ~0; + mdelay(100); + sr_leds->leds = 0; + + putstr("\n>>> spi_bootloader <<<\n"); + + const struct flashdir *fd = get_flashdir(); + if (fd == 0) + abort(); + + while(1){ + int sw; + int fw_slot; + + sw = readback->switches; + fw_slot = sw & 0x7; + + if (!load_from_slot(fd, fw_slot)){ + if (fw_slot != 0){ + putstr("Falling back to slot 0\n"); + load_from_slot(fd, 0); + } + } + } +} diff --git a/firmware/microblaze/usrp2p/bootloader/u2p2-rom.ld b/firmware/microblaze/usrp2p/bootloader/u2p2-rom.ld new file mode 100644 index 000000000..4c9eaa8e5 --- /dev/null +++ b/firmware/microblaze/usrp2p/bootloader/u2p2-rom.ld @@ -0,0 +1,190 @@ +/* + * Same as default, but with bss and stack moved to top 2K of main ram + * Copied from qr-rom.ld + */ + +/* Default linker script, for normal executables */ +OUTPUT_FORMAT("elf32-microblaze", "", "") +/*SEARCH_DIR("/home/eb/build/Xilinx_EDK_GNU_10.1i/mb/release/lin/mb/microblaze-xilinx-elf/lib");*/ + + +ENTRY(_start) +_TEXT_START_ADDR = DEFINED(_TEXT_START_ADDR) ? _TEXT_START_ADDR : 0x50; +_HEAP_SIZE = DEFINED(_HEAP_SIZE) ? _HEAP_SIZE : 0x0; +_STACK_SIZE = DEFINED(_STACK_SIZE) ? _STACK_SIZE : 0x400; +_BSS_START_ADDR = DEFINED(_BSS_START_ADDR) ? _BSS_START_ADDR : 0xF800; +SECTIONS +{ + .vectors.reset 0x0 : { KEEP (*(.vectors.reset)) } = 0 + .vectors.sw_exception 0x8 : { KEEP (*(.vectors.sw_exception)) } = 0 + .vectors.interrupt 0x10 : { KEEP (*(.vectors.interrupt)) } = 0 + .vectors.debug_sw_break 0x18 : { KEEP (*(.vectors.debug_sw_break)) } = 0 + .vectors.hw_exception 0x20 : { KEEP (*(.vectors.hw_exception)) } = 0 + . = _TEXT_START_ADDR; + _ftext = .; + .text : { + *(.text) + *(.text.*) + *(.gnu.linkonce.t.*) + } + _etext = .; + .init : { KEEP (*(.init)) } =0 + .fini : { KEEP (*(.fini)) } =0 + PROVIDE (__CTOR_LIST__ = .); + PROVIDE (___CTOR_LIST__ = .); + .ctors : + { + /* gcc uses crtbegin.o to find the start of + the constructors, so we make sure it is + first. Because this is a wildcard, it + doesn't matter if the user does not + actually link against crtbegin.o; the + linker won't look for a file to match a + wildcard. The wildcard also means that it + doesn't matter which directory crtbegin.o + is in. */ + KEEP (*crtbegin.o(.ctors)) + /* We don't want to include the .ctor section from + from the crtend.o file until after the sorted ctors. + The .ctor section from the crtend file contains the + end of ctors marker and it must be last */ + KEEP (*(EXCLUDE_FILE (*crtend.o) .ctors)) + KEEP (*(SORT(.ctors.*))) + KEEP (*(.ctors)) + } + PROVIDE (__CTOR_END__ = .); + PROVIDE (___CTOR_END__ = .); + PROVIDE (__DTOR_LIST__ = .); + PROVIDE (___DTOR_LIST__ = .); + .dtors : + { + KEEP (*crtbegin.o(.dtors)) + KEEP (*(EXCLUDE_FILE (*crtend.o) .dtors)) + KEEP (*(SORT(.dtors.*))) + KEEP (*(.dtors)) + } + PROVIDE (__DTOR_END__ = .); + PROVIDE (___DTOR_END__ = .); + . = ALIGN(4); + _frodata = . ; + .rodata : { + *(.rodata) + *(.rodata.*) + *(.gnu.linkonce.r.*) + CONSTRUCTORS; /* Is this needed? */ + } + _erodata = .; + /* Alignments by 8 to ensure that _SDA2_BASE_ on a word boundary */ + /* Note that .sdata2 and .sbss2 must be contiguous */ + . = ALIGN(8); + _ssrw = .; + .sdata2 : { + *(.sdata2) + *(.sdata2.*) + *(.gnu.linkonce.s2.*) + } + . = ALIGN(4); + .sbss2 : { + PROVIDE (__sbss2_start = .); + *(.sbss2) + *(.sbss2.*) + *(.gnu.linkonce.sb2.*) + PROVIDE (__sbss2_end = .); + } + . = ALIGN(8); + _essrw = .; + _ssrw_size = _essrw - _ssrw; + PROVIDE (_SDA2_BASE_ = _ssrw + (_ssrw_size / 2 )); + . = ALIGN(4); + _fdata = .; + .data : { + *(.data) + *(.gnu.linkonce.d.*) + CONSTRUCTORS; /* Is this needed? */ + } + _edata = . ; + /* Added to handle pic code */ + .got : { + *(.got) + } + .got1 : { + *(.got1) + } + .got2 : { + *(.got2) + } + /* Added by Sathya to handle C++ exceptions */ + .eh_frame : { + *(.eh_frame) + } + .jcr : { + *(.jcr) + } + .gcc_except_table : { + *(.gcc_except_table) + } + /* Alignments by 8 to ensure that _SDA_BASE_ on a word boundary */ + /* Note that .sdata and .sbss must be contiguous */ + . = ALIGN(8); + _ssro = .; + .sdata : { + *(.sdata) + *(.sdata.*) + *(.gnu.linkonce.s.*) + } + . = ALIGN(4); + .sbss : { + PROVIDE (__sbss_start = .); + *(.sbss) + *(.sbss.*) + *(.gnu.linkonce.sb.*) + PROVIDE (__sbss_end = .); + } + . = ALIGN(8); + _essro = .; + _ssro_size = _essro - _ssro; + PROVIDE (_SDA_BASE_ = _ssro + (_ssro_size / 2 )); + . = _BSS_START_ADDR; + . = ALIGN(4); + _fbss = .; + .bss : { + PROVIDE (__bss_start = .); + *(.bss) + *(.bss.*) + *(.gnu.linkonce.b.*) + *(COMMON) + . = ALIGN(4); + PROVIDE (__bss_end = .); + } + . = ALIGN(4); + .heap : { + _heap = .; + _heap_start = .; + . += _HEAP_SIZE; + _heap_end = .; + } + _end = .; + . = ALIGN(4); + . = 0xFFF0; + .stack : { + /* + _stack_end = .; + . += _STACK_SIZE; + . = ALIGN(8); + _stack = .; + _end = .; + */ + _stack_end = .; + _stack = .; + } + .tdata : { + *(.tdata) + *(.tdata.*) + *(.gnu.linkonce.td.*) + } + .tbss : { + *(.tbss) + *(.tbss.*) + *(.gnu.linkonce.tb.*) + } +} diff --git a/firmware/microblaze/usrp2p/bootloader_utils.c b/firmware/microblaze/usrp2p/bootloader_utils.c new file mode 100644 index 000000000..fadd225bb --- /dev/null +++ b/firmware/microblaze/usrp2p/bootloader_utils.c @@ -0,0 +1,39 @@ +/* -*- c++ -*- */ +/* + * Copyright 2010 Ettus Research LLC + * + */ + +//contains routines for loading programs from Flash. depends on Flash libraries. +//also contains routines for reading / writing EEPROM flags for the bootloader +#include <stdbool.h> +#include <string.h> +#include <bootloader_utils.h> +#include <spi_flash.h> + +int is_valid_fpga_image(uint32_t addr) { + uint8_t imgbuf[64]; + spi_flash_read(addr, 64, imgbuf); + //we're just looking for leading 0xFF padding, followed by the sync bytes 0xAA 0x99 + int i = 0; + for(i; i<63; i++) { + if(imgbuf[i] == 0xFF) continue; + if(imgbuf[i] == 0xAA && imgbuf[i+1] == 0x99) return 1; + } + + return 0; +} + +int is_valid_fw_image(uint32_t addr) { + static const uint8_t fwheader[] = {0xB0, 0x00, 0x00, 0x00, 0xB8, 0x08}; //just lookin for a jump to anywhere located at the reset vector + uint8_t buf[12]; + spi_flash_read(addr, 6, buf); + return memcmp(buf, fwheader, 6) == 0; +} + +void start_program(uint32_t addr) +{ + memcpy(0x00000000, addr+0x00000000, 36); //copy the whole vector table, with the reset vector, into boot RAM + typedef void (*fptr_t)(void); + (*(fptr_t) 0x00000000)(); // most likely no return +} diff --git a/firmware/microblaze/usrp2p/bootloader_utils.h b/firmware/microblaze/usrp2p/bootloader_utils.h new file mode 100644 index 000000000..f597c0113 --- /dev/null +++ b/firmware/microblaze/usrp2p/bootloader_utils.h @@ -0,0 +1,22 @@ +/* -*- c++ -*- */ +/* + * Copyright 2010 Ettus Research LLC + * + */ + +#include <stdint.h> + +//we're working in bytes and byte addresses so we can run the same code with Flash chips of different sector sizes. +//it's really 1463736, but rounded up to 1.5MB +#define FPGA_IMAGE_SIZE_BYTES 1572864 +//instead of 32K, we write 31K because we're using the top 1K for stack space! +#define FW_IMAGE_SIZE_BYTES 31744 + +#define SAFE_FPGA_IMAGE_LOCATION_ADDR 0x00000000 +#define SAFE_FW_IMAGE_LOCATION_ADDR 0x003F0000 +#define PROD_FPGA_IMAGE_LOCATION_ADDR 0x00180000 +#define PROD_FW_IMAGE_LOCATION_ADDR 0x00300000 + +int is_valid_fpga_image(uint32_t addr); +int is_valid_fw_image(uint32_t addr); +void start_program(uint32_t addr); diff --git a/firmware/microblaze/usrp2p/eth_phy.h b/firmware/microblaze/usrp2p/eth_phy.h new file mode 100644 index 000000000..d233e96e8 --- /dev/null +++ b/firmware/microblaze/usrp2p/eth_phy.h @@ -0,0 +1,235 @@ +/* -*- c -*- */ +/* + * Copyright 2007 Free Software Foundation, Inc. + * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved. + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +/* Much of this was extracted from the Linux e1000_hw.h file */ + +#ifndef INCLUDED_ETH_PHY_H +#define INCLUDED_ETH_PHY_H + +/* PHY 1000 MII Register/Bit Definitions */ +/* PHY Registers defined by IEEE */ + +#define PHY_CTRL 0x00 /* Control Register */ +#define PHY_STATUS 0x01 /* Status Regiser */ +#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */ +#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */ +#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */ +#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */ +#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */ +#define PHY_NEXT_PAGE_TX 0x07 /* Next Page TX */ +#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */ +#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */ +#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */ +#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */ + +/* PHY 1000 MII Register additions in ET1011C */ +#define PHY_INT_MASK 24 +#define PHY_INT_STATUS 25 +#define PHY_PHY_STATUS 26 +#define PHY_LED2 28 + +/* Bit definitions for some of the registers above */ + +/* PHY Control Register (PHY_CTRL) */ +#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */ +#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */ +#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */ +#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */ +#define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */ +#define MII_CR_POWER_DOWN 0x0800 /* Power down */ +#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */ +#define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */ +#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */ +#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */ + +/* PHY Status Register (PHY_STATUS) */ +#define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */ +#define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */ +#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */ +#define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */ +#define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */ +#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */ +#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */ +#define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */ +#define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */ +#define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */ +#define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */ +#define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */ +#define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */ +#define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */ +#define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */ + +/* Autoneg Advertisement Register (PHY_AUTONEG_ADV) */ +#define NWAY_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */ +#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */ +#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */ +#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */ +#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */ +#define NWAY_AR_100T4_CAPS 0x0200 /* 100T4 Capable */ +#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */ +#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */ +#define NWAY_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */ +#define NWAY_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */ + +/* Link Partner Ability Register (Base Page) (PHY_LP_ABILITY) */ +#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */ +#define NWAY_LPAR_10T_HD_CAPS 0x0020 /* LP is 10T Half Duplex Capable */ +#define NWAY_LPAR_10T_FD_CAPS 0x0040 /* LP is 10T Full Duplex Capable */ +#define NWAY_LPAR_100TX_HD_CAPS 0x0080 /* LP is 100TX Half Duplex Capable */ +#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP is 100TX Full Duplex Capable */ +#define NWAY_LPAR_100T4_CAPS 0x0200 /* LP is 100T4 Capable */ +#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */ +#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */ +#define NWAY_LPAR_REMOTE_FAULT 0x2000 /* LP has detected Remote Fault */ +#define NWAY_LPAR_ACKNOWLEDGE 0x4000 /* LP has rx'd link code word */ +#define NWAY_LPAR_NEXT_PAGE 0x8000 /* Next Page ability supported */ + +/* Autoneg Expansion Register (PHY_AUTONEG_EXP) */ +#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */ +#define NWAY_ER_PAGE_RXD 0x0002 /* LP is 10T Half Duplex Capable */ +#define NWAY_ER_NEXT_PAGE_CAPS 0x0004 /* LP is 10T Full Duplex Capable */ +#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */ +#define NWAY_ER_PAR_DETECT_FAULT 0x0010 /* LP is 100TX Full Duplex Capable */ + +/* Next Page TX Register (PHY_NEXT_PAGE_TX) */ +#define NPTX_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */ +#define NPTX_TOGGLE 0x0800 /* Toggles between exchanges + * of different NP + */ +#define NPTX_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg + * 0 = cannot comply with msg + */ +#define NPTX_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */ +#define NPTX_NEXT_PAGE 0x8000 /* 1 = addition NP will follow + * 0 = sending last NP + */ + +/* Link Partner Next Page Register (PHY_LP_NEXT_PAGE) */ +#define LP_RNPR_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */ +#define LP_RNPR_TOGGLE 0x0800 /* Toggles between exchanges + * of different NP + */ +#define LP_RNPR_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg + * 0 = cannot comply with msg + */ +#define LP_RNPR_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */ +#define LP_RNPR_ACKNOWLDGE 0x4000 /* 1 = ACK / 0 = NO ACK */ +#define LP_RNPR_NEXT_PAGE 0x8000 /* 1 = addition NP will follow + * 0 = sending last NP + */ + +/* 1000BASE-T Control Register (PHY_1000T_CTRL) */ +#define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */ +#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */ +#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */ +#define CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port */ + /* 0=DTE device */ +#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */ + /* 0=Configure PHY as Slave */ +#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */ + /* 0=Automatic Master/Slave config */ +#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */ +#define CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */ +#define CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */ +#define CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */ +#define CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */ + +/* 1000BASE-T Status Register (PHY_1000T_STATUS) */ +#define SR_1000T_IDLE_ERROR_CNT 0x00FF /* Num idle errors since last read */ +#define SR_1000T_ASYM_PAUSE_DIR 0x0100 /* LP asymmetric pause direction bit */ +#define SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */ +#define SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */ +#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */ +#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */ +#define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local TX is Master, 0=Slave */ +#define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */ +#define SR_1000T_REMOTE_RX_STATUS_SHIFT 12 +#define SR_1000T_LOCAL_RX_STATUS_SHIFT 13 +#define SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT 5 +#define FFE_IDLE_ERR_COUNT_TIMEOUT_20 20 +#define FFE_IDLE_ERR_COUNT_TIMEOUT_100 100 + +/* Extended Status Register (PHY_EXT_STATUS) */ +#define IEEE_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */ +#define IEEE_ESR_1000T_FD_CAPS 0x2000 /* 1000T FD capable */ +#define IEEE_ESR_1000X_HD_CAPS 0x4000 /* 1000X HD capable */ +#define IEEE_ESR_1000X_FD_CAPS 0x8000 /* 1000X FD capable */ + +#define PHY_TX_POLARITY_MASK 0x0100 /* register 10h bit 8 (polarity bit) */ +#define PHY_TX_NORMAL_POLARITY 0 /* register 10h bit 8 (normal polarity) */ + +#define AUTO_POLARITY_DISABLE 0x0010 /* register 11h bit 4 */ + /* (0=enable, 1=disable) */ + +/* PHY Status Register (PHY_PHY_STATUS) */ +#define PHYSTAT_ASYMMETRIC (1 << 0) +#define PHYSTAT_PAUSE (1 << 1) +#define PHYSTAT_AUTONEG_EN (1 << 2) +#define PHYSTAT_COLLISION (1 << 3) +#define PHYSTAT_RXSTAT (1 << 4) +#define PHYSTAT_TXSTAT (1 << 5) +#define PHYSTAT_LINK (1 << 6) +#define PHYSTAT_DUPLEX (1 << 7) +#define PHYSTAT_SPEED_MASK ((1 << 8) | (1 << 9)) +#define PHYSTAT_SPEED_1000 (1 << 9) +#define PHYSTAT_SPEED_100 (1 << 8) +#define PHYSTAT_SPEED_10 0 +#define PHYSTAT_POLARITY (1 << 10) +#define PHYSTAT_MDIX (1 << 11) +#define PHYSTAT_AUTONEG_STAT (1 << 12) +#define PHYSTAT_STANDBY (1 << 13) + +/* Interrupt status, mask and clear regs (PHY_INT_{STATUS,MASK,CLEAR}) */ +#define PHY_INT_ENABLE (1 << 0) +#define PHY_INT_DOWNSHIFT (1 << 1) +#define PHY_INT_LINK_STATUS_CHANGE (1 << 2) +#define PHY_INT_RX_STATUS_CHANGE (1 << 3) +#define PHY_INT_FIFO_ERROR (1 << 4) +#define PHY_INT_ERR_CTR_FULL (1 << 5) +#define PHY_INT_NEXT_PAGE_RX (1 << 6) +#define PHY_INT_CRC_ERROR (1 << 7) +#define PHY_INT_AUTONEG_STATUS_CHANGE (1 << 8) +#define PHY_INT_MDIO_SYNC_LOST (1 << 9) +#define PHY_INT_TDR_IP_PHONE (1 << 10) + +/* PHY LED status register 2 (used for controlling link LED for activity light) */ +#define PHY_LED_TXRX_LSB 12 +#define PHY_LED_LINK_LSB 8 +#define PHY_LED_100_LSB 4 +#define PHY_LED_1000_LSB 0 + +#define LED_1000 0 +#define LED_100_TX 1 +#define LED_10 2 +#define LED_1000_ON_100_BLINK 3 +#define LED_LINK 4 +#define LED_TX 5 +#define LED_RX 6 +#define LED_ACTIVITY 7 +#define LED_FULLDUPLEX 8 +#define LED_COLLISION 9 +#define LED_LINK_ON_ACTIVITY_BLINK 10 +#define LED_LINK_ON_RX_BLINK 11 +#define LED_FULL_DUPLEX_ON_COLLISION_BLINK 12 +#define LED_BLINK 13 +#define LED_ON 14 +#define LED_OFF 15 + + +#endif /* INCLUDED_ETH_PHY_H */ diff --git a/firmware/microblaze/usrp2p/ethernet.c b/firmware/microblaze/usrp2p/ethernet.c new file mode 100644 index 000000000..660f28934 --- /dev/null +++ b/firmware/microblaze/usrp2p/ethernet.c @@ -0,0 +1,399 @@ +/* + * Copyright 2007 Free Software Foundation, Inc. + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +//Changes for USRP2P: status registers different (ethernet.h) + +#include "ethernet.h" +#include "memory_map.h" +#include "eth_phy.h" +#include <eth_mac.h> +#include <eth_mac_regs.h> +#include <pic.h> +#include <hal_io.h> +#include <nonstdio.h> +#include <stdbool.h> +#include <i2c.h> +#include "usrp2/fw_common.h" + +#define VERBOSE 0 + +static ethernet_t ed_state; +static ethernet_link_changed_callback_t ed_callback = 0; + +void +ethernet_register_link_changed_callback(ethernet_link_changed_callback_t new_callback) +{ + ed_callback = new_callback; +} + + +static void +ed_set_mac_speed(int speed) +{ + printf("Speed set to %d\n",speed); + /* + switch(speed){ + case 10: + eth_mac->speed = 1; + break; + case 100: + eth_mac->speed = 2; + break; + case 1000: + eth_mac->speed = 4; + break; + default: + break; + } + */ +} + +static void +ed_link_up(int speed) +{ + // putstr("ed_link_up: "); puthex16_nl(speed); + + ed_set_mac_speed(speed); + + //turn on link LED for USRP2P + hal_set_leds(LED_RJ45, LED_RJ45); + + + if (ed_callback) // fire link changed callback + (*ed_callback)(speed); +} + +static void +ed_link_down(void) +{ + // putstr("ed_link_down\n"); + + //turn off link LED for USRP2P + hal_set_leds(0, LED_RJ45); + + if (ed_callback) // fire link changed callback + (*ed_callback)(0); +} + + +static void +ed_link_speed_change(int speed) +{ + ed_link_down(); + ed_link_up(speed); +} + +static void +print_flow_control(int flow_control) +{ + static const char *flow_control_msg[4] = { + "NONE", "WE_TX", "WE_RX", "SYMMETRIC" + }; + putstr("ethernet flow control: "); + puts(flow_control_msg[flow_control & 0x3]); +} + +static void +check_flow_control_resolution(void) +{ + static const unsigned char table[16] = { + // index = {local_asm, local_pause, partner_asm, partner_pause} + FC_NONE, FC_NONE, FC_NONE, FC_NONE, + FC_NONE, FC_SYMM, FC_NONE, FC_SYMM, + FC_NONE, FC_NONE, FC_NONE, FC_WE_TX, + FC_NONE, FC_SYMM, FC_WE_RX, FC_SYMM + }; + + int us = eth_mac_miim_read(PHY_AUTONEG_ADV); + int lp = eth_mac_miim_read(PHY_LP_ABILITY); + int index = (((us >> 10) & 0x3) << 2) | ((lp >> 10) & 0x3); + ed_state.flow_control = table[index]; + + if (1) + print_flow_control(ed_state.flow_control); +} + +/* + * Read the PHY state register to determine link state and speed + */ +static void +ed_check_phy_state(void) +{ + int phystat = eth_mac_miim_read(PHY_PHY_STATUS); + eth_link_state_t new_state = LS_UNKNOWN; + int new_speed = S_UNKNOWN; + + if (VERBOSE){ + putstr("PHYSTAT: "); + puthex16_nl(phystat); + } + + if (phystat & PHYSTAT_LINK){ // link's up + if (VERBOSE) + puts(" LINK_GOOD"); + + new_state = LS_UP; + switch (phystat & PHYSTAT_SPEED_MASK){ + case PHYSTAT_SPEED_10: + new_speed = 10; + break; + + case PHYSTAT_SPEED_100: + new_speed = 100; + break; + + case PHYSTAT_SPEED_1000: + new_speed = 1000; + break; + + default: + new_speed = S_UNKNOWN; + break; + } + + check_flow_control_resolution(); + } + else { // link's down + if (VERBOSE) + puts(" NOT LINK_GOOD"); + + new_state = LS_DOWN; + new_speed = S_UNKNOWN; + } + + if (new_state != ed_state.link_state){ + ed_state.link_state = new_state; // remember new state + if (new_state == LS_UP) + ed_link_up(new_speed); + else if (new_state == LS_DOWN) + ed_link_down(); + } + else if (new_state == LS_UP && new_speed != ed_state.link_speed){ + ed_state.link_speed = new_speed; // remember new speed + ed_link_speed_change(new_speed); + } +} + +/* + * This is fired when the ethernet PHY state changes + */ +static void +eth_phy_irq_handler(unsigned irq) +{ + ed_check_phy_state(); + eth_mac_miim_read(PHY_INT_STATUS); +// eth_mac_miim_write(PHY_INT_CLEAR, ~0); // clear all ints +} + +void +ethernet_init(void) +{ + eth_mac_init(ethernet_mac_addr()); + + ed_state.link_state = LS_UNKNOWN; + ed_state.link_speed = S_UNKNOWN; + + // initialize MAC registers + // eth_mac->tx_hwmark = 0x1e; + //eth_mac->tx_lwmark = 0x19; + + //eth_mac->crc_chk_en = 1; + //eth_mac->rx_max_length = 2048; + + // configure PAUSE frame stuff + //eth_mac->tx_pause_en = 1; // pay attn to pause frames sent to us + + //eth_mac->pause_quanta_set = 38; // a bit more than 1 max frame 16kb/512 + fudge + //eth_mac->pause_frame_send_en = 1; // enable sending pause frames + + + // setup PHY to interrupt on changes + + unsigned mask = + (PHY_INT_ENABLE //master interrupt enable + | PHY_INT_LINK_STATUS_CHANGE + | PHY_INT_RX_STATUS_CHANGE + ); + + eth_mac_miim_read(PHY_INT_STATUS); //clear interrupts + eth_mac_miim_write(PHY_INT_MASK, mask); // enable the ones we want + + //set the LED behavior to activity instead of link + unsigned led = (LED_ACTIVITY << PHY_LED_LINK_LSB) | (LED_TX << PHY_LED_TXRX_LSB); + eth_mac_miim_write(PHY_LED2, led); + + pic_register_handler(IRQ_PHY, eth_phy_irq_handler); + + // Advertise our flow control configuation. + // + // We and the link partner each specify two bits in the base page + // related to autoconfiguration: NWAY_AR_PAUSE and NWAY_AR_ASM_DIR. + // The bits say what a device is "willing" to do, not what may actually + // happen as a result of the negotiation. There are 4 cases: + // + // PAUSE ASM_DIR + // + // 0 0 I have no flow control capability. + // + // 1 0 I both assert and respond to flow control. + // + // 0 1 I assert flow control, but cannot respond. That is, + // I want to be able to send PAUSE frames, but will ignore any + // you send to me. (This is our configuration.) + // + // 1 1 I can both assert and respond to flow control AND I am willing + // to operate symmetrically OR asymmetrically in EITHER direction. + // (We hope the link partner advertises this, otherwise we don't + // get what we want.) + + int t = eth_mac_miim_read(PHY_AUTONEG_ADV); + t &= ~(NWAY_AR_PAUSE | NWAY_AR_ASM_DIR); + t |= NWAY_AR_ASM_DIR; + + // Say we can't to 10BASE-T or 100BASE-TX, half or full duplex + t &= ~(NWAY_AR_10T_HD_CAPS | NWAY_AR_10T_FD_CAPS | NWAY_AR_100TX_HD_CAPS | NWAY_AR_100TX_FD_CAPS); + + eth_mac_miim_write(PHY_AUTONEG_ADV, t); + int r = eth_mac_miim_read(PHY_AUTONEG_ADV); // DEBUG, read back + if (t != r){ + printf("PHY_AUTONEG_ADV: wrote 0x%x, got 0x%x\n", t, r); + } + + // Restart autonegotation. + // We want to ensure that we're advertising our PAUSE capabilities. + t = eth_mac_miim_read(PHY_CTRL); + eth_mac_miim_write(PHY_CTRL, t | MII_CR_RESTART_AUTO_NEG); +} + +static bool +unprogrammed(const void *t, size_t len) +{ + int i; + uint8_t *p = (uint8_t *)t; + bool all_zeros = true; + bool all_ones = true; + for (i = 0; i < len; i++){ + all_zeros &= p[i] == 0x00; + all_ones &= p[i] == 0xff; + } + return all_ones | all_zeros; +} + +//////////////////// MAC Addr Stuff /////////////////////// + +static int8_t src_mac_addr_initialized = false; +static eth_mac_addr_t src_mac_addr = {{ + 0x00, 0x50, 0xC2, 0x85, 0x3f, 0xff + }}; + +const eth_mac_addr_t * +ethernet_mac_addr(void) +{ + if (!src_mac_addr_initialized){ // fetch from eeprom + src_mac_addr_initialized = true; + + // if we're simulating, don't read the EEPROM model, it's REALLY slow + if (hwconfig_simulation_p()) + return &src_mac_addr; + + eth_mac_addr_t tmp; + bool ok = eeprom_read(USRP2_I2C_ADDR_MBOARD, USRP2_EE_MBOARD_MAC_ADDR, &tmp, sizeof(tmp)); + if (!ok || unprogrammed(&tmp, sizeof(tmp))){ + // use the default + } + else + src_mac_addr = tmp; + } + + return &src_mac_addr; +} + +bool +ethernet_set_mac_addr(const eth_mac_addr_t *t) +{ + bool ok = eeprom_write(USRP2_I2C_ADDR_MBOARD, USRP2_EE_MBOARD_MAC_ADDR, t, sizeof(eth_mac_addr_t)); + if (ok){ + src_mac_addr = *t; + src_mac_addr_initialized = true; + //eth_mac_set_addr(t); //this breaks the link + } + + return ok; +} + +//////////////////// IP Addr Stuff /////////////////////// + +static int8_t src_ip_addr_initialized = false; +static struct ip_addr src_ip_addr = { + (192 << 24 | 168 << 16 | 10 << 8 | 2 << 0) +}; + + +const struct ip_addr *get_ip_addr(void) +{ + if (!src_ip_addr_initialized){ // fetch from eeprom + src_ip_addr_initialized = true; + + // if we're simulating, don't read the EEPROM model, it's REALLY slow + if (hwconfig_simulation_p()) + return &src_ip_addr; + + struct ip_addr tmp; + bool ok = eeprom_read(USRP2_I2C_ADDR_MBOARD, USRP2_EE_MBOARD_IP_ADDR, &tmp, sizeof(tmp)); + if (!ok || unprogrammed(&tmp, sizeof(tmp))){ + // use the default + } + else + src_ip_addr = tmp; + } + + return &src_ip_addr; +} + +bool set_ip_addr(const struct ip_addr *t){ + bool ok = eeprom_write(USRP2_I2C_ADDR_MBOARD, USRP2_EE_MBOARD_IP_ADDR, t, sizeof(struct ip_addr)); + if (ok){ + src_ip_addr = *t; + src_ip_addr_initialized = true; + } + + return ok; +} + +int +ethernet_check_errors(void) +{ + // these registers are reset when read + + int r = 0; + /* + if (eth_mac_read_rmon(0x05) != 0) + r |= RME_RX_CRC; + if (eth_mac_read_rmon(0x06) != 0) + r |= RME_RX_FIFO_FULL; + if (eth_mac_read_rmon(0x07) != 0) + r |= RME_RX_2SHORT_2LONG; + + if (eth_mac_read_rmon(0x25) != 0) + r |= RME_TX_JAM_DROP; + if (eth_mac_read_rmon(0x26) != 0) + r |= RME_TX_FIFO_UNDER; + if (eth_mac_read_rmon(0x27) != 0) + r |= RME_TX_FIFO_OVER; + */ + return r; +} diff --git a/firmware/microblaze/usrp2p/memory_map.h b/firmware/microblaze/usrp2p/memory_map.h new file mode 100644 index 000000000..8d0d0c365 --- /dev/null +++ b/firmware/microblaze/usrp2p/memory_map.h @@ -0,0 +1,843 @@ +/* -*- c -*- */ +/* + * Copyright 2007,2008,2009 Free Software Foundation, Inc. + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +/* Overall Memory Map + * 0000-FFFF 64K RAM space + * + * 0000-1FFF 8K Boot RAM + * 2000-5FFF 16K Buffer pool + * 6000-7FFF 8K Peripherals + * 8000-FFFF 32K Main System RAM + + +From u2plus_core.v: +wb_1master #(.decode_w(8), +.s0_addr(8'b0000_0000),.s0_mask(8'b1110_0000), // 0-8K, Boot RAM +.s1_addr(8'b0100_0000),.s1_mask(8'b1100_0000), // 16K-32K, Buffer Pool +.s2_addr(8'b0011_0000),.s2_mask(8'b1111_1111), // SPI 0x3000 +.s3_addr(8'b0011_0001),.s3_mask(8'b1111_1111), // I2C 0x3100 +.s4_addr(8'b0011_0010),.s4_mask(8'b1111_1111), // GPIO 0x3200 +.s5_addr(8'b0011_0011),.s5_mask(8'b1111_1111), // Readback 0x3300 +.s6_addr(8'b0011_0100),.s6_mask(8'b1111_1111), // Ethernet MAC 0x3400 +.s7_addr(8'b0010_0000),.s7_mask(8'b1111_0000), // 8-12K, Settings Bus (only uses 1K) 0x2000-0x2FFF +.s8_addr(8'b0011_0101),.s8_mask(8'b1111_1111), // PIC 0x3500 +.s9_addr(8'b0011_0110),.s9_mask(8'b1111_1111), // Unused 0x3600 +.sa_addr(8'b0011_0111),.sa_mask(8'b1111_1111), // UART 0x3700 +.sb_addr(8'b0011_1000),.sb_mask(8'b1111_1111), // ATR 0x3800 +.sc_addr(8'b0011_1001),.sc_mask(8'b1111_1111), // Unused 0x3900 +.sd_addr(8'b0011_1010),.sd_mask(8'b1111_1111), // ICAP 0x3A00 +.se_addr(8'b0011_1011),.se_mask(8'b1111_1111), // SPI Flash 0x3B00 +.sf_addr(8'b1000_0000),.sf_mask(8'b1000_0000), // 32-64K, Main RAM 0x8000-0xFFFF + .dw(dw),.aw(aw),.sw(sw)) wb_1master + + */ + + +#ifndef INCLUDED_MEMORY_MAP_H +#define INCLUDED_MEMORY_MAP_H + +#include <stdint.h> + + +#define MASTER_CLK_RATE 100000000 // 100 MHz + + +//////////////////////////////////////////////////////////////// +// +// Memory map for embedded wishbone bus +// +//////////////////////////////////////////////////////////////// + +//////////////////////////////////////////////////////////////// +// Boot RAM, Slave 0 + +#define BOOTRAM_BASE 0x0000 + + +//////////////////////////////////////////////////////////////// +// Buffer Pool RAM, Slave 1 +// +// The buffers themselves are located in Slave 1, Buffer Pool RAM. +// The status registers are in Slave 5, Buffer Pool Status. +// The control register is in Slave 7, Settings Bus. + +#define BUFFER_POOL_RAM_BASE 0x4000 + +#define NBUFFERS 8 +#define BP_NLINES 0x0200 // number of 32-bit lines in a buffer +#define BP_LAST_LINE (BP_NLINES - 1) // last line in a buffer + +#define buffer_pool_ram \ + ((uint32_t *) BUFFER_POOL_RAM_BASE) + +#define buffer_ram(n) (&buffer_pool_ram[(n) * BP_NLINES]) + + +///////////////////////////////////////////////////// +// SPI Core, Slave 2. See core docs for more info +#define SPI_BASE 0x3000 // Base address (16-bit) is base peripheral addr + +typedef struct { + volatile uint32_t txrx0; + volatile uint32_t txrx1; + volatile uint32_t txrx2; + volatile uint32_t txrx3; + volatile uint32_t ctrl; + volatile uint32_t div; + volatile uint32_t ss; +} spi_regs_t; + +#define spi_regs ((spi_regs_t *) SPI_BASE) + + +// Masks for controlling different peripherals +#define SPI_SS_AD9510 1 +#define SPI_SS_AD9777 2 +#define SPI_SS_RX_DAC 4 +#define SPI_SS_RX_ADC 8 +#define SPI_SS_RX_DB 16 +#define SPI_SS_TX_DAC 32 +#define SPI_SS_TX_ADC 64 +#define SPI_SS_TX_DB 128 +#define SPI_SS_ADS62P44 256 + +// Masks for different parts of CTRL reg +#define SPI_CTRL_ASS (1<<13) +#define SPI_CTRL_IE (1<<12) +#define SPI_CTRL_LSB (1<<11) +#define SPI_CTRL_TXNEG (1<<10) +#define SPI_CTRL_RXNEG (1<< 9) +#define SPI_CTRL_GO_BSY (1<< 8) +#define SPI_CTRL_CHAR_LEN_MASK 0x7F + +//////////////////////////////////////////////// +// I2C, Slave 3 +// See Wishbone I2C-Master Core Specification. + +#define I2C_BASE 0x3100 + +typedef struct { + volatile uint32_t prescaler_lo; // r/w + volatile uint32_t prescaler_hi; // r/w + volatile uint32_t ctrl; // r/w + volatile uint32_t data; // wr = transmit reg; rd = receive reg + volatile uint32_t cmd_status; // wr = command reg; rd = status reg +} i2c_regs_t; + +#define i2c_regs ((i2c_regs_t *) I2C_BASE) + +#define I2C_CTRL_EN (1 << 7) // core enable +#define I2C_CTRL_IE (1 << 6) // interrupt enable + +// +// STA, STO, RD, WR, and IACK bits are cleared automatically +// +#define I2C_CMD_START (1 << 7) // generate (repeated) start condition +#define I2C_CMD_STOP (1 << 6) // generate stop condition +#define I2C_CMD_RD (1 << 5) // read from slave +#define I2C_CMD_WR (1 << 4) // write to slave +#define I2C_CMD_NACK (1 << 3) // when a rcvr, send ACK (ACK=0) or NACK (ACK=1) +#define I2C_CMD_RSVD_2 (1 << 2) // reserved +#define I2C_CMD_RSVD_1 (1 << 1) // reserved +#define I2C_CMD_IACK (1 << 0) // set to clear pending interrupt + +#define I2C_ST_RXACK (1 << 7) // Received acknowledgement from slave (1 = NAK, 0 = ACK) +#define I2C_ST_BUSY (1 << 6) // 1 after START signal detected; 0 after STOP signal detected +#define I2C_ST_AL (1 << 5) // Arbitration lost. 1 when core lost arbitration +#define I2C_ST_RSVD_4 (1 << 4) // reserved +#define I2C_ST_RSVD_3 (1 << 3) // reserved +#define I2C_ST_RSVD_2 (1 << 2) // reserved +#define I2C_ST_TIP (1 << 1) // Transfer-in-progress +#define I2C_ST_IP (1 << 0) // Interrupt pending + + +//////////////////////////////////////////////// +// GPIO, Slave 4 +// +// These go to the daughterboard i/o pins + +#define GPIO_BASE 0x3200 + +typedef struct { + volatile uint32_t io; // tx data in high 16, rx in low 16 + volatile uint32_t ddr; // 32 bits, 1 means output. tx in high 16, rx in low 16 + volatile uint32_t tx_sel; // 16 2-bit fields select which source goes to TX DB + volatile uint32_t rx_sel; // 16 2-bit fields select which source goes to RX DB +} gpio_regs_t; + +// each 2-bit sel field is layed out this way +#define GPIO_SEL_SW 0 // if pin is an output, set by software in the io reg +#define GPIO_SEL_ATR 1 // if pin is an output, set by ATR logic +#define GPIO_SEL_DEBUG_0 2 // if pin is an output, debug lines from FPGA fabric +#define GPIO_SEL_DEBUG_1 3 // if pin is an output, debug lines from FPGA fabric + +#define gpio_base ((gpio_regs_t *) GPIO_BASE) + +/////////////////////////////////////////////////// +// Buffer Pool Status, Slave 5 +// +// The buffers themselves are located in Slave 1, Buffer Pool RAM. +// The status registers are in Slave 5, Buffer Pool Status. +// The control register is in Slave 7, Settings Bus. + +#define BUFFER_POOL_STATUS_BASE 0x3300 + +typedef struct { + volatile uint32_t last_line[NBUFFERS]; // last line xfer'd in buffer + volatile uint32_t status; // error and done flags + volatile uint32_t hw_config; // see below + volatile uint32_t dummy[3]; + volatile uint32_t irqs; + volatile uint32_t pri_enc_bp_status; + volatile uint32_t cycle_count; +} buffer_pool_status_t; + +#define buffer_pool_status ((buffer_pool_status_t *) BUFFER_POOL_STATUS_BASE) + +#define BUTTON_PUSHED ((buffer_pool_status->irqs & PIC_BUTTON) ? 0 : 1) + +/* + * Buffer n's xfer is done. + * Clear this bit by issuing bp_clear_buf(n) + */ +#define BPS_DONE(n) (0x00000001 << (n)) +#define BPS_DONE_0 BPS_DONE(0) +#define BPS_DONE_1 BPS_DONE(1) +#define BPS_DONE_2 BPS_DONE(2) +#define BPS_DONE_3 BPS_DONE(3) +#define BPS_DONE_4 BPS_DONE(4) +#define BPS_DONE_5 BPS_DONE(5) +#define BPS_DONE_6 BPS_DONE(6) +#define BPS_DONE_7 BPS_DONE(7) + +/* + * Buffer n's xfer had an error. + * Clear this bit by issuing bp_clear_buf(n) + */ +#define BPS_ERROR(n) (0x00000100 << (n)) +#define BPS_ERROR_0 BPS_ERROR(0) +#define BPS_ERROR_1 BPS_ERROR(1) +#define BPS_ERROR_2 BPS_ERROR(2) +#define BPS_ERROR_3 BPS_ERROR(3) +#define BPS_ERROR_4 BPS_ERROR(4) +#define BPS_ERROR_5 BPS_ERROR(5) +#define BPS_ERROR_6 BPS_ERROR(6) +#define BPS_ERROR_7 BPS_ERROR(7) + +/* + * Buffer n is idle. A buffer is idle if it's not + * DONE, ERROR, or processing a transaction. If it's + * IDLE, it's safe to start a new transaction. + * + * Clear this bit by starting a xfer with + * bp_send_from_buf or bp_receive_to_buf. + */ +#define BPS_IDLE(n) (0x00010000 << (n)) +#define BPS_IDLE_0 BPS_IDLE(0) +#define BPS_IDLE_1 BPS_IDLE(1) +#define BPS_IDLE_2 BPS_IDLE(2) +#define BPS_IDLE_3 BPS_IDLE(3) +#define BPS_IDLE_4 BPS_IDLE(4) +#define BPS_IDLE_5 BPS_IDLE(5) +#define BPS_IDLE_6 BPS_IDLE(6) +#define BPS_IDLE_7 BPS_IDLE(7) + +/* + * Buffer n has a "slow path" packet in it. + * This bit is orthogonal to the bits above and indicates that + * the FPGA ethernet rx protocol engine has identified this packet + * as one requiring firmware intervention. + */ +#define BPS_SLOWPATH(n) (0x01000000 << (n)) +#define BPS_SLOWPATH_0 BPS_SLOWPATH(0) +#define BPS_SLOWPATH_1 BPS_SLOWPATH(1) +#define BPS_SLOWPATH_2 BPS_SLOWPATH(2) +#define BPS_SLOWPATH_3 BPS_SLOWPATH(3) +#define BPS_SLOWPATH_4 BPS_SLOWPATH(4) +#define BPS_SLOWPATH_5 BPS_SLOWPATH(5) +#define BPS_SLOWPATH_6 BPS_SLOWPATH(6) +#define BPS_SLOWPATH_7 BPS_SLOWPATH(7) + + +#define BPS_DONE_ALL 0x000000ff // mask of all dones +#define BPS_ERROR_ALL 0x0000ff00 // mask of all errors +#define BPS_IDLE_ALL 0x00ff0000 // mask of all idles +#define BPS_SLOWPATH_ALL 0xff000000 // mask of all slowpaths + +// The hw_config register + +#define HWC_SIMULATION 0x80000000 +#define HWC_WB_CLK_DIV_MASK 0x0000000f + +/*! + * \brief return non-zero if we're running under the simulator + */ +inline static int +hwconfig_simulation_p(void) +{ + return buffer_pool_status->hw_config & HWC_SIMULATION; +} + +/*! + * \brief Return Wishbone Clock divisor. + * The processor runs at the Wishbone Clock rate which is MASTER_CLK_RATE / divisor. + */ +inline static int +hwconfig_wishbone_divisor(void) +{ + return buffer_pool_status->hw_config & HWC_WB_CLK_DIV_MASK; +} + +/////////////////////////////////////////////////// +// Ethernet Core, Slave 6 + +#define ETH_BASE 0x3400 + +#include "eth_mac_regs.h" + +#define eth_mac ((eth_mac_regs_t *) ETH_BASE) + +//////////////////////////////////////////////////// +// Settings Bus, Slave #7, Not Byte Addressable! +// +// Output-only from processor point-of-view. +// 1KB of address space (== 256 32-bit write-only regs) + + +#define MISC_OUTPUT_BASE 0x2000 +#define TX_PROTOCOL_ENGINE_BASE 0x2080 +#define RX_PROTOCOL_ENGINE_BASE 0x20C0 +#define BUFFER_POOL_CTRL_BASE 0x2100 +#define LAST_SETTING_REG 0x23FC // last valid setting register + +#define SR_MISC 0 +#define SR_TX_PROT_ENG 32 +#define SR_RX_PROT_ENG 48 +#define SR_BUFFER_POOL_CTRL 64 +#define SR_UDP_SM 96 +#define SR_TX_DSP 208 +#define SR_TX_CTRL 224 +#define SR_RX_DSP 160 +#define SR_RX_CTRL 176 +#define SR_TIME64 192 +#define SR_SIMTIMER 198 +#define SR_LAST 255 + +#define _SR_ADDR(sr) (MISC_OUTPUT_BASE + (sr) * sizeof(uint32_t)) + +// --- buffer pool control regs --- + +typedef struct { + volatile uint32_t ctrl; +} buffer_pool_ctrl_t; + +// buffer pool ports + +#define PORT_SERDES 0 // serial/deserializer +#define PORT_DSP 1 // DSP tx or rx pipeline +#define PORT_ETH 2 // ethernet tx or rx +#define PORT_RAM 3 // RAM tx or rx + +// the buffer pool ctrl register fields + +#define BPC_BUFFER(n) (((n) & 0xf) << 28) +#define BPC_BUFFER_MASK BPC_BUFFER(~0) +#define BPC_BUFFER_0 BPC_BUFFER(0) +#define BPC_BUFFER_1 BPC_BUFFER(1) +#define BPC_BUFFER_2 BPC_BUFFER(2) +#define BPC_BUFFER_3 BPC_BUFFER(3) +#define BPC_BUFFER_4 BPC_BUFFER(4) +#define BPC_BUFFER_5 BPC_BUFFER(5) +#define BPC_BUFFER_6 BPC_BUFFER(6) +#define BPC_BUFFER_7 BPC_BUFFER(7) +#define BPC_BUFFER_NIL BPC_BUFFER(0x8) // disable + +#define BPC_PORT(n) (((n) & 0x7) << 25) +#define BPC_PORT_MASK BPC_PORT(~0) +#define BPC_PORT_SERDES BPC_PORT(PORT_SERDES) +#define BPC_PORT_DSP BPC_PORT(PORT_DSP) +#define BPC_PORT_ETH BPC_PORT(PORT_ETH) +#define BPC_PORT_RAM BPC_PORT(PORT_RAM) +#define BPC_PORT_NIL BPC_PORT(0x4) // disable + +#define BPC_CLR (1 << 24) // mutually excl commands +#define BPC_READ (1 << 23) +#define BPC_WRITE (1 << 22) + +#define BPC_STEP(step) (((step) & 0xf) << 18) +#define BPC_STEP_MASK BPC_STEP(~0) +#define BPC_LAST_LINE(line) (((line) & 0x1ff) << 9) +#define BPC_LAST_LINE_MASK BPC_LAST_LINE(~0) +#define BPC_FIRST_LINE(line) (((line) & 0x1ff) << 0) +#define BPC_FIRST_LINE_MASK BPC_FIRST_LINE(~0) + +#define buffer_pool_ctrl ((buffer_pool_ctrl_t *) BUFFER_POOL_CTRL_BASE) + +// --- misc outputs --- + +typedef struct { + volatile uint32_t clk_ctrl; + volatile uint32_t serdes_ctrl; + volatile uint32_t adc_ctrl; + volatile uint32_t leds; + volatile uint32_t phy_ctrl; // LSB is reset line to eth phy + volatile uint32_t debug_mux_ctrl; + volatile uint32_t ram_page; // FIXME should go somewhere else... + volatile uint32_t flush_icache; // Flush the icache + volatile uint32_t led_src; // HW or SW control for LEDs +} output_regs_t; + +#define CLK_RESET (1<<4) +#define CLK_ENABLE (1<<3) | (1<<2) +#define CLK_SEL (1<<1) | (1<<0) + +#define SERDES_ENABLE 8 +#define SERDES_PRBSEN 4 +#define SERDES_LOOPEN 2 +#define SERDES_RXEN 1 + +#define ADC_CTRL_ON 0x0F +#define ADC_CTRL_OFF 0x00 + +// crazy order that matches the labels on the case + +#define LED_A (1 << 2) +#define LED_B (1 << 0) +#define LED_E (1 << 3) +#define LED_D (1 << 1) +#define LED_C (1 << 4) +// LED_F // controlled by CPLD +#define LED_RJ45 (1 << 5) + +#define output_regs ((output_regs_t *) MISC_OUTPUT_BASE) + +// --- udp tx regs --- + +typedef struct { + // Bits 19:16 are control info; bits 15:0 are data (see below) + // First two words are unused. + volatile uint32_t _nope[2]; + //--- ethernet header - 14 bytes--- + volatile struct{ + uint32_t mac_dst_0_1; //word 2 + uint32_t mac_dst_2_3; + uint32_t mac_dst_4_5; + uint32_t mac_src_0_1; + uint32_t mac_src_2_3; + uint32_t mac_src_4_5; + uint32_t ether_type; //word 8 + } eth_hdr; + //--- ip header - 20 bytes --- + volatile struct{ + uint32_t ver_ihl_tos; //word 9 + uint32_t total_length; + uint32_t identification; + uint32_t flags_frag_off; + uint32_t ttl_proto; + uint32_t checksum; + uint32_t src_addr_high; + uint32_t src_addr_low; + uint32_t dst_addr_high; + uint32_t dst_addr_low; //word 18 + } ip_hdr; + //--- udp header - 8 bytes --- + volatile struct{ + uint32_t src_port; //word 19 + uint32_t dst_port; + uint32_t length; + uint32_t checksum; //word 22 + } udp_hdr; + volatile uint32_t _pad[32-23]; +} sr_udp_sm_t; + +// control bits (all expect UDP_SM_LAST_WORD are mutually exclusive) + +// This is the last word of the header +#define UDP_SM_LAST_WORD (1 << 19) + +// Insert IP header checksum here. Data is the xor of 16'hFFFF and +// the values written into regs 9-13 and 15-18. +#define UDP_SM_INS_IP_HDR_CHKSUM (1 << 18) + +// Insert IP Length here (data ignored) +#define UDP_SM_INS_IP_LEN (1 << 17) + +// Insert UDP Length here (data ignore) +#define UDP_SM_INS_UDP_LEN (1 << 16) + +#define sr_udp_sm ((sr_udp_sm_t *) _SR_ADDR(SR_UDP_SM)) + +// --- dsp tx regs --- + +#define MIN_CIC_INTERP 1 +#define MAX_CIC_INTERP 128 + +typedef struct { + volatile uint32_t num_chan; + volatile uint32_t clear_state; // clears out state machine, fifos, +} sr_tx_ctrl_t; + +#define sr_tx_ctrl ((sr_tx_ctrl_t *) _SR_ADDR(SR_TX_CTRL)) + +typedef struct { + volatile int32_t freq; + volatile uint32_t scale_iq; // {scale_i,scale_q} + volatile uint32_t interp_rate; + volatile uint32_t _padding0; // padding for the tx_mux + // NOT freq, scale, interp + /*! + * \brief output mux configuration. + * + * <pre> + * 3 2 1 + * 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 + * +-------------------------------+-------+-------+-------+-------+ + * | | DAC1 | DAC0 | + * +-------------------------------+-------+-------+-------+-------+ + * + * There are N DUCs (1 now) with complex inputs and outputs. + * There are two DACs. + * + * Each 4-bit DACx field specifies the source for the DAC + * Each subfield is coded like this: + * + * 3 2 1 0 + * +-------+ + * | N | + * +-------+ + * + * N specifies which DUC output is connected to this DAC. + * + * N which interp output + * --- ------------------- + * 0 DUC 0 I + * 1 DUC 0 Q + * 2 DUC 1 I + * 3 DUC 1 Q + * F All Zeros + * + * The default value is 0x10 + * </pre> + */ + volatile uint32_t tx_mux; + +} dsp_tx_regs_t; + +#define dsp_tx_regs ((dsp_tx_regs_t *) _SR_ADDR(SR_TX_DSP)) + +// --- VITA RX CTRL regs --- +typedef struct { + // The following 3 are logically a single command register. + // They are clocked into the underlying fifo when time_ticks is written. + volatile uint32_t cmd; // {now, chain, num_samples(30) + volatile uint32_t time_secs; + volatile uint32_t time_ticks; + + volatile uint32_t clear_overrun; // write anything to clear overrun + volatile uint32_t vrt_header; // word 0 of packet. FPGA fills in packet counter + volatile uint32_t vrt_stream_id; // word 1 of packet. + volatile uint32_t vrt_trailer; + volatile uint32_t nsamples_per_pkt; + volatile uint32_t nchannels; // 1 in basic case, up to 4 for vector sources + volatile uint32_t pad[7]; // Make each structure 16 elements long +} sr_rx_ctrl_t; + +#define sr_rx_ctrl ((sr_rx_ctrl_t *) _SR_ADDR(SR_RX_CTRL)) + +// --- dsp rx regs --- +#define MIN_CIC_DECIM 1 +#define MAX_CIC_DECIM 128 + +typedef struct { + volatile int32_t freq; + volatile uint32_t scale_iq; // {scale_i,scale_q} + volatile uint32_t decim_rate; + volatile uint32_t dcoffset_i; // Bit 31 high sets fixed offset mode, using lower 14 bits, + // otherwise it is automatic + volatile uint32_t dcoffset_q; // Bit 31 high sets fixed offset mode, using lower 14 bits + + /*! + * \brief input mux configuration. + * + * This determines which ADC (or constant zero) is connected to + * each DDC input. There are N DDCs (1 now). Each has two inputs. + * + * <pre> + * Mux value: + * + * 3 2 1 + * 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 + * +-------+-------+-------+-------+-------+-------+-------+-------+ + * | |Q0 |I0 | + * +-------+-------+-------+-------+-------+-------+-------+-------+ + * + * Each 2-bit I field is either 00 (A/D A), 01 (A/D B) or 1X (const zero) + * Each 2-bit Q field is either 00 (A/D A), 01 (A/D B) or 1X (const zero) + * + * The default value is 0x4 + * </pre> + */ + volatile uint32_t rx_mux; // called adc_mux in dsp_core_rx.v + + /*! + * \brief Streaming GPIO configuration + * + * This determines whether the LSBs of I and Q samples come from the DSP + * pipeline or from the io_rx GPIO pins. To stream GPIO, one must first + * set the GPIO data direction register to have io_rx[15] and/or io_rx[14] + * configured as inputs. The GPIO pins will be sampled at the time the + * remainder of the DSP sample is strobed into the RX sample FIFO. There + * will be a decimation-dependent fixed time offset between the GPIO + * sample stream and the associated RF samples. + * + * 3 2 1 + * 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 + * +-------+-------+-------+-------+-------+-------+-------+-------+ + * | MBZ |Q|I| + * +-------+-------+-------+-------+-------+-------+-------+-------+ + * + * I 0=LSB comes from DSP pipeline (default) + * 1=LSB comes from io_rx[15] + * + * Q 0=LSB comes from DSP pipeline (default) + * 1=LSB comes from io_rx[14] + */ + volatile uint32_t gpio_stream_enable; + +} dsp_rx_regs_t; + +#define dsp_rx_regs ((dsp_rx_regs_t *) _SR_ADDR(SR_RX_DSP)) + +// ---------------------------------------------------------------- +// VITA49 64 bit time (write only) + /*! + * \brief Time 64 flags + * + * <pre> + * + * 3 2 1 + * 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 + * +-----------------------------------------------------------+-+-+ + * | |S|P| + * +-----------------------------------------------------------+-+-+ + * + * P - PPS edge selection (0=negedge, 1=posedge, default=0) + * S - Source (0=sma, 1=mimo, 0=default) + * + * </pre> + */ +typedef struct { + volatile uint32_t secs; // value to set absolute secs to on next PPS + volatile uint32_t ticks; // value to set absolute ticks to on next PPS + volatile uint32_t flags; // flags - see chart above + volatile uint32_t imm; // set immediate (0=latch on next pps, 1=latch immediate, default=0) +} sr_time64_t; + +#define sr_time64 ((sr_time64_t *) _SR_ADDR(SR_TIME64)) + + +/* + * --- ethernet tx protocol engine regs (write only) --- + * + * These registers control the transmit portion of the ethernet + * protocol engine (out of USRP2). The protocol engine handles fifo + * status and sequence number insertion in outgoing packets, and + * automagically generates status packets when required to inform the + * host of changes in fifo availability. + * + * All outgoing packets have their fifo_status field set to the number + * of 32-bit lines of fifo available in the ethernet Rx fifo (see + * usrp2_eth_packet.h). Seqno's are set if FIXME, else 0. + * + * FIXME clean this up once we know how it's supposed to behave. + */ + +typedef struct { + volatile uint32_t flags; // not yet fully defined (channel?) + volatile uint32_t mac_dst0123; // 4 bytes of destination mac addr + volatile uint32_t mac_dst45src01; // 2 bytes of dest mac addr; 2 bytes of src mac addr + volatile uint32_t mac_src2345; // 4 bytes of destination mac addr + volatile uint32_t seqno; // Write to init seqno. It autoincs on match +} tx_proto_engine_regs_t; + +#define tx_proto_engine ((tx_proto_engine_regs_t *) TX_PROTOCOL_ENGINE_BASE) + +/* + * --- ethernet rx protocol engine regs (write only) --- + * + * These registers control the receive portion of the ethernet + * protocol engine (into USRP2). The protocol engine offloads common + * packet inspection operations so that firmware has less to do on + * "fast path" packets. + * + * The registers define conditions which must be matched for a packet + * to be considered a "fast path" packet. If a received packet + * matches the src and dst mac address, ethertype, flags field, and + * expected seqno number it is considered a "fast path" packet, and + * the expected seqno is updated. If the packet fails to satisfy any + * of the above conditions it's a "slow path" packet, and the + * corresponding SLOWPATH flag will be set buffer_status register. + */ + +typedef struct { + volatile uint32_t flags; // not yet fully defined (channel?) + volatile uint32_t mac_dst0123; // 4 bytes of destination mac addr + volatile uint32_t mac_dst45src01; // 2 bytes of dest mac addr; 2 bytes of src mac addr + volatile uint32_t mac_src2345; // 4 bytes of destination mac addr + volatile uint32_t ethertype_pad; // ethertype in high 16-bits +} rx_proto_engine_regs_t; + +#define rx_proto_engine ((rx_proto_engine_regs_t *) RX_PROTOCOL_ENGINE_BASE) + + + +/////////////////////////////////////////////////// +// Simple Programmable Interrupt Controller, Slave 8 + +#define PIC_BASE 0x3500 + +// Interrupt request lines +// Bit numbers (LSB == 0) that correpond to interrupts into PIC + +#define IRQ_BUFFER 0 // buffer manager +#define IRQ_ONETIME 1 +#define IRQ_SPI 2 +#define IRQ_I2C 3 +#define IRQ_PHY 4 // ethernet PHY +#define IRQ_UNDERRUN 5 +#define IRQ_OVERRUN 6 +#define IRQ_PPS 7 // pulse per second +#define IRQ_UART_RX 8 +#define IRQ_UART_TX 9 +#define IRQ_SERDES 10 +#define IRQ_CLKSTATUS 11 +#define IRQ_PERIODIC 12 +#define IRQ_BUTTON 13 + +#define IRQ_TO_MASK(x) (1 << (x)) + +#define PIC_BUFFER_INT IRQ_TO_MASK(IRQ_BUFFER) +#define PIC_ONETIME_INT IRQ_TO_MASK(IRQ_ONETIME) +#define PIC_SPI_INT IRQ_TO_MASK(IRQ_SPI) +#define PIC_I2C_INT IRQ_TO_MASK(IRQ_I2C) +#define PIC_PHY_INT IRQ_TO_MASK(IRQ_PHY) +#define PIC_UNDERRUN_INT IRQ_TO_MASK(IRQ_UNDERRUN) +#define PIC_OVERRUN_INT IRQ_TO_MASK(IRQ_OVERRUN) +#define PIC_PPS_INT IRQ_TO_MASK(IRQ_PPS) +#define PIC_UART_RX_INT IRQ_TO_MASK(IRQ_UART_RX) +#define PIC_UART_TX_INT IRQ_TO_MASK(IRQ_UART_TX) +#define PIC_SERDES IRQ_TO_MASK(IRQ_SERDES) +#define PIC_CLKSTATUS IRQ_TO_MASK(IRQ_CLKSTATUS) +#define PIC_BUTTON IRQ_TO_MASK(IRQ_BUTTON) + +typedef struct { + volatile uint32_t edge_enable; // mask: 1 -> edge triggered, 0 -> level + volatile uint32_t polarity; // mask: 1 -> rising edge + volatile uint32_t mask; // mask: 1 -> disabled + volatile uint32_t pending; // mask: 1 -> pending; write 1's to clear pending ints +} pic_regs_t; + +#define pic_regs ((pic_regs_t *) PIC_BASE) + +// ---------------------------------------------------------------- +// WB_CLK_RATE is the time base for this +typedef struct { + volatile uint32_t onetime; // Number of wb clk cycles till the onetime interrupt + volatile uint32_t periodic; // Repeat rate of periodic interrupt +} sr_simple_timer_t; + +#define sr_simple_timer ((sr_simple_timer_t *) _SR_ADDR(SR_SIMTIMER)) + +/////////////////////////////////////////////////// +// UNUSED, Slave 9 + +/////////////////////////////////////////////////// +// UART, Slave 10 + +#define UART_BASE 0x3700 + +typedef struct { + // All elements are 8 bits except for clkdiv (16), but we use uint32 to make + // the hardware for decoding easier + volatile uint32_t clkdiv; // Set to 50e6 divided by baud rate (no x16 factor) + volatile uint32_t txlevel; // Number of spaces in the FIFO for writes + volatile uint32_t rxlevel; // Number of available elements in the FIFO for reads + volatile uint32_t txchar; // Write characters to be sent here + volatile uint32_t rxchar; // Read received characters here + volatile uint32_t x[3]; //padding to reach 32B +} uart_regs_t; + +#define uart_regs ((uart_regs_t *) UART_BASE) + +/////////////////////////////////////////////////// +// ATR Controller, Slave 11 + +#define ATR_BASE 0x3800 + +typedef struct { + volatile uint32_t v[16]; +} atr_regs_t; + +#define ATR_IDLE 0x0 // indicies into v +#define ATR_TX 0x1 +#define ATR_RX 0x2 +#define ATR_FULL 0x3 + +#define atr_regs ((atr_regs_t *) ATR_BASE) + +/////////////////////////////////////////////////// +// UNUSED, Slave 12 + +/////////////////////////////////////////////////// +// ICAP, Slave 13 + +#define ICAP_BASE 0x3A00 +typedef struct { + uint32_t icap; //only the lower 8 bits matter +} icap_regs_t; + +#define icap_regs ((icap_regs_t *) ICAP_BASE) + +/////////////////////////////////////////////////// +// SPI Flash interface, Slave 14 +// Control register definitions are the same as SPI, so use SPI_CTRL_ASS, etc. +// Peripheral mask not needed since bus is dedicated (CE held low) + +#define SPIF_BASE 0x3B00 +typedef struct { + volatile uint32_t txrx0; + volatile uint32_t txrx1; + volatile uint32_t txrx2; + volatile uint32_t txrx3; + volatile uint32_t ctrl; + volatile uint32_t div; + volatile uint32_t ss; +} spif_regs_t; + +#define spif_regs ((spif_regs_t *) SPIF_BASE) + +//////////////////////////////////////////////////////////////// +// Main RAM, Slave 15 + +#define RAM_BASE 0x8000 + + + +/////////////////////////////////////////////////// +#endif + diff --git a/firmware/microblaze/usrp2p/spi_flash.c b/firmware/microblaze/usrp2p/spi_flash.c new file mode 100644 index 000000000..09b74a513 --- /dev/null +++ b/firmware/microblaze/usrp2p/spi_flash.c @@ -0,0 +1,194 @@ +/* -*- c++ -*- */ +/* + * Copyright 2009 Free Software Foundation, Inc. + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "spi_flash_private.h" +//#include <stdlib.h> +#include <nonstdio.h> + +uint32_t +spi_flash_rdsr(void) +{ + return spif_transact(SPI_TXRX, SPI_SS_FLASH, RDSR_CMD << 8, 16, FLAGS) & 0xff; +} + +static void +spi_flash_write_enable(void) +{ +// spif_transact(SPI_TXONLY, SPI_SS_FLASH, (WRSR_CMD << 8) | 0x00, 16, FLAGS); //disable write protection bits + spif_transact(SPI_TXONLY, SPI_SS_FLASH, WREN_CMD, 8, FLAGS); +} + +bool +spi_flash_done_p(void) +{ + return (spi_flash_rdsr() & SR_WIP) == 0; +} + +void +spi_flash_wait(void) +{ + while (!spi_flash_done_p()) + ; +} + +void +spi_flash_erase_sector_start(uint32_t flash_addr) +{ + //uprintf(UART_DEBUG, "spi_flash_erase_sector_start: addr = 0x%x\n", flash_addr); + + spi_flash_wait(); + spi_flash_write_enable(); + spif_transact(SPI_TXONLY, SPI_SS_FLASH, + (SE_CMD << 24) | (flash_addr & 0x00ffffff), + 32, FLAGS); +} + +bool +spi_flash_page_program_start(uint32_t flash_addr, size_t nbytes, const void *buf) +{ + if (nbytes == 0 || nbytes > SPI_FLASH_PAGE_SIZE) + return false; + + uint32_t local_buf[SPI_FLASH_PAGE_SIZE / sizeof(uint32_t)]; + memset(local_buf, 0xff, sizeof(local_buf)); // init to 0xff (nops when programming) + memcpy(local_buf, buf, nbytes); + + spi_flash_wait(); + spi_flash_write_enable(); + + /* + * We explicitly control the slave select here (/S), so that we can + * do the entire write operation as a single transaction from + * device's point of view. (The most our SPI peripheral can transfer + * in a single shot is 16 bytes.) + */ + spif_wait(); + + spif_regs->ss = 0; + spif_regs->ctrl = FLAGS; // ASS is now clear and no chip select is enabled. + + /* write PP_CMD, ADDR2, ADDR1, ADDR0 */ + + spif_regs->txrx0 = (PP_CMD << 24) | (flash_addr & 0x00ffffff); + spif_regs->ss = SPI_SS_FLASH; // assert chip select + spif_regs->ctrl = FLAGS | LEN(4 * 8); + spif_regs->ctrl = FLAGS | LEN(4 * 8) | SPI_CTRL_GO_BSY; + spif_wait(); + + /* send 256 bytes total, 16 at a time */ + for (size_t i = 0; i < 16; i++){ + spif_regs->txrx3 = local_buf[i * 4 + 0]; + spif_regs->txrx2 = local_buf[i * 4 + 1]; + spif_regs->txrx1 = local_buf[i * 4 + 2]; + spif_regs->txrx0 = local_buf[i * 4 + 3]; + + spif_regs->ctrl = FLAGS | LEN(16 * 8); // xfer 16 bytes + spif_regs->ctrl = FLAGS | LEN(16 * 8) | SPI_CTRL_GO_BSY; + spif_wait(); + } + spif_regs->ss = 0; // desassert chip select + + return true; +} + +void +spi_flash_erase(uint32_t flash_addr, size_t nbytes) +{ + if (nbytes == 0) + return; + + uint32_t first = round_down(flash_addr, spi_flash_sector_size()); + uint32_t last = round_down(flash_addr + nbytes - 1, spi_flash_sector_size()); + + for (uint32_t s = first; s <= last; s += spi_flash_sector_size()){ + spi_flash_erase_sector_start(s); + } + spi_flash_wait(); +} + +bool +spi_flash_program(uint32_t flash_addr, size_t nbytes, const void *buf) +{ + //uprintf(UART_DEBUG, "\nspi_flash_program: addr = 0x%x, nbytes = %d\n", flash_addr, nbytes); + + const unsigned char *p = (const unsigned char *) buf; + size_t n; + + if (nbytes == 0) + return true; + + uint32_t r = flash_addr % SPI_FLASH_PAGE_SIZE; + if (r){ /* do initial non-aligned page */ + n = min(SPI_FLASH_PAGE_SIZE - r, nbytes); + spi_flash_page_program_start(flash_addr, n, p); + flash_addr += n; + p += n; + nbytes -= n; + } + + while (nbytes > 0){ + n = min(SPI_FLASH_PAGE_SIZE, nbytes); + spi_flash_page_program_start(flash_addr, n, p); + flash_addr += n; + p += n; + nbytes -= n; + } + + spi_flash_wait(); + return true; +} + +void +spi_flash_async_erase_start(spi_flash_async_state_t *s, + uint32_t flash_addr, size_t nbytes) +{ + if (nbytes == 0){ + s->first = s->last = s->current = 0; + return; + } + + uint32_t first = round_down(flash_addr, spi_flash_sector_size()); + uint32_t last = round_down(flash_addr + nbytes - 1, spi_flash_sector_size()); + + s->first = first; + s->last = last; + s->current = first; + + spi_flash_erase_sector_start(s->current); +} + +bool +spi_flash_async_erase_poll(spi_flash_async_state_t *s) +{ + if (!spi_flash_done_p()) + return false; + + //printf("%d/%d\n", s->current, s->last); + + // The current sector erase has completed. See if we're finished or + // if there's more to do. + + if (s->current == s->last) // we're done! + return true; + + s->current += spi_flash_sector_size(); + spi_flash_erase_sector_start(s->current); + return false; +} + diff --git a/firmware/microblaze/usrp2p/spi_flash.h b/firmware/microblaze/usrp2p/spi_flash.h new file mode 100644 index 000000000..bbe7b650d --- /dev/null +++ b/firmware/microblaze/usrp2p/spi_flash.h @@ -0,0 +1,119 @@ +/* -*- c -*- */ +/* + * Copyright 2009 Free Software Foundation, Inc. + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#ifndef INCLUDED_SPI_FLASH_H +#define INCLUDED_SPI_FLASH_H + +#include <stddef.h> +#include <stdint.h> +#include <stdbool.h> + + +#define SPI_FLASH_PAGE_SIZE 256 +#define SPI_SS_FLASH 1 + + +uint32_t spi_flash_rdid(void); /* Read ID */ +uint32_t spi_flash_rdsr(void); /* Read Status Register */ +size_t spi_flash_log2_sector_size(void) __attribute__((pure)); /* either 16 or 18 */ +size_t spi_flash_log2_memory_size(void); + +static inline size_t +spi_flash_sector_size(void) +{ + return ((size_t) 1) << spi_flash_log2_sector_size(); +} + +static inline size_t +spi_flash_memory_size(void) +{ + return ((size_t) 1) << spi_flash_log2_memory_size(); +} + +void spi_flash_read(uint32_t flash_addr, size_t nbytes, void *buf); + +/* + * Erase all sectors that fall within the interval [flash_addr, flash_addr + nbytes). + * Erasing sets the memory to ones. + */ +void spi_flash_erase(uint32_t flash_addr, size_t nbytes); + +/* + * Program the flash. + * The area must have been erased prior to programming. + */ +bool spi_flash_program(uint32_t flash_addr, size_t nbytes, const void *buf); + +/* + * --- asynchronous routines --- + */ + +/* + * Is the erasing or programming done? + */ +bool spi_flash_done_p(void); + +/* + * Wait for erasing or programming to complete + */ +void spi_flash_wait(void); + +/* + * Start the erase process on a single sector. + * (It takes between 1 and 3 seconds to erase a 64KB sector) + */ +void spi_flash_erase_sector_start(uint32_t flash_addr); + +/* + * Start the programming process within a single page. + * nbytes must be between 1 and 256. + * (It takes between 1.4 and 5 ms to program a page -> 640 ms for 64KB) + */ +bool spi_flash_page_program_start(uint32_t flash_addr, size_t nbytes, const void *buf); + + +/* + * --- high-level async erase --- + */ + +typedef struct { + uint32_t first; + uint32_t last; + uint32_t current; +} spi_flash_async_state_t; + +/* + * Start to erase all sectors that fall within the interval [flash_addr, flash_addr + nbytes). + * Erasing sets the memory to ones. + * + * Initializes s and begins the process. Call spi_flash_async_erase_poll + * to test for completion and advance state machine. + */ +void spi_flash_async_erase_start(spi_flash_async_state_t *s, + uint32_t flash_addr, size_t nbytes); + +/* + * Poll for aysnc flash erase completion. + * Returns true when the erase has completed. + * (This should be called at something >= 4 Hz. It takes 1 to 3 seconds to + * erase each 64KB sector). + */ +bool spi_flash_async_erase_poll(spi_flash_async_state_t *s); + + +#endif /* INCLUDED_SPI_FLASH_H */ diff --git a/firmware/microblaze/usrp2p/spi_flash_private.h b/firmware/microblaze/usrp2p/spi_flash_private.h new file mode 100644 index 000000000..9a1b8d3e3 --- /dev/null +++ b/firmware/microblaze/usrp2p/spi_flash_private.h @@ -0,0 +1,70 @@ +/* -*- c++ -*- */ +/* + * Copyright 2009 Free Software Foundation, Inc. + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef INCLUDED_SPI_FLASH_PRIVATE_H +#define INCLUDED_SPI_FLASH_PRIVATE_H + +#include "spi_flash.h" +#include "spi.h" +#include "memory_map.h" +#include <string.h> + + +/* M25P64 et al. */ + +#define WREN_CMD 0x06 // write enable +#define WRDI_CMD 0x04 // write disable +#define RDID_CMD 0x9f // read identification +#define RDSR_CMD 0x05 // read status register +#define WRSR_CMD 0x01 // write status register +#define READ_CMD 0x03 +#define FAST_READ_CMD 0x0b +#define PP_CMD 0x02 // page program (256 bytes) +#define SE_CMD 0xd8 // sector erase (64KB) +#define BE_CMD 0xc7 // bulk erase (all) +#define RES_CMD 0xab // read electronic sig (deprecated) + +/* Status register bits */ + +#define SR_SRWD 0x80 +#define SR_BP2 0x10 // block protect bit 2 +#define SR_BP1 0x08 // block protect bit 1 +#define SR_BP0 0x04 // block protect bit 0 +#define SR_WEL 0x02 // Write Enable Latch +#define SR_WIP 0x01 // Write in Progress. Set if busy w/ program or erase cycle. + + +#define FLAGS (SPIF_PUSH_FALL | SPIF_LATCH_RISE) + +#define LEN(x) ((x) & SPI_CTRL_CHAR_LEN_MASK) + + +static inline uint32_t +min(uint32_t a, uint32_t b) +{ + return a < b ? a : b; +} + +static inline uint32_t +round_down(uint32_t x, uint32_t power_of_2) +{ + return x & -power_of_2; +} + +#endif /* INCLUDED_SPI_FLASH_PRIVATE_H */ diff --git a/firmware/microblaze/usrp2p/spi_flash_read.c b/firmware/microblaze/usrp2p/spi_flash_read.c new file mode 100644 index 000000000..4682c5fe6 --- /dev/null +++ b/firmware/microblaze/usrp2p/spi_flash_read.c @@ -0,0 +1,119 @@ +/* -*- c++ -*- */ +/* + * Copyright 2009 Free Software Foundation, Inc. + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "spi_flash_private.h" +#include <stdlib.h> // abort + +static size_t _spi_flash_log2_memory_size; + +uint32_t +spi_flash_rdid(void) +{ + return spif_transact(SPI_TXRX, SPI_SS_FLASH, RDID_CMD << 24, 32, FLAGS) & 0xffffff; +} + +size_t +spi_flash_log2_sector_size(void) +{ + static size_t _spi_flash_log2_sector_size; + + if (_spi_flash_log2_sector_size != 0) + return _spi_flash_log2_sector_size; + + + uint32_t id = spi_flash_rdid(); + int type = (id >> 8) & 0xff; + int size = id & 0xff; + if (type != 0x20 || size < 22 || size > 24) + abort(); + + static unsigned char log2_sector_size[3] = { + 16, /* M25P32 */ + 16, /* M25P64 */ + 18, /* M25P128 */ + }; + + _spi_flash_log2_sector_size = log2_sector_size[size - 22]; + _spi_flash_log2_memory_size = size; //while we're at it + return _spi_flash_log2_sector_size; +} + +size_t +spi_flash_log2_memory_size(void) +{ + if (_spi_flash_log2_memory_size != 0) + return _spi_flash_log2_memory_size; + + uint32_t id = spi_flash_rdid(); + int type = (id >> 8) & 0xff; + int size = id & 0xff; + if (type != 0x20 || size < 22 || size > 24) + abort(); + + _spi_flash_log2_memory_size = size; + return _spi_flash_log2_memory_size; +} + +void +spi_flash_read(uint32_t flash_addr, size_t nbytes, void *buf) +{ + /* + * We explicitly control the slave select here (/S), so that we can + * do the entire read operation as a single transaction from + * device's point of view. (The most our SPI peripheral can transfer + * in a single shot is 16 bytes.) + */ + spif_wait(); + + spif_regs->ss = 0; + spif_regs->ctrl = FLAGS; // ASS is now clear and no chip select is enabled. + + /* + * Do the 5 byte instruction tranfer: + * FAST_READ_CMD, ADDR2, ADDR1, ADDR0, DUMMY + */ + spif_regs->txrx1 = FAST_READ_CMD; + spif_regs->txrx0 = ((flash_addr & 0x00ffffff) << 8); + spif_regs->ss = SPI_SS_FLASH; // assert chip select + spif_regs->ctrl = FLAGS | LEN(5 * 8); + spif_regs->ctrl = FLAGS | LEN(5 * 8) | SPI_CTRL_GO_BSY; + spif_wait(); + + /* + * Read up to 16 bytes at a time until done + */ + unsigned char *dst = (unsigned char *) buf; + size_t m; + for (size_t n = 0; n < nbytes; n += m, dst += m){ + spif_regs->ctrl = FLAGS | LEN(16 * 8); // xfer 16 bytes + spif_regs->ctrl = FLAGS | LEN(16 * 8) | SPI_CTRL_GO_BSY; + spif_wait(); + + uint32_t w[4]; + w[0] = spif_regs->txrx3; // txrx3 has first bits in it + w[1] = spif_regs->txrx2; + w[2] = spif_regs->txrx1; + w[3] = spif_regs->txrx0; + unsigned char *src = (unsigned char *) &w[0]; + m = min(nbytes - n, 16); + for (size_t i = 0; i < m; i++) + dst[i] = src[i]; + } + spif_regs->ss = 0; // deassert chip select +} diff --git a/firmware/microblaze/usrp2p/spif.c b/firmware/microblaze/usrp2p/spif.c new file mode 100644 index 000000000..1c1a348f4 --- /dev/null +++ b/firmware/microblaze/usrp2p/spif.c @@ -0,0 +1,68 @@ +/* + * Copyright 2007,2008,2009 Free Software Foundation, Inc. + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +/* + * Code for the Flash SPI bus + */ + +#include "spi.h" +#include "memory_map.h" + +void +spif_init(void) +{ + /* + * f_sclk = f_wb / ((div + 1) * 2) + */ + spif_regs->div = 1; // 0 = Div by 2 (31.25 MHz); 1 = Div-by-4 (15.625 MHz) + + // run dummy transaction to work around invalid initial clock state + spif_transact(SPI_TXONLY, 0, 0, 8, SPIF_PUSH_FALL | SPIF_LATCH_RISE); +} + +inline void +spif_wait(void) +{ + while (spif_regs->ctrl & SPI_CTRL_GO_BSY) + ; +} + +uint32_t +spif_transact(bool readback_, int slave, uint32_t data, int length, uint32_t flags) +{ + flags &= (SPI_CTRL_TXNEG | SPI_CTRL_RXNEG); + int ctrl = SPI_CTRL_ASS | (SPI_CTRL_CHAR_LEN_MASK & length) | flags; + + spif_wait(); + + // Data we will send + spif_regs->txrx0 = data; + + // Run it -- write once and rewrite with GO set + spif_regs->ctrl = ctrl; + // Tell it which SPI slave device to access + spif_regs->ss = slave & 0xff; + spif_regs->ctrl = ctrl | SPI_CTRL_GO_BSY; + + if(readback_) { + spif_wait(); + return spif_regs->txrx0; + } + else + return 0; +} diff --git a/firmware/microblaze/usrp2p/udp_fw_update.c b/firmware/microblaze/usrp2p/udp_fw_update.c new file mode 100644 index 000000000..55c206b1b --- /dev/null +++ b/firmware/microblaze/usrp2p/udp_fw_update.c @@ -0,0 +1,108 @@ +/* -*- c++ -*- */ +/* + * Copyright 2010 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +//Routines to handle updating the SPI Flash firmware via UDP + +#include <net_common.h> +#include "usrp2/fw_common.h" +#include "spi.h" +#include "spi_flash.h" +#include <nonstdio.h> +#include <string.h> +#include "ethernet.h" +#include "udp_fw_update.h" +#include "xilinx_s3_icap.h" + +//Firmware update packet handler +void handle_udp_fw_update_packet(struct socket_address src, struct socket_address dst, + unsigned char *payload, int payload_len) { + + const usrp2_fw_update_data_t *update_data_in = (usrp2_fw_update_data_t *) payload; + + usrp2_fw_update_data_t update_data_out; + usrp2_fw_update_id_t update_data_in_id = update_data_in->id; + + //ensure that the protocol versions match + if (payload_len >= sizeof(uint32_t) && update_data_in->proto_ver != USRP2_FW_COMPAT_NUM){ + printf("!Error in update packet handler: Expected compatibility number %d, but got %d\n", + USRP2_FW_COMPAT_NUM, update_data_in->proto_ver + ); + update_data_in_id = USRP2_FW_UPDATE_ID_OHAI_LOL; //so we can respond + } + + //ensure that this is not a short packet + if (payload_len < sizeof(usrp2_fw_update_data_t)){ + printf("!Error in update packet handler: Expected payload length %d, but got %d\n", + (int)sizeof(usrp2_fw_update_data_t), payload_len + ); + update_data_in_id = USRP2_FW_UPDATE_ID_WAT; + } + + spi_flash_async_state_t spi_flash_async_state; + + switch(update_data_in_id) { + case USRP2_FW_UPDATE_ID_OHAI_LOL: //why hello there you handsome devil + update_data_out.id = USRP2_FW_UPDATE_ID_OHAI_OMG; + memcpy(&update_data_out.data.ip_addr, (void *)get_ip_addr(), sizeof(struct ip_addr)); + break; + + case USRP2_FW_UPDATE_ID_WATS_TEH_FLASH_INFO_LOL: //query sector size, memory size so the host can mind the boundaries + update_data_out.data.flash_info_args.sector_size_bytes = spi_flash_sector_size(); + update_data_out.data.flash_info_args.memory_size_bytes = spi_flash_memory_size(); + update_data_out.id = USRP2_FW_UPDATE_ID_HERES_TEH_FLASH_INFO_OMG; + break; + + case USRP2_FW_UPDATE_ID_ERASE_TEH_FLASHES_LOL: //out with the old + spi_flash_async_erase_start(&spi_flash_async_state, update_data_in->data.flash_args.flash_addr, update_data_in->data.flash_args.length); + update_data_out.id = USRP2_FW_UPDATE_ID_ERASING_TEH_FLASHES_OMG; + break; + + case USRP2_FW_UPDATE_ID_R_U_DONE_ERASING_LOL: + //poll for done, set something in the reply packet + //spi_flash_async_erase_poll() also advances the state machine, so you should call it reasonably often to get things done quicker + if(spi_flash_async_erase_poll(&spi_flash_async_state)) update_data_out.id = USRP2_FW_UPDATE_ID_IM_DONE_ERASING_OMG; + else update_data_out.id = USRP2_FW_UPDATE_ID_NOPE_NOT_DONE_ERASING_OMG; + break; + + case USRP2_FW_UPDATE_ID_WRITE_TEH_FLASHES_LOL: //and in with the new + //spi_flash_program() goes pretty quick compared to page erases, so we don't bother polling -- it'll come back in some milliseconds + //if it doesn't come back fast enough, we'll just write smaller packets at a time until it does + spi_flash_program(update_data_in->data.flash_args.flash_addr, update_data_in->data.flash_args.length, update_data_in->data.flash_args.data); + update_data_out.id = USRP2_FW_UPDATE_ID_WROTE_TEH_FLASHES_OMG; + break; + + case USRP2_FW_UPDATE_ID_READ_TEH_FLASHES_LOL: //for verify + spi_flash_read(update_data_in->data.flash_args.flash_addr, update_data_in->data.flash_args.length, update_data_out.data.flash_args.data); + update_data_out.id = USRP2_FW_UPDATE_ID_KK_READ_TEH_FLASHES_OMG; + break; + + case USRP2_FW_UPDATE_ID_RESET_MAH_COMPUTORZ_LOL: //for if we ever get the ICAP working + //should reset via icap_reload_fpga(uint32_t flash_address); + update_data_out.id = USRP2_FW_UPDATE_ID_RESETTIN_TEH_COMPUTORZ_OMG; + //you should note that if you get a reply packet to this the reset has obviously failed + icap_reload_fpga(0); + break; + +// case USRP2_FW_UPDATE_ID_KTHXBAI: //see ya +// break; + + default: //uhhhh + update_data_out.id = USRP2_FW_UPDATE_ID_WAT; + } + send_udp_pkt(USRP2_UDP_UPDATE_PORT, src, &update_data_out, sizeof(update_data_out)); +} diff --git a/firmware/microblaze/usrp2p/xilinx_s3_icap.c b/firmware/microblaze/usrp2p/xilinx_s3_icap.c new file mode 100644 index 000000000..50c85231c --- /dev/null +++ b/firmware/microblaze/usrp2p/xilinx_s3_icap.c @@ -0,0 +1,99 @@ +/* -*- c -*- */ +/* + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + + +/* Changes required to work for the Spartan-3A series: + * The ICAP interface on the 3A is 8 bits wide, instead of 32. + * Everything is Xilinx standard LSBit-first. + * The operations are all different. + * Commands are 16 bits long, presented to the ICAP interface 8 bits at a time. +*/ + +#include <xilinx_s3_icap.h> +#include <memory_map.h> +#include <spi_flash_private.h> //for READ_CMD + + +/* bit swap end-for-end */ +static inline unsigned char +swap8(unsigned char x) +{ + unsigned char r = 0; + r |= (x >> 7) & 0x01; + r |= (x >> 5) & 0x02; + r |= (x >> 3) & 0x04; + r |= (x >> 1) & 0x08; + + r |= (x << 1) & 0x10; + r |= (x << 3) & 0x20; + r |= (x << 5) & 0x40; + r |= (x << 7) & 0x80; + + return r; +} + +void +wr_icap(uint8_t x) +{ + icap_regs->icap = swap8(x); +} + +uint8_t +rd_icap(void) +{ + return swap8(icap_regs->icap); +} + + +void +icap_reload_fpga(uint32_t flash_address) +{ + union { + uint32_t i; + uint8_t c[4]; + } t; + t.i = flash_address; + + //note! t.c[0] MUST contain the byte-wide read command for the flash device used. + //for the 25P64, and most other flash devices, this is 0x03. + t.c[0] = FAST_READ_CMD; + + //TODO: look up the watchdog timer, ensure it won't fire too soon + + //UG332 p279 + wr_icap(0xff); + wr_icap(0xff); //dummy word, probably unnecessary + wr_icap(0xAA); + wr_icap(0x99); //sync word + wr_icap(0x32); + wr_icap(0x61); //Type 1 write General 1 (1 word) + wr_icap(t.c[2]); //bits 15-8 + wr_icap(t.c[3]); //bits 7-0 + wr_icap(0x32); + wr_icap(0x81); //Type 1 write General 2 (1 word) + wr_icap(t.c[0]); //C0-C8, the byte-wide read command + wr_icap(t.c[1]); //Upper 8 bits of 24-bit address + wr_icap(0x30); + wr_icap(0xA1); //Type 1 write CMD (1 word) + wr_icap(0x00); + wr_icap(0x0E); //REBOOT command + wr_icap(0x20); + wr_icap(0x00); //Type 1 NOP + wr_icap(0x20); + wr_icap(0x00); +} diff --git a/firmware/microblaze/usrp2p/xilinx_s3_icap.h b/firmware/microblaze/usrp2p/xilinx_s3_icap.h new file mode 100644 index 000000000..7b7e9eccc --- /dev/null +++ b/firmware/microblaze/usrp2p/xilinx_s3_icap.h @@ -0,0 +1,37 @@ +/* -*- c -*- */ +/* + * Copyright 2009 Ettus Research LLC + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef INCLUDED_XILINX_S3_ICAP_H +#define INCLUDED_XILINX_S3_ICAP_H + +#include <stdint.h> + + +void wr_icap(uint8_t x); +uint8_t rd_icap(void); + +//int icap_read_config_reg(int regno); + +/* + * Attempt to reload the fpga from \p flash_address. + * Shouldn't return, but might. + */ +void icap_reload_fpga(uint32_t flash_address); + + +#endif /* INCLUDED_XILINX_S3_ICAP_H */ |