1 files changed, 0 insertions, 251 deletions
diff --git a/control_lib/buffer_int.v b/control_lib/buffer_int.v
deleted file mode 100644
index c33f2779d..000000000
--- a/control_lib/buffer_int.v
+++ /dev/null
@@ -1,251 +0,0 @@
-
-// FIFO Interface to the 2K buffer RAMs
-// Read port is read-acknowledge
-// FIXME do we want to be able to interleave reads and writes?
-
-module buffer_int
-  #(parameter BUFF_NUM = 0)
-    (// Control Interface
-     input clk,
-     input rst,
-     input [31:0] ctrl_word,
-     input go,
-     output done,
-     output error,
-     output idle,
-     
-     // Buffer Interface
-     output en_o,
-     output we_o,
-     output reg [8:0] addr_o,
-     output [31:0] dat_to_buf,
-     input [31:0] dat_from_buf,
-     
-     // Write FIFO Interface
-     input [31:0] wr_dat_i,
-     input wr_write_i,
-     input wr_done_i,
-     input wr_error_i,
-     output reg wr_ready_o,
-     output reg wr_full_o,
-     
-     // Read FIFO Interface
-     output [31:0] rd_dat_o,
-     input rd_read_i,
-     input rd_done_i,
-     input rd_error_i,
-     output reg rd_sop_o,
-     output reg rd_eop_o
-     );
-   
-   reg [31:0] ctrl_reg;
-   reg 	      go_reg;
-   
-   always @(posedge clk)
-     go_reg <= go;
-   
-   always @(posedge clk)
-     if(rst)
-       ctrl_reg <= 0;
-     else
-       if(go & (ctrl_word[31:28] == BUFF_NUM))
-	 ctrl_reg <= ctrl_word;
-   
-   wire [8:0] firstline = ctrl_reg[8:0];
-   wire [8:0] lastline = ctrl_reg[17:9];
-   wire [3:0] step = ctrl_reg[21:18];
-   wire       read = ctrl_reg[22];
-   wire       write = ctrl_reg[23];
-   wire       clear = ctrl_reg[24];
-   //wire [2:0] port = ctrl_reg[27:25];  // Ignored in this block
-   //wire [3:0] buff_num = ctrl_reg[31:28];  // Ignored here ?
-   
-   assign     dat_to_buf = wr_dat_i;
-   assign     rd_dat_o = dat_from_buf;
-   
-   localparam IDLE = 3'd0;
-   localparam PRE_READ = 3'd1;
-   localparam READING = 3'd2;
-   localparam WRITING = 3'd3;
-   localparam ERROR = 3'd4;
-   localparam DONE = 3'd5;
-   
-   reg [2:0]  state;
-   
-   always @(posedge clk)
-     if(rst)
-       begin
-	  state <= IDLE;
-	  rd_sop_o <= 0;
-	  rd_eop_o <= 0;
-	  wr_ready_o <= 0;
-	  wr_full_o <= 0;
-       end
-     else
-       if(clear)
-	 begin
-	    state <= IDLE;
-	    rd_sop_o <= 0;
-	    rd_eop_o <= 0;
-	    wr_ready_o <= 0;
-	    wr_full_o <= 0;
-	 end
-       else 
-	 case(state)
-	   IDLE :
-	     if(go_reg & read)
-	       begin
-		  addr_o <= firstline;
-		  state <= PRE_READ;
-	       end
-	     else if(go_reg & write)
-	       begin
-		  addr_o <= firstline;
-		  state <= WRITING;
-		  wr_ready_o <= 1;
-	       end
-	   
-	   PRE_READ :
-	     begin
-		state <= READING;
-		addr_o <= addr_o + 1;
-		rd_sop_o <= 1;
-	     end
-	   
-	   READING :
-	     if(rd_error_i)
-	       state <= ERROR;
-	     else if(rd_done_i)
-	       state <= DONE;
-	     else if(rd_read_i)
-	       begin
-		  rd_sop_o <= 0;
-		  addr_o <= addr_o + 1;
-		  if(addr_o == lastline)
-		    rd_eop_o <= 1;
-		  else
-		    rd_eop_o <= 0;
-		  if(rd_eop_o)
-		    state <= DONE;
-	       end
-	   
-	   WRITING :
-	     begin
-		if(wr_write_i)
-		  addr_o <= addr_o + 1;  // This was the timing problem, so now it doesn't depend on wr_error_i
-		if(wr_error_i)
-		  begin
-		     state <= ERROR;
-		     wr_ready_o <= 0;
-		  end
-		else
-		  begin
-		     if(wr_write_i)
-		       begin
-			  wr_ready_o <= 0;
-			  if(addr_o == (lastline-1))
-			    wr_full_o <= 1;
-			  if(addr_o == lastline)
-			    state <= DONE;
-		       end
-		     if(wr_done_i)
-		       begin
-			  state <= DONE;
-			  wr_ready_o <= 0;
-		       end
-		  end // else: !if(wr_error_i)
-	     end // case: WRITING
-
-	   DONE :
-	     begin
-		rd_eop_o <= 0;
-		rd_sop_o <= 0;
-		wr_ready_o <= 0;
-		wr_full_o <= 0;
-	     end
-	   
-	 endcase // case(state)
-   
-   // FIXME ignores step for now
-
-   assign     we_o = (state == WRITING) && wr_write_i;  // FIXME potential critical path
-                   // IF this is a timing problem, we could always write when in this state
-   assign     en_o = ~((state==READING)& ~rd_read_i);   // FIXME potential critical path
-   
-   assign     done = (state == DONE);
-   assign     error = (state == ERROR);
-   assign     idle = (state == IDLE);
-endmodule // buffer_int
-
-
-
-// These are 2 other ways for doing the WRITING state, both work.  First one is faster, but confusing
-/*
-	     begin
-		// Gen 4 values -- state, wr_ready_o, addr_o, wr_full_o
-		if(~wr_error_i & wr_write_i & (addr_o == (lastline-1)))
-		  wr_full_o <= 1;
-		if(wr_error_i | wr_write_i | wr_done_i)
-		  wr_ready_o <= 0;
-		if(wr_error_i)
-		  state <= ERROR;
-		else if(wr_done_i | (wr_write_i & (addr_o == lastline)))
-		  state <= DONE;
-		// This one was the timing problem...  now we increment addr_o even if there is an error
-		if(wr_write_i)
-		  addr_o <= addr_o + 1;
-	     end // case: WRITING
-*/	   
-		
-/*      begin
-		if(wr_error_i)
-		  begin
-		     state <= ERROR;
-		     wr_ready_o <= 0;
-		  end
-		else
-		  begin
-		     if(wr_write_i)
-		       begin
-			  wr_ready_o <= 0;
-			  addr_o <= addr_o + 1;
-			  if(addr_o == (lastline-1))
-			    wr_full_o <= 1;
-			  if(addr_o == lastline)
-			    state <= DONE;
-		       end
-		     if(wr_done_i)
-		       begin
-			  state <= DONE;
-			  wr_ready_o <= 0;
-		       end
-		  end // else: !if(wr_error_i)
-	     end // case: WRITING
-*/
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-// Unused old code
-   //assign     rd_empty_o = (state != READING); // && (state != PRE_READ);
-   //assign     rd_empty_o = rd_empty_reg;         // timing fix?
-   //assign     rd_ready_o = (state == READING);
-   //assign     rd_ready_o = ~rd_empty_reg;        // timing fix?
-   
-   //wire       rd_en = (state == PRE_READ) || ((state == READING) && rd_read_i);
-   //wire       wr_en = (state == WRITING) && wr_write_i;  // IF this is a timing problem, we could always enable when in this state
-   //assign     en_o = rd_en | wr_en;   
-   
-   // assign     wr_full_o = (state != WRITING);
-   // assign     wr_ready_o = (state == WRITING);
-