diff options
| -rw-r--r-- | host/docs/usrp_b200.rst | 113 |
1 files changed, 113 insertions, 0 deletions
diff --git a/host/docs/usrp_b200.rst b/host/docs/usrp_b200.rst index b282ec424..1b0d7b719 100644 --- a/host/docs/usrp_b200.rst +++ b/host/docs/usrp_b200.rst @@ -76,3 +76,116 @@ and the transmit frontends have 89.5 dB of available gain. Gain settings are application specific, but it is recommended that users consider using at least half of the available gain to get reasonable dynamic range. + +------------------------------------------------------------------------ +Hardware Reference +------------------------------------------------------------------------ + +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ +LED Indicators +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Below is a table of the LED indicators and their meanings: + +=============== ======================== ======================================================== +Component ID Description Details +=============== ======================== ======================================================== + LED600 Power Indicator | off = no power applied + | red = power applied (external or USB) + LED800 Channel 2 RX2 Activity | off = no activity + | green = receiving + LED801 Channel 2 TX/RX Activity | off = no activity + | green = receiving + | red = transmitting + | orange = switching between transmitting and receiving + LED802 Channel 1 TX/RX Activity | off = no activity + | green = receiving + | red = transmitting + | orange = switching between transmitting and receiving + LED803 Channel 1 RX2 Activity | off = no activity + | green = receiving + LED100 GPS lock indicator | off = no lock + | green = lock +=============== ======================== ======================================================== + +TX LED indicators are on when transimitting data and off when no samples are available to transmit. RX LED indicators are on when sending samples to the host and off when unable to do so. This means that TX/RX activity LED indicators will blink off in a temporary transmit underflow or receive overflow condition, indicating that the host is not sending or receiving samples fast enough. The host will be notified of the condition and output a "U" or "O" as well. + +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ +External Connections +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Below is a table showing the external connections and respective power information: + +=============== ======================== ======================================================== +Component ID Description Details +=============== ======================== ======================================================== + J601 External Power | 6 V + | 3 A + J701 USB Connector | USB 3.0 + J104 External PPS Input | 1.8 V - 5 V + J101 GPS Antenna | GPSDO will supply nominal voltage to antenna. + J100 External 10 MHz Input | +15 dBm max + J800 RF B: TX/RX | TX power +20dBm max + | RX power -15dBm max + J802 RF B: RX2 | RX power -15dBm max + J803 RF A: RX2 | RX power -15dBm max + J801 RF A: TX/RX | TX power +20dBm max + | RX power -15dBm max +=============== ======================== ======================================================== + +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ +On-Board Connectors and Switches +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Below is a table showing the on-board connectors and switches: + +=============== ======================== ======================================================== +Component ID Description Details +=============== ======================== ======================================================== + J502* Mictor Connector | Interface to FPGA for I/O and inspection. + J503* JTAG Header | Interface to FPGA for programming and debugging. + J400 Debug Header | Pin 1 - serial data out (115200 8,N,1 @ 1.8V) + | Pin 2 - ground + | Pin 3 - serial data in (not connected) + S100 GPSDO ISP Enable Switch | Not supported + S700 FX3 Hard Reset Switch +=============== ======================== ======================================================== + +\* B210 Only + +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ +Test Points +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Below is a table showing the test points: + +=============== ================================== =================== +Component ID Description Details +=============== ================================== =================== + J603 Upstream Voltage Regulation | 3.3 V supply + Test Point | Pin 1 - 3.7 V + | Pin 2 - gnd + J604 Catalina Supply Test Point | Pin 1 - 1.3 V + | Pin 2 - gnd + J605 FPGA Supply Test Point | Pin 1 - 1.2 V + | Pin 2 - gnd + J606 FX3 Supply Test Point | Pin 1 - 1.2V + | Pin 2 - gnd + J609 Upstream Voltage Regulation | 1.3 V supply + Test Point | Pin 1 - 1.8 V + | Pin 2 - gnd + T600 External Voltage Supply + Test Point + T601 1.3 V Catalina Power Good + Test Point + T602 1.3 V Catalina Synthesizer + Power Good Test Point + TP302 Catalina AUX DAC1 Test Point + TP303 Catalina AUX DAC2 Test Point + T700 Not connected + T701 Not connected + T702 FX3 External Clock In | Not used + T703 FX3 Charger Detect Out +=============== ================================== =================== + + |