diff options
| -rw-r--r-- | firmware/microblaze/usrp2p/memory_map.h | 62 |
1 files changed, 15 insertions, 47 deletions
diff --git a/firmware/microblaze/usrp2p/memory_map.h b/firmware/microblaze/usrp2p/memory_map.h index 5edb3b313..51e4b9413 100644 --- a/firmware/microblaze/usrp2p/memory_map.h +++ b/firmware/microblaze/usrp2p/memory_map.h @@ -16,38 +16,6 @@ * along with this program. If not, see <http://www.gnu.org/licenses/>. */ -/* Overall Memory Map - * 0000-FFFF 64K RAM space - * - * 0000-1FFF 8K Boot RAM - * 2000-5FFF 16K Buffer pool - * 6000-7FFF 8K Peripherals - * 8000-FFFF 32K Main System RAM - - -From u2plus_core.v: -wb_1master #(.decode_w(8), -.s0_addr(8'b0000_0000),.s0_mask(8'b1110_0000), // 0-8K, Boot RAM -.s1_addr(8'b0100_0000),.s1_mask(8'b1100_0000), // 16K-32K, Buffer Pool -.s2_addr(8'b0011_0000),.s2_mask(8'b1111_1111), // SPI 0x3000 -.s3_addr(8'b0011_0001),.s3_mask(8'b1111_1111), // I2C 0x3100 -.s4_addr(8'b0011_0010),.s4_mask(8'b1111_1111), // GPIO 0x3200 -.s5_addr(8'b0011_0011),.s5_mask(8'b1111_1111), // Readback 0x3300 -.s6_addr(8'b0011_0100),.s6_mask(8'b1111_1111), // Ethernet MAC 0x3400 -.s7_addr(8'b0010_0000),.s7_mask(8'b1111_0000), // 8-12K, Settings Bus (only uses 1K) 0x2000-0x2FFF -.s8_addr(8'b0011_0101),.s8_mask(8'b1111_1111), // PIC 0x3500 -.s9_addr(8'b0011_0110),.s9_mask(8'b1111_1111), // Unused 0x3600 -.sa_addr(8'b0011_0111),.sa_mask(8'b1111_1111), // UART 0x3700 -.sb_addr(8'b0011_1000),.sb_mask(8'b1111_1111), // ATR 0x3800 -.sc_addr(8'b0011_1001),.sc_mask(8'b1111_1111), // Unused 0x3900 -.sd_addr(8'b0011_1010),.sd_mask(8'b1111_1111), // ICAP 0x3A00 -.se_addr(8'b0011_1011),.se_mask(8'b1111_1111), // SPI Flash 0x3B00 -.sf_addr(8'b1000_0000),.sf_mask(8'b1000_0000), // 32-64K, Main RAM 0x8000-0xFFFF - .dw(dw),.aw(aw),.sw(sw)) wb_1master - - */ - - #ifndef INCLUDED_MEMORY_MAP_H #define INCLUDED_MEMORY_MAP_H @@ -88,7 +56,7 @@ wb_1master #(.decode_w(8), ///////////////////////////////////////////////////// // SPI Core, Slave 2. See core docs for more info -#define SPI_BASE 0x3000 // Base address (16-bit) is base peripheral addr +#define SPI_BASE 0x6000 // Base address (16-bit) is base peripheral addr typedef struct { volatile uint32_t txrx0; @@ -127,7 +95,7 @@ typedef struct { // I2C, Slave 3 // See Wishbone I2C-Master Core Specification. -#define I2C_BASE 0x3100 +#define I2C_BASE 0x6100 typedef struct { volatile uint32_t prescaler_lo; // r/w @@ -169,7 +137,7 @@ typedef struct { // // These go to the daughterboard i/o pins -#define GPIO_BASE 0x3200 +#define GPIO_BASE 0x6200 typedef struct { volatile uint32_t io; // tx data in high 16, rx in low 16 @@ -193,7 +161,7 @@ typedef struct { // The status registers are in Slave 5, Buffer Pool Status. // The control register is in Slave 7, Settings Bus. -#define BUFFER_POOL_STATUS_BASE 0x3300 +#define BUFFER_POOL_STATUS_BASE 0x6300 typedef struct { volatile uint32_t _padding[8]; @@ -236,7 +204,7 @@ hwconfig_wishbone_divisor(void) /////////////////////////////////////////////////// // Ethernet Core, Slave 6 -#define ETH_BASE 0x3400 +#define ETH_BASE 0x6400 #include "eth_mac_regs.h" @@ -249,11 +217,11 @@ hwconfig_wishbone_divisor(void) // 1KB of address space (== 256 32-bit write-only regs) -#define MISC_OUTPUT_BASE 0x2000 -#define TX_PROTOCOL_ENGINE_BASE 0x2080 -#define RX_PROTOCOL_ENGINE_BASE 0x20C0 -#define BUFFER_POOL_CTRL_BASE 0x2100 -#define LAST_SETTING_REG 0x23FC // last valid setting register +#define MISC_OUTPUT_BASE 0x5000 +#define TX_PROTOCOL_ENGINE_BASE 0x5080 +#define RX_PROTOCOL_ENGINE_BASE 0x50C0 +#define BUFFER_POOL_CTRL_BASE 0x5100 +#define LAST_SETTING_REG 0x53FC // last valid setting register #define SR_MISC 0 #define SR_TX_PROT_ENG 32 @@ -608,7 +576,7 @@ typedef struct { /////////////////////////////////////////////////// // Simple Programmable Interrupt Controller, Slave 8 -#define PIC_BASE 0x3500 +#define PIC_BASE 0x6500 // Interrupt request lines // Bit numbers (LSB == 0) that correpond to interrupts into PIC @@ -668,7 +636,7 @@ typedef struct { /////////////////////////////////////////////////// // UART, Slave 10 -#define UART_BASE 0x3700 +#define UART_BASE 0x6700 typedef struct { // All elements are 8 bits except for clkdiv (16), but we use uint32 to make @@ -686,7 +654,7 @@ typedef struct { /////////////////////////////////////////////////// // ATR Controller, Slave 11 -#define ATR_BASE 0x3800 +#define ATR_BASE 0x6800 typedef struct { volatile uint32_t v[16]; @@ -705,7 +673,7 @@ typedef struct { /////////////////////////////////////////////////// // ICAP, Slave 13 -#define ICAP_BASE 0x3A00 +#define ICAP_BASE 0x6A00 typedef struct { uint32_t icap; //only the lower 8 bits matter } icap_regs_t; @@ -717,7 +685,7 @@ typedef struct { // Control register definitions are the same as SPI, so use SPI_CTRL_ASS, etc. // Peripheral mask not needed since bus is dedicated (CE held low) -#define SPIF_BASE 0x3B00 +#define SPIF_BASE 0x6B00 typedef struct { volatile uint32_t txrx0; volatile uint32_t txrx1; |