diff options
| -rw-r--r-- | host/docs/usrp_e3x0.dox | 30 |
1 files changed, 13 insertions, 17 deletions
diff --git a/host/docs/usrp_e3x0.dox b/host/docs/usrp_e3x0.dox index f857676c7..289ea3410 100644 --- a/host/docs/usrp_e3x0.dox +++ b/host/docs/usrp_e3x0.dox @@ -2,7 +2,7 @@ \tableofcontents -\section e3x0_feature_list Comparative features list - E300/E310 +\section e3x0_feature_list Comparative features list - E310 - Hardware Capabilities: Integrated RF frontend (70 MHz - 6 GHz) @@ -16,12 +16,8 @@ - USB UART - Zynq-7020 FPGA - FPGA Capabilities: - - E310 Only: - - 2 RX DDC chains in FPGA - - 2 TX DUC chain in FPGA - - E300 Only: - - 1 RX DDC chains in FPGA - - 1 TX DUC chain in FPGA + - 2 RX DDC chains in FPGA + - 2 TX DUC chain in FPGA - Timed commands in FPGA - Timed sampling in FPGA - 16-bit fixed point sample mode (sc16) @@ -29,7 +25,7 @@ \section e3x0_getting_started Getting started -This will run you through the first steps relevant to get your USRP E300/310 +This will run you through the first steps relevant to get your USRP E310 up and running. \subsection e3x0_first_boot First boot @@ -52,7 +48,7 @@ a terminal emulator such as screen can be used: $ sudo screen /dev/ttyUSB0 115200 The exact device node /dev/ttyUSB0 depends on your operating system's driver and other USB devices that might be already connected. -It can be usually found by perusing the output of dmesg or journalctl, after connecting the USRP E300/E310 device to your host computer. +It can be usually found by perusing the output of dmesg or journalctl, after connecting the USRP E310 device to your host computer. An example of a dmesg output for the serial to usb converter: @@ -74,7 +70,7 @@ You should be presented with a shell similar to the following \subsubsection e3x0_first_boot_ssh SSH connection -The USRP E300/E310 device relies on the DHCP protocol to automatically obtain an IP address. +The USRP E310 device relies on the DHCP protocol to automatically obtain an IP address. In case your network setup does not include a DHCP server, refer to the section \ref e3x0_first_boot_serial or configure a DHCP server to hand out IP addresses on your network. After the device obtained an IP address you can log in from a Linux or OSX machine by typing: @@ -92,7 +88,7 @@ You should be presented with a shell similar to the following \section e3x0_sdk Using the SDK In order to facilitate software development for the integrated ARM Cortex-A9 processor, a <a href="http://www.yoctoproject.org">Yocto Project</a> based SDK is provided in the download section of our website. -This SDK contains a cross-compiler, a cross-linker as well as a cross-debugger and can be used to develop your user space applications for the Ettus USRP-E300/E310 devices. +This SDK contains a cross-compiler, a cross-linker as well as a cross-debugger and can be used to develop your user space applications for the Ettus USRP-E310 devices. \subsection e3x0_sdk_installation Installation @@ -123,7 +119,7 @@ in order to build software for your device open a new shell and type: $ . <yoursdkinstallpath>/environment-setup-armv7ahf-vfp-neon-oe-linux-gnueabi -This will modifiy the PATH, CC, CXX etc, environment variables and allow you to compile software for your USRP E300/E310 device. +This will modifiy the PATH, CC, CXX etc, environment variables and allow you to compile software for your USRP E310 device. To verify all went well you can try: $ $CC -dumpmachine @@ -220,7 +216,7 @@ again by: \subsection e3x0_load_fpga_imgs_uhd Using UHD to load FPGA images -UHD software will automatically select the USRP E300/E310 images from the +UHD software will automatically select the USRP E310 images from the installed images package. The image selection can be overridden with the `fpga` device address parameter. @@ -252,7 +248,7 @@ You may need to change the USRP's IP address for several reasons: \subsection e3x0_hw_fpanel Front Panel -\image html e3x0_fp_overlay.png "USRP E300/E310 Front panel" +\image html e3x0_fp_overlay.png "USRP E310 Front panel" - **RF A Group** + **TX/RX LED**: Indicates that data is streaming on the TX/RX channel on frontend side A @@ -271,7 +267,7 @@ You may need to change the USRP's IP address for several reasons: \subsection e3x0_hw_rear_panel Rear Panel -\image html e3x0_rp_overlay.png "USRP E300/E310 Rear Panel" +\image html e3x0_rp_overlay.png "USRP E310 Rear Panel" - **PWR**: Locking connector for the USRP-E Series power supply - **1G ETH**: RJ45 port for Ethernet interfaces @@ -501,11 +497,11 @@ by pinging the USRP and making sure the LEDs start to blink. \subsection e3x0_apps_gsm GSM Base Station -OpenBTS allows the USRP E300/E310 to serve as a GSM base station capable of providing voice and messaging services to standard GSM handsets. General information on the OpenBTS project can be found at the official webpage. +OpenBTS allows the USRP E310 to serve as a GSM base station capable of providing voice and messaging services to standard GSM handsets. General information on the OpenBTS project can be found at the official webpage. http://www.openbts.org -Special instructions to install OpenBTS on the E300/E310 can be found on the OpenBTS wiki. +Special instructions to install OpenBTS on the E310 can be found on the OpenBTS wiki. http://openbts.org/w/index.php/E3x0 |