diff options
139 files changed, 11210 insertions, 232 deletions
diff --git a/fpga/usrp2/control_lib/Makefile.srcs b/fpga/usrp2/control_lib/Makefile.srcs index bc8e4d5bc..383ed97d8 100644 --- a/fpga/usrp2/control_lib/Makefile.srcs +++ b/fpga/usrp2/control_lib/Makefile.srcs @@ -42,4 +42,7 @@ pic.v \ longfifo.v \ shortfifo.v \ medfifo.v \ +nsgpio16LE.v \ +settings_bus_16LE.v \ +atr_controller16.v \ )) diff --git a/fpga/usrp2/control_lib/atr_controller16.v b/fpga/usrp2/control_lib/atr_controller16.v new file mode 100644 index 000000000..3d8b5b1e9 --- /dev/null +++ b/fpga/usrp2/control_lib/atr_controller16.v @@ -0,0 +1,60 @@ + +// Automatic transmit/receive switching of control pins to daughterboards +// Store everything in registers for now, but could use a RAM for more +// complex state machines in the future + +module atr_controller16 + (input clk_i, input rst_i, + input [5:0] adr_i, input [1:0] sel_i, input [15:0] dat_i, output reg [15:0] dat_o, + input we_i, input stb_i, input cyc_i, output reg ack_o, + input run_rx, input run_tx, input [31:0] master_time, + output [31:0] ctrl_lines); + + reg [3:0] state; + reg [31:0] atr_ram [0:15]; // DP distributed RAM + + wire [3:0] sel_int = { (sel_i[1] & adr_i[1]), (sel_i[0] & adr_i[1]), + (sel_i[1] & ~adr_i[1]), (sel_i[0] & ~adr_i[1]) }; + + // WB Interface + always @(posedge clk_i) + if(we_i & stb_i & cyc_i) + begin + if(sel_int[3]) + atr_ram[adr_i[5:2]][31:24] <= dat_i[15:8]; + if(sel_int[2]) + atr_ram[adr_i[5:2]][23:16] <= dat_i[7:0]; + if(sel_int[1]) + atr_ram[adr_i[5:2]][15:8] <= dat_i[15:8]; + if(sel_int[0]) + atr_ram[adr_i[5:2]][7:0] <= dat_i[7:0]; + end // if (we_i & stb_i & cyc_i) + + always @(posedge clk_i) + dat_o <= adr_i[1] ? atr_ram[adr_i[5:2]][31:16] : atr_ram[adr_i[5:2]][15:0]; + + always @(posedge clk_i) + ack_o <= stb_i & cyc_i & ~ack_o; + + // Control side of DP RAM + assign ctrl_lines = atr_ram[state]; + + // Put a more complex state machine with time delays and multiple states here + // if daughterboard requires more complex sequencing + localparam ATR_IDLE = 4'd0; + localparam ATR_TX = 4'd1; + localparam ATR_RX = 4'd2; + localparam ATR_FULL_DUPLEX = 4'd3; + + always @(posedge clk_i) + if(rst_i) + state <= ATR_IDLE; + else + case ({run_rx,run_tx}) + 2'b00 : state <= ATR_IDLE; + 2'b01 : state <= ATR_TX; + 2'b10 : state <= ATR_RX; + 2'b11 : state <= ATR_FULL_DUPLEX; + endcase // case({run_rx,run_tx}) + +endmodule // atr_controller16 diff --git a/fpga/usrp2/control_lib/newfifo/fifo_pacer.v b/fpga/usrp2/control_lib/newfifo/fifo_pacer.v new file mode 100644 index 000000000..1bf03ab6e --- /dev/null +++ b/fpga/usrp2/control_lib/newfifo/fifo_pacer.v @@ -0,0 +1,24 @@ + + +module fifo_pacer + (input clk, + input reset, + input [7:0] rate, + input enable, + input src1_rdy_i, output dst1_rdy_o, + output src2_rdy_o, input dst2_rdy_i, + output underrun, overrun); + + wire strobe; + + cic_strober strober (.clock(clk), .reset(reset), .enable(enable), + .rate(rate), .strobe_fast(1), .strobe_slow(strobe)); + + wire all_ready = src1_rdy_i & dst2_rdy_i; + assign dst1_rdy_o = all_ready & strobe; + assign src2_rdy_o = dst1_rdy_o; + + assign underrun = strobe & ~src1_rdy_i; + assign overrun = strobe & ~dst2_rdy_i; + +endmodule // fifo_pacer diff --git a/fpga/usrp2/control_lib/newfifo/packet32_tb.v b/fpga/usrp2/control_lib/newfifo/packet32_tb.v new file mode 100644 index 000000000..82bb09c29 --- /dev/null +++ b/fpga/usrp2/control_lib/newfifo/packet32_tb.v @@ -0,0 +1,27 @@ + + +module packet32_tb(); + + wire [35:0] data; + wire src_rdy, dst_rdy; + + wire clear = 0; + reg clk = 0; + reg reset = 1; + + always #10 clk <= ~clk; + initial #1000 reset <= 0; + + initial $dumpfile("packet32_tb.vcd"); + initial $dumpvars(0,packet32_tb); + + wire [31:0] total, crc_err, seq_err, len_err; + + packet_generator32 pkt_gen (.clk(clk), .reset(reset), .clear(clear), + .data_o(data), .src_rdy_o(src_rdy), .dst_rdy_i(dst_rdy)); + + packet_verifier32 pkt_ver (.clk(clk), .reset(reset), .clear(clear), + .data_i(data), .src_rdy_i(src_rdy), .dst_rdy_o(dst_rdy), + .total(total), .crc_err(crc_err), .seq_err(seq_err), .len_err(len_err)); + +endmodule // packet32_tb diff --git a/fpga/usrp2/control_lib/newfifo/packet_generator.v b/fpga/usrp2/control_lib/newfifo/packet_generator.v new file mode 100644 index 000000000..6e8b45ccd --- /dev/null +++ b/fpga/usrp2/control_lib/newfifo/packet_generator.v @@ -0,0 +1,59 @@ + + +module packet_generator + (input clk, input reset, input clear, + output reg [7:0] data_o, output sof_o, output eof_o, + output src_rdy_o, input dst_rdy_i); + + localparam len = 32'd2000; + + reg [31:0] state; + reg [31:0] seq; + wire [31:0] crc_out; + wire calc_crc = src_rdy_o & dst_rdy_i & ~(state[31:2] == 30'h3FFF_FFFF); + + + always @(posedge clk) + if(reset | clear) + seq <= 0; + else + if(eof_o & src_rdy_o & dst_rdy_i) + seq <= seq + 1; + + always @(posedge clk) + if(reset | clear) + state <= 0; + else + if(src_rdy_o & dst_rdy_i) + if(state == (len - 1)) + state <= 32'hFFFF_FFFC; + else + state <= state + 1; + + always @* + case(state) + 0 : data_o <= len[7:0]; + 1 : data_o <= len[15:8]; + 2 : data_o <= len[23:16]; + 3 : data_o <= len[31:24]; + 4 : data_o <= seq[7:0]; + 5 : data_o <= seq[15:8]; + 6 : data_o <= seq[23:16]; + 7 : data_o <= seq[31:24]; + 32'hFFFF_FFFC : data_o <= crc_out[31:24]; + 32'hFFFF_FFFD : data_o <= crc_out[23:16]; + 32'hFFFF_FFFE : data_o <= crc_out[15:8]; + 32'hFFFF_FFFF : data_o <= crc_out[7:0]; + default : data_o <= state[7:0]; + endcase // case (state) + + assign src_rdy_o = 1; + assign sof_o = (state == 0); + assign eof_o = (state == 32'hFFFF_FFFF); + + wire clear_crc = eof_o & src_rdy_o & dst_rdy_i; + + crc crc(.clk(clk), .reset(reset), .clear(clear_crc), .data(data_o), + .calc(calc_crc), .crc_out(crc_out), .match()); + +endmodule // packet_generator diff --git a/fpga/usrp2/control_lib/newfifo/packet_generator32.v b/fpga/usrp2/control_lib/newfifo/packet_generator32.v new file mode 100644 index 000000000..6f8004964 --- /dev/null +++ b/fpga/usrp2/control_lib/newfifo/packet_generator32.v @@ -0,0 +1,21 @@ + + +module packet_generator32 + (input clk, input reset, input clear, + output [35:0] data_o, output src_rdy_o, input dst_rdy_i); + + wire [7:0] ll_data; + wire ll_sof, ll_eof, ll_src_rdy, ll_dst_rdy_n; + + packet_generator pkt_gen + (.clk(clk), .reset(reset), .clear(clear), + .data_o(ll_data), .sof_o(ll_sof), .eof_o(ll_eof), + .src_rdy_o(ll_src_rdy), .dst_rdy_i(~ll_dst_rdy_n)); + + ll8_to_fifo36 ll8_to_f36 + (.clk(clk), .reset(reset), .clear(clear), + .ll_data(ll_data), .ll_sof_n(~ll_sof), .ll_eof_n(~ll_eof), + .ll_src_rdy_n(~ll_src_rdy), .ll_dst_rdy_n(ll_dst_rdy_n), + .f36_data(data_o), .f36_src_rdy_o(src_rdy_o), .f36_dst_rdy_i(dst_rdy_i)); + +endmodule // packet_generator32 diff --git a/fpga/usrp2/control_lib/newfifo/packet_tb.v b/fpga/usrp2/control_lib/newfifo/packet_tb.v new file mode 100644 index 000000000..3c423d2ba --- /dev/null +++ b/fpga/usrp2/control_lib/newfifo/packet_tb.v @@ -0,0 +1,29 @@ + + +module packet_tb(); + + wire [7:0] data; + wire sof, eof, src_rdy, dst_rdy; + + wire clear = 0; + reg clk = 0; + reg reset = 1; + + always #10 clk <= ~clk; + initial #1000 reset <= 0; + + initial $dumpfile("packet_tb.vcd"); + initial $dumpvars(0,packet_tb); + + wire [31:0] total, crc_err, seq_err, len_err; + + packet_generator pkt_gen (.clk(clk), .reset(reset), .clear(clear), + .data_o(data), .sof_o(sof), .eof_o(eof), + .src_rdy_o(src_rdy), .dst_rdy_i(dst_rdy)); + + packet_verifier pkt_ver (.clk(clk), .reset(reset), .clear(clear), + .data_i(data), .sof_i(sof), .eof_i(eof), + .src_rdy_i(src_rdy), .dst_rdy_o(dst_rdy), + .total(total), .crc_err(crc_err), .seq_err(seq_err), .len_err(len_err)); + +endmodule // packet_tb diff --git a/fpga/usrp2/control_lib/newfifo/packet_verifier.v b/fpga/usrp2/control_lib/newfifo/packet_verifier.v new file mode 100644 index 000000000..b49ad1bbb --- /dev/null +++ b/fpga/usrp2/control_lib/newfifo/packet_verifier.v @@ -0,0 +1,61 @@ + + +// Packet format -- +// Line 1 -- Length, 32 bits +// Line 2 -- Sequence number, 32 bits +// Last line -- CRC, 32 bits + +module packet_verifier + (input clk, input reset, input clear, + input [7:0] data_i, input sof_i, input eof_i, input src_rdy_i, output dst_rdy_o, + + output reg [31:0] total, + output reg [31:0] crc_err, + output reg [31:0] seq_err, + output reg [31:0] len_err); + + reg [31:0] seq_num; + reg [31:0] length; + wire first_byte, last_byte; + reg second_byte, last_byte_d1; + + wire calc_crc = src_rdy_i & dst_rdy_o; + + crc crc(.clk(clk), .reset(reset), .clear(last_byte_d1), .data(data_i), + .calc(calc_crc), .crc_out(), .match(match_crc)); + + assign first_byte = src_rdy_i & dst_rdy_o & sof_i; + assign last_byte = src_rdy_i & dst_rdy_o & eof_i; + assign dst_rdy_o = ~last_byte_d1; + + // stubs for now + wire match_seq = 1; + wire match_len = 1; + + always @(posedge clk) + if(reset | clear) + last_byte_d1 <= 0; + else + last_byte_d1 <= last_byte; + + always @(posedge clk) + if(reset | clear) + begin + total <= 0; + crc_err <= 0; + seq_err <= 0; + len_err <= 0; + end + else + if(last_byte_d1) + begin + total <= total + 1; + if(~match_crc) + crc_err <= crc_err + 1; + else if(~match_seq) + seq_err <= seq_err + 1; + else if(~match_len) + seq_err <= len_err + 1; + end + +endmodule // packet_verifier diff --git a/fpga/usrp2/control_lib/newfifo/packet_verifier32.v b/fpga/usrp2/control_lib/newfifo/packet_verifier32.v new file mode 100644 index 000000000..06a13d242 --- /dev/null +++ b/fpga/usrp2/control_lib/newfifo/packet_verifier32.v @@ -0,0 +1,30 @@ + + +module packet_verifier32 + (input clk, input reset, input clear, + input [35:0] data_i, input src_rdy_i, output dst_rdy_o, + output [31:0] total, output [31:0] crc_err, output [31:0] seq_err, output [31:0] len_err); + + wire [7:0] ll_data; + wire ll_sof_n, ll_eof_n, ll_src_rdy_n, ll_dst_rdy; + wire [35:0] data_int; + wire src_rdy_int, dst_rdy_int; + + fifo_short #(.WIDTH(36)) fifo_short + (.clk(clk), .reset(reset), .clear(clear), + .datain(data_i), .src_rdy_i(src_rdy_i), .dst_rdy_o(dst_rdy_o), + .dataout(data_int), .src_rdy_o(src_rdy_int), .dst_rdy_i(dst_rdy_int)); + + fifo36_to_ll8 f36_to_ll8 + (.clk(clk), .reset(reset), .clear(clear), + .f36_data(data_int), .f36_src_rdy_i(src_rdy_int), .f36_dst_rdy_o(dst_rdy_int), + .ll_data(ll_data), .ll_sof_n(ll_sof_n), .ll_eof_n(ll_eof_n), + .ll_src_rdy_n(ll_src_rdy_n), .ll_dst_rdy_n(~ll_dst_rdy)); + + packet_verifier pkt_ver + (.clk(clk), .reset(reset), .clear(clear), + .data_i(ll_data), .sof_i(~ll_sof_n), .eof_i(~ll_eof_n), + .src_rdy_i(~ll_src_rdy_n), .dst_rdy_o(ll_dst_rdy), + .total(total), .crc_err(crc_err), .seq_err(seq_err), .len_err(len_err)); + +endmodule // packet_verifier32 diff --git a/fpga/usrp2/control_lib/nsgpio16LE.v b/fpga/usrp2/control_lib/nsgpio16LE.v new file mode 100644 index 000000000..8aef0c7ae --- /dev/null +++ b/fpga/usrp2/control_lib/nsgpio16LE.v @@ -0,0 +1,123 @@ +// Modified from code originally by Richard Herveille, his copyright is below + +///////////////////////////////////////////////////////////////////// +//// //// +//// OpenCores Simple General Purpose IO core //// +//// //// +//// Author: Richard Herveille //// +//// richard@asics.ws //// +//// www.asics.ws //// +//// //// +///////////////////////////////////////////////////////////////////// +//// //// +//// Copyright (C) 2002 Richard Herveille //// +//// richard@asics.ws //// +//// //// +//// This source file may be used and distributed without //// +//// restriction provided that this copyright statement is not //// +//// removed from the file and that any derivative work contains //// +//// the original copyright notice and the associated disclaimer.//// +//// //// +//// THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY //// +//// EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED //// +//// TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS //// +//// FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL THE AUTHOR //// +//// OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, //// +//// INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES //// +//// (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE //// +//// GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR //// +//// BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF //// +//// LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT //// +//// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT //// +//// OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE //// +//// POSSIBILITY OF SUCH DAMAGE. //// +//// //// +///////////////////////////////////////////////////////////////////// + + +module nsgpio16LE + (input clk_i, input rst_i, + input cyc_i, input stb_i, input [3:0] adr_i, input we_i, input [15:0] dat_i, + output reg [15:0] dat_o, output reg ack_o, + input [31:0] atr, input [31:0] debug_0, input [31:0] debug_1, + inout [31:0] gpio + ); + + reg [31:0] ctrl, line, ddr, dbg, lgpio; + + wire wb_acc = cyc_i & stb_i; // WISHBONE access + wire wb_wr = wb_acc & we_i; // WISHBONE write access + + always @(posedge clk_i or posedge rst_i) + if (rst_i) + begin + ctrl <= 32'h0; + line <= 32'h0; + ddr <= 32'h0; + dbg <= 32'h0; + end + else if (wb_wr) + case( adr_i[3:1] ) + 3'b000 : + line[15:0] <= dat_i; + 3'b001 : + line[31:16] <= dat_i; + 3'b010 : + ddr[15:0] <= dat_i; + 3'b011 : + ddr[31:16] <= dat_i; + 3'b100 : + ctrl[15:0] <= dat_i; + 3'b101 : + ctrl[31:16] <= dat_i; + 3'b110 : + dbg[15:0] <= dat_i; + 3'b111 : + dbg[31:16] <= dat_i; + endcase // case ( adr_i[3:1] ) + + always @(posedge clk_i) + case (adr_i[3:1]) + 3'b000 : + dat_o <= lgpio[15:0]; + 3'b001 : + dat_o <= lgpio[31:16]; + 3'b010 : + dat_o <= ddr[15:0]; + 3'b011 : + dat_o <= ddr[31:16]; + 3'b100 : + dat_o <= ctrl[15:0]; + 3'b101 : + dat_o <= ctrl[31:16]; + 3'b110 : + dat_o <= dbg[15:0]; + 3'b111 : + dat_o <= dbg[31:16]; + endcase // case (adr_i[3:1]) + + + always @(posedge clk_i or posedge rst_i) + if (rst_i) + ack_o <= 1'b0; + else + ack_o <= wb_acc & !ack_o; + + // latch GPIO input pins + always @(posedge clk_i) + lgpio <= gpio; + + // assign GPIO outputs + integer n; + reg [31:0] igpio; // temporary internal signal + + always @(ctrl or line or debug_1 or debug_0 or atr or ddr or dbg) + for(n=0;n<32;n=n+1) + igpio[n] <= ddr[n] ? (dbg[n] ? (ctrl[n] ? debug_1[n] : debug_0[n]) : + (ctrl[n] ? atr[n] : line[n]) ) + : 1'bz; + + assign gpio = igpio; + +endmodule + diff --git a/fpga/usrp2/control_lib/ram_2port_mixed_width.v b/fpga/usrp2/control_lib/ram_2port_mixed_width.v new file mode 100644 index 000000000..fae7d8de3 --- /dev/null +++ b/fpga/usrp2/control_lib/ram_2port_mixed_width.v @@ -0,0 +1,120 @@ + +module ram_2port_mixed_width + (input clk16, + input en16, + input we16, + input [10:0] addr16, + input [15:0] di16, + output [15:0] do16, + input clk32, + input en32, + input we32, + input [9:0] addr32, + input [31:0] di32, + output [31:0] do32); + + wire en32a = en32 & ~addr32[9]; + wire en32b = en32 & addr32[9]; + wire en16a = en16 & ~addr16[10]; + wire en16b = en16 & addr16[10]; + + wire [31:0] do32a, do32b; + wire [15:0] do16a, do16b; + + assign do32 = addr32[9] ? do32b : do32a; + assign do16 = addr16[10] ? do16b : do16a; + + RAMB16BWE_S36_S18 #(.INIT_A(36'h000000000), + .INIT_B(18'h00000), + .SIM_COLLISION_CHECK("ALL"), // "NONE", "WARNING_ONLY", "GENERATE_X_ONLY", "ALL" + .SRVAL_A(36'h000000000), // Port A output value upon SSR assertion + .SRVAL_B(18'h00000), // Port B output value upon SSR assertion + .WRITE_MODE_A("WRITE_FIRST"), // WRITE_FIRST, READ_FIRST or NO_CHANGE + .WRITE_MODE_B("WRITE_FIRST") // WRITE_FIRST, READ_FIRST or NO_CHANGE + ) + RAMB16BWE_S36_S18_0 (.DOA(do32a), // Port A 32-bit Data Output + .DOB(do16a), // Port B 16-bit Data Output + .DOPA(), // Port A 4-bit Parity Output + .DOPB(), // Port B 2-bit Parity Output + .ADDRA(addr32[8:0]), // Port A 9-bit Address Input + .ADDRB(addr16[9:0]), // Port B 10-bit Address Input + .CLKA(clk32), // Port A 1-bit Clock + .CLKB(clk16), // Port B 1-bit Clock + .DIA(di32), // Port A 32-bit Data Input + .DIB(di16), // Port B 16-bit Data Input + .DIPA(0), // Port A 4-bit parity Input + .DIPB(0), // Port-B 2-bit parity Input + .ENA(en32a), // Port A 1-bit RAM Enable Input + .ENB(en16a), // Port B 1-bit RAM Enable Input + .SSRA(0), // Port A 1-bit Synchronous Set/Reset Input + .SSRB(0), // Port B 1-bit Synchronous Set/Reset Input + .WEA({4{we32}}), // Port A 4-bit Write Enable Input + .WEB({2{we16}}) // Port B 2-bit Write Enable Input + ); + + RAMB16BWE_S36_S18 #(.INIT_A(36'h000000000), + .INIT_B(18'h00000), + .SIM_COLLISION_CHECK("ALL"), // "NONE", "WARNING_ONLY", "GENERATE_X_ONLY", "ALL" + .SRVAL_A(36'h000000000), // Port A output value upon SSR assertion + .SRVAL_B(18'h00000), // Port B output value upon SSR assertion + .WRITE_MODE_A("WRITE_FIRST"), // WRITE_FIRST, READ_FIRST or NO_CHANGE + .WRITE_MODE_B("WRITE_FIRST") // WRITE_FIRST, READ_FIRST or NO_CHANGE + ) + RAMB16BWE_S36_S18_1 (.DOA(do32b), // Port A 32-bit Data Output + .DOB(do16b), // Port B 16-bit Data Output + .DOPA(), // Port A 4-bit Parity Output + .DOPB(), // Port B 2-bit Parity Output + .ADDRA(addr32[8:0]), // Port A 9-bit Address Input + .ADDRB(addr16[9:0]), // Port B 10-bit Address Input + .CLKA(clk32), // Port A 1-bit Clock + .CLKB(clk16), // Port B 1-bit Clock + .DIA(di32), // Port A 32-bit Data Input + .DIB(di16), // Port B 16-bit Data Input + .DIPA(0), // Port A 4-bit parity Input + .DIPB(0), // Port-B 2-bit parity Input + .ENA(en32b), // Port A 1-bit RAM Enable Input + .ENB(en16b), // Port B 1-bit RAM Enable Input + .SSRA(0), // Port A 1-bit Synchronous Set/Reset Input + .SSRB(0), // Port B 1-bit Synchronous Set/Reset Input + .WEA({4{we32}}), // Port A 4-bit Write Enable Input + .WEB({2{we16}}) // Port B 2-bit Write Enable Input + ); + +endmodule // ram_2port_mixed_width + + + + +// ISE 10.1.03 chokes on the following + +/* + + reg [31:0] ram [(1<<AWIDTH)-1:0]; + integer i; + initial + for(i=0;i<512;i=i+1) + ram[i] <= 32'b0; + + always @(posedge clk16) + if (en16) + begin + if (we16) + if(addr16[0]) + ram[addr16[10:1]][15:0] <= di16; + else + ram[addr16[10:1]][31:16] <= di16; + do16 <= addr16[0] ? ram[addr16[10:1]][15:0] : ram[addr16[10:1]][31:16]; + end + + always @(posedge clk32) + if (en32) + begin + if (we32) + ram[addr32] <= di32; + do32 <= ram[addr32]; + end + +endmodule // ram_2port_mixed_width + + + */ diff --git a/fpga/usrp2/control_lib/settings_bus.v b/fpga/usrp2/control_lib/settings_bus.v index fc960e456..aec179516 100644 --- a/fpga/usrp2/control_lib/settings_bus.v +++ b/fpga/usrp2/control_lib/settings_bus.v @@ -10,7 +10,7 @@ module settings_bus input wb_stb_i, input wb_we_i, output reg wb_ack_o, - output strobe, + output reg strobe, output reg [7:0] addr, output reg [31:0] data); @@ -19,18 +19,18 @@ module settings_bus always @(posedge wb_clk) if(wb_rst) begin - stb_int <= 1'b0; + strobe <= 1'b0; addr <= 8'd0; data <= 32'd0; end - else if(wb_we_i & wb_stb_i) + else if(wb_we_i & wb_stb_i & ~wb_ack_o) begin - stb_int <= 1'b1; + strobe <= 1'b1; addr <= wb_adr_i[9:2]; data <= wb_dat_i; end else - stb_int <= 1'b0; + strobe <= 1'b0; always @(posedge wb_clk) if(wb_rst) @@ -38,11 +38,4 @@ module settings_bus else wb_ack_o <= wb_stb_i & ~wb_ack_o; - always @(posedge wb_clk) - stb_int_d1 <= stb_int; - - //assign strobe = stb_int & ~stb_int_d1; - assign strobe = stb_int & wb_ack_o; - endmodule // settings_bus - diff --git a/fpga/usrp2/control_lib/settings_bus_16LE.v b/fpga/usrp2/control_lib/settings_bus_16LE.v new file mode 100644 index 000000000..76061e9e0 --- /dev/null +++ b/fpga/usrp2/control_lib/settings_bus_16LE.v @@ -0,0 +1,54 @@ + +// Grab settings off the wishbone bus, send them out to settings bus +// 16 bits little endian, but all registers need to be written 32 bits at a time. +// This means that you write the low 16 bits first and then the high 16 bits. +// The setting regs are strobed when the high 16 bits are written + +module settings_bus_16LE + #(parameter AWIDTH=16, RWIDTH=8) + (input wb_clk, + input wb_rst, + input [AWIDTH-1:0] wb_adr_i, + input [15:0] wb_dat_i, + input wb_stb_i, + input wb_we_i, + output reg wb_ack_o, + output strobe, + output reg [7:0] addr, + output reg [31:0] data); + + reg stb_int; + + always @(posedge wb_clk) + if(wb_rst) + begin + stb_int <= 1'b0; + addr <= 8'd0; + data <= 32'd0; + end + else if(wb_we_i & wb_stb_i) + begin + addr <= wb_adr_i[RWIDTH+1:2]; // Zero pad high bits + if(wb_adr_i[1]) + begin + stb_int <= 1'b1; // We now have both halves + data[31:16] <= wb_dat_i; + end + else + begin + stb_int <= 1'b0; // Don't strobe, we need other half + data[15:0] <= wb_dat_i; + end + end + else + stb_int <= 1'b0; + + always @(posedge wb_clk) + if(wb_rst) + wb_ack_o <= 0; + else + wb_ack_o <= wb_stb_i & ~wb_ack_o; + + assign strobe = stb_int & wb_ack_o; + +endmodule // settings_bus_16LE diff --git a/fpga/usrp2/control_lib/simple_uart.v b/fpga/usrp2/control_lib/simple_uart.v index 22f0e70a2..0dd58b5f5 100644 --- a/fpga/usrp2/control_lib/simple_uart.v +++ b/fpga/usrp2/control_lib/simple_uart.v @@ -1,11 +1,12 @@ module simple_uart #(parameter TXDEPTH = 1, - parameter RXDEPTH = 1) - (input clk_i, input rst_i, - input we_i, input stb_i, input cyc_i, output reg ack_o, - input [2:0] adr_i, input [31:0] dat_i, output reg [31:0] dat_o, - output rx_int_o, output tx_int_o, output tx_o, input rx_i, output baud_o); + parameter RXDEPTH = 1, + parameter CLKDIV_DEFAULT = 16'd0) + (input clk_i, input rst_i, + input we_i, input stb_i, input cyc_i, output reg ack_o, + input [2:0] adr_i, input [31:0] dat_i, output reg [31:0] dat_o, + output rx_int_o, output tx_int_o, output tx_o, input rx_i, output baud_o); // Register Map localparam SUART_CLKDIV = 0; @@ -30,7 +31,7 @@ module simple_uart always @(posedge clk_i) if (rst_i) - clkdiv <= 0; + clkdiv <= CLKDIV_DEFAULT; else if (wb_wr) case(adr_i) SUART_CLKDIV : clkdiv <= dat_i[15:0]; diff --git a/fpga/usrp2/fifo/.gitignore b/fpga/usrp2/fifo/.gitignore index cba7efc8e..866f1faad 100644 --- a/fpga/usrp2/fifo/.gitignore +++ b/fpga/usrp2/fifo/.gitignore @@ -1 +1,3 @@ +*.vcd +*.lxt a.out diff --git a/fpga/usrp2/fifo/fifo19_to_fifo36.v b/fpga/usrp2/fifo/fifo19_to_fifo36.v index 5f9aeff9b..0e6bcea68 100644 --- a/fpga/usrp2/fifo/fifo19_to_fifo36.v +++ b/fpga/usrp2/fifo/fifo19_to_fifo36.v @@ -1,26 +1,31 @@ +// Parameter LE tells us if we are little-endian. +// Little-endian means send lower 16 bits first. +// Default is big endian (network order), send upper bits first. + module fifo19_to_fifo36 - (input clk, input reset, input clear, - input [18:0] f19_datain, - input f19_src_rdy_i, - output f19_dst_rdy_o, + #(parameter LE=0) + (input clk, input reset, input clear, + input [18:0] f19_datain, + input f19_src_rdy_i, + output f19_dst_rdy_o, - output [35:0] f36_dataout, - output f36_src_rdy_o, - input f36_dst_rdy_i, - output [31:0] debug - ); + output [35:0] f36_dataout, + output f36_src_rdy_o, + input f36_dst_rdy_i, + output [31:0] debug + ); - reg f36_sof, f36_eof, f36_occ; + reg f36_sof, f36_eof, f36_occ; - reg [1:0] state; - reg [15:0] dat0, dat1; + reg [1:0] state; + reg [15:0] dat0, dat1; - wire f19_sof = f19_datain[16]; - wire f19_eof = f19_datain[17]; - wire f19_occ = f19_datain[18]; + wire f19_sof = f19_datain[16]; + wire f19_eof = f19_datain[17]; + wire f19_occ = f19_datain[18]; - wire xfer_out = f36_src_rdy_o & f36_dst_rdy_i; + wire xfer_out = f36_src_rdy_o & f36_dst_rdy_i; always @(posedge clk) if(f19_src_rdy_i & ((state==0)|xfer_out)) @@ -68,7 +73,8 @@ module fifo19_to_fifo36 dat0 <= f19_datain; assign f19_dst_rdy_o = xfer_out | (state != 2); - assign f36_dataout = {f36_occ,f36_eof,f36_sof,dat0,dat1}; + assign f36_dataout = LE ? {f36_occ,f36_eof,f36_sof,dat1,dat0} : + {f36_occ,f36_eof,f36_sof,dat0,dat1}; assign f36_src_rdy_o = (state == 2); assign debug = state; diff --git a/fpga/usrp2/fifo/fifo36_to_fifo18.v b/fpga/usrp2/fifo/fifo36_to_fifo18.v deleted file mode 100644 index b636ab9ca..000000000 --- a/fpga/usrp2/fifo/fifo36_to_fifo18.v +++ /dev/null @@ -1,40 +0,0 @@ - -module fifo36_to_fifo18 - (input clk, input reset, input clear, - input [35:0] f36_datain, - input f36_src_rdy_i, - output f36_dst_rdy_o, - - output [17:0] f18_dataout, - output f18_src_rdy_o, - input f18_dst_rdy_i ); - - wire f36_sof = f36_datain[32]; - wire f36_eof = f36_datain[33]; - wire f36_occ = f36_datain[35:34]; - - reg phase; - - wire half_line = f36_eof & ((f36_occ==1)|(f36_occ==2)); - - assign f18_dataout[15:0] = phase ? f36_datain[15:0] : f36_datain[31:16]; - assign f18_dataout[16] = phase ? 0 : f36_sof; - assign f18_dataout[17] = phase ? f36_eof : half_line; - - assign f18_src_rdy_o = f36_src_rdy_i; - assign f36_dst_rdy_o = (phase | half_line) & f18_dst_rdy_i; - - wire f18_xfer = f18_src_rdy_o & f18_dst_rdy_i; - wire f36_xfer = f36_src_rdy_i & f36_dst_rdy_o; - - always @(posedge clk) - if(reset) - phase <= 0; - else if(f36_xfer) - phase <= 0; - else if(f18_xfer) - phase <= 1; - - -endmodule // fifo36_to_fifo18 - diff --git a/fpga/usrp2/fifo/fifo36_to_fifo19.v b/fpga/usrp2/fifo/fifo36_to_fifo19.v index de249aaeb..517a2a476 100644 --- a/fpga/usrp2/fifo/fifo36_to_fifo19.v +++ b/fpga/usrp2/fifo/fifo36_to_fifo19.v @@ -1,33 +1,38 @@ -module fifo36_to_fifo19 - (input clk, input reset, input clear, - input [35:0] f36_datain, - input f36_src_rdy_i, - output f36_dst_rdy_o, - - output [18:0] f19_dataout, - output f19_src_rdy_o, - input f19_dst_rdy_i ); +// Parameter LE tells us if we are little-endian. +// Little-endian means send lower 16 bits first. +// Default is big endian (network order), send upper bits first. +module fifo36_to_fifo19 + #(parameter LE=0) + (input clk, input reset, input clear, + input [35:0] f36_datain, + input f36_src_rdy_i, + output f36_dst_rdy_o, + + output [18:0] f19_dataout, + output f19_src_rdy_o, + input f19_dst_rdy_i ); + wire f36_sof = f36_datain[32]; wire f36_eof = f36_datain[33]; wire f36_occ = f36_datain[35:34]; - - reg phase; - - wire half_line = f36_eof & ((f36_occ==1)|(f36_occ==2)); - assign f19_dataout[15:0] = phase ? f36_datain[15:0] : f36_datain[31:16]; + reg phase; + + wire half_line = f36_eof & ((f36_occ==1)|(f36_occ==2)); + + assign f19_dataout[15:0] = (LE ^ phase) ? f36_datain[15:0] : f36_datain[31:16]; assign f19_dataout[16] = phase ? 0 : f36_sof; assign f19_dataout[17] = phase ? f36_eof : half_line; assign f19_dataout[18] = f19_dataout[17] & ((f36_occ==1)|(f36_occ==3)); assign f19_src_rdy_o = f36_src_rdy_i; assign f36_dst_rdy_o = (phase | half_line) & f19_dst_rdy_i; - - wire f19_xfer = f19_src_rdy_o & f19_dst_rdy_i; - wire f36_xfer = f36_src_rdy_i & f36_dst_rdy_o; - + + wire f19_xfer = f19_src_rdy_o & f19_dst_rdy_i; + wire f36_xfer = f36_src_rdy_i & f36_dst_rdy_o; + always @(posedge clk) if(reset) phase <= 0; @@ -36,6 +41,5 @@ module fifo36_to_fifo19 else if(f19_xfer) phase <= 1; - + endmodule // fifo36_to_fifo19 - diff --git a/fpga/usrp2/fifo/fifo36_to_ll8.v b/fpga/usrp2/fifo/fifo36_to_ll8.v index 0dee1dfc6..9604d0e38 100644 --- a/fpga/usrp2/fifo/fifo36_to_ll8.v +++ b/fpga/usrp2/fifo/fifo36_to_ll8.v @@ -55,6 +55,5 @@ module fifo36_to_ll8 assign advance = ll_src_rdy & ll_dst_rdy; assign f36_dst_rdy_o = advance & ((state==3)|ll_eof); - assign debug = state; endmodule // ll8_to_fifo36 diff --git a/fpga/usrp2/gpmc/.gitignore b/fpga/usrp2/gpmc/.gitignore new file mode 100644 index 000000000..3e14fa4f7 --- /dev/null +++ b/fpga/usrp2/gpmc/.gitignore @@ -0,0 +1,2 @@ +*.gif + diff --git a/fpga/usrp2/gpmc/Makefile.srcs b/fpga/usrp2/gpmc/Makefile.srcs new file mode 100644 index 000000000..bff6ae3e0 --- /dev/null +++ b/fpga/usrp2/gpmc/Makefile.srcs @@ -0,0 +1,20 @@ +# +# Copyright 2010 Ettus Research LLC +# + +################################################## +# SERDES Sources +################################################## +GPMC_SRCS = $(abspath $(addprefix $(BASE_DIR)/../gpmc/, \ +dbsm.v \ +edge_sync.v \ +fifo_to_gpmc_async.v \ +fifo_to_gpmc_sync.v \ +fifo_watcher.v \ +gpmc_async.v \ +gpmc_sync.v \ +gpmc_to_fifo_async.v \ +gpmc_to_fifo_sync.v \ +gpmc_wb.v \ +ram_to_fifo.v \ +)) diff --git a/fpga/usrp2/gpmc/burst_data_write.txt b/fpga/usrp2/gpmc/burst_data_write.txt new file mode 100644 index 000000000..3b5dfc785 --- /dev/null +++ b/fpga/usrp2/gpmc/burst_data_write.txt @@ -0,0 +1,16 @@ +# OMAP burst writes to FPGA + +CLK=0,nWE=1,nCS=1,nOE=1,DATA=Z. +CLK=1. +CLK=0,nWE=0,nCS=0,DATA=WR_DATA1. +CLK=1. +CLK=0,nWE=0,nCS=0,DATA=WR_DATA2. +CLK=1. +CLK=0,nWE=0,nCS=0,DATA=WR_DATA3. +CLK=1. +CLK=0,nWE=0,nCS=0,DATA=WR_DATA4. +CLK=1. +CLK=0,nWE=1,nCS=1,DATA=Z. +CLK=1. + + diff --git a/fpga/usrp2/gpmc/dbsm.v b/fpga/usrp2/gpmc/dbsm.v new file mode 100644 index 000000000..530af7205 --- /dev/null +++ b/fpga/usrp2/gpmc/dbsm.v @@ -0,0 +1,80 @@ + +module bsm + (input clk, input reset, input clear, + input write_done, + input read_done, + output readable, + output writeable); + + reg state; + localparam ST_WRITEABLE = 0; + localparam ST_READABLE = 1; + + always @(posedge clk) + if(reset | clear) + state <= ST_WRITEABLE; + else + case(state) + ST_WRITEABLE : + if(write_done) + state <= ST_READABLE; + ST_READABLE : + if(read_done) + state <= ST_WRITEABLE; + endcase // case (state) + + assign readable = (state == ST_READABLE); + assign writeable = (state == ST_WRITEABLE); + +endmodule // bsm + +module dbsm + (input clk, input reset, input clear, + output reg read_sel, output read_ready, input read_done, + output reg write_sel, output write_ready, input write_done); + + localparam NUM_BUFS = 2; + + wire [NUM_BUFS-1:0] readable, writeable, read_done_buf, write_done_buf; + + // Two of these buffer state machines + genvar i; + generate + for(i=0;i<NUM_BUFS;i=i+1) + begin : BSMS + bsm bsm(.clk(clk), .reset(reset), .clear(clear), + .write_done((write_sel == i) & write_done), + .read_done((read_sel == i) & read_done), + .readable(readable[i]), .writeable(writeable[i])); + end + endgenerate + + reg full; + + always @(posedge clk) + if(reset | clear) + begin + write_sel <= 0; + full <= 0; + end + else + if(write_done & writeable[write_sel]) + if(write_sel ==(NUM_BUFS-1)) + write_sel <= 0; + else + write_sel <= write_sel + 1; + + always @(posedge clk) + if(reset | clear) + read_sel <= 0; + else + if(read_done & readable[read_sel]) + if(read_sel==(NUM_BUFS-1)) + read_sel <= 0; + else + read_sel <= read_sel + 1; + + assign write_ready = writeable[write_sel]; + assign read_ready = readable[read_sel]; + +endmodule // dbsm diff --git a/fpga/usrp2/gpmc/edge_sync.v b/fpga/usrp2/gpmc/edge_sync.v new file mode 100644 index 000000000..5d9417c08 --- /dev/null +++ b/fpga/usrp2/gpmc/edge_sync.v @@ -0,0 +1,22 @@ + + +module edge_sync + #(parameter POSEDGE = 1) + (input clk, + input rst, + input sig, + output trig); + + reg [1:0] delay; + + always @(posedge clk) + if(rst) + delay <= 2'b00; + else + delay <= {delay[0],sig}; + + assign trig = POSEDGE ? (delay==2'b01) : (delay==2'b10); + +endmodule // edge_sync + + diff --git a/fpga/usrp2/gpmc/fifo_to_gpmc_async.v b/fpga/usrp2/gpmc/fifo_to_gpmc_async.v new file mode 100644 index 000000000..cf8b6e861 --- /dev/null +++ b/fpga/usrp2/gpmc/fifo_to_gpmc_async.v @@ -0,0 +1,37 @@ + +// Assumes an asynchronous GPMC cycle +// If a packet bigger or smaller than we are told is sent, behavior is undefined. +// If dst_rdy_i is low when we get data, behavior is undefined and we signal bus error. +// If there is a bus error, we should be reset + +module fifo_to_gpmc_async + (input clk, input reset, input clear, + input [17:0] data_i, input src_rdy_i, output dst_rdy_o, + output [15:0] EM_D, input EM_NCS, input EM_NOE, + input [15:0] frame_len); + + // Synchronize the async control signals + reg [2:0] cs_del, oe_del; + reg [15:0] counter; + + always @(posedge clk) + if(reset) + begin + cs_del <= 3'b11; + oe_del <= 3'b11; + end + else + begin + cs_del <= { cs_del[1:0], EM_NCS }; + oe_del <= { oe_del[1:0], EM_NOE }; + end + + wire do_read = ( (~cs_del[1] | ~cs_del[2]) & (oe_del[1:0] == 2'b01)); // change output on trailing edge + wire first_read = (counter == 0); + wire last_read = ((counter+1) == frame_len); + + assign EM_D = data_i[15:0]; + + assign dst_rdy_o = do_read; + +endmodule // fifo_to_gpmc_async diff --git a/fpga/usrp2/gpmc/fifo_to_gpmc_sync.v b/fpga/usrp2/gpmc/fifo_to_gpmc_sync.v new file mode 100644 index 000000000..ef59d7137 --- /dev/null +++ b/fpga/usrp2/gpmc/fifo_to_gpmc_sync.v @@ -0,0 +1,26 @@ + +// Assumes a GPMC cycle with GPMC clock, as in the timing diagrams +// If a packet bigger or smaller than we are told is sent, behavior is undefined. +// If dst_rdy_i is low when we get data, behavior is undefined and we signal bus error. +// If there is a bus error, we should be reset + +module fifo_to_gpmc_sync + (input arst, + input [17:0] data_i, input src_rdy_i, output dst_rdy_o, + input EM_CLK, output [15:0] EM_D, input EM_NCS, input EM_NOE, + output fifo_ready, + output reg bus_error); + + assign EM_D = data_i[15:0]; + wire read_access = ~EM_NCS & ~EM_NOE; + + assign dst_rdy_o = read_access; + + always @(posedge EM_CLK or posedge arst) + if(arst) + bus_error <= 0; + else if(dst_rdy_o & ~src_rdy_i) + bus_error <= 1; + + +endmodule // fifo_to_gpmc_sync diff --git a/fpga/usrp2/gpmc/fifo_watcher.v b/fpga/usrp2/gpmc/fifo_watcher.v new file mode 100644 index 000000000..fe4e35de3 --- /dev/null +++ b/fpga/usrp2/gpmc/fifo_watcher.v @@ -0,0 +1,56 @@ + + +module fifo_watcher + (input clk, input reset, input clear, + input src_rdy1, input dst_rdy1, input sof1, input eof1, + input src_rdy2, input dst_rdy2, input sof2, input eof2, + output reg have_packet, output [15:0] length, output reg bus_error, + output [31:0] debug); + + wire write = src_rdy1 & dst_rdy1 & eof1; + wire read = src_rdy2 & dst_rdy2 & eof2; + wire have_packet_int; + reg [15:0] counter; + wire [4:0] pkt_count; + assign debug = pkt_count; + + fifo_short #(.WIDTH(16)) frame_lengths + (.clk(clk), .reset(reset), .clear(clear), + .datain(counter), .src_rdy_i(write), .dst_rdy_o(), + .dataout(length), .src_rdy_o(have_packet_int), .dst_rdy_i(read), + .occupied(pkt_count), .space()); + + always @(posedge clk) + if(reset | clear) + counter <= 1; // Start at 1 + else if(src_rdy1 & dst_rdy1) + if(eof1) + counter <= 1; + else + counter <= counter + 1; + + always @(posedge clk) + if(reset | clear) + bus_error <= 0; + else if(dst_rdy2 & ~src_rdy2) + bus_error <= 1; + else if(read & ~have_packet_int) + bus_error <= 1; + + reg in_packet; + always @(posedge clk) + if(reset | clear) + have_packet <= 0; + else + have_packet <= (have_packet_int & ~in_packet) | (pkt_count>1) ; + + always @(posedge clk) + if(reset | clear) + in_packet <= 0; + else if(src_rdy2 & dst_rdy2) + if(eof2) + in_packet <= 0; + else + in_packet <= 1; + +endmodule // fifo_watcher diff --git a/fpga/usrp2/gpmc/gpmc_async.v b/fpga/usrp2/gpmc/gpmc_async.v new file mode 100644 index 000000000..23bad56ae --- /dev/null +++ b/fpga/usrp2/gpmc/gpmc_async.v @@ -0,0 +1,130 @@ +////////////////////////////////////////////////////////////////////////////////// + +module gpmc_async + #(parameter TXFIFOSIZE = 11, parameter RXFIFOSIZE = 11) + (// GPMC signals + input arst, + input EM_CLK, inout [15:0] EM_D, input [10:1] EM_A, input [1:0] EM_NBE, + input EM_WAIT0, input EM_NCS4, input EM_NCS6, input EM_NWE, input EM_NOE, + + // GPIOs for FIFO signalling + output rx_have_data, output tx_have_space, output reg bus_error, input bus_reset, + + // Wishbone signals + input wb_clk, input wb_rst, + output [10:0] wb_adr_o, output [15:0] wb_dat_mosi, input [15:0] wb_dat_miso, + output [1:0] wb_sel_o, output wb_cyc_o, output wb_stb_o, output wb_we_o, input wb_ack_i, + + // FIFO interface + input fifo_clk, input fifo_rst, input clear_tx, input clear_rx, + output [35:0] tx_data_o, output tx_src_rdy_o, input tx_dst_rdy_i, + input [35:0] rx_data_i, input rx_src_rdy_i, output rx_dst_rdy_o, + + input [15:0] tx_frame_len, output [15:0] rx_frame_len, + + output [31:0] debug + ); + + wire EM_output_enable = (~EM_NOE & (~EM_NCS4 | ~EM_NCS6)); + wire [15:0] EM_D_fifo; + wire [15:0] EM_D_wb; + + assign EM_D = ~EM_output_enable ? 16'bz : ~EM_NCS4 ? EM_D_fifo : EM_D_wb; + + wire bus_error_tx, bus_error_rx; + + always @(posedge fifo_clk) + if(fifo_rst | clear_tx | clear_rx) + bus_error <= 0; + else + bus_error <= bus_error_tx | bus_error_rx; + + // CS4 is RAM_2PORT for DATA PATH (high-speed data) + // Writes go into one RAM, reads come from the other + // CS6 is for CONTROL PATH (wishbone) + + // //////////////////////////////////////////// + // TX Data Path + + wire [17:0] tx18_data, tx18b_data; + wire tx18_src_rdy, tx18_dst_rdy, tx18b_src_rdy, tx18b_dst_rdy; + wire [15:0] tx_fifo_space; + wire [35:0] tx36_data; + wire tx36_src_rdy, tx36_dst_rdy; + + gpmc_to_fifo_async gpmc_to_fifo_async + (.EM_D(EM_D), .EM_NBE(EM_NBE), .EM_NCS(EM_NCS4), .EM_NWE(EM_NWE), + .fifo_clk(fifo_clk), .fifo_rst(fifo_rst), .clear(clear_tx), + .data_o(tx18_data), .src_rdy_o(tx18_src_rdy), .dst_rdy_i(tx18_dst_rdy), + .frame_len(tx_frame_len), .fifo_space(tx_fifo_space), .fifo_ready(tx_have_space), + .bus_error(bus_error_tx) ); + + fifo_cascade #(.WIDTH(18), .SIZE(10)) tx_fifo + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx), + .datain(tx18_data), .src_rdy_i(tx18_src_rdy), .dst_rdy_o(tx18_dst_rdy), .space(tx_fifo_space), + .dataout(tx18b_data), .src_rdy_o(tx18b_src_rdy), .dst_rdy_i(tx18b_dst_rdy), .occupied()); + + fifo19_to_fifo36 #(.LE(1)) f19_to_f36 // Little endian because ARM is LE + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx), + .f19_datain({1'b0,tx18b_data}), .f19_src_rdy_i(tx18b_src_rdy), .f19_dst_rdy_o(tx18b_dst_rdy), + .f36_dataout(tx36_data), .f36_src_rdy_o(tx36_src_rdy), .f36_dst_rdy_i(tx36_dst_rdy)); + + fifo_cascade #(.WIDTH(36), .SIZE(TXFIFOSIZE)) tx_fifo36 + (.clk(wb_clk), .reset(wb_rst), .clear(clear_tx), + .datain(tx36_data), .src_rdy_i(tx36_src_rdy), .dst_rdy_o(tx36_dst_rdy), + .dataout(tx_data_o), .src_rdy_o(tx_src_rdy_o), .dst_rdy_i(tx_dst_rdy_i)); + + // //////////////////////////////////////////// + // RX Data Path + + wire [17:0] rx18_data, rx18b_data; + wire rx18_src_rdy, rx18_dst_rdy, rx18b_src_rdy, rx18b_dst_rdy; + wire [15:0] rx_fifo_space; + wire [35:0] rx36_data; + wire rx36_src_rdy, rx36_dst_rdy; + wire dummy; + + fifo_cascade #(.WIDTH(36), .SIZE(RXFIFOSIZE)) rx_fifo36 + (.clk(wb_clk), .reset(wb_rst), .clear(clear_rx), + .datain(rx_data_i), .src_rdy_i(rx_src_rdy_i), .dst_rdy_o(rx_dst_rdy_o), + .dataout(rx36_data), .src_rdy_o(rx36_src_rdy), .dst_rdy_i(rx36_dst_rdy)); + + fifo36_to_fifo19 #(.LE(1)) f36_to_f19 // Little endian because ARM is LE + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx), + .f36_datain(rx36_data), .f36_src_rdy_i(rx36_src_rdy), .f36_dst_rdy_o(rx36_dst_rdy), + .f19_dataout({dummy,rx18_data}), .f19_src_rdy_o(rx18_src_rdy), .f19_dst_rdy_i(rx18_dst_rdy) ); + + fifo_cascade #(.WIDTH(18), .SIZE(12)) rx_fifo + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx), + .datain(rx18_data), .src_rdy_i(rx18_src_rdy), .dst_rdy_o(rx18_dst_rdy), .space(rx_fifo_space), + .dataout(rx18b_data), .src_rdy_o(rx18b_src_rdy), .dst_rdy_i(rx18b_dst_rdy), .occupied()); + + fifo_to_gpmc_async fifo_to_gpmc_async + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx), + .data_i(rx18b_data), .src_rdy_i(rx18b_src_rdy), .dst_rdy_o(rx18b_dst_rdy), + .EM_D(EM_D_fifo), .EM_NCS(EM_NCS4), .EM_NOE(EM_NOE), + .frame_len(rx_frame_len) ); + + wire [31:0] pkt_count; + + fifo_watcher fifo_watcher + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx), + .src_rdy1(rx18_src_rdy), .dst_rdy1(rx18_dst_rdy), .sof1(rx18_data[16]), .eof1(rx18_data[17]), + .src_rdy2(rx18b_src_rdy), .dst_rdy2(rx18b_dst_rdy), .sof2(rx18b_data[16]), .eof2(rx18b_data[17]), + .have_packet(rx_have_data), .length(rx_frame_len), .bus_error(bus_error_rx), + .debug(pkt_count)); + + // //////////////////////////////////////////// + // Control path on CS6 + + gpmc_wb gpmc_wb + (.EM_CLK(EM_CLK), .EM_D_in(EM_D), .EM_D_out(EM_D_wb), .EM_A(EM_A), .EM_NBE(EM_NBE), + .EM_NCS(EM_NCS6), .EM_NWE(EM_NWE), .EM_NOE(EM_NOE), + .wb_clk(wb_clk), .wb_rst(wb_rst), + .wb_adr_o(wb_adr_o), .wb_dat_mosi(wb_dat_mosi), .wb_dat_miso(wb_dat_miso), + .wb_sel_o(wb_sel_o), .wb_cyc_o(wb_cyc_o), .wb_stb_o(wb_stb_o), .wb_we_o(wb_we_o), + .wb_ack_i(wb_ack_i) ); + + assign debug = pkt_count; + +endmodule // gpmc_async diff --git a/fpga/usrp2/gpmc/gpmc_sync.v b/fpga/usrp2/gpmc/gpmc_sync.v new file mode 100644 index 000000000..61c54a793 --- /dev/null +++ b/fpga/usrp2/gpmc/gpmc_sync.v @@ -0,0 +1,108 @@ +////////////////////////////////////////////////////////////////////////////////// + +module gpmc_sync + (// GPMC signals + input arst, + input EM_CLK, inout [15:0] EM_D, input [10:1] EM_A, input [1:0] EM_NBE, + input EM_WAIT0, input EM_NCS4, input EM_NCS6, input EM_NWE, input EM_NOE, + + // GPIOs for FIFO signalling + output rx_have_data, output tx_have_space, output bus_error, input bus_reset, + + // Wishbone signals + input wb_clk, input wb_rst, + output [10:0] wb_adr_o, output [15:0] wb_dat_mosi, input [15:0] wb_dat_miso, + output [1:0] wb_sel_o, output wb_cyc_o, output wb_stb_o, output wb_we_o, input wb_ack_i, + + // FIFO interface + input fifo_clk, input fifo_rst, + output [35:0] tx_data_o, output tx_src_rdy_o, input tx_dst_rdy_i, + input [35:0] rx_data_i, input rx_src_rdy_i, output rx_dst_rdy_o, + + output [31:0] debug + ); + + wire EM_output_enable = (~EM_NOE & (~EM_NCS4 | ~EM_NCS6)); + wire [15:0] EM_D_fifo; + wire [15:0] EM_D_wb; + + assign EM_D = ~EM_output_enable ? 16'bz : ~EM_NCS4 ? EM_D_fifo : EM_D_wb; + + wire bus_error_tx, bus_error_rx; + assign bus_error = bus_error_tx | bus_error_rx; + + // CS4 is RAM_2PORT for DATA PATH (high-speed data) + // Writes go into one RAM, reads come from the other + // CS6 is for CONTROL PATH (wishbone) + + // //////////////////////////////////////////// + // TX Data Path + + wire [17:0] tx18_data, tx18b_data; + wire tx18_src_rdy, tx18_dst_rdy, tx18b_src_rdy, tx18b_dst_rdy; + wire [15:0] tx_fifo_space, tx_frame_len; + + assign tx_frame_len = 10; + + gpmc_to_fifo_sync gpmc_to_fifo_sync + (.arst(arst), + .EM_CLK(EM_CLK), .EM_D(EM_D), .EM_NBE(EM_NBE), .EM_NCS(EM_NCS4), .EM_NWE(EM_NWE), + .data_o(tx18_data), .src_rdy_o(tx18_src_rdy), .dst_rdy_i(tx18_dst_rdy), + .frame_len(tx_frame_len), .fifo_space(tx_fifo_space), .fifo_ready(tx_have_space), + .bus_error(bus_error_tx) ); + + fifo_2clock_cascade #(.WIDTH(18), .SIZE(4)) tx_fifo + (.wclk(EM_CLK), .datain(tx18_data), + .src_rdy_i(tx18_src_rdy), .dst_rdy_o(tx18_dst_rdy), .space(tx_fifo_space), + .rclk(fifo_clk), .dataout(tx18b_data), + .src_rdy_o(tx18b_src_rdy), .dst_rdy_i(tx18b_dst_rdy), .occupied(), .arst(arst)); + + fifo19_to_fifo36 #(.LE(1)) f19_to_f36 // Little endian because ARM is LE + (.clk(fifo_clk), .reset(fifo_rst), .clear(0), + .f19_datain({1'b0,tx18b_data}), .f19_src_rdy_i(tx18b_src_rdy), .f19_dst_rdy_o(tx18b_dst_rdy), + .f36_dataout(tx_data_o), .f36_src_rdy_o(tx_src_rdy_o), .f36_dst_rdy_i(tx_dst_rdy_i)); + + // //////////////////////////////////////////// + // RX Data Path + + wire [17:0] rx18_data, rx18b_data; + wire rx18_src_rdy, rx18_dst_rdy, rx18b_src_rdy, rx18b_dst_rdy; + wire [15:0] rx_fifo_space, rx_frame_len; + wire dummy; + + fifo36_to_fifo19 #(.LE(1)) f36_to_f19 // Little endian because ARM is LE + (.clk(fifo_clk), .reset(fifo_rst), .clear(0), + .f36_datain(rx_data_i), .f36_src_rdy_i(rx_src_rdy_i), .f36_dst_rdy_o(rx_dst_rdy_o), + .f19_dataout({dummy,rx18_data}), .f19_src_rdy_o(rx18_src_rdy), .f19_dst_rdy_i(rx18_dst_rdy) ); + + fifo_2clock_cascade #(.WIDTH(18), .SIZE(10)) rx_fifo + (.wclk(fifo_clk), .datain(rx18_data), + .src_rdy_i(rx18_src_rdy), .dst_rdy_o(rx18_dst_rdy), .space(rx_fifo_space), + .rclk(EM_CLK), .dataout(rx18b_data), + .src_rdy_o(rx18b_src_rdy), .dst_rdy_i(rx18b_dst_rdy), .occupied(), .arst(arst)); + + fifo_to_gpmc_sync fifo_to_gpmc_sync + (.arst(arst), + .data_i(rx18b_data), .src_rdy_i(rx18b_src_rdy), .dst_rdy_o(rx18b_dst_rdy), + .EM_CLK(EM_CLK), .EM_D(EM_D_fifo), .EM_NCS(EM_NCS4), .EM_NOE(EM_NOE), + .fifo_ready(rx_have_data) ); + + fifo_watcher fifo_watcher + (.clk(fifo_clk), .reset(fifo_rst), .clear(0), + .src_rdy(rx18_src_rdy), .dst_rdy(rx18_dst_rdy), .sof(rx18_data[16]), .eof(rx18_data[17]), + .have_packet(), .length(), .next() ); + + // //////////////////////////////////////////// + // Control path on CS6 + + gpmc_wb gpmc_wb + (.EM_CLK(EM_CLK), .EM_D_in(EM_D), .EM_D_out(EM_D_wb), .EM_A(EM_A), .EM_NBE(EM_NBE), + .EM_NCS(EM_NCS6), .EM_NWE(EM_NWE), .EM_NOE(EM_NOE), + .wb_clk(wb_clk), .wb_rst(wb_rst), + .wb_adr_o(wb_adr_o), .wb_dat_mosi(wb_dat_mosi), .wb_dat_miso(wb_dat_miso), + .wb_sel_o(wb_sel_o), .wb_cyc_o(wb_cyc_o), .wb_stb_o(wb_stb_o), .wb_we_o(wb_we_o), + .wb_ack_i(wb_ack_i) ); + + assign debug = 0; + +endmodule // gpmc_sync diff --git a/fpga/usrp2/gpmc/gpmc_to_fifo_async.v b/fpga/usrp2/gpmc/gpmc_to_fifo_async.v new file mode 100644 index 000000000..55c0cef50 --- /dev/null +++ b/fpga/usrp2/gpmc/gpmc_to_fifo_async.v @@ -0,0 +1,68 @@ + +module gpmc_to_fifo_async + (input [15:0] EM_D, input [1:0] EM_NBE, input EM_NCS, input EM_NWE, + + input fifo_clk, input fifo_rst, input clear, + output reg [17:0] data_o, output reg src_rdy_o, input dst_rdy_i, + + input [15:0] frame_len, input [15:0] fifo_space, output reg fifo_ready, + output reg bus_error ); + + reg [15:0] counter; + // Synchronize the async control signals + reg [1:0] cs_del, we_del; + always @(posedge fifo_clk) + if(fifo_rst) + begin + cs_del <= 2'b11; + we_del <= 2'b11; + end + else + begin + cs_del <= { cs_del[0], EM_NCS }; + we_del <= { we_del[0], EM_NWE }; + end + + wire do_write = (~cs_del[0] & (we_del == 2'b10)); + wire first_write = (counter == 0); + wire last_write = ((counter+1) == frame_len); + + always @(posedge fifo_clk) + if(do_write) + begin + data_o[15:0] <= EM_D; + data_o[16] <= first_write; + data_o[17] <= last_write; + // no byte writes data_o[18] <= |EM_NBE; // mark half full if either is not enabled FIXME + end + + always @(posedge fifo_clk) + if(fifo_rst | clear) + src_rdy_o <= 0; + else if(do_write) + src_rdy_o <= 1; + else + src_rdy_o <= 0; // Assume it was taken + + always @(posedge fifo_clk) + if(fifo_rst | clear) + counter <= 0; + else if(do_write) + if(last_write) + counter <= 0; + else + counter <= counter + 1; + + always @(posedge fifo_clk) + if(fifo_rst | clear) + fifo_ready <= 0; + else + fifo_ready <= /* first_write & */ (fifo_space > 16'd1023); + + always @(posedge fifo_clk) + if(fifo_rst | clear) + bus_error <= 0; + else if(src_rdy_o & ~dst_rdy_i) + bus_error <= 1; + +endmodule // gpmc_to_fifo_async diff --git a/fpga/usrp2/gpmc/gpmc_to_fifo_sync.v b/fpga/usrp2/gpmc/gpmc_to_fifo_sync.v new file mode 100644 index 000000000..688de0e17 --- /dev/null +++ b/fpga/usrp2/gpmc/gpmc_to_fifo_sync.v @@ -0,0 +1,57 @@ + +// Assumes a GPMC cycle with GPMC clock, as in the timing diagrams +// If a packet bigger or smaller than we are told is sent, behavior is undefined. +// If dst_rdy_i is low when we get data, behavior is undefined and we signal bus error. +// If there is a bus error, we should be reset + +module gpmc_to_fifo_sync + (input arst, + input EM_CLK, input [15:0] EM_D, input [1:0] EM_NBE, + input EM_NCS, input EM_NWE, + output reg [17:0] data_o, output reg src_rdy_o, input dst_rdy_i, + input [15:0] frame_len, input [15:0] fifo_space, output fifo_ready, + output reg bus_error); + + reg [10:0] counter; + wire first_write = (counter == 0); + wire last_write = ((counter+1) == frame_len); + wire do_write = ~EM_NCS & ~EM_NWE; + + always @(posedge EM_CLK or posedge arst) + if(arst) + data_o <= 0; + else if(do_write) + begin + data_o[15:0] <= EM_D; + data_o[16] <= first_write; + data_o[17] <= last_write; + // no byte writes data_o[18] <= |EM_NBE; // mark half full if either is not enabled FIXME + end + + always @(posedge EM_CLK or posedge arst) + if(arst) + src_rdy_o <= 0; + else if(do_write & ~bus_error) // Don't put junk in if there is a bus error + src_rdy_o <= 1; + else + src_rdy_o <= 0; // Assume it was taken, ignore dst_rdy_i + + always @(posedge EM_CLK or posedge arst) + if(arst) + counter <= 0; + else if(do_write) + if(last_write) + counter <= 0; + else + counter <= counter + 1; + + assign fifo_ready = first_write & (fifo_space > frame_len); + + always @(posedge EM_CLK or posedge arst) + if(arst) + bus_error <= 0; + else if(src_rdy_o & ~dst_rdy_i) + bus_error <= 1; + // must be reset to make the error go away + +endmodule // gpmc_to_fifo_sync diff --git a/fpga/usrp2/gpmc/gpmc_wb.v b/fpga/usrp2/gpmc/gpmc_wb.v new file mode 100644 index 000000000..db6fbc6e9 --- /dev/null +++ b/fpga/usrp2/gpmc/gpmc_wb.v @@ -0,0 +1,57 @@ + + +module gpmc_wb + (input EM_CLK, input [15:0] EM_D_in, output [15:0] EM_D_out, input [10:1] EM_A, input [1:0] EM_NBE, + input EM_NCS, input EM_NWE, input EM_NOE, + + input wb_clk, input wb_rst, + output reg [10:0] wb_adr_o, output reg [15:0] wb_dat_mosi, input [15:0] wb_dat_miso, + output reg [1:0] wb_sel_o, output wb_cyc_o, output reg wb_stb_o, output reg wb_we_o, input wb_ack_i); + + // //////////////////////////////////////////// + // Control Path, Wishbone bus bridge (wb master) + reg [1:0] cs_del, we_del, oe_del; + + // Synchronize the async control signals + always @(posedge wb_clk) + begin + cs_del <= { cs_del[0], EM_NCS }; + we_del <= { we_del[0], EM_NWE }; + oe_del <= { oe_del[0], EM_NOE }; + end + + always @(posedge wb_clk) + if(cs_del == 2'b10) // Falling Edge + wb_adr_o <= { EM_A, 1'b0 }; + + always @(posedge wb_clk) + if(we_del == 2'b10) // Falling Edge + begin + wb_dat_mosi <= EM_D_in; + wb_sel_o <= ~EM_NBE; + end + + reg [15:0] EM_D_hold; + + always @(posedge wb_clk) + if(wb_ack_i) + EM_D_hold <= wb_dat_miso; + + assign EM_D_out = wb_ack_i ? wb_dat_miso : EM_D_hold; + + assign wb_cyc_o = wb_stb_o; + + always @(posedge wb_clk) + if(~cs_del[0] & (we_del == 2'b10) ) + wb_we_o <= 1; + else if(wb_ack_i) // Turn off we when done. Could also use we_del[0], others... + wb_we_o <= 0; + + // FIXME should this look at cs_del[1]? + always @(posedge wb_clk) + if(~cs_del[0] & ((we_del == 2'b10) | (oe_del == 2'b10))) + wb_stb_o <= 1; + else if(wb_ack_i) + wb_stb_o <= 0; + +endmodule // gpmc_wb diff --git a/fpga/usrp2/gpmc/make_timing_diag b/fpga/usrp2/gpmc/make_timing_diag new file mode 100755 index 000000000..03166ad35 --- /dev/null +++ b/fpga/usrp2/gpmc/make_timing_diag @@ -0,0 +1,6 @@ +#!/bin/sh +drawtiming -o single_data_write.gif single_data_write.txt +drawtiming -o single_data_read.gif single_data_read.txt +drawtiming -o burst_data_write.gif burst_data_write.txt +#drawtiming -o burst_data_read.gif burst_data_read.txt + diff --git a/fpga/usrp2/gpmc/ram_to_fifo.v b/fpga/usrp2/gpmc/ram_to_fifo.v new file mode 100644 index 000000000..8549dcc35 --- /dev/null +++ b/fpga/usrp2/gpmc/ram_to_fifo.v @@ -0,0 +1,46 @@ + + +module ram_to_fifo + (input clk, input reset, + input [10:0] read_length, // From the dbsm (?) + output read_en, output reg [8:0] read_addr, input [31:0] read_data, input read_ready, output read_done, + output [35:0] data_o, output src_rdy_o, input dst_rdy_i); + + // read_length/2 = number of 32 bit lines, numbered 0 through read_length/2-1 + wire [8:0] last_line = (read_length[10:1]-1); + + reg read_phase, sop; + + assign read_en = (read_phase == 0) | dst_rdy_i; + assign src_rdy_o = (read_phase == 1); + + always @(posedge clk) + if(reset) + begin + read_addr <= 0; + read_phase <= 0; + sop <= 1; + end + else + if(read_phase == 0) + begin + read_addr <= read_ready; + read_phase <= read_ready; + end + else if(dst_rdy_i) + begin + sop <= 0; + if(read_addr == last_line) + begin + read_addr <= 0; + read_phase <= 0; + end + else + read_addr <= read_addr + 1; + end + + assign read_done = (read_phase == 1) & (read_addr == last_line) & dst_rdy_i; + wire eop = (read_addr == last_line); + assign data_o = { 2'b00, eop, sop, read_data }; + +endmodule // ram_to_fifo diff --git a/fpga/usrp2/gpmc/single_data_read.txt b/fpga/usrp2/gpmc/single_data_read.txt new file mode 100644 index 000000000..1dc0e3a78 --- /dev/null +++ b/fpga/usrp2/gpmc/single_data_read.txt @@ -0,0 +1,12 @@ +# OMAP writes to FPGA +# initialize the signals +CLK=0,nWE=1,nCS=1,nOE=1,DATA=Z. +CLK=1. +CLK=0,nOE=0,nCS=0,DATA=RD_DATA. +CLK=1. +CLK=0. +CLK=1. +CLK=0,nOE=1,nCS=1,DATA=Z. +CLK=1. + + diff --git a/fpga/usrp2/gpmc/single_data_write.txt b/fpga/usrp2/gpmc/single_data_write.txt new file mode 100644 index 000000000..287e3e2c1 --- /dev/null +++ b/fpga/usrp2/gpmc/single_data_write.txt @@ -0,0 +1,10 @@ +# OMAP writes to FPGA +# initialize the signals +CLK=0,nWE=1,nCS=1,nOE=1,DATA=Z. +CLK=1. +CLK=0,nWE=0,nCS=0,DATA=WR_DATA. +CLK=1. +CLK=0,nWE=1,nCS=1,DATA=Z. +CLK=1. + + diff --git a/fpga/usrp2/models/gpmc_model_async.v b/fpga/usrp2/models/gpmc_model_async.v new file mode 100644 index 000000000..beeaee028 --- /dev/null +++ b/fpga/usrp2/models/gpmc_model_async.v @@ -0,0 +1,130 @@ +`timescale 1ps/1ps + +module gpmc_model_async + (output EM_CLK, inout [15:0] EM_D, output reg [10:1] EM_A, output reg [1:0] EM_NBE, + output reg EM_WAIT0, output reg EM_NCS4, output reg EM_NCS6, + output reg EM_NWE, output reg EM_NOE ); + + assign EM_CLK = 0; + reg [15:0] EM_D_int; + assign EM_D = EM_D_int; + + initial + begin + EM_A <= 10'bz; + EM_NBE <= 2'b11; + EM_NWE <= 1; + EM_NOE <= 1; + EM_NCS4 <= 1; + EM_NCS6 <= 1; + EM_D_int <= 16'bz; + EM_WAIT0 <= 0; // FIXME this is actually an input + end + + task GPMC_Write; + input ctrl; + input [10:0] addr; + input [15:0] data; + begin + #23000; + EM_A <= addr[10:1]; + EM_D_int <= data; + #20100; + if(ctrl) + EM_NCS6 <= 0; + else + EM_NCS4 <= 0; + #14000; + EM_NWE <= 0; + #77500; + EM_NCS4 <= 1; + EM_NCS6 <= 1; + //#1.5; + EM_NWE <= 1; + #60000; + EM_A <= 10'bz; + EM_D_int <= 16'bz; + end + endtask // GPMC_Write + + task GPMC_Read; + input ctrl; + input [10:0] addr; + begin + #13000; + EM_A <= addr[10:1]; + #3000; + if(ctrl) + EM_NCS6 <= 0; + else + EM_NCS4 <= 0; + #14000; + EM_NOE <= 0; + #77500; + EM_NCS4 <= 1; + EM_NCS6 <= 1; + //#1.5; + $display("Data Read from GPMC: %X",EM_D); + EM_NOE <= 1; + #254000; + EM_A <= 10'bz; + end + endtask // GPMC_Read + + initial + begin + #1000000; + GPMC_Write(1,36,16'hF00D); + #1000000; + GPMC_Read(1,36); + #1000000; + GPMC_Write(0,0,16'h1234); + GPMC_Write(0,0,16'h5678); + GPMC_Write(0,0,16'h9abc); + GPMC_Write(0,0,16'hF00D); + GPMC_Write(0,0,16'hDEAD); + GPMC_Write(0,0,16'hDEAD); + GPMC_Write(0,0,16'hDEAD); + GPMC_Write(0,0,16'hDEAD); + GPMC_Write(0,0,16'hDEAD); + GPMC_Write(0,0,16'hDEAD); + #1000000; + GPMC_Write(0,0,16'h1234); + GPMC_Write(0,0,16'h5678); + GPMC_Write(0,0,16'h9abc); + GPMC_Write(0,0,16'hF00D); + GPMC_Write(0,0,16'hDEAD); + GPMC_Write(0,0,16'hDEAD); + GPMC_Write(0,0,16'hDEAD); + GPMC_Write(0,0,16'hDEAD); + GPMC_Write(0,0,16'hDEAD); + GPMC_Write(0,0,16'h9876); + #1000000; + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + #1000000; + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + GPMC_Read(0,0); + #1000000; + GPMC_Read(0,0); + #100000000; + $finish; + end + +endmodule // gpmc_model_async diff --git a/fpga/usrp2/models/gpmc_model_sync.v b/fpga/usrp2/models/gpmc_model_sync.v new file mode 100644 index 000000000..641720c15 --- /dev/null +++ b/fpga/usrp2/models/gpmc_model_sync.v @@ -0,0 +1,97 @@ + + +module gpmc_model_sync + (output reg EM_CLK, inout [15:0] EM_D, output reg [10:1] EM_A, output reg [1:0] EM_NBE, + output reg EM_WAIT0, output reg EM_NCS4, output reg EM_NCS6, + output reg EM_NWE, output reg EM_NOE ); + + reg [15:0] EM_D_int; + assign EM_D = EM_D_int; + + initial + begin + EM_CLK <= 0; + EM_A <= 10'bz; + EM_NBE <= 2'b11; + EM_NWE <= 1; + EM_NOE <= 1; + EM_NCS4 <= 1; + EM_NCS6 <= 1; + EM_D_int <= 16'bz; + EM_WAIT0 <= 0; // FIXME this is actually an input + end + + task GPMC_Write; + input ctrl; + input [10:0] addr; + input [15:0] data; + begin + EM_CLK <= 1; + #10; + EM_CLK <= 0; + EM_NWE <= 0; + if(ctrl) + EM_NCS6 <= 0; + else + EM_NCS4 <= 0; + EM_A <= addr[10:1]; + EM_D_int <= data; + #10; + EM_CLK <= 1; + #10; + EM_CLK <= 0; + EM_NWE <= 1; + EM_NCS4 <= 1; + EM_NCS6 <= 1; + EM_A <= 10'bz; + EM_D_int <= 16'bz; + #100; + end + endtask // GPMC_Write + + task GPMC_Read; + input ctrl; + input [10:0] addr; + begin + #1.3; + EM_A <= addr[10:1]; + #3; + if(ctrl) + EM_NCS6 <= 0; + else + EM_NCS4 <= 0; + #14; + EM_NOE <= 0; + #77.5; + EM_NCS4 <= 1; + EM_NCS6 <= 1; + //#1.5; + $display("Data Read from GPMC: %X",EM_D); + EM_NOE <= 1; + #254; + EM_A <= 10'bz; + end + endtask // GPMC_Read + + initial + begin + #1000; + GPMC_Write(1,36,16'hF00D); + #1000; + GPMC_Read(1,36); + #1000; + GPMC_Write(0,36,16'h1234); + GPMC_Write(0,38,16'h5678); + GPMC_Write(0,40,16'h9abc); + GPMC_Write(0,11'h2F4,16'hF00D); + GPMC_Write(0,11'h7FE,16'hDEAD); + GPMC_Write(0,11'h7FE,16'hDEAD); + GPMC_Write(0,11'h7FE,16'hDEAD); + GPMC_Write(0,11'h7FE,16'hDEAD); + GPMC_Write(0,11'h7FE,16'hDEAD); + GPMC_Write(0,11'h7FE,16'hDEAD); + #100000; + $finish; + end + +endmodule // gpmc_model diff --git a/fpga/usrp2/opencores/Makefile.srcs b/fpga/usrp2/opencores/Makefile.srcs index 30360a17d..1ccecf337 100644 --- a/fpga/usrp2/opencores/Makefile.srcs +++ b/fpga/usrp2/opencores/Makefile.srcs @@ -23,6 +23,5 @@ i2c/rtl/verilog/timescale.v \ spi/rtl/verilog/spi_clgen.v \ spi/rtl/verilog/spi_defines.v \ spi/rtl/verilog/spi_shift.v \ -spi/rtl/verilog/spi_top.v \ -spi/rtl/verilog/timescale.v \ +spi/rtl/verilog/spi_top16.v \ )) diff --git a/fpga/usrp2/opencores/spi/rtl/verilog/spi_clgen.v b/fpga/usrp2/opencores/spi/rtl/verilog/spi_clgen.v index 7bc4f6e5e..2d9c34f40 100644 --- a/fpga/usrp2/opencores/spi/rtl/verilog/spi_clgen.v +++ b/fpga/usrp2/opencores/spi/rtl/verilog/spi_clgen.v @@ -39,12 +39,9 @@ ////////////////////////////////////////////////////////////////////// `include "spi_defines.v" -`include "timescale.v" module spi_clgen (clk_in, rst, go, enable, last_clk, divider, clk_out, pos_edge, neg_edge); - parameter Tp = 1; - input clk_in; // input clock (system clock) input rst; // reset input enable; // clock enable @@ -68,40 +65,40 @@ module spi_clgen (clk_in, rst, go, enable, last_clk, divider, clk_out, pos_edge, assign cnt_one = cnt == {{`SPI_DIVIDER_LEN-1{1'b0}}, 1'b1}; // Counter counts half period - always @(posedge clk_in or posedge rst) + always @(posedge clk_in) begin if(rst) - cnt <= #Tp {`SPI_DIVIDER_LEN{1'b1}}; + cnt <= {`SPI_DIVIDER_LEN{1'b1}}; else begin if(!enable || cnt_zero) - cnt <= #Tp divider; + cnt <= divider; else - cnt <= #Tp cnt - {{`SPI_DIVIDER_LEN-1{1'b0}}, 1'b1}; + cnt <= cnt - {{`SPI_DIVIDER_LEN-1{1'b0}}, 1'b1}; end end // clk_out is asserted every other half period - always @(posedge clk_in or posedge rst) + always @(posedge clk_in) begin if(rst) - clk_out <= #Tp 1'b0; + clk_out <= 1'b0; else - clk_out <= #Tp (enable && cnt_zero && (!last_clk || clk_out)) ? ~clk_out : clk_out; + clk_out <= (enable && cnt_zero && (!last_clk || clk_out)) ? ~clk_out : clk_out; end // Pos and neg edge signals - always @(posedge clk_in or posedge rst) + always @(posedge clk_in) begin if(rst) begin - pos_edge <= #Tp 1'b0; - neg_edge <= #Tp 1'b0; + pos_edge <= 1'b0; + neg_edge <= 1'b0; end else begin - pos_edge <= #Tp (enable && !clk_out && cnt_one) || (!(|divider) && clk_out) || (!(|divider) && go && !enable); - neg_edge <= #Tp (enable && clk_out && cnt_one) || (!(|divider) && !clk_out && enable); + pos_edge <= (enable && !clk_out && cnt_one) || (!(|divider) && clk_out) || (!(|divider) && go && !enable); + neg_edge <= (enable && clk_out && cnt_one) || (!(|divider) && !clk_out && enable); end end endmodule diff --git a/fpga/usrp2/opencores/spi/rtl/verilog/spi_defines.v b/fpga/usrp2/opencores/spi/rtl/verilog/spi_defines.v index a6925918e..963a680a8 100644 --- a/fpga/usrp2/opencores/spi/rtl/verilog/spi_defines.v +++ b/fpga/usrp2/opencores/spi/rtl/verilog/spi_defines.v @@ -43,8 +43,8 @@ // low frequency of system clock this can be reduced. // Use SPI_DIVIDER_LEN for fine tuning theexact number. // -//`define SPI_DIVIDER_LEN_8 -`define SPI_DIVIDER_LEN_16 +`define SPI_DIVIDER_LEN_8 +//`define SPI_DIVIDER_LEN_16 //`define SPI_DIVIDER_LEN_24 //`define SPI_DIVIDER_LEN_32 @@ -66,9 +66,9 @@ // Use SPI_MAX_CHAR for fine tuning the exact number, when using // SPI_MAX_CHAR_32, SPI_MAX_CHAR_24, SPI_MAX_CHAR_16, SPI_MAX_CHAR_8. // -`define SPI_MAX_CHAR_128 +//`define SPI_MAX_CHAR_128 //`define SPI_MAX_CHAR_64 -//`define SPI_MAX_CHAR_32 +`define SPI_MAX_CHAR_32 //`define SPI_MAX_CHAR_24 //`define SPI_MAX_CHAR_16 //`define SPI_MAX_CHAR_8 @@ -137,7 +137,7 @@ `define SPI_TX_2 2 `define SPI_TX_3 3 `define SPI_CTRL 4 -`define SPI_DEVIDE 5 +`define SPI_DIVIDE 5 `define SPI_SS 6 // diff --git a/fpga/usrp2/opencores/spi/rtl/verilog/spi_shift.v b/fpga/usrp2/opencores/spi/rtl/verilog/spi_shift.v index b17ac8b1f..ac3bb3f48 100644 --- a/fpga/usrp2/opencores/spi/rtl/verilog/spi_shift.v +++ b/fpga/usrp2/opencores/spi/rtl/verilog/spi_shift.v @@ -39,15 +39,12 @@ ////////////////////////////////////////////////////////////////////// `include "spi_defines.v" -`include "timescale.v" module spi_shift (clk, rst, latch, byte_sel, len, lsb, go, pos_edge, neg_edge, rx_negedge, tx_negedge, tip, last, p_in, p_out, s_clk, s_in, s_out); - parameter Tp = 1; - input clk; // system clock input rst; // reset input [3:0] latch; // latch signal for storing the data in shift register @@ -89,149 +86,149 @@ module spi_shift (clk, rst, latch, byte_sel, len, lsb, go, assign tx_clk = (tx_negedge ? neg_edge : pos_edge) && !last; // Character bit counter - always @(posedge clk or posedge rst) + always @(posedge clk) begin if(rst) - cnt <= #Tp {`SPI_CHAR_LEN_BITS+1{1'b0}}; + cnt <= {`SPI_CHAR_LEN_BITS+1{1'b0}}; else begin if(tip) - cnt <= #Tp pos_edge ? (cnt - {{`SPI_CHAR_LEN_BITS{1'b0}}, 1'b1}) : cnt; + cnt <= pos_edge ? (cnt - {{`SPI_CHAR_LEN_BITS{1'b0}}, 1'b1}) : cnt; else - cnt <= #Tp !(|len) ? {1'b1, {`SPI_CHAR_LEN_BITS{1'b0}}} : {1'b0, len}; + cnt <= !(|len) ? {1'b1, {`SPI_CHAR_LEN_BITS{1'b0}}} : {1'b0, len}; end end // Transfer in progress - always @(posedge clk or posedge rst) + always @(posedge clk) begin if(rst) - tip <= #Tp 1'b0; + tip <= 1'b0; else if(go && ~tip) - tip <= #Tp 1'b1; + tip <= 1'b1; else if(tip && last && pos_edge) - tip <= #Tp 1'b0; + tip <= 1'b0; end // Sending bits to the line - always @(posedge clk or posedge rst) + always @(posedge clk) begin if (rst) - s_out <= #Tp 1'b0; + s_out <= 1'b0; else - s_out <= #Tp (tx_clk || !tip) ? data[tx_bit_pos[`SPI_CHAR_LEN_BITS-1:0]] : s_out; + s_out <= (tx_clk || !tip) ? data[tx_bit_pos[`SPI_CHAR_LEN_BITS-1:0]] : s_out; end // Receiving bits from the line - always @(posedge clk or posedge rst) + always @(posedge clk) begin if (rst) - data <= #Tp {`SPI_MAX_CHAR{1'b0}}; + data <= {`SPI_MAX_CHAR{1'b0}}; `ifdef SPI_MAX_CHAR_128 else if (latch[0] && !tip) begin if (byte_sel[3]) - data[31:24] <= #Tp p_in[31:24]; + data[31:24] <= p_in[31:24]; if (byte_sel[2]) - data[23:16] <= #Tp p_in[23:16]; + data[23:16] <= p_in[23:16]; if (byte_sel[1]) - data[15:8] <= #Tp p_in[15:8]; + data[15:8] <= p_in[15:8]; if (byte_sel[0]) - data[7:0] <= #Tp p_in[7:0]; + data[7:0] <= p_in[7:0]; end else if (latch[1] && !tip) begin if (byte_sel[3]) - data[63:56] <= #Tp p_in[31:24]; + data[63:56] <= p_in[31:24]; if (byte_sel[2]) - data[55:48] <= #Tp p_in[23:16]; + data[55:48] <= p_in[23:16]; if (byte_sel[1]) - data[47:40] <= #Tp p_in[15:8]; + data[47:40] <= p_in[15:8]; if (byte_sel[0]) - data[39:32] <= #Tp p_in[7:0]; + data[39:32] <= p_in[7:0]; end else if (latch[2] && !tip) begin if (byte_sel[3]) - data[95:88] <= #Tp p_in[31:24]; + data[95:88] <= p_in[31:24]; if (byte_sel[2]) - data[87:80] <= #Tp p_in[23:16]; + data[87:80] <= p_in[23:16]; if (byte_sel[1]) - data[79:72] <= #Tp p_in[15:8]; + data[79:72] <= p_in[15:8]; if (byte_sel[0]) - data[71:64] <= #Tp p_in[7:0]; + data[71:64] <= p_in[7:0]; end else if (latch[3] && !tip) begin if (byte_sel[3]) - data[127:120] <= #Tp p_in[31:24]; + data[127:120] <= p_in[31:24]; if (byte_sel[2]) - data[119:112] <= #Tp p_in[23:16]; + data[119:112] <= p_in[23:16]; if (byte_sel[1]) - data[111:104] <= #Tp p_in[15:8]; + data[111:104] <= p_in[15:8]; if (byte_sel[0]) - data[103:96] <= #Tp p_in[7:0]; + data[103:96] <= p_in[7:0]; end `else `ifdef SPI_MAX_CHAR_64 else if (latch[0] && !tip) begin if (byte_sel[3]) - data[31:24] <= #Tp p_in[31:24]; + data[31:24] <= p_in[31:24]; if (byte_sel[2]) - data[23:16] <= #Tp p_in[23:16]; + data[23:16] <= p_in[23:16]; if (byte_sel[1]) - data[15:8] <= #Tp p_in[15:8]; + data[15:8] <= p_in[15:8]; if (byte_sel[0]) - data[7:0] <= #Tp p_in[7:0]; + data[7:0] <= p_in[7:0]; end else if (latch[1] && !tip) begin if (byte_sel[3]) - data[63:56] <= #Tp p_in[31:24]; + data[63:56] <= p_in[31:24]; if (byte_sel[2]) - data[55:48] <= #Tp p_in[23:16]; + data[55:48] <= p_in[23:16]; if (byte_sel[1]) - data[47:40] <= #Tp p_in[15:8]; + data[47:40] <= p_in[15:8]; if (byte_sel[0]) - data[39:32] <= #Tp p_in[7:0]; + data[39:32] <= p_in[7:0]; end `else else if (latch[0] && !tip) begin `ifdef SPI_MAX_CHAR_8 if (byte_sel[0]) - data[`SPI_MAX_CHAR-1:0] <= #Tp p_in[`SPI_MAX_CHAR-1:0]; + data[`SPI_MAX_CHAR-1:0] <= p_in[`SPI_MAX_CHAR-1:0]; `endif `ifdef SPI_MAX_CHAR_16 if (byte_sel[0]) - data[7:0] <= #Tp p_in[7:0]; + data[7:0] <= p_in[7:0]; if (byte_sel[1]) - data[`SPI_MAX_CHAR-1:8] <= #Tp p_in[`SPI_MAX_CHAR-1:8]; + data[`SPI_MAX_CHAR-1:8] <= p_in[`SPI_MAX_CHAR-1:8]; `endif `ifdef SPI_MAX_CHAR_24 if (byte_sel[0]) - data[7:0] <= #Tp p_in[7:0]; + data[7:0] <= p_in[7:0]; if (byte_sel[1]) - data[15:8] <= #Tp p_in[15:8]; + data[15:8] <= p_in[15:8]; if (byte_sel[2]) - data[`SPI_MAX_CHAR-1:16] <= #Tp p_in[`SPI_MAX_CHAR-1:16]; + data[`SPI_MAX_CHAR-1:16] <= p_in[`SPI_MAX_CHAR-1:16]; `endif `ifdef SPI_MAX_CHAR_32 if (byte_sel[0]) - data[7:0] <= #Tp p_in[7:0]; + data[7:0] <= p_in[7:0]; if (byte_sel[1]) - data[15:8] <= #Tp p_in[15:8]; + data[15:8] <= p_in[15:8]; if (byte_sel[2]) - data[23:16] <= #Tp p_in[23:16]; + data[23:16] <= p_in[23:16]; if (byte_sel[3]) - data[`SPI_MAX_CHAR-1:24] <= #Tp p_in[`SPI_MAX_CHAR-1:24]; + data[`SPI_MAX_CHAR-1:24] <= p_in[`SPI_MAX_CHAR-1:24]; `endif end `endif `endif else - data[rx_bit_pos[`SPI_CHAR_LEN_BITS-1:0]] <= #Tp rx_clk ? s_in : data[rx_bit_pos[`SPI_CHAR_LEN_BITS-1:0]]; + data[rx_bit_pos[`SPI_CHAR_LEN_BITS-1:0]] <= rx_clk ? s_in : data[rx_bit_pos[`SPI_CHAR_LEN_BITS-1:0]]; end endmodule diff --git a/fpga/usrp2/opencores/spi/rtl/verilog/spi_top.v b/fpga/usrp2/opencores/spi/rtl/verilog/spi_top.v index 09b2e50e1..8289449a9 100644 --- a/fpga/usrp2/opencores/spi/rtl/verilog/spi_top.v +++ b/fpga/usrp2/opencores/spi/rtl/verilog/spi_top.v @@ -1,3 +1,6 @@ + +// Modified 2010 by Matt Ettus to remove old verilog style + ////////////////////////////////////////////////////////////////////// //// //// //// spi_top.v //// @@ -40,7 +43,6 @@ `include "spi_defines.v" -`include "timescale.v" module spi_top ( @@ -52,8 +54,6 @@ module spi_top ss_pad_o, sclk_pad_o, mosi_pad_o, miso_pad_i ); - parameter Tp = 1; - // Wishbone signals input wb_clk_i; // master clock input input wb_rst_i; // synchronous active high reset @@ -101,7 +101,7 @@ module spi_top wire last_bit; // marks last character bit // Address decoder - assign spi_divider_sel = wb_cyc_i & wb_stb_i & (wb_adr_i[`SPI_OFS_BITS] == `SPI_DEVIDE); + assign spi_divider_sel = wb_cyc_i & wb_stb_i & (wb_adr_i[`SPI_OFS_BITS] == `SPI_DIVIDE); assign spi_ctrl_sel = wb_cyc_i & wb_stb_i & (wb_adr_i[`SPI_OFS_BITS] == `SPI_CTRL); assign spi_tx_sel[0] = wb_cyc_i & wb_stb_i & (wb_adr_i[`SPI_OFS_BITS] == `SPI_TX_0); assign spi_tx_sel[1] = wb_cyc_i & wb_stb_i & (wb_adr_i[`SPI_OFS_BITS] == `SPI_TX_1); @@ -132,96 +132,96 @@ module spi_top `endif `endif `SPI_CTRL: wb_dat = {{32-`SPI_CTRL_BIT_NB{1'b0}}, ctrl}; - `SPI_DEVIDE: wb_dat = {{32-`SPI_DIVIDER_LEN{1'b0}}, divider}; + `SPI_DIVIDE: wb_dat = {{32-`SPI_DIVIDER_LEN{1'b0}}, divider}; `SPI_SS: wb_dat = {{32-`SPI_SS_NB{1'b0}}, ss}; default: wb_dat = 32'bx; endcase end // Wb data out - always @(posedge wb_clk_i or posedge wb_rst_i) + always @(posedge wb_clk_i) begin if (wb_rst_i) - wb_dat_o <= #Tp 32'b0; + wb_dat_o <= 32'b0; else - wb_dat_o <= #Tp wb_dat; + wb_dat_o <= wb_dat; end // Wb acknowledge - always @(posedge wb_clk_i or posedge wb_rst_i) + always @(posedge wb_clk_i) begin if (wb_rst_i) - wb_ack_o <= #Tp 1'b0; + wb_ack_o <= 1'b0; else - wb_ack_o <= #Tp wb_cyc_i & wb_stb_i & ~wb_ack_o; + wb_ack_o <= wb_cyc_i & wb_stb_i & ~wb_ack_o; end // Wb error assign wb_err_o = 1'b0; // Interrupt - always @(posedge wb_clk_i or posedge wb_rst_i) + always @(posedge wb_clk_i) begin if (wb_rst_i) - wb_int_o <= #Tp 1'b0; + wb_int_o <= 1'b0; else if (ie && tip && last_bit && pos_edge) - wb_int_o <= #Tp 1'b1; + wb_int_o <= 1'b1; else if (wb_ack_o) - wb_int_o <= #Tp 1'b0; + wb_int_o <= 1'b0; end // Divider register - always @(posedge wb_clk_i or posedge wb_rst_i) + always @(posedge wb_clk_i) begin if (wb_rst_i) - divider <= #Tp {`SPI_DIVIDER_LEN{1'b0}}; + divider <= {`SPI_DIVIDER_LEN{1'b0}}; else if (spi_divider_sel && wb_we_i && !tip) begin `ifdef SPI_DIVIDER_LEN_8 if (wb_sel_i[0]) - divider <= #Tp wb_dat_i[`SPI_DIVIDER_LEN-1:0]; + divider <= wb_dat_i[`SPI_DIVIDER_LEN-1:0]; `endif `ifdef SPI_DIVIDER_LEN_16 if (wb_sel_i[0]) - divider[7:0] <= #Tp wb_dat_i[7:0]; + divider[7:0] <= wb_dat_i[7:0]; if (wb_sel_i[1]) - divider[`SPI_DIVIDER_LEN-1:8] <= #Tp wb_dat_i[`SPI_DIVIDER_LEN-1:8]; + divider[`SPI_DIVIDER_LEN-1:8] <= wb_dat_i[`SPI_DIVIDER_LEN-1:8]; `endif `ifdef SPI_DIVIDER_LEN_24 if (wb_sel_i[0]) - divider[7:0] <= #Tp wb_dat_i[7:0]; + divider[7:0] <= wb_dat_i[7:0]; if (wb_sel_i[1]) - divider[15:8] <= #Tp wb_dat_i[15:8]; + divider[15:8] <= wb_dat_i[15:8]; if (wb_sel_i[2]) - divider[`SPI_DIVIDER_LEN-1:16] <= #Tp wb_dat_i[`SPI_DIVIDER_LEN-1:16]; + divider[`SPI_DIVIDER_LEN-1:16] <= wb_dat_i[`SPI_DIVIDER_LEN-1:16]; `endif `ifdef SPI_DIVIDER_LEN_32 if (wb_sel_i[0]) - divider[7:0] <= #Tp wb_dat_i[7:0]; + divider[7:0] <= wb_dat_i[7:0]; if (wb_sel_i[1]) - divider[15:8] <= #Tp wb_dat_i[15:8]; + divider[15:8] <= wb_dat_i[15:8]; if (wb_sel_i[2]) - divider[23:16] <= #Tp wb_dat_i[23:16]; + divider[23:16] <= wb_dat_i[23:16]; if (wb_sel_i[3]) - divider[`SPI_DIVIDER_LEN-1:24] <= #Tp wb_dat_i[`SPI_DIVIDER_LEN-1:24]; + divider[`SPI_DIVIDER_LEN-1:24] <= wb_dat_i[`SPI_DIVIDER_LEN-1:24]; `endif end end // Ctrl register - always @(posedge wb_clk_i or posedge wb_rst_i) + always @(posedge wb_clk_i) begin if (wb_rst_i) - ctrl <= #Tp {`SPI_CTRL_BIT_NB{1'b0}}; + ctrl <= {`SPI_CTRL_BIT_NB{1'b0}}; else if(spi_ctrl_sel && wb_we_i && !tip) begin if (wb_sel_i[0]) - ctrl[7:0] <= #Tp wb_dat_i[7:0] | {7'b0, ctrl[0]}; + ctrl[7:0] <= wb_dat_i[7:0] | {7'b0, ctrl[0]}; if (wb_sel_i[1]) - ctrl[`SPI_CTRL_BIT_NB-1:8] <= #Tp wb_dat_i[`SPI_CTRL_BIT_NB-1:8]; + ctrl[`SPI_CTRL_BIT_NB-1:8] <= wb_dat_i[`SPI_CTRL_BIT_NB-1:8]; end else if(tip && last_bit && pos_edge) - ctrl[`SPI_CTRL_GO] <= #Tp 1'b0; + ctrl[`SPI_CTRL_GO] <= 1'b0; end assign rx_negedge = ctrl[`SPI_CTRL_RX_NEGEDGE]; @@ -233,39 +233,39 @@ module spi_top assign ass = ctrl[`SPI_CTRL_ASS]; // Slave select register - always @(posedge wb_clk_i or posedge wb_rst_i) + always @(posedge wb_clk_i) begin if (wb_rst_i) - ss <= #Tp {`SPI_SS_NB{1'b0}}; + ss <= {`SPI_SS_NB{1'b0}}; else if(spi_ss_sel && wb_we_i && !tip) begin `ifdef SPI_SS_NB_8 if (wb_sel_i[0]) - ss <= #Tp wb_dat_i[`SPI_SS_NB-1:0]; + ss <= wb_dat_i[`SPI_SS_NB-1:0]; `endif `ifdef SPI_SS_NB_16 if (wb_sel_i[0]) - ss[7:0] <= #Tp wb_dat_i[7:0]; + ss[7:0] <= wb_dat_i[7:0]; if (wb_sel_i[1]) - ss[`SPI_SS_NB-1:8] <= #Tp wb_dat_i[`SPI_SS_NB-1:8]; + ss[`SPI_SS_NB-1:8] <= wb_dat_i[`SPI_SS_NB-1:8]; `endif `ifdef SPI_SS_NB_24 if (wb_sel_i[0]) - ss[7:0] <= #Tp wb_dat_i[7:0]; + ss[7:0] <= wb_dat_i[7:0]; if (wb_sel_i[1]) - ss[15:8] <= #Tp wb_dat_i[15:8]; + ss[15:8] <= wb_dat_i[15:8]; if (wb_sel_i[2]) - ss[`SPI_SS_NB-1:16] <= #Tp wb_dat_i[`SPI_SS_NB-1:16]; + ss[`SPI_SS_NB-1:16] <= wb_dat_i[`SPI_SS_NB-1:16]; `endif `ifdef SPI_SS_NB_32 if (wb_sel_i[0]) - ss[7:0] <= #Tp wb_dat_i[7:0]; + ss[7:0] <= wb_dat_i[7:0]; if (wb_sel_i[1]) - ss[15:8] <= #Tp wb_dat_i[15:8]; + ss[15:8] <= wb_dat_i[15:8]; if (wb_sel_i[2]) - ss[23:16] <= #Tp wb_dat_i[23:16]; + ss[23:16] <= wb_dat_i[23:16]; if (wb_sel_i[3]) - ss[`SPI_SS_NB-1:24] <= #Tp wb_dat_i[`SPI_SS_NB-1:24]; + ss[`SPI_SS_NB-1:24] <= wb_dat_i[`SPI_SS_NB-1:24]; `endif end end diff --git a/fpga/usrp2/opencores/spi/rtl/verilog/spi_top16.v b/fpga/usrp2/opencores/spi/rtl/verilog/spi_top16.v new file mode 100644 index 000000000..ee808a8ab --- /dev/null +++ b/fpga/usrp2/opencores/spi/rtl/verilog/spi_top16.v @@ -0,0 +1,182 @@ + +// Modified 2010 by Matt Ettus to remove old verilog style and +// allow 16-bit operation + +////////////////////////////////////////////////////////////////////// +//// //// +//// spi_top.v //// +//// //// +//// This file is part of the SPI IP core project //// +//// http://www.opencores.org/projects/spi/ //// +//// //// +//// Author(s): //// +//// - Simon Srot (simons@opencores.org) //// +//// //// +//// All additional information is avaliable in the Readme.txt //// +//// file. //// +//// //// +////////////////////////////////////////////////////////////////////// +//// //// +//// Copyright (C) 2002 Authors //// +//// //// +//// This source file may be used and distributed without //// +//// restriction provided that this copyright statement is not //// +//// removed from the file and that any derivative work contains //// +//// the original copyright notice and the associated disclaimer. //// +//// //// +//// This source file is free software; you can redistribute it //// +//// and/or modify it under the terms of the GNU Lesser General //// +//// Public License as published by the Free Software Foundation; //// +//// either version 2.1 of the License, or (at your option) any //// +//// later version. //// +//// //// +//// This source is distributed in the hope that it will be //// +//// useful, but WITHOUT ANY WARRANTY; without even the implied //// +//// warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR //// +//// PURPOSE. See the GNU Lesser General Public License for more //// +//// details. //// +//// //// +//// You should have received a copy of the GNU Lesser General //// +//// Public License along with this source; if not, download it //// +//// from http://www.opencores.org/lgpl.shtml //// +//// //// +////////////////////////////////////////////////////////////////////// + + +`include "spi_defines.v" + +module spi_top16 + (input wb_clk_i, input wb_rst_i, + input [4:0] wb_adr_i, + input [15:0] wb_dat_i, + output reg [15:0] wb_dat_o, + input [1:0] wb_sel_i, + input wb_we_i, input wb_stb_i, input wb_cyc_i, + output reg wb_ack_o, output wb_err_o, output reg wb_int_o, + + // SPI signals + output [15:0] ss_pad_o, output sclk_pad_o, output mosi_pad_o, input miso_pad_i); + + // Internal signals + reg [15:0] divider; // Divider register + reg [`SPI_CTRL_BIT_NB-1:0] ctrl; // Control and status register + reg [15:0] ss; // Slave select register + reg [31:0] wb_dat; // wb data out + wire [31:0] rx; // Rx register + wire rx_negedge; // miso is sampled on negative edge + wire tx_negedge; // mosi is driven on negative edge + wire [`SPI_CHAR_LEN_BITS-1:0] char_len; // char len + wire go; // go + wire lsb; // lsb first on line + wire ie; // interrupt enable + wire ass; // automatic slave select + wire spi_divider_sel; // divider register select + wire spi_ctrl_sel; // ctrl register select + wire [3:0] spi_tx_sel; // tx_l register select + wire spi_ss_sel; // ss register select + wire tip; // transfer in progress + wire pos_edge; // recognize posedge of sclk + wire neg_edge; // recognize negedge of sclk + wire last_bit; // marks last character bit + + // Address decoder + assign spi_divider_sel = wb_cyc_i & wb_stb_i & (wb_adr_i[4:2] == `SPI_DIVIDE); + assign spi_ctrl_sel = wb_cyc_i & wb_stb_i & (wb_adr_i[4:2] == `SPI_CTRL); + assign spi_tx_sel[0] = wb_cyc_i & wb_stb_i & (wb_adr_i[4:2] == `SPI_TX_0); + assign spi_tx_sel[1] = wb_cyc_i & wb_stb_i & (wb_adr_i[4:2] == `SPI_TX_1); + assign spi_tx_sel[2] = wb_cyc_i & wb_stb_i & (wb_adr_i[4:2] == `SPI_TX_2); + assign spi_tx_sel[3] = wb_cyc_i & wb_stb_i & (wb_adr_i[4:2] == `SPI_TX_3); + assign spi_ss_sel = wb_cyc_i & wb_stb_i & (wb_adr_i[4:2] == `SPI_SS); + + always @(wb_adr_i or rx or ctrl or divider or ss) + case (wb_adr_i[4:2]) + `SPI_RX_0: wb_dat = rx[31:0]; + `SPI_CTRL: wb_dat = {{32-`SPI_CTRL_BIT_NB{1'b0}}, ctrl}; + `SPI_DIVIDE: wb_dat = {16'b0, divider}; + `SPI_SS: wb_dat = {16'b0, ss}; + default : wb_dat = 32'd0; + endcase // case (wb_adr_i[4:2]) + + always @(posedge wb_clk_i) + if (wb_rst_i) + wb_dat_o <= 32'b0; + else + wb_dat_o <= wb_adr_i[1] ? wb_dat[31:16] : wb_dat[15:0]; + + always @(posedge wb_clk_i) + if (wb_rst_i) + wb_ack_o <= 1'b0; + else + wb_ack_o <= wb_cyc_i & wb_stb_i & ~wb_ack_o; + + assign wb_err_o = 1'b0; + + // Interrupt + always @(posedge wb_clk_i) + if (wb_rst_i) + wb_int_o <= 1'b0; + else if (ie && tip && last_bit && pos_edge) + wb_int_o <= 1'b1; + else if (wb_ack_o) + wb_int_o <= 1'b0; + + // Divider register + always @(posedge wb_clk_i) + if (wb_rst_i) + divider <= 16'b0; + else if (spi_divider_sel && wb_we_i && !tip && ~wb_adr_i[1]) + divider <= wb_dat_i; + + // Ctrl register + always @(posedge wb_clk_i) + if (wb_rst_i) + ctrl <= {`SPI_CTRL_BIT_NB{1'b0}}; + else if(spi_ctrl_sel && wb_we_i && !tip && ~wb_adr_i[1]) + begin + if (wb_sel_i[0]) + ctrl[7:0] <= wb_dat_i[7:0] | {7'b0, ctrl[0]}; + if (wb_sel_i[1]) + ctrl[`SPI_CTRL_BIT_NB-1:8] <= wb_dat_i[`SPI_CTRL_BIT_NB-1:8]; + end + else if(tip && last_bit && pos_edge) + ctrl[`SPI_CTRL_GO] <= 1'b0; + + assign rx_negedge = ctrl[`SPI_CTRL_RX_NEGEDGE]; + assign tx_negedge = ctrl[`SPI_CTRL_TX_NEGEDGE]; + assign go = ctrl[`SPI_CTRL_GO]; + assign char_len = ctrl[`SPI_CTRL_CHAR_LEN]; + assign lsb = ctrl[`SPI_CTRL_LSB]; + assign ie = ctrl[`SPI_CTRL_IE]; + assign ass = ctrl[`SPI_CTRL_ASS]; + + // Slave select register + always @(posedge wb_clk_i) + if (wb_rst_i) + ss <= 16'b0; + else if(spi_ss_sel && wb_we_i && !tip & ~wb_adr_i[1]) + begin + if (wb_sel_i[0]) + ss[7:0] <= wb_dat_i[7:0]; + if (wb_sel_i[1]) + ss[15:8] <= wb_dat_i[15:8]; + end + + assign ss_pad_o = ~((ss & {16{tip & ass}}) | (ss & {16{!ass}})); + + spi_clgen clgen (.clk_in(wb_clk_i), .rst(wb_rst_i), .go(go), .enable(tip), .last_clk(last_bit), + .divider(divider[`SPI_DIVIDER_LEN-1:0]), .clk_out(sclk_pad_o), .pos_edge(pos_edge), + .neg_edge(neg_edge)); + + wire [3:0] new_sels = { (wb_adr_i[1] & wb_sel_i[1]), (wb_adr_i[1] & wb_sel_i[0]), + (~wb_adr_i[1] & wb_sel_i[1]), (~wb_adr_i[1] & wb_sel_i[0]) }; + + + spi_shift shift (.clk(wb_clk_i), .rst(wb_rst_i), .len(char_len[`SPI_CHAR_LEN_BITS-1:0]), + .latch(spi_tx_sel[3:0] & {4{wb_we_i}}), .byte_sel(new_sels), .lsb(lsb), + .go(go), .pos_edge(pos_edge), .neg_edge(neg_edge), + .rx_negedge(rx_negedge), .tx_negedge(tx_negedge), + .tip(tip), .last(last_bit), + .p_in({wb_dat_i,wb_dat_i}), .p_out(rx), + .s_clk(sclk_pad_o), .s_in(miso_pad_i), .s_out(mosi_pad_o)); + +endmodule // spi_top16 diff --git a/fpga/usrp2/opencores/spi/rtl/verilog/timescale.v b/fpga/usrp2/opencores/spi/rtl/verilog/timescale.v deleted file mode 100644 index 60d4ecbd1..000000000 --- a/fpga/usrp2/opencores/spi/rtl/verilog/timescale.v +++ /dev/null @@ -1,2 +0,0 @@ -`timescale 1ns / 10ps - diff --git a/fpga/usrp2/top/.gitignore b/fpga/usrp2/top/.gitignore index bf1b77066..0d90f1698 100644 --- a/fpga/usrp2/top/.gitignore +++ b/fpga/usrp2/top/.gitignore @@ -1 +1,2 @@ /*.sav +build* diff --git a/fpga/usrp2/top/u1e/.gitignore b/fpga/usrp2/top/u1e/.gitignore new file mode 100644 index 000000000..8d872713e --- /dev/null +++ b/fpga/usrp2/top/u1e/.gitignore @@ -0,0 +1,6 @@ +*~ +build +*.log +*.cmd +tb_u1e +*.lxt diff --git a/fpga/usrp2/top/u1e/Makefile b/fpga/usrp2/top/u1e/Makefile new file mode 100644 index 000000000..3cb9fd8f3 --- /dev/null +++ b/fpga/usrp2/top/u1e/Makefile @@ -0,0 +1,101 @@ +# +# Copyright 2008 Ettus Research LLC +# + +################################################## +# Project Setup +################################################## +TOP_MODULE = u1e +BUILD_DIR = $(abspath build$(ISE)) + +################################################## +# Include other makefiles +################################################## + +include ../Makefile.common +include ../../fifo/Makefile.srcs +include ../../control_lib/Makefile.srcs +include ../../sdr_lib/Makefile.srcs +include ../../serdes/Makefile.srcs +include ../../simple_gemac/Makefile.srcs +include ../../timing/Makefile.srcs +include ../../opencores/Makefile.srcs +include ../../vrt/Makefile.srcs +include ../../udp/Makefile.srcs +include ../../coregen/Makefile.srcs +include ../../extram/Makefile.srcs +include ../../gpmc/Makefile.srcs + +################################################## +# Project Properties +################################################## +export PROJECT_PROPERTIES := \ +family "Spartan-3A DSP" \ +device xc3sd1800a \ +package cs484 \ +speed -4 \ +top_level_module_type "HDL" \ +synthesis_tool "XST (VHDL/Verilog)" \ +simulator "ISE Simulator (VHDL/Verilog)" \ +"Preferred Language" "Verilog" \ +"Enable Message Filtering" FALSE \ +"Display Incremental Messages" FALSE + +################################################## +# Sources +################################################## +TOP_SRCS = \ +u1e_core.v \ +u1e.v \ +u1e.ucf \ +timing.ucf + +SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \ +$(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \ +$(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \ +$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS) \ +$(GPMC_SRCS) + +################################################## +# Process Properties +################################################## +SYNTHESIZE_PROPERTIES = \ +"Number of Clock Buffers" 8 \ +"Pack I/O Registers into IOBs" Yes \ +"Optimization Effort" High \ +"Optimize Instantiated Primitives" TRUE \ +"Register Balancing" Yes \ +"Use Clock Enable" Auto \ +"Use Synchronous Reset" Auto \ +"Use Synchronous Set" Auto + +TRANSLATE_PROPERTIES = \ +"Macro Search Path" "$(shell pwd)/../../coregen/" + +MAP_PROPERTIES = \ +"Allow Logic Optimization Across Hierarchy" TRUE \ +"Map to Input Functions" 4 \ +"Optimization Strategy (Cover Mode)" Speed \ +"Pack I/O Registers/Latches into IOBs" "For Inputs and Outputs" \ +"Perform Timing-Driven Packing and Placement" TRUE \ +"Map Effort Level" High \ +"Extra Effort" Normal \ +"Combinatorial Logic Optimization" TRUE \ +"Register Duplication" TRUE + +PLACE_ROUTE_PROPERTIES = \ +"Place & Route Effort Level (Overall)" High + +STATIC_TIMING_PROPERTIES = \ +"Number of Paths in Error/Verbose Report" 10 \ +"Report Type" "Error Report" + +GEN_PROG_FILE_PROPERTIES = \ +"Configuration Rate" 6 \ +"Create Binary Configuration File" TRUE \ +"Done (Output Events)" 5 \ +"Enable Bitstream Compression" TRUE \ +"Enable Outputs (Output Events)" 6 \ +"Unused IOB Pins" "Pull Up" + +SIM_MODEL_PROPERTIES = "" diff --git a/fpga/usrp2/top/u1e/README b/fpga/usrp2/top/u1e/README new file mode 100644 index 000000000..14c7a4955 --- /dev/null +++ b/fpga/usrp2/top/u1e/README @@ -0,0 +1,4 @@ + +make clean +make sim +./tb_u1e -lxt2 diff --git a/fpga/usrp2/top/u1e/cmdfile b/fpga/usrp2/top/u1e/cmdfile new file mode 100644 index 000000000..291c723b8 --- /dev/null +++ b/fpga/usrp2/top/u1e/cmdfile @@ -0,0 +1,20 @@ + +# My stuff +-y . +-y ../../control_lib +-y ../../control_lib/newfifo +-y ../../sdr_lib +-y ../../timing +-y ../../coregen +-y ../../gpmc + +# Models +-y ../../models +-y /opt/Xilinx/10.1/ISE/verilog/src/unisims + +# Open Cores +-y ../../opencores/spi/rtl/verilog ++incdir+../../opencores/spi/rtl/verilog +-y ../../opencores/i2c/rtl/verilog ++incdir+../../opencores/i2c/rtl/verilog + diff --git a/fpga/usrp2/top/u1e/make.sim b/fpga/usrp2/top/u1e/make.sim new file mode 100644 index 000000000..1c163884c --- /dev/null +++ b/fpga/usrp2/top/u1e/make.sim @@ -0,0 +1,7 @@ +all: sim + +sim: + iverilog -Wimplicit -Wportbind -c cmdfile tb_u1e.v -o tb_u1e + +clean: + rm -f tb_u1e *.vcd *.lxt a.out diff --git a/fpga/usrp2/top/u1e/tb_u1e.v b/fpga/usrp2/top/u1e/tb_u1e.v new file mode 100644 index 000000000..5fc8134fb --- /dev/null +++ b/fpga/usrp2/top/u1e/tb_u1e.v @@ -0,0 +1,41 @@ +`timescale 1ps / 1ps +////////////////////////////////////////////////////////////////////////////////// + +module tb_u1e(); + + wire [2:0] debug_led; + wire [31:0] debug; + wire [1:0] debug_clk; + + xlnx_glbl glbl (.GSR(),.GTS()); + + initial begin + $dumpfile("tb_u1e.lxt"); + $dumpvars(0,tb_u1e); + end + + // GPMC + wire EM_CLK, EM_WAIT0, EM_NCS4, EM_NCS6, EM_NWE, EM_NOE; + wire [15:0] EM_D; + wire [10:1] EM_A; + wire [1:0] EM_NBE; + + reg clk_fpga = 0, rst_fpga = 1; + always #15625 clk_fpga = ~clk_fpga; + + initial #200000 + @(posedge clk_fpga) + rst_fpga <= 0; + + u1e_core u1e_core(.clk_fpga(clk_fpga), .rst_fpga(rst_fpga), + .debug_led(debug_led), .debug(debug), .debug_clk(debug_clk), + .EM_CLK(EM_CLK), .EM_D(EM_D), .EM_A(EM_A), .EM_NBE(EM_NBE), + .EM_WAIT0(EM_WAIT0), .EM_NCS4(EM_NCS4), .EM_NCS6(EM_NCS6), + .EM_NWE(EM_NWE), .EM_NOE(EM_NOE) ); + + gpmc_model_async gpmc_model_async + (.EM_CLK(EM_CLK), .EM_D(EM_D), .EM_A(EM_A), .EM_NBE(EM_NBE), + .EM_WAIT0(EM_WAIT0), .EM_NCS4(EM_NCS4), .EM_NCS6(EM_NCS6), + .EM_NWE(EM_NWE), .EM_NOE(EM_NOE) ); + +endmodule // tb_u1e diff --git a/fpga/usrp2/top/u1e/timing.ucf b/fpga/usrp2/top/u1e/timing.ucf new file mode 100644 index 000000000..8df28c9d3 --- /dev/null +++ b/fpga/usrp2/top/u1e/timing.ucf @@ -0,0 +1,13 @@ + +NET "CLK_FPGA_P" TNM_NET = "CLK_FPGA_P"; +TIMESPEC "TS_clk_fpga_p" = PERIOD "CLK_FPGA_P" 15625 ps HIGH 50 %; + + + + +#NET "adc_a<*>" TNM_NET = ADC_DATA_GRP; +#NET "adc_b<*>" TNM_NET = ADC_DATA_GRP; +#TIMEGRP "ADC_DATA_GRP" OFFSET = IN 1 ns VALID 5 ns BEFORE "clk_fpga_p" RISING; + +#NET "adc_a<*>" OFFSET = IN 1 ns VALID 5 ns BEFORE "clk_fpga_p" RISING; +#NET "adc_b<*>" OFFSET = IN 1 ns VALID 5 ns BEFORE "clk_fpga_p" RISING; diff --git a/fpga/usrp2/top/u1e/u1e.ucf b/fpga/usrp2/top/u1e/u1e.ucf new file mode 100644 index 000000000..0c487a601 --- /dev/null +++ b/fpga/usrp2/top/u1e/u1e.ucf @@ -0,0 +1,259 @@ + +NET "CLK_FPGA_P" LOC = "Y11" ; +NET "CLK_FPGA_N" LOC = "Y10" ; + +## GPMC +NET "EM_D<15>" LOC = "D13" ; +NET "EM_D<14>" LOC = "D15" ; +NET "EM_D<13>" LOC = "C16" ; +NET "EM_D<12>" LOC = "B20" ; +NET "EM_D<11>" LOC = "A19" ; +NET "EM_D<10>" LOC = "A17" ; +NET "EM_D<9>" LOC = "E15" ; +NET "EM_D<8>" LOC = "F15" ; +NET "EM_D<7>" LOC = "E16" ; +NET "EM_D<6>" LOC = "F16" ; +NET "EM_D<5>" LOC = "B17" ; +NET "EM_D<4>" LOC = "C17" ; +NET "EM_D<3>" LOC = "B19" ; +NET "EM_D<2>" LOC = "D19" ; +NET "EM_D<1>" LOC = "C19" ; +NET "EM_D<0>" LOC = "A20" ; + +NET "EM_A<10>" LOC = "C14" ; +NET "EM_A<9>" LOC = "C10" ; +NET "EM_A<8>" LOC = "C5" ; +NET "EM_A<7>" LOC = "A18" ; +NET "EM_A<6>" LOC = "A15" ; +NET "EM_A<5>" LOC = "A12" ; +NET "EM_A<4>" LOC = "A10" ; +NET "EM_A<3>" LOC = "E7" ; +NET "EM_A<2>" LOC = "A7" ; +NET "EM_A<1>" LOC = "C15" ; + +NET "EM_NCS6" LOC = "E17" ; +NET "EM_NCS5" LOC = "E10" ; +NET "EM_NCS4" LOC = "E6" ; +#NET "EM_NCS1" LOC = "D18" ; +#NET "EM_NCS0" LOC = "D17" ; + +NET "EM_CLK" LOC = "F11" ; +NET "EM_WAIT0" LOC = "F14" ; +NET "EM_NBE<1>" LOC = "D14" ; +NET "EM_NBE<0>" LOC = "A13" ; +NET "EM_NWE" LOC = "B13" ; +NET "EM_NOE" LOC = "A14" ; +#NET "EM_NADV_ALE" LOC = "B15" ; +#NET "EM_NWP" LOC = "F13" ; + +## Overo GPIO +NET "overo_gpio0" LOC = "F9" ; # MISC GPIO for debug +NET "overo_gpio14" LOC = "C4" ; # MISC GPIO for debug +NET "overo_gpio21" LOC = "D5" ; # MISC GPIO for debug +NET "overo_gpio22" LOC = "A3" ; # MISC GPIO for debug +NET "overo_gpio23" LOC = "B3" ; # MISC GPIO for debug +NET "overo_gpio64" LOC = "A4" ; # MISC GPIO for debug +NET "overo_gpio65" LOC = "F8" ; # MISC GPIO for debug + +NET "overo_gpio127" LOC = "C8" ; # Changed name to gpio10 +NET "overo_gpio128" LOC = "G8" ; # Changed name to gpio186 + +NET "overo_gpio144" LOC = "A5" ; # tx_have_space +NET "overo_gpio145" LOC = "C7" ; # tx_underrun +NET "overo_gpio146" LOC = "A6" ; # rx_have_data +NET "overo_gpio147" LOC = "B6" ; # rx_overrun +NET "overo_gpio163" LOC = "D7" ; # MISC GPIO for debug +NET "overo_gpio170" LOC = "E8" ; # MISC GPIO for debug +NET "overo_gpio176" LOC = "B4" ; # MISC GPIO for debug + +## Overo UART +#NET "overo_txd1" LOC = "C6" ; +#NET "overo_rxd1" LOC = "D6" ; + +## FTDI UART to USB converter +NET "FPGA_TXD" LOC = "G19" ; +NET "FPGA_RXD" LOC = "F20" ; + +#NET "SYSEN" LOC = "C11" ; + +## I2C +NET "db_scl" LOC = "F19" ; +NET "db_sda" LOC = "F18" ; + +## SPI +### DBoard SPI +NET "db_sclk_rx" LOC = "D21" ; +NET "db_miso_rx" LOC = "D22" ; +NET "db_mosi_rx" LOC = "D20" ; +NET "db_sen_rx" LOC = "E19" ; +NET "db_sclk_tx" LOC = "F21" ; +NET "db_miso_tx" LOC = "E20" ; +NET "db_mosi_tx" LOC = "G17" ; +NET "db_sen_tx" LOC = "G18" ; + +### AD9862 SPI and aux SPI Interfaces +#NET "aux_sdi_codec" LOC = "G3" ; +#NET "aux_sdo_codec" LOC = "F3" ; +#NET "aux_sclk_codec" LOC = "C1" ; +NET "sen_codec" LOC = "F5" |IOSTANDARD = LVCMOS33; +NET "mosi_codec" LOC = "F4" |IOSTANDARD = LVCMOS33; +NET "miso_codec" LOC = "H4" ; +NET "sclk_codec" LOC = "H3" |IOSTANDARD = LVCMOS33; + +### Clock Gen SPI +NET "cgen_miso" LOC = "F22" ; +NET "cgen_mosi" LOC = "E22" ; +NET "cgen_sclk" LOC = "J19" ; +NET "cgen_sen_b" LOC = "H20" ; + +## Clock gen control +NET "cgen_st_status" LOC = "P20" ; +NET "cgen_st_ld" LOC = "R17" ; +NET "cgen_st_refmon" LOC = "P17" ; +NET "cgen_sync_b" LOC = "U18" ; +NET "cgen_ref_sel" LOC = "U19" ; + +## Debug pins +NET "debug_led<3>" LOC = "Y15" ; +NET "debug_led<2>" LOC = "K16" ; +NET "debug_led<1>" LOC = "J17" ; +NET "debug_led<0>" LOC = "H22" ; +NET "debug<0>" LOC = "G22" ; +NET "debug<1>" LOC = "H17" ; +NET "debug<2>" LOC = "H18" ; +NET "debug<3>" LOC = "K20" ; +NET "debug<4>" LOC = "J20" ; +NET "debug<5>" LOC = "K19" ; +NET "debug<6>" LOC = "K18" ; +NET "debug<7>" LOC = "L22" ; +NET "debug<8>" LOC = "K22" ; +NET "debug<9>" LOC = "N22" ; +NET "debug<10>" LOC = "M22" ; +NET "debug<11>" LOC = "N20" ; +NET "debug<12>" LOC = "N19" ; +NET "debug<13>" LOC = "R22" ; +NET "debug<14>" LOC = "P22" ; +NET "debug<15>" LOC = "N17" ; +NET "debug<16>" LOC = "P16" ; +NET "debug<17>" LOC = "U22" ; +NET "debug<18>" LOC = "P19" ; +NET "debug<19>" LOC = "R18" ; +NET "debug<20>" LOC = "U20" ; +NET "debug<21>" LOC = "T20" ; +NET "debug<22>" LOC = "R19" ; +NET "debug<23>" LOC = "R20" ; +NET "debug<24>" LOC = "W22" ; +NET "debug<25>" LOC = "Y22" ; +NET "debug<26>" LOC = "T18" ; +NET "debug<27>" LOC = "T17" ; +NET "debug<28>" LOC = "W19" ; +NET "debug<29>" LOC = "V20" ; +NET "debug<30>" LOC = "Y21" ; +NET "debug<31>" LOC = "AA22" ; +NET "debug_clk<0>" LOC = "N18" ; +NET "debug_clk<1>" LOC = "M17" ; + +NET "debug_pb" LOC = "C22" ; + +#NET "reset_codec" LOC = "C2" ; + +NET "RXSYNC" LOC = "F2" ; +NET "DB<11>" LOC = "G6" ; +NET "DB<10>" LOC = "G5" ; +NET "DB<9>" LOC = "E4" ; +NET "DB<8>" LOC = "E3" ; +NET "DB<7>" LOC = "H6" ; +NET "DB<6>" LOC = "H5" ; +NET "DB<5>" LOC = "H1" ; +NET "DB<4>" LOC = "G1" ; +NET "DB<3>" LOC = "K5" ; +NET "DB<2>" LOC = "K4" ; +NET "DB<1>" LOC = "H2" ; +NET "DB<0>" LOC = "L5" ; + +NET "DA<11>" LOC = "K6" ; +NET "DA<10>" LOC = "K3" ; +NET "DA<9>" LOC = "K2" ; +NET "DA<8>" LOC = "N1" ; +NET "DA<7>" LOC = "N5" ; +NET "DA<6>" LOC = "N6" ; +NET "DA<5>" LOC = "P2" ; +NET "DA<4>" LOC = "P1" ; +NET "DA<3>" LOC = "R6" ; +NET "DA<2>" LOC = "P6" ; +NET "DA<1>" LOC = "R1" ; +NET "DA<0>" LOC = "R2" ; + +NET "TX<13>" LOC = "T6" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TX<12>" LOC = "U1" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TX<11>" LOC = "T1" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TX<10>" LOC = "R5" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TX<9>" LOC = "V1" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TX<8>" LOC = "U2" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TX<7>" LOC = "T4" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TX<6>" LOC = "R3" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TX<5>" LOC = "W1" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TX<4>" LOC = "Y1" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TX<3>" LOC = "V3" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TX<2>" LOC = "V4" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TX<1>" LOC = "W2" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TX<0>" LOC = "W3" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TXSYNC" LOC = "U5" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; +NET "TXBLANK" LOC = "U4" |IOSTANDARD = LVCMOS33 |DRIVE = 12 |SLEW = FAST ; + +NET "PPS_IN" LOC = "M5" ; + +NET "io_tx<0>" LOC = "AB20" ; +NET "io_tx<1>" LOC = "Y17" ; +NET "io_tx<2>" LOC = "Y16" ; +NET "io_tx<3>" LOC = "U16" ; +NET "io_tx<4>" LOC = "V16" ; +NET "io_tx<5>" LOC = "AB19" ; +NET "io_tx<6>" LOC = "AA19" ; +NET "io_tx<7>" LOC = "U14" ; +NET "io_tx<8>" LOC = "U15" ; +NET "io_tx<9>" LOC = "AB17" ; +NET "io_tx<10>" LOC = "AB18" ; +NET "io_tx<11>" LOC = "Y13" ; +NET "io_tx<12>" LOC = "W14" ; +NET "io_tx<13>" LOC = "U13" ; +NET "io_tx<14>" LOC = "AA15" ; +NET "io_tx<15>" LOC = "AB14" ; + +NET "io_rx<0>" LOC = "Y8" ; +NET "io_rx<1>" LOC = "Y9" ; +NET "io_rx<2>" LOC = "V7" ; +NET "io_rx<3>" LOC = "U8" ; +NET "io_rx<4>" LOC = "V10" ; +NET "io_rx<5>" LOC = "U9" ; +NET "io_rx<6>" LOC = "AB7" ; +NET "io_rx<7>" LOC = "AA8" ; +NET "io_rx<8>" LOC = "W8" ; +NET "io_rx<9>" LOC = "V8" ; +NET "io_rx<10>" LOC = "AB5" ; +NET "io_rx<11>" LOC = "AB6" ; +NET "io_rx<12>" LOC = "AB4" ; +NET "io_rx<13>" LOC = "AA4" ; +NET "io_rx<14>" LOC = "W5" ; +NET "io_rx<15>" LOC = "Y4" ; + +#NET "CLKOUT2_CODEC" LOC = "U12" ; +#NET "CLKOUT1_CODEC" LOC = "V12" ; + +## FPGA Config Pins +#NET "fpga_cfg_prog_b" LOC = "A2" ; +#NET "fpga_cfg_done" LOC = "AB21" ; +#NET "fpga_cfg_din" LOC = "W17" ; +#NET "fpga_cfg_cclk" LOC = "V17" ; +#NET "fpga_cfg_init_b" LOC = "W15" ; + +## Unused +#NET "unnamed_net53" LOC = "B1" ; # TMS +#NET "unnamed_net52" LOC = "B22" ; # TDO +#NET "unnamed_net51" LOC = "D2" ; # TDI +#NET "unnamed_net50" LOC = "A21" ; # TCK +#NET "unnamed_net59" LOC = "F7" ; # PUDC_B +#NET "unnamed_net58" LOC = "V6" ; # M2 +#NET "unnamed_net57" LOC = "AA3" ; # M1 +#NET "unnamed_net56" LOC = "AB3" ; # M0 +#NET "GND" LOC = "V19" ; # Suspend, unused diff --git a/fpga/usrp2/top/u1e/u1e.v b/fpga/usrp2/top/u1e/u1e.v new file mode 100644 index 000000000..445b14a03 --- /dev/null +++ b/fpga/usrp2/top/u1e/u1e.v @@ -0,0 +1,141 @@ +`timescale 1ns / 1ps +////////////////////////////////////////////////////////////////////////////////// + +module u1e + (input CLK_FPGA_P, input CLK_FPGA_N, // Diff + output [3:0] debug_led, output [31:0] debug, output [1:0] debug_clk, + input debug_pb, output FPGA_TXD, input FPGA_RXD, + + // GPMC + input EM_CLK, inout [15:0] EM_D, input [10:1] EM_A, input [1:0] EM_NBE, + input EM_WAIT0, input EM_NCS4, input EM_NCS5, input EM_NCS6, + input EM_NWE, input EM_NOE, + + inout db_sda, inout db_scl, // I2C + + output db_sclk_tx, output db_sen_tx, output db_mosi_tx, input db_miso_tx, // DB TX SPI + output db_sclk_rx, output db_sen_rx, output db_mosi_rx, input db_miso_rx, // DB TX SPI + output sclk_codec, output sen_codec, output mosi_codec, input miso_codec, // AD9862 main SPI + output cgen_sclk, output cgen_sen_b, output cgen_mosi, input cgen_miso, // Clock gen SPI + + input cgen_st_status, input cgen_st_ld, input cgen_st_refmon, output cgen_sync_b, output cgen_ref_sel, + + output overo_gpio144, output overo_gpio145, output overo_gpio146, output overo_gpio147, // Fifo controls + input overo_gpio0, input overo_gpio14, input overo_gpio21, input overo_gpio22, // Misc GPIO + input overo_gpio23, input overo_gpio64, input overo_gpio65, input overo_gpio127, // Misc GPIO + input overo_gpio128, input overo_gpio163, input overo_gpio170, input overo_gpio176, // Misc GPIO + + inout [15:0] io_tx, inout [15:0] io_rx, + + output [13:0] TX, output TXSYNC, output TXBLANK, + input [11:0] DA, input [11:0] DB, input RXSYNC, + + input PPS_IN + ); + + // ///////////////////////////////////////////////////////////////////////// + // Clocking + wire clk_fpga, clk_fpga_in; + + IBUFGDS #(.IOSTANDARD("LVDS_33"), .DIFF_TERM("TRUE")) + clk_fpga_pin (.O(clk_fpga_in),.I(CLK_FPGA_P),.IB(CLK_FPGA_N)); + + wire clk_2x, dcm_rst, dcm_locked, clk_fb; + DCM #(.CLK_FEEDBACK ( "1X" ), + .CLKDV_DIVIDE ( 2 ), + .CLKFX_DIVIDE ( 2 ), + .CLKFX_MULTIPLY ( 2 ), + .CLKIN_DIVIDE_BY_2 ( "FALSE" ), + .CLKIN_PERIOD ( 15.625 ), + .CLKOUT_PHASE_SHIFT ( "NONE" ), + .DESKEW_ADJUST ( "SYSTEM_SYNCHRONOUS" ), + .DFS_FREQUENCY_MODE ( "LOW" ), + .DLL_FREQUENCY_MODE ( "LOW" ), + .DUTY_CYCLE_CORRECTION ( "TRUE" ), + .FACTORY_JF ( 16'h8080 ), + .PHASE_SHIFT ( 0 ), + .STARTUP_WAIT ( "FALSE" )) + clk_doubler (.CLKFB(clk_fb), .CLKIN(clk_fpga_in), .RST(dcm_rst), + .DSSEN(0), .PSCLK(0), .PSEN(0), .PSINCDEC(0), .PSDONE(), + .CLKDV(), .CLKFX(), .CLKFX180(), + .CLK2X(), .CLK2X180(), + .CLK0(clk_fb), .CLK90(clk_fpga), .CLK180(), .CLK270(), + .LOCKED(dcm_locked), .STATUS()); + + // ///////////////////////////////////////////////////////////////////////// + // SPI + wire mosi, sclk, miso; + assign { db_sclk_tx, db_mosi_tx } = ~db_sen_tx ? {sclk,mosi} : 2'b0; + assign { db_sclk_rx, db_mosi_rx } = ~db_sen_rx ? {sclk,mosi} : 2'b0; + assign { sclk_codec, mosi_codec } = ~sen_codec ? {sclk,mosi} : 2'b0; + assign { cgen_sclk, cgen_mosi } = ~cgen_sen_b ? {sclk,mosi} : 2'b0; + assign miso = (~db_sen_tx & db_miso_tx) | (~db_sen_rx & db_miso_rx) | + (~sen_codec & miso_codec) | (~cgen_sen_b & cgen_miso); + + // ///////////////////////////////////////////////////////////////////////// + // TX DAC -- handle the interleaved data bus to DAC, with clock doubling DLL + + assign TXBLANK = 0; + wire [13:0] tx_i, tx_q; + + reg[13:0] delay_q; + always @(posedge clk_fpga) + delay_q <= tx_q; + + genvar i; + generate + for(i=0;i<14;i=i+1) + begin : gen_dacout + ODDR2 #(.DDR_ALIGNMENT("NONE"), // Sets output alignment to "NONE", "C0" or "C1" + .INIT(1'b0), // Sets initial state of the Q output to 1'b0 or 1'b1 + .SRTYPE("SYNC")) // Specifies "SYNC" or "ASYNC" set/reset + ODDR2_inst (.Q(TX[i]), // 1-bit DDR output data + .C0(clk_fpga), // 1-bit clock input + .C1(~clk_fpga), // 1-bit clock input + .CE(1'b1), // 1-bit clock enable input + .D0(tx_i[i]), // 1-bit data input (associated with C0) + .D1(delay_q[i]), // 1-bit data input (associated with C1) + .R(1'b0), // 1-bit reset input + .S(1'b0)); // 1-bit set input + end // block: gen_dacout + endgenerate + ODDR2 #(.DDR_ALIGNMENT("NONE"), // Sets output alignment to "NONE", "C0" or "C1" + .INIT(1'b0), // Sets initial state of the Q output to 1'b0 or 1'b1 + .SRTYPE("SYNC")) // Specifies "SYNC" or "ASYNC" set/reset + ODDR2_txsnc (.Q(TXSYNC), // 1-bit DDR output data + .C0(clk_fpga), // 1-bit clock input + .C1(~clk_fpga), // 1-bit clock input + .CE(1'b1), // 1-bit clock enable input + .D0(1'b0), // 1-bit data input (associated with C0) + .D1(1'b1), // 1-bit data input (associated with C1) + .R(1'b0), // 1-bit reset input + .S(1'b0)); // 1-bit set input + + // ///////////////////////////////////////////////////////////////////////// + // Main U1E Core + u1e_core u1e_core(.clk_fpga(clk_fpga), .rst_fpga(~debug_pb), + .debug_led(debug_led), .debug(debug), .debug_clk(debug_clk), + .debug_txd(FPGA_TXD), .debug_rxd(FPGA_RXD), + .EM_CLK(EM_CLK), .EM_D(EM_D), .EM_A(EM_A), .EM_NBE(EM_NBE), + .EM_WAIT0(EM_WAIT0), .EM_NCS4(EM_NCS4), .EM_NCS5(EM_NCS5), + .EM_NCS6(EM_NCS6), .EM_NWE(EM_NWE), .EM_NOE(EM_NOE), + .db_sda(db_sda), .db_scl(db_scl), + .sclk(sclk), .sen({cgen_sen_b,sen_codec,db_sen_tx,db_sen_rx}), .mosi(mosi), .miso(miso), + .cgen_st_status(cgen_st_status), .cgen_st_ld(cgen_st_ld),.cgen_st_refmon(cgen_st_refmon), + .cgen_sync_b(cgen_sync_b), .cgen_ref_sel(cgen_ref_sel), + .tx_have_space(overo_gpio144), .tx_underrun(overo_gpio145), + .rx_have_data(overo_gpio146), .rx_overrun(overo_gpio147), + .io_tx(io_tx), .io_rx(io_rx), + .tx_i(tx_i), .tx_q(tx_q), + .rx_i(DA), .rx_q(DB), + .misc_gpio( {{overo_gpio128,overo_gpio163,overo_gpio170,overo_gpio176}, + {overo_gpio0,overo_gpio14,overo_gpio21,overo_gpio22}, + {overo_gpio23,overo_gpio64,overo_gpio65,overo_gpio127}}), + .pps_in(PPS_IN) ); + + // ///////////////////////////////////////////////////////////////////////// + // Local Debug + // assign debug_clk = {clk_fpga, clk_2x }; + // assign debug = { TXSYNC, TXBLANK, TX }; + +endmodule // u1e diff --git a/fpga/usrp2/top/u1e/u1e_core.v b/fpga/usrp2/top/u1e/u1e_core.v new file mode 100644 index 000000000..619e44b8a --- /dev/null +++ b/fpga/usrp2/top/u1e/u1e_core.v @@ -0,0 +1,459 @@ + + +//`define LOOPBACK 1 +//`define TIMED 1 +`define DSP 1 + +module u1e_core + (input clk_fpga, input rst_fpga, + output [3:0] debug_led, output [31:0] debug, output [1:0] debug_clk, + output debug_txd, input debug_rxd, + + // GPMC + input EM_CLK, inout [15:0] EM_D, input [10:1] EM_A, input [1:0] EM_NBE, + input EM_WAIT0, input EM_NCS4, input EM_NCS5, input EM_NCS6, + input EM_NWE, input EM_NOE, + + inout db_sda, inout db_scl, + output sclk, output [7:0] sen, output mosi, input miso, + + input cgen_st_status, input cgen_st_ld, input cgen_st_refmon, output cgen_sync_b, output cgen_ref_sel, + output tx_have_space, output tx_underrun, output rx_have_data, output rx_overrun, + inout [15:0] io_tx, inout [15:0] io_rx, + output [13:0] tx_i, output [13:0] tx_q, + input [11:0] rx_i, input [11:0] rx_q, + + input [11:0] misc_gpio, input pps_in + ); + + localparam TXFIFOSIZE = 13; + localparam RXFIFOSIZE = 13; + + localparam SR_RX_DSP = 0; // 5 regs + localparam SR_CLEAR_FIFO = 6; // 1 reg + localparam SR_RX_CTRL = 8; // 9 regs + localparam SR_TX_DSP = 17; // 5 regs + localparam SR_TX_CTRL = 24; // 2 regs + localparam SR_TIME64 = 28; // 4 regs + + wire COMPAT_NUM = 8'd2; + + wire wb_clk = clk_fpga; + wire wb_rst = rst_fpga; + + wire pps_int; + wire [63:0] vita_time; + reg [15:0] reg_leds, reg_cgen_ctrl, reg_test, xfer_rate; + + wire [7:0] set_addr; + wire [31:0] set_data; + wire set_stb; + + wire [31:0] debug_vt; + + // ///////////////////////////////////////////////////////////////////////////////////// + // GPMC Slave to Wishbone Master + localparam dw = 16; + localparam aw = 11; + localparam sw = 2; + + wire [dw-1:0] m0_dat_mosi, m0_dat_miso; + wire [aw-1:0] m0_adr; + wire [sw-1:0] m0_sel; + wire m0_cyc, m0_stb, m0_we, m0_ack, m0_err, m0_rty; + + wire [31:0] debug_gpmc; + + wire [35:0] tx_data, rx_data, tx_err_data; + wire tx_src_rdy, tx_dst_rdy, rx_src_rdy, rx_dst_rdy, + tx_err_src_rdy, tx_err_dst_rdy; + reg [15:0] tx_frame_len; + wire [15:0] rx_frame_len; + wire [7:0] rate; + + wire bus_error; + + wire clear_rx_int, clear_tx_int, clear_tx, clear_rx, do_clear; + + setting_reg #(.my_addr(SR_CLEAR_FIFO), .width(2)) sr_clear + (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr), + .in(set_data),.out({clear_tx_int,clear_rx_int}),.changed(do_clear)); + assign clear_tx = clear_tx_int & do_clear; + assign clear_rx = clear_rx_int & do_clear; + + gpmc_async #(.TXFIFOSIZE(TXFIFOSIZE), .RXFIFOSIZE(RXFIFOSIZE)) + gpmc (.arst(wb_rst), + .EM_CLK(EM_CLK), .EM_D(EM_D), .EM_A(EM_A), .EM_NBE(EM_NBE), + .EM_WAIT0(EM_WAIT0), .EM_NCS4(EM_NCS4), .EM_NCS6(EM_NCS6), .EM_NWE(EM_NWE), + .EM_NOE(EM_NOE), + + .rx_have_data(rx_have_data), .tx_have_space(tx_have_space), + .bus_error(bus_error), .bus_reset(0), + + .wb_clk(wb_clk), .wb_rst(wb_rst), + .wb_adr_o(m0_adr), .wb_dat_mosi(m0_dat_mosi), .wb_dat_miso(m0_dat_miso), + .wb_sel_o(m0_sel), .wb_cyc_o(m0_cyc), .wb_stb_o(m0_stb), .wb_we_o(m0_we), + .wb_ack_i(m0_ack), + + .fifo_clk(wb_clk), .fifo_rst(wb_rst), .clear_tx(clear_tx), .clear_rx(clear_rx), + .tx_data_o(tx_data), .tx_src_rdy_o(tx_src_rdy), .tx_dst_rdy_i(tx_dst_rdy), + .rx_data_i(rx_data), .rx_src_rdy_i(rx_src_rdy), .rx_dst_rdy_o(rx_dst_rdy), + + .tx_frame_len(tx_frame_len), .rx_frame_len(rx_frame_len), + .debug(debug_gpmc)); + + wire rx_sof = rx_data[32]; + wire rx_eof = rx_data[33]; + wire rx_src_rdy_int, rx_dst_rdy_int, tx_src_rdy_int, tx_dst_rdy_int; + +`ifdef LOOPBACK + wire [7:0] WHOAMI = 1; + + fifo_cascade #(.WIDTH(36), .SIZE(12)) loopback_fifo + (.clk(wb_clk), .reset(wb_rst), .clear(clear_tx | clear_rx), + .datain(tx_data), .src_rdy_i(tx_src_rdy), .dst_rdy_o(tx_dst_rdy), + .dataout(rx_data), .src_rdy_o(rx_src_rdy), .dst_rdy_i(rx_dst_rdy)); + + assign tx_underrun = 0; + assign rx_overrun = 0; + + wire run_tx, run_rx, strobe_tx, strobe_rx; +`endif // LOOPBACK + +`ifdef TIMED + wire [7:0] WHOAMI = 2; + + // TX side + wire tx_enable; + + fifo_pacer tx_pacer + (.clk(wb_clk), .reset(wb_rst), .rate(rate), .enable(tx_enable), + .src1_rdy_i(tx_src_rdy), .dst1_rdy_o(tx_dst_rdy), + .src2_rdy_o(tx_src_rdy_int), .dst2_rdy_i(tx_dst_rdy_int), + .underrun(tx_underrun), .overrun()); + + packet_verifier32 pktver32 + (.clk(wb_clk), .reset(wb_rst), .clear(clear_tx), + .data_i(tx_data), .src_rdy_i(tx_src_rdy_int), .dst_rdy_o(tx_dst_rdy_int), + .total(total), .crc_err(crc_err), .seq_err(seq_err), .len_err(len_err)); + + // RX side + wire rx_enable; + + packet_generator32 pktgen32 + (.clk(wb_clk), .reset(wb_rst), .clear(clear_rx), + .data_o(rx_data), .src_rdy_o(rx_src_rdy_int), .dst_rdy_i(rx_dst_rdy_int)); + + fifo_pacer rx_pacer + (.clk(wb_clk), .reset(wb_rst), .rate(rate), .enable(rx_enable), + .src1_rdy_i(rx_src_rdy_int), .dst1_rdy_o(rx_dst_rdy_int), + .src2_rdy_o(rx_src_rdy), .dst2_rdy_i(rx_dst_rdy), + .underrun(), .overrun(rx_overrun)); + +`endif // `ifdef TIMED + +`ifdef DSP + wire [7:0] WHOAMI = 0; + + wire [31:0] debug_rx_dsp, vrc_debug, vrf_debug; + + // ///////////////////////////////////////////////////////////////////////// + // DSP RX + wire [31:0] sample_rx, sample_tx; + wire strobe_rx, strobe_tx; + wire rx1_dst_rdy, rx1_src_rdy; + wire [99:0] rx1_data; + wire run_rx; + wire [35:0] vita_rx_data; + wire vita_rx_src_rdy, vita_rx_dst_rdy; + + dsp_core_rx #(.BASE(SR_RX_DSP)) dsp_core_rx + (.clk(wb_clk),.rst(wb_rst), + .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data), + .adc_a({rx_i,2'b0}),.adc_ovf_a(0),.adc_b({rx_q,2'b0}),.adc_ovf_b(0), + .sample(sample_rx), .run(run_rx), .strobe(strobe_rx), + .debug(debug_rx_dsp) ); + + vita_rx_control #(.BASE(SR_RX_CTRL), .WIDTH(32)) vita_rx_control + (.clk(wb_clk), .reset(wb_rst), .clear(clear_rx), + .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data), + .vita_time(vita_time), .overrun(rx_overrun), + .sample(sample_rx), .run(run_rx), .strobe(strobe_rx), + .sample_fifo_o(rx1_data), .sample_fifo_dst_rdy_i(rx1_dst_rdy), .sample_fifo_src_rdy_o(rx1_src_rdy), + .debug_rx(vrc_debug)); + + vita_rx_framer #(.BASE(SR_RX_CTRL), .MAXCHAN(1)) vita_rx_framer + (.clk(wb_clk), .reset(wb_rst), .clear(clear_rx), + .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data), + .sample_fifo_i(rx1_data), .sample_fifo_dst_rdy_o(rx1_dst_rdy), .sample_fifo_src_rdy_i(rx1_src_rdy), + .data_o(vita_rx_data), .dst_rdy_i(vita_rx_dst_rdy), .src_rdy_o(vita_rx_src_rdy), + .fifo_occupied(), .fifo_full(), .fifo_empty(), + .debug_rx(vrf_debug) ); + + fifo36_mux #(.prio(0)) mux_err_stream + (.clk(wb_clk), .reset(wb_rst), .clear(0), + .data0_i(vita_rx_data), .src0_rdy_i(vita_rx_src_rdy), .dst0_rdy_o(vita_rx_dst_rdy), + .data1_i(tx_err_data), .src1_rdy_i(tx_err_src_rdy), .dst1_rdy_o(tx_err_dst_rdy), + .data_o(rx_data), .src_rdy_o(rx_src_rdy), .dst_rdy_i(rx_dst_rdy)); + + // /////////////////////////////////////////////////////////////////////////////////// + // DSP TX + + wire [15:0] tx_i_int, tx_q_int; + wire run_tx; + + vita_tx_chain #(.BASE_CTRL(SR_TX_CTRL), .BASE_DSP(SR_TX_DSP), + .REPORT_ERROR(1), .PROT_ENG_FLAGS(0)) + vita_tx_chain + (.clk(wb_clk), .reset(wb_rst), + .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data), + .vita_time(vita_time), + .tx_data_i(tx_data), .tx_src_rdy_i(tx_src_rdy), .tx_dst_rdy_o(tx_dst_rdy), + .err_data_o(tx_err_data), .err_src_rdy_o(tx_err_src_rdy), .err_dst_rdy_i(tx_err_dst_rdy), + .dac_a(tx_i_int),.dac_b(tx_q_int), + .underrun(underrun), .run(run_tx), + .debug(debug_vt)); + + assign tx_i = tx_i_int[15:2]; + assign tx_q = tx_q_int[15:2]; + +`else // !`ifdef DSP + // Dummy DSP signal generator for test purposes + wire [23:0] tx_i_int, tx_q_int; + wire [23:0] freq = {reg_test,8'd0}; + reg [23:0] phase; + + always @(posedge wb_clk) + phase <= phase + freq; + + cordic_z24 #(.bitwidth(24)) tx_cordic + (.clock(wb_clk), .reset(wb_rst), .enable(1), + .xi(24'd2500000), .yi(24'd0), .zi(phase), .xo(tx_i_int), .yo(tx_q_int), .zo()); + + assign tx_i = tx_i_int[23:10]; + assign tx_q = tx_q_int[23:10]; +`endif // !`ifdef DSP + + // ///////////////////////////////////////////////////////////////////////////////////// + // Wishbone Intercon, single master + wire [dw-1:0] s0_dat_mosi, s1_dat_mosi, s0_dat_miso, s1_dat_miso, s2_dat_mosi, s3_dat_mosi, s2_dat_miso, s3_dat_miso, + s4_dat_mosi, s5_dat_mosi, s4_dat_miso, s5_dat_miso, s6_dat_mosi, s7_dat_mosi, s6_dat_miso, s7_dat_miso, + s8_dat_mosi, s9_dat_mosi, s8_dat_miso, s9_dat_miso, sa_dat_mosi, sb_dat_mosi, sa_dat_miso, sb_dat_miso, + sc_dat_mosi, sd_dat_mosi, sc_dat_miso, sd_dat_miso, se_dat_mosi, sf_dat_mosi, se_dat_miso, sf_dat_miso; + wire [aw-1:0] s0_adr,s1_adr,s2_adr,s3_adr,s4_adr,s5_adr,s6_adr,s7_adr; + wire [aw-1:0] s8_adr,s9_adr,sa_adr,sb_adr,sc_adr, sd_adr, se_adr, sf_adr; + wire [sw-1:0] s0_sel,s1_sel,s2_sel,s3_sel,s4_sel,s5_sel,s6_sel,s7_sel; + wire [sw-1:0] s8_sel,s9_sel,sa_sel,sb_sel,sc_sel, sd_sel, se_sel, sf_sel; + wire s0_ack,s1_ack,s2_ack,s3_ack,s4_ack,s5_ack,s6_ack,s7_ack; + wire s8_ack,s9_ack,sa_ack,sb_ack,sc_ack, sd_ack, se_ack, sf_ack; + wire s0_stb,s1_stb,s2_stb,s3_stb,s4_stb,s5_stb,s6_stb,s7_stb; + wire s8_stb,s9_stb,sa_stb,sb_stb,sc_stb, sd_stb, se_stb, sf_stb; + wire s0_cyc,s1_cyc,s2_cyc,s3_cyc,s4_cyc,s5_cyc,s6_cyc,s7_cyc; + wire s8_cyc,s9_cyc,sa_cyc,sb_cyc,sc_cyc, sd_cyc, se_cyc, sf_cyc; + wire s0_we,s1_we,s2_we,s3_we,s4_we,s5_we,s6_we,s7_we; + wire s8_we,s9_we,sa_we,sb_we,sc_we,sd_we, se_we, sf_we; + + wb_1master #(.dw(dw), .aw(aw), .sw(sw), .decode_w(4), + .s0_addr(4'h0), .s0_mask(4'hF), .s1_addr(4'h1), .s1_mask(4'hF), + .s2_addr(4'h2), .s2_mask(4'hF), .s3_addr(4'h3), .s3_mask(4'hF), + .s4_addr(4'h4), .s4_mask(4'hF), .s5_addr(4'h5), .s5_mask(4'hF), + .s6_addr(4'h6), .s6_mask(4'hF), .s7_addr(4'h7), .s7_mask(4'hF), + .s8_addr(4'h8), .s8_mask(4'hF), .s9_addr(4'h9), .s9_mask(4'hF), + .sa_addr(4'ha), .sa_mask(4'hF), .sb_addr(4'hb), .sb_mask(4'hF), + .sc_addr(4'hc), .sc_mask(4'hF), .sd_addr(4'hd), .sd_mask(4'hF), + .se_addr(4'he), .se_mask(4'hF), .sf_addr(4'hf), .sf_mask(4'hF)) + wb_1master + (.clk_i(wb_clk),.rst_i(wb_rst), + .m0_dat_o(m0_dat_miso),.m0_ack_o(m0_ack),.m0_err_o(m0_err),.m0_rty_o(m0_rty),.m0_dat_i(m0_dat_mosi), + .m0_adr_i(m0_adr),.m0_sel_i(m0_sel),.m0_we_i(m0_we),.m0_cyc_i(m0_cyc),.m0_stb_i(m0_stb), + .s0_dat_o(s0_dat_mosi),.s0_adr_o(s0_adr),.s0_sel_o(s0_sel),.s0_we_o(s0_we),.s0_cyc_o(s0_cyc),.s0_stb_o(s0_stb), + .s0_dat_i(s0_dat_miso),.s0_ack_i(s0_ack),.s0_err_i(0),.s0_rty_i(0), + .s1_dat_o(s1_dat_mosi),.s1_adr_o(s1_adr),.s1_sel_o(s1_sel),.s1_we_o(s1_we),.s1_cyc_o(s1_cyc),.s1_stb_o(s1_stb), + .s1_dat_i(s1_dat_miso),.s1_ack_i(s1_ack),.s1_err_i(0),.s1_rty_i(0), + .s2_dat_o(s2_dat_mosi),.s2_adr_o(s2_adr),.s2_sel_o(s2_sel),.s2_we_o(s2_we),.s2_cyc_o(s2_cyc),.s2_stb_o(s2_stb), + .s2_dat_i(s2_dat_miso),.s2_ack_i(s2_ack),.s2_err_i(0),.s2_rty_i(0), + .s3_dat_o(s3_dat_mosi),.s3_adr_o(s3_adr),.s3_sel_o(s3_sel),.s3_we_o(s3_we),.s3_cyc_o(s3_cyc),.s3_stb_o(s3_stb), + .s3_dat_i(s3_dat_miso),.s3_ack_i(s3_ack),.s3_err_i(0),.s3_rty_i(0), + .s4_dat_o(s4_dat_mosi),.s4_adr_o(s4_adr),.s4_sel_o(s4_sel),.s4_we_o(s4_we),.s4_cyc_o(s4_cyc),.s4_stb_o(s4_stb), + .s4_dat_i(s4_dat_miso),.s4_ack_i(s4_ack),.s4_err_i(0),.s4_rty_i(0), + .s5_dat_o(s5_dat_mosi),.s5_adr_o(s5_adr),.s5_sel_o(s5_sel),.s5_we_o(s5_we),.s5_cyc_o(s5_cyc),.s5_stb_o(s5_stb), + .s5_dat_i(s5_dat_miso),.s5_ack_i(s5_ack),.s5_err_i(0),.s5_rty_i(0), + .s6_dat_o(s6_dat_mosi),.s6_adr_o(s6_adr),.s6_sel_o(s6_sel),.s6_we_o(s6_we),.s6_cyc_o(s6_cyc),.s6_stb_o(s6_stb), + .s6_dat_i(s6_dat_miso),.s6_ack_i(s6_ack),.s6_err_i(0),.s6_rty_i(0), + .s7_dat_o(s7_dat_mosi),.s7_adr_o(s7_adr),.s7_sel_o(s7_sel),.s7_we_o(s7_we),.s7_cyc_o(s7_cyc),.s7_stb_o(s7_stb), + .s7_dat_i(s7_dat_miso),.s7_ack_i(s7_ack),.s7_err_i(0),.s7_rty_i(0), + .s8_dat_o(s8_dat_mosi),.s8_adr_o(s8_adr),.s8_sel_o(s8_sel),.s8_we_o(s8_we),.s8_cyc_o(s8_cyc),.s8_stb_o(s8_stb), + .s8_dat_i(s8_dat_miso),.s8_ack_i(s8_ack),.s8_err_i(0),.s8_rty_i(0), + .s9_dat_o(s9_dat_mosi),.s9_adr_o(s9_adr),.s9_sel_o(s9_sel),.s9_we_o(s9_we),.s9_cyc_o(s9_cyc),.s9_stb_o(s9_stb), + .s9_dat_i(s9_dat_miso),.s9_ack_i(s9_ack),.s9_err_i(0),.s9_rty_i(0), + .sa_dat_o(sa_dat_mosi),.sa_adr_o(sa_adr),.sa_sel_o(sa_sel),.sa_we_o(sa_we),.sa_cyc_o(sa_cyc),.sa_stb_o(sa_stb), + .sa_dat_i(sa_dat_miso),.sa_ack_i(sa_ack),.sa_err_i(0),.sa_rty_i(0), + .sb_dat_o(sb_dat_mosi),.sb_adr_o(sb_adr),.sb_sel_o(sb_sel),.sb_we_o(sb_we),.sb_cyc_o(sb_cyc),.sb_stb_o(sb_stb), + .sb_dat_i(sb_dat_miso),.sb_ack_i(sb_ack),.sb_err_i(0),.sb_rty_i(0), + .sc_dat_o(sc_dat_mosi),.sc_adr_o(sc_adr),.sc_sel_o(sc_sel),.sc_we_o(sc_we),.sc_cyc_o(sc_cyc),.sc_stb_o(sc_stb), + .sc_dat_i(sc_dat_miso),.sc_ack_i(sc_ack),.sc_err_i(0),.sc_rty_i(0), + .sd_dat_o(sd_dat_mosi),.sd_adr_o(sd_adr),.sd_sel_o(sd_sel),.sd_we_o(sd_we),.sd_cyc_o(sd_cyc),.sd_stb_o(sd_stb), + .sd_dat_i(sd_dat_miso),.sd_ack_i(sd_ack),.sd_err_i(0),.sd_rty_i(0), + .se_dat_o(se_dat_mosi),.se_adr_o(se_adr),.se_sel_o(se_sel),.se_we_o(se_we),.se_cyc_o(se_cyc),.se_stb_o(se_stb), + .se_dat_i(se_dat_miso),.se_ack_i(se_ack),.se_err_i(0),.se_rty_i(0), + .sf_dat_o(sf_dat_mosi),.sf_adr_o(sf_adr),.sf_sel_o(sf_sel),.sf_we_o(sf_we),.sf_cyc_o(sf_cyc),.sf_stb_o(sf_stb), + .sf_dat_i(sf_dat_miso),.sf_ack_i(sf_ack),.sf_err_i(0),.sf_rty_i(0) ); + + assign s7_ack = 0; + assign s8_ack = 0; assign s9_ack = 0; assign sa_ack = 0; assign sb_ack = 0; + assign sc_ack = 0; assign sd_ack = 0; assign se_ack = 0; assign sf_ack = 0; + + // ///////////////////////////////////////////////////////////////////////////////////// + // Slave 0, Misc LEDs, Switches, controls + + localparam REG_LEDS = 7'd0; // out + localparam REG_SWITCHES = 7'd2; // in + localparam REG_CGEN_CTRL = 7'd4; // out + localparam REG_CGEN_ST = 7'd6; // in + localparam REG_TEST = 7'd8; // out + localparam REG_RX_FRAMELEN = 7'd10; // in + localparam REG_TX_FRAMELEN = 7'd12; // out + localparam REG_XFER_RATE = 7'd14; // out + localparam REG_COMPAT = 7'd16; // in + + always @(posedge wb_clk) + if(wb_rst) + begin + reg_leds <= 0; + reg_cgen_ctrl <= 2'b11; + reg_test <= 0; + tx_frame_len <= 0; + xfer_rate <= 0; + end + else + if(s0_cyc & s0_stb & s0_we) + case(s0_adr[6:0]) + REG_LEDS : + reg_leds <= s0_dat_mosi; + REG_CGEN_CTRL : + reg_cgen_ctrl <= s0_dat_mosi; + REG_TEST : + reg_test <= s0_dat_mosi; + REG_TX_FRAMELEN : + tx_frame_len <= s0_dat_mosi; + REG_XFER_RATE : + xfer_rate <= s0_dat_mosi; + endcase // case (s0_adr[6:0]) + + assign tx_enable = xfer_rate[15]; + assign rx_enable = xfer_rate[14]; + assign rate = xfer_rate[7:0]; + + assign { debug_led[3:0] } = {run_rx,run_tx,reg_leds[1:0]}; + assign { cgen_sync_b, cgen_ref_sel } = reg_cgen_ctrl; + + assign s0_dat_miso = (s0_adr[6:0] == REG_LEDS) ? reg_leds : + (s0_adr[6:0] == REG_SWITCHES) ? { 16'd0 } : + (s0_adr[6:0] == REG_CGEN_CTRL) ? reg_cgen_ctrl : + (s0_adr[6:0] == REG_CGEN_ST) ? {13'b0,cgen_st_status,cgen_st_ld,cgen_st_refmon} : + (s0_adr[6:0] == REG_TEST) ? reg_test : + (s0_adr[6:0] == REG_RX_FRAMELEN) ? rx_frame_len : + (s0_adr[6:0] == REG_COMPAT) ? { WHOAMI, COMPAT_NUM } : + 16'hBEEF; + + assign s0_ack = s0_stb & s0_cyc; + + // ///////////////////////////////////////////////////////////////////////////////////// + // Slave 1, UART + // depth of 3 is 128 entries, clkdiv of 278 gives 230.4k with a 64 MHz system clock + + simple_uart #(.TXDEPTH(3),.RXDEPTH(3), .CLKDIV_DEFAULT(278)) uart + (.clk_i(wb_clk),.rst_i(wb_rst), + .we_i(s1_we),.stb_i(s1_stb),.cyc_i(s1_cyc),.ack_o(s1_ack), + .adr_i(s1_adr[3:1]),.dat_i({16'd0,s1_dat_mosi}),.dat_o(s1_dat_miso), + .rx_int_o(),.tx_int_o(), + .tx_o(debug_txd),.rx_i(debug_rxd),.baud_o()); + + // ///////////////////////////////////////////////////////////////////////////////////// + // Slave 2, SPI + + spi_top16 shared_spi + (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),.wb_adr_i(s2_adr[4:0]),.wb_dat_i(s2_dat_mosi), + .wb_dat_o(s2_dat_miso),.wb_sel_i(s2_sel),.wb_we_i(s2_we),.wb_stb_i(s2_stb), + .wb_cyc_i(s2_cyc),.wb_ack_o(s2_ack),.wb_err_o(),.wb_int_o(), + .ss_pad_o(sen), .sclk_pad_o(sclk), .mosi_pad_o(mosi), .miso_pad_i(miso) ); + + // ///////////////////////////////////////////////////////////////////////// + // Slave 3, I2C + + wire scl_pad_i, scl_pad_o, scl_pad_oen_o, sda_pad_i, sda_pad_o, sda_pad_oen_o; + i2c_master_top #(.ARST_LVL(1)) i2c + (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),.arst_i(1'b0), + .wb_adr_i(s3_adr[4:2]),.wb_dat_i(s3_dat_mosi[7:0]),.wb_dat_o(s3_dat_miso[7:0]), + .wb_we_i(s3_we),.wb_stb_i(s3_stb),.wb_cyc_i(s3_cyc), + .wb_ack_o(s3_ack),.wb_inta_o(), + .scl_pad_i(scl_pad_i),.scl_pad_o(scl_pad_o),.scl_padoen_o(scl_pad_oen_o), + .sda_pad_i(sda_pad_i),.sda_pad_o(sda_pad_o),.sda_padoen_o(sda_pad_oen_o) ); + + assign s3_dat_miso[15:8] = 8'd0; + + // I2C -- Don't use external transistors for open drain, the FPGA implements this + IOBUF scl_pin(.O(scl_pad_i), .IO(db_scl), .I(scl_pad_o), .T(scl_pad_oen_o)); + IOBUF sda_pin(.O(sda_pad_i), .IO(db_sda), .I(sda_pad_o), .T(sda_pad_oen_o)); + + // ///////////////////////////////////////////////////////////////////////// + // GPIOs -- Slave #4 + + wire [31:0] atr_lines; + wire [31:0] debug_gpio_0, debug_gpio_1; + + nsgpio16LE + nsgpio16LE(.clk_i(wb_clk),.rst_i(wb_rst), + .cyc_i(s4_cyc),.stb_i(s4_stb),.adr_i(s4_adr[3:0]),.we_i(s4_we), + .dat_i(s4_dat_mosi),.dat_o(s4_dat_miso),.ack_o(s4_ack), + .atr(atr_lines),.debug_0(debug_gpio_0),.debug_1(debug_gpio_1), + .gpio( {io_tx,io_rx} ) ); + + // ///////////////////////////////////////////////////////////////////////// + // Settings Bus -- Slave #5 + + // only have 32 regs, 32 bits each with current setup... + settings_bus_16LE #(.AWIDTH(11),.RWIDTH(11-4-2)) settings_bus_16LE + (.wb_clk(wb_clk),.wb_rst(wb_rst),.wb_adr_i(s5_adr),.wb_dat_i(s5_dat_mosi), + .wb_stb_i(s5_stb),.wb_we_i(s5_we),.wb_ack_o(s5_ack), + .strobe(set_stb),.addr(set_addr),.data(set_data) ); + + // ///////////////////////////////////////////////////////////////////////// + // ATR Controller -- Slave #6 + + atr_controller16 atr_controller16 + (.clk_i(wb_clk), .rst_i(wb_rst), + .adr_i(s6_adr), .sel_i(s6_sel), .dat_i(s6_dat_mosi), .dat_o(s6_dat_miso), + .we_i(s6_we), .stb_i(s6_stb), .cyc_i(s6_cyc), .ack_o(s6_ack), + .run_rx(run_rx), .run_tx(run_tx), .ctrl_lines(atr_lines)); + + + // ///////////////////////////////////////////////////////////////////////// + // VITA Timing + + time_64bit #(.TICKS_PER_SEC(32'd64000000),.BASE(SR_TIME64)) time_64bit + (.clk(wb_clk), .rst(wb_rst), .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data), + .pps(pps_in), .vita_time(vita_time), .pps_int(pps_int)); + + // ///////////////////////////////////////////////////////////////////////////////////// + // Debug circuitry + + assign debug_clk = { EM_CLK, clk_fpga }; + + assign debug = { { rx_have_data, tx_have_space, EM_NCS6, EM_NCS5, EM_NCS4, EM_NWE, EM_NOE, rx_overrun }, + { tx_src_rdy, tx_src_rdy_int, tx_dst_rdy, tx_dst_rdy_int, rx_src_rdy, rx_src_rdy_int, rx_dst_rdy, rx_dst_rdy_int }, + { EM_D } }; + + assign debug_gpio_0 = { {run_tx, strobe_tx, run_rx, strobe_rx, tx_i[11:0]}, + {2'b00, tx_src_rdy, tx_dst_rdy, tx_q[11:0]} }; + + assign debug_gpio_1 = debug_vt; + +/* + assign debug_gpio_1 = { {rx_enable, rx_src_rdy, rx_dst_rdy, rx_src_rdy & ~rx_dst_rdy}, + {tx_enable, tx_src_rdy, tx_dst_rdy, tx_dst_rdy & ~tx_src_rdy}, + {rx_sof, rx_eof, rx_src_rdy, rx_dst_rdy, rx_data[33:32],2'b0}, + {2'b0, bus_error, debug_gpmc[4:0] }, + {misc_gpio[7:0]} }; + */ +endmodule // u1e_core diff --git a/fpga/usrp2/top/u1e_ethdebug/.gitignore b/fpga/usrp2/top/u1e_ethdebug/.gitignore new file mode 100644 index 000000000..8d872713e --- /dev/null +++ b/fpga/usrp2/top/u1e_ethdebug/.gitignore @@ -0,0 +1,6 @@ +*~ +build +*.log +*.cmd +tb_u1e +*.lxt diff --git a/fpga/usrp2/top/u1e_ethdebug/Makefile b/fpga/usrp2/top/u1e_ethdebug/Makefile new file mode 100644 index 000000000..751b52970 --- /dev/null +++ b/fpga/usrp2/top/u1e_ethdebug/Makefile @@ -0,0 +1,83 @@ +# +# Copyright 2008 Ettus Research LLC +# + +################################################## +# Project Setup +################################################## +TOP_MODULE = u1e +BUILD_DIR = $(abspath build$(ISE)) + +################################################## +# Include other makefiles +################################################## + +include ../Makefile.common + +################################################## +# Project Properties +################################################## +export PROJECT_PROPERTIES := \ +family "Spartan-3A DSP" \ +device xc3sd1800a \ +package cs484 \ +speed -4 \ +top_level_module_type "HDL" \ +synthesis_tool "XST (VHDL/Verilog)" \ +simulator "ISE Simulator (VHDL/Verilog)" \ +"Preferred Language" "Verilog" \ +"Enable Message Filtering" FALSE \ +"Display Incremental Messages" FALSE + +################################################## +# Sources +################################################## +TOP_SRCS = \ +u1e.v \ +u1e.ucf + +SOURCES = $(abspath $(TOP_SRCS)) + +################################################## +# Process Properties +################################################## +SYNTHESIZE_PROPERTIES = \ +"Number of Clock Buffers" 8 \ +"Pack I/O Registers into IOBs" Yes \ +"Optimization Effort" High \ +"Optimize Instantiated Primitives" TRUE \ +"Register Balancing" Yes \ +"Use Clock Enable" Auto \ +"Use Synchronous Reset" Auto \ +"Use Synchronous Set" Auto + +TRANSLATE_PROPERTIES = \ +"Macro Search Path" "$(shell pwd)/../../coregen/" + +MAP_PROPERTIES = \ +"Allow Logic Optimization Across Hierarchy" TRUE \ +"Map to Input Functions" 4 \ +"Optimization Strategy (Cover Mode)" Speed \ +"Pack I/O Registers/Latches into IOBs" "For Inputs and Outputs" \ +"Perform Timing-Driven Packing and Placement" TRUE \ +"Map Effort Level" High \ +"Extra Effort" Normal \ +"Combinatorial Logic Optimization" TRUE \ +"Register Duplication" TRUE + +PLACE_ROUTE_PROPERTIES = \ +"Place & Route Effort Level (Overall)" High + +STATIC_TIMING_PROPERTIES = \ +"Number of Paths in Error/Verbose Report" 10 \ +"Report Type" "Error Report" + +GEN_PROG_FILE_PROPERTIES = \ +"Configuration Rate" 6 \ +"Create Binary Configuration File" TRUE \ +"Done (Output Events)" 5 \ +"Enable Bitstream Compression" TRUE \ +"Enable Outputs (Output Events)" 6 \ +"Unused IOB Pins" "Pull Up" + +SIM_MODEL_PROPERTIES = "" diff --git a/fpga/usrp2/top/u1e_ethdebug/u1e.ucf b/fpga/usrp2/top/u1e_ethdebug/u1e.ucf new file mode 100644 index 000000000..d6a2ea4ed --- /dev/null +++ b/fpga/usrp2/top/u1e_ethdebug/u1e.ucf @@ -0,0 +1,88 @@ + +## GPMC +NET "EM_D<15>" LOC = "D13" ; +NET "EM_D<14>" LOC = "D15" ; +NET "EM_D<13>" LOC = "C16" ; +NET "EM_D<12>" LOC = "B20" ; +NET "EM_D<11>" LOC = "A19" ; +NET "EM_D<10>" LOC = "A17" ; +NET "EM_D<9>" LOC = "E15" ; +NET "EM_D<8>" LOC = "F15" ; +NET "EM_D<7>" LOC = "E16" ; +NET "EM_D<6>" LOC = "F16" ; +NET "EM_D<5>" LOC = "B17" ; +NET "EM_D<4>" LOC = "C17" ; +NET "EM_D<3>" LOC = "B19" ; +NET "EM_D<2>" LOC = "D19" ; +NET "EM_D<1>" LOC = "C19" ; +NET "EM_D<0>" LOC = "A20" ; + +NET "EM_A<10>" LOC = "C14" ; +NET "EM_A<9>" LOC = "C10" ; +NET "EM_A<8>" LOC = "C5" ; +NET "EM_A<7>" LOC = "A18" ; +NET "EM_A<6>" LOC = "A15" ; +NET "EM_A<5>" LOC = "A12" ; +NET "EM_A<4>" LOC = "A10" ; +NET "EM_A<3>" LOC = "E7" ; +NET "EM_A<2>" LOC = "A7" ; +NET "EM_A<1>" LOC = "C15" ; + +NET "EM_NCS6" LOC = "E17" ; +NET "EM_NCS5" LOC = "E10" ; +NET "EM_NCS4" LOC = "E6" ; +#NET "EM_NCS1" LOC = "D18" ; +#NET "EM_NCS0" LOC = "D17" ; + +NET "EM_CLK" LOC = "F11" ; +NET "EM_WAIT0" LOC = "F14" ; +#NET "EM_NBE<1>" LOC = "D14" ; +#NET "EM_NBE<0>" LOC = "A13" ; +NET "EM_NWE" LOC = "B13" ; +NET "EM_NOE" LOC = "A14" ; +NET "EM_NADV_ALE" LOC = "B15" ; +#NET "EM_NWP" LOC = "F13" ; +NET "overo_gpio64" LOC = "A4" ; # nRESET +NET "overo_gpio176" LOC = "B4" ; # IRQ + +## Debug pins +NET "debug_led<3>" LOC = "Y15" ; +NET "debug_led<2>" LOC = "K16" ; +NET "debug_led<1>" LOC = "J17" ; +NET "debug_led<0>" LOC = "H22" ; +NET "debug<0>" LOC = "G22" ; +NET "debug<1>" LOC = "H17" ; +NET "debug<2>" LOC = "H18" ; +NET "debug<3>" LOC = "K20" ; +NET "debug<4>" LOC = "J20" ; +NET "debug<5>" LOC = "K19" ; +NET "debug<6>" LOC = "K18" ; +NET "debug<7>" LOC = "L22" ; +NET "debug<8>" LOC = "K22" ; +NET "debug<9>" LOC = "N22" ; +NET "debug<10>" LOC = "M22" ; +NET "debug<11>" LOC = "N20" ; +NET "debug<12>" LOC = "N19" ; +NET "debug<13>" LOC = "R22" ; +NET "debug<14>" LOC = "P22" ; +NET "debug<15>" LOC = "N17" ; +NET "debug<16>" LOC = "P16" ; +NET "debug<17>" LOC = "U22" ; +NET "debug<18>" LOC = "P19" ; +NET "debug<19>" LOC = "R18" ; +NET "debug<20>" LOC = "U20" ; +NET "debug<21>" LOC = "T20" ; +NET "debug<22>" LOC = "R19" ; +NET "debug<23>" LOC = "R20" ; +NET "debug<24>" LOC = "W22" ; +NET "debug<25>" LOC = "Y22" ; +NET "debug<26>" LOC = "T18" ; +NET "debug<27>" LOC = "T17" ; +NET "debug<28>" LOC = "W19" ; +NET "debug<29>" LOC = "V20" ; +NET "debug<30>" LOC = "Y21" ; +NET "debug<31>" LOC = "AA22" ; +NET "debug_clk<0>" LOC = "N18" ; +NET "debug_clk<1>" LOC = "M17" ; + +NET "debug_pb" LOC = "C22" ; diff --git a/fpga/usrp2/top/u1e_ethdebug/u1e.v b/fpga/usrp2/top/u1e_ethdebug/u1e.v new file mode 100644 index 000000000..2a543a313 --- /dev/null +++ b/fpga/usrp2/top/u1e_ethdebug/u1e.v @@ -0,0 +1,28 @@ +`timescale 1ns / 1ps +////////////////////////////////////////////////////////////////////////////////// + +//`define DCM 1 + +module u1e + (output [3:0] debug_led, output [31:0] debug, output [1:0] debug_clk, + input debug_pb, + + // GPMC + input EM_CLK, input [15:0] EM_D, input [10:1] EM_A, + input EM_WAIT0, input EM_NCS4, input EM_NCS5, input EM_NCS6, input EM_NWE, input EM_NOE, + input EM_NADV_ALE, + + input overo_gpio64, input overo_gpio176 + ); + + assign debug_clk = {EM_CLK, EM_NADV_ALE}; + + assign debug_led = {1'b0, EM_A[9], EM_A[8], debug_pb}; + + assign debug = { {overo_gpio64, overo_gpio176, EM_WAIT0, EM_NCS4, EM_NCS5, EM_NCS6, EM_NWE, EM_NOE }, + { EM_A[10], EM_A[7:1] }, + { EM_D[15:8] }, + { EM_D[7:0] } }; + + +endmodule // u1e diff --git a/fpga/usrp2/top/u1e_passthru/.gitignore b/fpga/usrp2/top/u1e_passthru/.gitignore new file mode 100644 index 000000000..1b2211df0 --- /dev/null +++ b/fpga/usrp2/top/u1e_passthru/.gitignore @@ -0,0 +1 @@ +build* diff --git a/fpga/usrp2/top/u1e_passthru/Makefile b/fpga/usrp2/top/u1e_passthru/Makefile new file mode 100644 index 000000000..d1950629b --- /dev/null +++ b/fpga/usrp2/top/u1e_passthru/Makefile @@ -0,0 +1,99 @@ +# +# Copyright 2008 Ettus Research LLC +# + +################################################## +# Project Setup +################################################## +TOP_MODULE = passthru +BUILD_DIR = $(abspath build$(ISE)) + +################################################## +# Include other makefiles +################################################## + +include ../Makefile.common +include ../../fifo/Makefile.srcs +include ../../control_lib/Makefile.srcs +include ../../sdr_lib/Makefile.srcs +include ../../serdes/Makefile.srcs +include ../../simple_gemac/Makefile.srcs +include ../../timing/Makefile.srcs +include ../../opencores/Makefile.srcs +include ../../vrt/Makefile.srcs +include ../../udp/Makefile.srcs +include ../../coregen/Makefile.srcs +include ../../extram/Makefile.srcs +include ../../gpmc/Makefile.srcs + +################################################## +# Project Properties +################################################## +export PROJECT_PROPERTIES := \ +family "Spartan-3A DSP" \ +device xc3sd1800a \ +package cs484 \ +speed -4 \ +top_level_module_type "HDL" \ +synthesis_tool "XST (VHDL/Verilog)" \ +simulator "ISE Simulator (VHDL/Verilog)" \ +"Preferred Language" "Verilog" \ +"Enable Message Filtering" FALSE \ +"Display Incremental Messages" FALSE + +################################################## +# Sources +################################################## +TOP_SRCS = \ +passthru.v \ +passthru.ucf + +SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \ +$(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \ +$(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \ +$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS) \ +$(GPMC_SRCS) + +################################################## +# Process Properties +################################################## +SYNTHESIZE_PROPERTIES = \ +"Number of Clock Buffers" 8 \ +"Pack I/O Registers into IOBs" Yes \ +"Optimization Effort" High \ +"Optimize Instantiated Primitives" TRUE \ +"Register Balancing" Yes \ +"Use Clock Enable" Auto \ +"Use Synchronous Reset" Auto \ +"Use Synchronous Set" Auto + +TRANSLATE_PROPERTIES = \ +"Macro Search Path" "$(shell pwd)/../../coregen/" + +MAP_PROPERTIES = \ +"Allow Logic Optimization Across Hierarchy" TRUE \ +"Map to Input Functions" 4 \ +"Optimization Strategy (Cover Mode)" Speed \ +"Pack I/O Registers/Latches into IOBs" "For Inputs and Outputs" \ +"Perform Timing-Driven Packing and Placement" TRUE \ +"Map Effort Level" High \ +"Extra Effort" Normal \ +"Combinatorial Logic Optimization" TRUE \ +"Register Duplication" TRUE + +PLACE_ROUTE_PROPERTIES = \ +"Place & Route Effort Level (Overall)" High + +STATIC_TIMING_PROPERTIES = \ +"Number of Paths in Error/Verbose Report" 10 \ +"Report Type" "Error Report" + +GEN_PROG_FILE_PROPERTIES = \ +"Configuration Rate" 6 \ +"Create Binary Configuration File" TRUE \ +"Done (Output Events)" 5 \ +"Enable Bitstream Compression" TRUE \ +"Enable Outputs (Output Events)" 6 \ +"Unused IOB Pins" "Pull Up" + +SIM_MODEL_PROPERTIES = "" diff --git a/fpga/usrp2/top/u1e_passthru/passthru.ucf b/fpga/usrp2/top/u1e_passthru/passthru.ucf new file mode 100644 index 000000000..64e6f0440 --- /dev/null +++ b/fpga/usrp2/top/u1e_passthru/passthru.ucf @@ -0,0 +1,6 @@ +NET "overo_gpio145" LOC = "C7" ; +NET "cgen_mosi" LOC = "E22" ; +NET "cgen_sclk" LOC = "J19" ; +NET "cgen_sen_b" LOC = "H20" ; +NET "fpga_cfg_din" LOC = "W17" ; +NET "fpga_cfg_cclk" LOC = "V17" ; diff --git a/fpga/usrp2/top/u1e_passthru/passthru.v b/fpga/usrp2/top/u1e_passthru/passthru.v new file mode 100644 index 000000000..12e4db017 --- /dev/null +++ b/fpga/usrp2/top/u1e_passthru/passthru.v @@ -0,0 +1,18 @@ +`timescale 1ns / 1ps +////////////////////////////////////////////////////////////////////////////////// + +module passthru + (input overo_gpio145, + output cgen_sclk, + output cgen_sen_b, + output cgen_mosi, + input fpga_cfg_din, + input fpga_cfg_cclk + ); + + assign cgen_sclk = fpga_cfg_cclk; + assign cgen_sen_b = overo_gpio145; + assign cgen_mosi = fpga_cfg_din; + + +endmodule // passthru diff --git a/host/CMakeLists.txt b/host/CMakeLists.txt index a60eed0a5..e5ce78782 100644 --- a/host/CMakeLists.txt +++ b/host/CMakeLists.txt @@ -16,7 +16,7 @@ # CMAKE_MINIMUM_REQUIRED(VERSION 2.6) -PROJECT(UHD CXX) +PROJECT(UHD CXX C) ENABLE_TESTING() ######################################################################## @@ -64,7 +64,7 @@ IF(CMAKE_COMPILER_IS_GNUCXX) #causes trouble when compiling libusb1.0 on macintosh #comment out until mac ports libusb gets its act together #ADD_DEFINITIONS(-pedantic) - ADD_DEFINITIONS(-ansi) + #ADD_DEFINITIONS(-ansi) #only export symbols that are declared to be part of the uhd api: UHD_ADD_OPTIONAL_CXX_COMPILER_FLAG(-fvisibility=hidden HAVE_VISIBILITY_HIDDEN) ENDIF(CMAKE_COMPILER_IS_GNUCXX) diff --git a/host/apps/omap_debug/.gitignore b/host/apps/omap_debug/.gitignore new file mode 100644 index 000000000..008a23138 --- /dev/null +++ b/host/apps/omap_debug/.gitignore @@ -0,0 +1,20 @@ +.gitignore +clkgen-config +fpga-downloader +usrp-e-button +usrp-e-crc-rw +usrp-e-ctl +usrp-e-debug-pins +usrp-e-fpga-rw +usrp-e-gpio +usrp-e-i2c +usrp-e-lb-test +usrp-e-led +usrp-e-loopback +usrp-e-random-loopback +usrp-e-rw +usrp-e-spi +usrp-e-timed +usrp-e-uart +usrp-e-uart-rx +usrp-e-mm-loopback diff --git a/host/apps/omap_debug/Makefile b/host/apps/omap_debug/Makefile new file mode 100644 index 000000000..46d4714a8 --- /dev/null +++ b/host/apps/omap_debug/Makefile @@ -0,0 +1,61 @@ +CFLAGS=-Wall -I../../lib/usrp/usrp_e/ -march=armv7-a -mtune=cortex-a8 -mfpu=neon -O3 +CXXFLAGS=-Wall -I../../lib/usrp/usrp_e/ -march=armv7-a -mtune=cortex-a8 -mfpu=neon -O3 + +all : usrp-e-spi usrp-e-i2c usrp-e-loopback usrp-e-mm-loopback usrp-e-uart usrp-e-led usrp-e-ctl usrp-e-button usrp-e-uart-rx fpga-downloader usrp-e-gpio usrp-e-debug-pins usrp-e-random-loopback usrp-e-timed usrp-e-lb-test usrp-e-crc-rw clkgen-config + +usrp-e-spi : usrp-e-spi.c + +usrp-e-i2c : usrp-e-i2c.c + +usrp-e-loopback : usrp-e-loopback.c + gcc -o $@ $< -lpthread ${CFLAGS} + +usrp-e-mm-loopback : usrp-e-mm-loopback.c + gcc -o $@ $< -lpthread ${CFLAGS} + +usrp-e-timed : usrp-e-timed.c + gcc -o $@ $< -lpthread ${CFLAGS} + +usrp-e-random-loopback : usrp-e-random-loopback.c + gcc -o $@ $< -lpthread ${CFLAGS} + +usrp-e-crc-rw : usrp-e-crc-rw.c + gcc -o $@ $< -lpthread ${CFLAGS} + +usrp-e-uart : usrp-e-uart.c + +usrp-e-uart-rx : usrp-e-uart-rx.c + +usrp-e-led : usrp-e-led.c + +usrp-e-ctl : usrp-e-ctl.c + +usrp-e-button : usrp-e-button.c + +fpga-downloader : fpga-downloader.cc + +clkgen-config : clkgen-config.cc + +usrp-e-gpio : usrp-e-gpio.c + +usrp-e-lb-test : usrp-e-lb-test.c + +usrp-e-debug-pins : usrp-e-debug-pins.c +clean : + rm -f usrp-e-spi + rm -f usrp-e-i2c + rm -f usrp-e-loopback + rm -f usrp-e-mm-loopback + rm -f usrp-e-timed + rm -f usrp-e-rw-random + rm -f usrp-e-uart + rm -f usrp-e-uart-rx + rm -f usrp-e-led + rm -f usrp-e-ctl + rm -f usrp-e-button + rm -f fpga-downloader + rm -f usrp-e-gpio + rm -f usrp-e-debug-pins + rm -f usrp-e-lb-test + rm -f usrp-e-crc-rw + rm -f clkgen-config diff --git a/host/apps/omap_debug/README b/host/apps/omap_debug/README new file mode 100644 index 000000000..bbe0c2cc4 --- /dev/null +++ b/host/apps/omap_debug/README @@ -0,0 +1 @@ +OMAP development tools go here diff --git a/host/apps/omap_debug/clkgen-config.cc b/host/apps/omap_debug/clkgen-config.cc new file mode 100644 index 000000000..e8279b4ae --- /dev/null +++ b/host/apps/omap_debug/clkgen-config.cc @@ -0,0 +1,296 @@ +/* -*- c++ -*- */ +/* + * Copyright 2003,2004,2008,2009 Free Software Foundation, Inc. + * + * This file is part of UHD + * + * GNU Radio is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 3, or (at your option) + * any later version. + * + * GNU Radio is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with GNU Radio; see the file COPYING. If not, write to + * the Free Software Foundation, Inc., 51 Franklin Street, + * Boston, MA 02110-1301, USA. +*/ + +#include <iostream> +#include <sstream> +#include <fstream> +#include <string> +#include <cstdlib> + +#include <fcntl.h> +#include <sys/types.h> +#include <sys/stat.h> +#include <sys/ioctl.h> + +#include <linux/spi/spidev.h> + + +// Programming data for clock gen chip +static const unsigned int config_data[] = { + 0x000024, + 0x023201, + 0x000081, + 0x000400, + 0x00104c, + 0x001101, + 0x001200, + 0x001300, + 0x001414, + 0x001500, + 0x001604, + 0x001704, + 0x001807, + 0x001900, + //0x001a00,//for debug + 0x001a32, + 0x001b12, + 0x001c44, + 0x001d00, + 0x001e00, + 0x00f062, + 0x00f162, + 0x00f262, + 0x00f362, + 0x00f462, + 0x00f562, + 0x00f662, + 0x00f762, + 0x00f862, + 0x00f962, + 0x00fa62, + 0x00fb62, + 0x00fc00, + 0x00fd00, + 0x019021, + 0x019100, + 0x019200, + 0x019333, + 0x019400, + 0x019500, + 0x019611, + 0x019700, + 0x019800, + 0x019900, + 0x019a00, + 0x019b00, + 0x01e003, + 0x01e102, + 0x023000, + 0x023201, + 0x0b0201, + 0x0b0300, + 0x001fff, + 0x0a0000, + 0x0a0100, + 0x0a0200, + 0x0a0302, + 0x0a0400, + 0x0a0504, + 0x0a060e, + 0x0a0700, + 0x0a0810, + 0x0a090e, + 0x0a0a00, + 0x0a0bf0, + 0x0a0c0b, + 0x0a0d01, + 0x0a0e90, + 0x0a0f01, + 0x0a1001, + 0x0a11e0, + 0x0a1201, + 0x0a1302, + 0x0a1430, + 0x0a1580, + 0x0a16ff, + 0x023201, + 0x0b0301, + 0x023201, +}; + + +const unsigned int CLKGEN_SELECT = 145; + + +enum gpio_direction {IN, OUT}; + +class gpio { + public: + + gpio(unsigned int gpio_num, gpio_direction pin_direction, bool close_action); + ~gpio(); + + bool get_value(); + void set_value(bool state); + + private: + + unsigned int gpio_num; + + std::stringstream base_path; + std::fstream value_file; + std::fstream direction_file; + bool close_action; // True set to input and release, false do nothing +}; + +class spidev { + public: + + spidev(std::string dev_name); + ~spidev(); + + void send(char *wbuf, char *rbuf, unsigned int nbytes); + + private: + + int fd; + +}; + +gpio::gpio(unsigned int _gpio_num, gpio_direction pin_direction, bool close_action) +{ + std::fstream export_file; + + gpio_num = _gpio_num; + + export_file.open("/sys/class/gpio/export", std::ios::out); + if (!export_file.is_open()) ///\todo Poor error handling + std::cout << "Failed to open gpio export file." << std::endl; + + export_file << gpio_num << std::endl; + + base_path << "/sys/class/gpio/gpio" << gpio_num << std::flush; + + std::string direction_file_name; + + direction_file_name = base_path.str() + "/direction"; + + direction_file.open(direction_file_name.c_str()); + if (!direction_file.is_open()) + std::cout << "Failed to open direction file." << std::endl; + if (pin_direction == OUT) + direction_file << "out" << std::endl; + else + direction_file << "in" << std::endl; + + std::string value_file_name; + + value_file_name = base_path.str() + "/value"; + + value_file.open(value_file_name.c_str(), std::ios_base::in | std::ios_base::out); + if (!value_file.is_open()) + std::cout << "Failed to open value file." << std::endl; +} + +bool gpio::get_value() +{ + + std::string val; + + std::getline(value_file, val); + value_file.seekg(0); + + if (val == "0") + return false; + else if (val == "1") + return true; + else + std::cout << "Data read from value file|" << val << "|" << std::endl; + + return false; +} + +void gpio::set_value(bool state) +{ + + if (state) + value_file << "1" << std::endl; + else + value_file << "0" << std::endl; +} + +gpio::~gpio() +{ + if (close_action) { + std::fstream unexport_file; + + direction_file << "in" << std::endl; + + unexport_file.open("/sys/class/gpio/unexport", std::ios::out); + if (!unexport_file.is_open()) ///\todo Poor error handling + std::cout << "Failed to open gpio export file." << std::endl; + + unexport_file << gpio_num << std::endl; + + } + +} + +spidev::spidev(std::string fname) +{ + int ret; + int mode = 0; + int speed = 12000; + int bits = 24; + + fd = open(fname.c_str(), O_RDWR); + + ret = ioctl(fd, SPI_IOC_WR_MODE, &mode); + ret = ioctl(fd, SPI_IOC_WR_MAX_SPEED_HZ, &speed); + ret = ioctl(fd, SPI_IOC_WR_BITS_PER_WORD, &bits); +} + + +spidev::~spidev() +{ + close(fd); +} + +void spidev::send(char *buf, char *rbuf, unsigned int nbytes) +{ + int ret; + + struct spi_ioc_transfer tr; + tr.tx_buf = (unsigned long) buf; + tr.rx_buf = (unsigned long) rbuf; + tr.len = nbytes; + tr.delay_usecs = 0; + tr.speed_hz = 12000000; + tr.bits_per_word = 24; + + ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr); + +} + +static void send_config_to_clkgen(gpio &chip_select, const unsigned int data[], unsigned int data_size) +{ + spidev spi("/dev/spidev1.0"); + unsigned int rbuf; + + for (unsigned int i = 0; i < data_size; i++) { + + std::cout << "sending " << std::hex << data[i] << std::endl; + chip_select.set_value(0); + spi.send((char *)&data[i], (char *)&rbuf, 4); + chip_select.set_value(1); + + }; +} + +int main(int argc, char *argv[]) +{ + + gpio clkgen_select(CLKGEN_SELECT, OUT, true); + + send_config_to_clkgen(clkgen_select, config_data, sizeof(config_data)/sizeof(unsigned int)); +} + diff --git a/host/apps/omap_debug/fetch-bin.sh b/host/apps/omap_debug/fetch-bin.sh new file mode 100755 index 000000000..019ddaaf2 --- /dev/null +++ b/host/apps/omap_debug/fetch-bin.sh @@ -0,0 +1,6 @@ +if [ $GHQ ]; then + scp $GHQ_USER@astro:/workspace/usrp1-e-dev/u1e.bin /home/root +else + scp -P 8822 balister@192.168.1.10:src/git/fpgapriv/usrp2/top/u1e/build/u1e.bin /home/root +fi +sync diff --git a/host/apps/omap_debug/fetch-kernel.sh b/host/apps/omap_debug/fetch-kernel.sh new file mode 100755 index 000000000..ce420f3d2 --- /dev/null +++ b/host/apps/omap_debug/fetch-kernel.sh @@ -0,0 +1,7 @@ +if [ $GHQ ]; then + scp $GHQ_USER@astro:/workspace/usrp1-e-dev/kernel_usrp/arch/arm/boot/uImage /media/mmcblk0p1/uImage +else + scp balister@192.168.1.10:src/git/kernel_usrp/arch/arm/boot/uImage /media/mmcblk0p1/uImage +fi +sync + diff --git a/host/apps/omap_debug/fetch-module.sh b/host/apps/omap_debug/fetch-module.sh new file mode 100755 index 000000000..ec28989bd --- /dev/null +++ b/host/apps/omap_debug/fetch-module.sh @@ -0,0 +1,6 @@ +if [ $GHQ ]; then + scp $GHQ_USER@astro:/workspace/usrp1-e-dev/kernel_usrp/drivers/misc/usrp_e.ko /lib/modules/2.6.33/kernel/drivers/misc +else + scp balister@192.168.1.10:src/git/kernel_usrp/drivers/misc/usrp_e.ko /lib/modules/2.6.33/kernel/drivers/misc +fi +sync diff --git a/host/apps/omap_debug/fetch-u-boot.sh b/host/apps/omap_debug/fetch-u-boot.sh new file mode 100755 index 000000000..5309364b8 --- /dev/null +++ b/host/apps/omap_debug/fetch-u-boot.sh @@ -0,0 +1,7 @@ +if [ $GHQ ]; then + scp $GHQ_USER@astro:/workspace/usrp1-e-dev/u-boot-overo/u-boot.bin /media/mmcblk0p1/ +else + scp balister@192.168.1.167:src/git/u-boot/u-boot.bin /media/mmcblk0p1/ +fi +sync + diff --git a/host/apps/omap_debug/fpga-downloader.cc b/host/apps/omap_debug/fpga-downloader.cc new file mode 100644 index 000000000..4e475b5c1 --- /dev/null +++ b/host/apps/omap_debug/fpga-downloader.cc @@ -0,0 +1,253 @@ +/* -*- c++ -*- */ +/* + * Copyright 2003,2004,2008,2009 Free Software Foundation, Inc. + * + * This file is part of GNU Radio + * + * GNU Radio is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 3, or (at your option) + * any later version. + * + * GNU Radio is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with GNU Radio; see the file COPYING. If not, write to + * the Free Software Foundation, Inc., 51 Franklin Street, + * Boston, MA 02110-1301, USA. +*/ + +#include <iostream> +#include <sstream> +#include <fstream> +#include <string> +#include <cstdlib> + +#include <fcntl.h> +#include <sys/types.h> +#include <sys/stat.h> +#include <sys/ioctl.h> + +#include <linux/spi/spidev.h> + +/* + * Configuration connections + * + * CCK - MCSPI1_CLK + * DIN - MCSPI1_MOSI + * PROG_B - GPIO_175 - output (change mux) + * DONE - GPIO_173 - input (change mux) + * INIT_B - GPIO_114 - input (change mux) + * +*/ + +const unsigned int PROG_B = 175; +const unsigned int DONE = 173; +const unsigned int INIT_B = 114; + +static std::string bit_file = "safe_u1e.bin"; + +const int BUF_SIZE = 4096; + +enum gpio_direction {IN, OUT}; + +class gpio { + public: + + gpio(unsigned int gpio_num, gpio_direction pin_direction); + + bool get_value(); + void set_value(bool state); + + private: + + std::stringstream base_path; + std::fstream value_file; +}; + +class spidev { + public: + + spidev(std::string dev_name); + ~spidev(); + + void send(char *wbuf, char *rbuf, unsigned int nbytes); + + private: + + int fd; + +}; + +gpio::gpio(unsigned int gpio_num, gpio_direction pin_direction) +{ + std::fstream export_file; + + export_file.open("/sys/class/gpio/export", std::ios::out); + if (!export_file.is_open()) ///\todo Poor error handling + std::cout << "Failed to open gpio export file." << std::endl; + + export_file << gpio_num << std::endl; + + base_path << "/sys/class/gpio/gpio" << gpio_num << std::flush; + + std::fstream direction_file; + std::string direction_file_name; + + if (gpio_num != 114) { + direction_file_name = base_path.str() + "/direction"; + + direction_file.open(direction_file_name.c_str()); + if (!direction_file.is_open()) + std::cout << "Failed to open direction file." << std::endl; + if (pin_direction == OUT) + direction_file << "out" << std::endl; + else + direction_file << "in" << std::endl; + } + + std::string value_file_name; + + value_file_name = base_path.str() + "/value"; + + value_file.open(value_file_name.c_str(), std::ios_base::in | std::ios_base::out); + if (!value_file.is_open()) + std::cout << "Failed to open value file." << std::endl; +} + +bool gpio::get_value() +{ + + std::string val; + + std::getline(value_file, val); + value_file.seekg(0); + + if (val == "0") + return false; + else if (val == "1") + return true; + else + std::cout << "Data read from value file|" << val << "|" << std::endl; + + return false; +} + +void gpio::set_value(bool state) +{ + + if (state) + value_file << "1" << std::endl; + else + value_file << "0" << std::endl; +} + +static void prepare_fpga_for_configuration(gpio &prog, gpio &init) +{ + + prog.set_value(true); + prog.set_value(false); + prog.set_value(true); + +#if 0 + bool ready_to_program(false); + unsigned int count(0); + do { + ready_to_program = init.get_value(); + count++; + + sleep(1); + } while (count < 10 && !ready_to_program); + + if (count == 10) { + std::cout << "FPGA not ready for programming." << std::endl; + exit(-1); + } +#endif +} + +spidev::spidev(std::string fname) +{ + int ret; + int mode = 0; + int speed = 12000000; + int bits = 8; + + fd = open(fname.c_str(), O_RDWR); + + ret = ioctl(fd, SPI_IOC_WR_MODE, &mode); + ret = ioctl(fd, SPI_IOC_WR_MAX_SPEED_HZ, &speed); + ret = ioctl(fd, SPI_IOC_WR_BITS_PER_WORD, &bits); +} + + +spidev::~spidev() +{ + close(fd); +} + +void spidev::send(char *buf, char *rbuf, unsigned int nbytes) +{ + int ret; + + struct spi_ioc_transfer tr; + tr.tx_buf = (unsigned long) buf; + tr.rx_buf = (unsigned long) rbuf; + tr.len = nbytes; + tr.delay_usecs = 0; + tr.speed_hz = 48000000; + tr.bits_per_word = 8; + + ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr); + +} + +static void send_file_to_fpga(std::string &file_name, gpio &error, gpio &done) +{ + std::ifstream bitstream; + + std::cout << "File name - " << file_name.c_str() << std::endl; + + bitstream.open(file_name.c_str(), std::ios::binary); + if (!bitstream.is_open()) + std::cout << "File " << file_name << " not opened succesfully." << std::endl; + + spidev spi("/dev/spidev1.0"); + char buf[BUF_SIZE]; + char rbuf[BUF_SIZE]; + + do { + bitstream.read(buf, BUF_SIZE); + spi.send(buf, rbuf, bitstream.gcount()); + + if (error.get_value()) + std::cout << "INIT_B went high, error occured." << std::endl; + + if (!done.get_value()) + std::cout << "Configuration complete." << std::endl; + + } while (bitstream.gcount() == BUF_SIZE); +} + +int main(int argc, char *argv[]) +{ + + gpio gpio_prog_b(PROG_B, OUT); + gpio gpio_init_b(INIT_B, IN); + gpio gpio_done (DONE, IN); + + if (argc == 2) + bit_file = argv[1]; + + std::cout << "FPGA config file: " << bit_file << std::endl; + + prepare_fpga_for_configuration(gpio_prog_b, gpio_init_b); + + std::cout << "Done = " << gpio_done.get_value() << std::endl; + + send_file_to_fpga(bit_file, gpio_init_b, gpio_done); +} + diff --git a/host/apps/omap_debug/read_board_id.sh b/host/apps/omap_debug/read_board_id.sh new file mode 100755 index 000000000..96081f219 --- /dev/null +++ b/host/apps/omap_debug/read_board_id.sh @@ -0,0 +1,10 @@ +#!/bin/sh + +i2cget -y 3 0x51 0x00 b +i2cget -y 3 0x51 0x01 b +i2cget -y 3 0x51 0x02 b +i2cget -y 3 0x51 0x03 b +i2cget -y 3 0x51 0x04 b +i2cget -y 3 0x51 0x05 b + + diff --git a/host/apps/omap_debug/reload-fpga.sh b/host/apps/omap_debug/reload-fpga.sh new file mode 100755 index 000000000..2754718a4 --- /dev/null +++ b/host/apps/omap_debug/reload-fpga.sh @@ -0,0 +1,7 @@ +#!/bin/sh + +rmmod usrp_e +fpga-downloader /home/root/u1e.bin +modprobe usrp_e +usrp-e-debug-pins 1 + diff --git a/host/apps/omap_debug/set_debug_pins.py b/host/apps/omap_debug/set_debug_pins.py new file mode 100755 index 000000000..0f9ecd7b9 --- /dev/null +++ b/host/apps/omap_debug/set_debug_pins.py @@ -0,0 +1,35 @@ +#!/usr/bin/python + +import os + +# Memory Map +misc_base = 0 +uart_base = 1 +spi_base = 2 +i2c_base = 3 +gpio_base = 4 * 128 +settings_base = 5 + +# GPIO offset +gpio_pins = 0 +gpio_ddr = 4 +gpio_ctrl_lo = 8 +gpio_ctrl_hi = 12 + +def set_reg(reg, val): + os.system("./usrp1-e-ctl w %d 1 %d" % (reg,val)) + +def get_reg(reg): + fin,fout = os.popen4("./usrp1-e-ctl r %d 1" % (reg,)) + print fout.read() + +# Set DDRs to output +set_reg(gpio_base+gpio_ddr, 0xFFFF) +set_reg(gpio_base+gpio_ddr+2, 0xFFFF) + +# Set CTRL to Debug #0 ( A is for debug 0, F is for debug 1 ) +set_reg(gpio_base+gpio_ctrl_lo, 0xAAAA) +set_reg(gpio_base+gpio_ctrl_lo+2, 0xAAAA) +set_reg(gpio_base+gpio_ctrl_hi, 0xAAAA) +set_reg(gpio_base+gpio_ctrl_hi+2, 0xAAAA) + diff --git a/host/apps/omap_debug/setup-board-id-eeprom.sh b/host/apps/omap_debug/setup-board-id-eeprom.sh new file mode 100755 index 000000000..4dba1cce5 --- /dev/null +++ b/host/apps/omap_debug/setup-board-id-eeprom.sh @@ -0,0 +1,17 @@ +#!/bin/sh + +i2cset -y 3 0x51 0x00 0x00 +i2cset -y 3 0x51 0x01 0x03 +i2cset -y 3 0x51 0x02 0x00 +i2cset -y 3 0x51 0x03 0x01 +i2cset -y 3 0x51 0x04 0x01 +i2cset -y 3 0x51 0x05 0x00 +i2cset -y 3 0x51 0x06 0x00 + +i2cget -y 3 0x51 0 b +i2cget -y 3 0x51 1 b +i2cget -y 3 0x51 2 b +i2cget -y 3 0x51 3 b +i2cget -y 3 0x51 4 b +i2cget -y 3 0x51 5 b +i2cget -y 3 0x51 6 b diff --git a/host/apps/omap_debug/test.c b/host/apps/omap_debug/test.c new file mode 100644 index 000000000..36f4d700a --- /dev/null +++ b/host/apps/omap_debug/test.c @@ -0,0 +1,34 @@ +#include <stdio.h> + +void +main() +{ + int x; + char *y; + long long z; + + x = 0x01020304; + z = 0x0102030405060708LL; + + printf("%x\n",x); + y = (char *)&x; + printf("%x\n",y[0]); + printf("%x\n",y[1]); + printf("%x\n",y[2]); + printf("%x\n",y[3]); + + printf("Printing z ...\n"); + printf("%llx\n",z); + printf("Printing z done\n"); + + y = (char *)&z; + printf("%x\n",y[0]); + printf("%x\n",y[1]); + printf("%x\n",y[2]); + printf("%x\n",y[3]); + printf("%x\n",y[4]); + printf("%x\n",y[5]); + printf("%x\n",y[6]); + printf("%x\n",y[7]); +} + diff --git a/host/apps/omap_debug/u1e-read-stream.c b/host/apps/omap_debug/u1e-read-stream.c new file mode 100644 index 000000000..4e4c21d9e --- /dev/null +++ b/host/apps/omap_debug/u1e-read-stream.c @@ -0,0 +1,21 @@ +#include <stdio.h> +#include <sys/types.h> +#include <fcntl.h> + +int main(int rgc, char *argv[]) +{ + int fp, cnt, n; + short buf[1024]; + + n = 0; + + fp = open("/dev/usrp1_e0", O_RDONLY); + printf("fp = %d\n", fp); + + do { + cnt = read(fp, buf, 2048); + n++; +// printf("Bytes read - %d\n", cnt); + } while(n < 10*512); + printf("Data - %hX\n", buf[0]); +} diff --git a/host/apps/omap_debug/usrp-e-button.c b/host/apps/omap_debug/usrp-e-button.c new file mode 100644 index 000000000..f13291491 --- /dev/null +++ b/host/apps/omap_debug/usrp-e-button.c @@ -0,0 +1,56 @@ +#include <stdio.h> +#include <stdlib.h> +#include <sys/types.h> +#include <fcntl.h> +#include <string.h> +#include <sys/ioctl.h> +#include <unistd.h> + +#include "usrp_e.h" +#include "usrp_e_regs.hpp" + +// Usage: usrp_e_uart <string> + +#define PB1 (1<<8) +#define PB2 (1<<9) +#define PB3 (1<<10) +#define P1 (0) +#define P2 (0xFF) +#define P3 (0xAA) +#define P4 (0x55) + +int main(int argc, char *argv[]) +{ + int fp, ret; + struct usrp_e_ctl16 d; + int pb1=0, pb2=0, pb3=0, p1=0, p2=0, p3=0, p4=0; + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + + d.offset = UE_REG_MISC_SW; + d.count = 1; + + do { + ret = ioctl(fp, USRP_E_READ_CTL16, &d); + if (d.buf[0] & PB1) { + pb1 = 1; + printf("Pushbutton 1 hit\n"); + } + + if (d.buf[0] & PB2) { + pb2 = 1; + printf("Pushbutton 2 hit\n"); + } + + if (d.buf[0] & PB3) { + pb3 = 1; + printf("Pushbutton 3 hit\n"); + } + + sleep(1); + + } while (!(pb1 && pb2 && pb3)); + + return 0; +} diff --git a/host/apps/omap_debug/usrp-e-crc-rw.c b/host/apps/omap_debug/usrp-e-crc-rw.c new file mode 100644 index 000000000..c3ae45cc1 --- /dev/null +++ b/host/apps/omap_debug/usrp-e-crc-rw.c @@ -0,0 +1,274 @@ +#include <stdio.h> +#include <sys/types.h> +#include <sys/time.h> +#include <sys/ioctl.h> +#include <string.h> +#include <fcntl.h> +#include <pthread.h> +#include <stdlib.h> +#include <unistd.h> +#include <stddef.h> +#include "usrp_e.h" + +// max length #define PKT_DATA_LENGTH 1016 +static int packet_data_length; + +static int fp; +static u_int32_t crc_tab[256]; + +// CRC code from http://www.koders.com/c/fid699AFE0A656F0022C9D6B9D1743E697B69CE5815.aspx +// GPLv2 + +static u_int32_t chksum_crc32_gentab(void) +{ + unsigned long crc, poly; + unsigned long i, j; + + poly = 0xEDB88320L; + + for (i = 0; i < 256; i++) { + crc = i; + for (j = 8; j > 0; j--) { + if (crc & 1) { + crc = (crc >> 1) ^ poly; + } else { + crc >>= 1; + } + } + crc_tab[i] = crc; + } + + return 0; +} + +static void *read_thread(void *threadid) +{ + int cnt; + struct usrp_transfer_frame *rx_data; + int rx_pkt_cnt; + int i; + unsigned long crc; + unsigned int rx_crc; + unsigned long bytes_transfered, elapsed_seconds; + struct timeval start_time, finish_time; + + __u8 *p; + __u32 *pi; + + printf("Greetings from the reading thread!\n"); + + // IMPORTANT: must assume max length packet from fpga + rx_data = malloc(2048); + + rx_pkt_cnt = 0; + + bytes_transfered = 0; + gettimeofday(&start_time, NULL); + + while (1) { + + cnt = read(fp, rx_data, 2048); + if (cnt < 0) + printf("Error returned from read: %d\n", cnt); + + rx_pkt_cnt++; + +#if 0 + if (rx_pkt_cnt == 512) { + printf("."); + fflush(stdout); + rx_pkt_cnt = 0; + } +#endif + + if (rx_data->status & RB_OVERRUN) + printf("O"); + + printf("rx_data->len = %d\n", rx_data->len); + + + crc = 0xFFFFFFFF; + for (i = 0; i < rx_data->len - 4; i+=2) { + crc = ((crc >> 8) & 0x00FFFFFF) ^ + crc_tab[(crc ^ rx_data->buf[i+1]) & 0xFF]; +printf("idx = %d, data = %X, crc = %X\n", i, rx_data->buf[i+1],crc); + crc = ((crc >> 8) & 0x00FFFFFF) ^ + crc_tab[(crc ^ rx_data->buf[i]) & 0xFF]; +printf("idx = %d, data = %X, crc = %X\n", i, rx_data->buf[i],crc); + } + + p = &rx_data->buf[rx_data->len - 4]; + pi = (__u32 *) p; + rx_crc = *pi; + +#if 1 + printf("rx_data->len = %d\n", rx_data->len); + printf("rx_data->status = %d\n", rx_data->status); + for (i = 0; i < rx_data->len; i++) + printf("idx = %d, data = %X\n", i, rx_data->buf[i]); + printf("calc crc = %lX, rx crc = %X\n", crc, rx_crc); + fflush(stdout); + break; +#endif + + if (rx_crc != (crc & 0xFFFFFFFF)) { + printf("CRC Error, calc crc: %X, rx_crc: %X\n", + (crc & 0xFFFFFFFF), rx_crc); + } + + bytes_transfered += rx_data->len; + + if (bytes_transfered > (100 * 1000000)) { + gettimeofday(&finish_time, NULL); + elapsed_seconds = finish_time.tv_sec - start_time.tv_sec; + + printf("Bytes transfered = %ld, elapsed seconds = %ld\n", bytes_transfered, elapsed_seconds); + printf("RX data transfer rate = %f K Samples/second\n", + (float) bytes_transfered / (float) elapsed_seconds / 250); + + + start_time = finish_time; + bytes_transfered = 0; + } + } +} + +static void *write_thread(void *threadid) +{ + int seq_number, i, cnt, tx_pkt_cnt; + int tx_len; + unsigned long crc; + struct usrp_transfer_frame *tx_data; + unsigned long bytes_transfered, elapsed_seconds; + struct timeval start_time, finish_time; + + printf("Greetings from the write thread!\n"); + + tx_pkt_cnt = 0; + tx_data = malloc(2048); + + bytes_transfered = 0; + gettimeofday(&start_time, NULL); + + while (1) { + + tx_pkt_cnt++; + +#if 0 + if (tx_pkt_cnt == 512) { + printf("."); + fflush(stdout); + } + if (tx_pkt_cnt == 1024) { + printf("'"); + fflush(stdout); + } + if (tx_pkt_cnt == 1536) { + printf(":"); + fflush(stdout); + tx_pkt_cnt = 0; + } +#endif + + tx_len = 2048 - sizeof(struct usrp_transfer_frame) - sizeof(int); + tx_data->len = tx_len + sizeof(int); + + crc = 0xFFFFFFFF; + for (i = 0; i < tx_len; i++) { + tx_data->buf[i] = i & 0xFF; + + crc = ((crc >> 8) & 0x00FFFFFF) ^ + crc_tab[(crc ^ tx_data->buf[i]) & 0xFF]; + + } + *((int *) &tx_data[tx_len]) = crc; + + cnt = write(fp, tx_data, 2048); + if (cnt < 0) + printf("Error returned from write: %d\n", cnt); + + + bytes_transfered += tx_data->len; + + if (bytes_transfered > (100 * 1000000)) { + gettimeofday(&finish_time, NULL); + elapsed_seconds = finish_time.tv_sec - start_time.tv_sec; + + printf("Bytes transfered = %d, elapsed seconds = %d\n", bytes_transfered, elapsed_seconds); + printf("TX data transfer rate = %f K Samples/second\n", + (float) bytes_transfered / (float) elapsed_seconds / 250); + + + start_time = finish_time; + bytes_transfered = 0; + } + +// sleep(1); + } +} + + +int main(int argc, char *argv[]) +{ + pthread_t tx, rx; + long int t; + int fpga_config_flag ,decimation; + struct usrp_e_ctl16 d; + struct sched_param s = { + .sched_priority = 1 + }; + + if (argc < 4) { + printf("%s t|w|rw decimation data_size\n", argv[0]); + return -1; + } + + chksum_crc32_gentab(); + + decimation = atoi(argv[2]); + packet_data_length = atoi(argv[3]); + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + + fpga_config_flag = 0; + if (strcmp(argv[1], "w") == 0) + fpga_config_flag |= (1 << 15); + else if (strcmp(argv[1], "r") == 0) + fpga_config_flag |= (1 << 14); + else if (strcmp(argv[1], "rw") == 0) + fpga_config_flag |= ((1 << 15) | (1 << 14)); + + fpga_config_flag |= decimation; + + d.offset = 14; + d.count = 1; + d.buf[0] = fpga_config_flag; + ioctl(fp, USRP_E_WRITE_CTL16, &d); + + sleep(1); // in case the kernel threads need time to start. FIXME if so + + sched_setscheduler(0, SCHED_RR, &s); + + if (fpga_config_flag & (1 << 14)) { + if (pthread_create(&rx, NULL, read_thread, (void *) t)) { + printf("Failed to create rx thread\n"); + exit(-1); + } + } + + sleep(1); + + if (fpga_config_flag & (1 << 15)) { + if (pthread_create(&tx, NULL, write_thread, (void *) t)) { + printf("Failed to create tx thread\n"); + exit(-1); + } + } + + sleep(10000); + + printf("Done sleeping\n"); + + return 0; +} diff --git a/host/apps/omap_debug/usrp-e-ctl.c b/host/apps/omap_debug/usrp-e-ctl.c new file mode 100644 index 000000000..69c48ee6f --- /dev/null +++ b/host/apps/omap_debug/usrp-e-ctl.c @@ -0,0 +1,48 @@ +#include <stdio.h> +#include <stdlib.h> +#include <sys/types.h> +#include <fcntl.h> +#include <sys/ioctl.h> + +#include "usrp_e.h" + +// Usage: usrp_e_ctl w|r offset number_of_values val1 val2 .... + +int main(int argc, char *argv[]) +{ + int fp, i, cnt, ret; + struct usrp_e_ctl16 ctl_data; + + if (argc < 4) { + printf("Usage: usrp_e_ctl w|r offset number_of_values val1 val2 ....\n"); + exit(-1); + } + + cnt = atoi(argv[3]); + + ctl_data.offset = atoi(argv[2]); + ctl_data.count = cnt; + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + + if (*argv[1] == 'w') { + for (i=0; i<cnt; i++) + ctl_data.buf[i] = atoi(argv[4+i]); + + ret = ioctl(fp, USRP_E_WRITE_CTL16, &ctl_data); + printf("Return value from write ioctl = %d\n", ret); + } + + if (*argv[1] == 'r') { + ret = ioctl(fp, USRP_E_READ_CTL16, &ctl_data); + printf("Return value from write ioctl = %d\n", ret); + + for (i=0; i<ctl_data.count; i++) { + if (!(i%8)) + printf("\nData at %4d :", i); + printf(" %5d", ctl_data.buf[i]); + } + printf("\n"); + } +} diff --git a/host/apps/omap_debug/usrp-e-debug-pins.c b/host/apps/omap_debug/usrp-e-debug-pins.c new file mode 100644 index 000000000..d18bbf990 --- /dev/null +++ b/host/apps/omap_debug/usrp-e-debug-pins.c @@ -0,0 +1,77 @@ +#include <stdio.h> +#include <stdlib.h> +#include <unistd.h> +#include <sys/types.h> +#include <fcntl.h> +#include <string.h> +#include <sys/ioctl.h> + +#include "usrp_e.h" +#include "usrp_e_regs.hpp" + +// Usage: usrp_e_gpio <string> + +static int fp; + +static int read_reg(__u16 reg) +{ + int ret; + struct usrp_e_ctl16 d; + + d.offset = reg; + d.count = 1; + ret = ioctl(fp, USRP_E_READ_CTL16, &d); + return d.buf[0]; +} + +static void write_reg(__u16 reg, __u16 val) +{ + int ret; + struct usrp_e_ctl16 d; + + d.offset = reg; + d.count = 1; + d.buf[0] = val; + ret = ioctl(fp, USRP_E_WRITE_CTL16, &d); +} + +int main(int argc, char *argv[]) +{ + int test; + + test = 0; + if (argc < 2) { + printf("%s 0|1|off\n", argv[0]); + } + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + if (fp < 0) { + perror("Open failed"); + return -1; + } + + if (strcmp(argv[1], "0") == 0) { + printf("Selected 0 based on %s\n", argv[1]); + write_reg(UE_REG_GPIO_TX_DDR, 0xFFFF); + write_reg(UE_REG_GPIO_RX_DDR, 0xFFFF); + write_reg(UE_REG_GPIO_TX_SEL, 0x0); + write_reg(UE_REG_GPIO_RX_SEL, 0x0); + write_reg(UE_REG_GPIO_TX_DBG, 0xFFFF); + write_reg(UE_REG_GPIO_RX_DBG, 0xFFFF); + } else if (strcmp(argv[1], "1") == 0) { + printf("Selected 1 based on %s\n", argv[1]); + write_reg(UE_REG_GPIO_TX_DDR, 0xFFFF); + write_reg(UE_REG_GPIO_RX_DDR, 0xFFFF); + write_reg(UE_REG_GPIO_TX_SEL, 0xFFFF); + write_reg(UE_REG_GPIO_RX_SEL, 0xFFFF); + write_reg(UE_REG_GPIO_TX_DBG, 0xFFFF); + write_reg(UE_REG_GPIO_RX_DBG, 0xFFFF); + } else { + printf("Selected off based on %s\n", argv[1]); + write_reg(UE_REG_GPIO_TX_DDR, 0x0); + write_reg(UE_REG_GPIO_RX_DDR, 0x0); + } + + return 0; +} diff --git a/host/apps/omap_debug/usrp-e-gpio.c b/host/apps/omap_debug/usrp-e-gpio.c new file mode 100644 index 000000000..adef877d3 --- /dev/null +++ b/host/apps/omap_debug/usrp-e-gpio.c @@ -0,0 +1,83 @@ +#include <stdio.h> +#include <stdlib.h> +#include <unistd.h> +#include <sys/types.h> +#include <fcntl.h> +#include <string.h> +#include <sys/ioctl.h> + +#include "usrp_e.h" +#include "usrp_e_regs.hpp" + +// Usage: usrp_e_gpio <string> + +static int fp; + +static int read_reg(__u16 reg) +{ + int ret; + struct usrp_e_ctl16 d; + + d.offset = reg; + d.count = 1; + ret = ioctl(fp, USRP_E_READ_CTL16, &d); + return d.buf[0]; +} + +static void write_reg(__u16 reg, __u16 val) +{ + int ret; + struct usrp_e_ctl16 d; + + d.offset = reg; + d.count = 1; + d.buf[0] = val; + ret = ioctl(fp, USRP_E_WRITE_CTL16, &d); +} + +int main(int argc, char *argv[]) +{ + int i, test, data_in; + + test = 0; + if (argc > 1) + test = 1; + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + + write_reg(UE_REG_GPIO_TX_DDR, 0x0); + write_reg(UE_REG_GPIO_RX_DDR, 0xFFFF); + + for (i=0; i < 16; i++) { + write_reg(UE_REG_GPIO_RX_IO, 1 << i); + sleep(1); + if (test) { + data_in = read_reg(UE_REG_GPIO_TX_IO); + if (data_in != (1 << i)) + printf("Read failed, wrote: %X read: %X\n", \ + 1 << i, data_in); + } + } + + write_reg(UE_REG_GPIO_RX_DDR, 0x0); + write_reg(UE_REG_GPIO_TX_DDR, 0xFFFF); + + sleep(1); + + for (i=0; i < 16; i++) { + write_reg(UE_REG_GPIO_TX_IO, 1 << i); + sleep(1); + if (test) { + data_in = read_reg(UE_REG_GPIO_RX_IO); + if (data_in != (1 << i)) + printf("Read failed, wrote: %X read: %X\n", \ + 1 << i, data_in); + } + } + + write_reg(UE_REG_GPIO_RX_DDR, 0x0); + write_reg(UE_REG_GPIO_TX_DDR, 0x0); + + return 0; +} diff --git a/host/apps/omap_debug/usrp-e-i2c.c b/host/apps/omap_debug/usrp-e-i2c.c new file mode 100644 index 000000000..da8709ae1 --- /dev/null +++ b/host/apps/omap_debug/usrp-e-i2c.c @@ -0,0 +1,87 @@ +#include <stdio.h> +#include <stdlib.h> +#include <string.h> +#include <unistd.h> +#include <sys/types.h> +#include <fcntl.h> +#include <sys/ioctl.h> + +#include "usrp_e.h" + +// Usage: usrp_e_i2c w address data0 data1 data 2 .... +// Usage: usrp_e_i2c r address count + +int main(int argc, char *argv[]) +{ + int fp, ret, i, tmp; + struct usrp_e_i2c *i2c_msg; + int direction, address, count; + + if (argc < 3) { + printf("Usage: usrp-e-i2c w address data0 data1 data2 ...\n"); + printf("Usage: usrp-e-i2c r address count\n"); + printf("All addresses and data in hex.\n"); + exit(-1); + } + + if (strcmp(argv[1], "r") == 0) { + direction = 0; + } else if (strcmp(argv[1], "w") == 0) { + direction = 1; + } else { + return -1; + } + + sscanf(argv[2], "%X", &address); + printf("Address = %X\n", address); + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + if (fp < 0) { + perror("Open failed"); + return -1; + } + +// sleep(1); + + if (direction) { + count = argc - 3; + } else { + sscanf(argv[3], "%X", &count); + } + printf("Count = %X\n", count); + + i2c_msg = malloc(sizeof(i2c_msg) + count * sizeof(char)); + + i2c_msg->addr = address; + i2c_msg->len = count; + + for (i = 0; i < count; i++) { + i2c_msg->data[i] = i; + } + + if (direction) { + // Write + + for (i=0; i<count; i++) { + sscanf(argv[3+i], "%X", &tmp); + i2c_msg->data[i] = tmp; + } + + ret = ioctl(fp, USRP_E_I2C_WRITE, i2c_msg); + printf("Return value from i2c_write ioctl: %d\n", ret); + } else { + // Read + + ret = ioctl(fp, USRP_E_I2C_READ, i2c_msg); + printf("Return value from i2c_read ioctl: %d\n", ret); + + printf("Ioctl: %d Data read :", ret); + for (i=0; i<count; i++) { + printf(" %X", i2c_msg->data[i]); + } + printf("\n"); + + } + return 0; +} diff --git a/host/apps/omap_debug/usrp-e-lb-test.c b/host/apps/omap_debug/usrp-e-lb-test.c new file mode 100644 index 000000000..68848064e --- /dev/null +++ b/host/apps/omap_debug/usrp-e-lb-test.c @@ -0,0 +1,58 @@ +#include <stdio.h> +#include <sys/types.h> +#include <fcntl.h> +#include <pthread.h> +#include <stdlib.h> +#include <unistd.h> +#include <stddef.h> +#include "usrp_e.h" + +// max length #define PKT_DATA_LENGTH 1016 + +int main(int argc, char *argv[]) +{ + struct usrp_transfer_frame *tx_data, *rx_data; + int i, fp, packet_data_length, cnt; + struct usrp_e_ctl16 d; + + if (argc < 2) { + printf("%s data_size (in bytes < 2040)\n", argv[0]); + return -1; + } + + packet_data_length = atoi(argv[1]); + + fp = open("/dev/usrp_e0", O_RDWR); + + d.offset = 14; + d.count = 1; + d.buf[0] = (1 << 13); + ioctl(fp, USRP_E_WRITE_CTL16, &d); + + tx_data = malloc(2048); + rx_data = malloc(2048); + + tx_data->status = 0; + tx_data->len = sizeof(struct usrp_transfer_frame) + packet_data_length; + + while (1) { + + for (i = 0; i < packet_data_length; i++) { + tx_data->buf[i] = random() >> 24; + + } + + cnt = write(fp, tx_data, 2048); + cnt = read(fp, rx_data, 2048); + + if (tx_data->len != rx_data->len) + printf("Bad frame length sent %d, read %d\n", tx_data->len, rx_data->len); + + for (i = 0; i < packet_data_length; i++) { + if (tx_data->buf[i] != rx_data->buf[i]) + printf("Bad data at %d, sent %d, received %d\n", i, tx_data->buf[i], rx_data->buf[i]); + } + printf("---------------------------------------------------\n"); + sleep(1); + } +} diff --git a/host/apps/omap_debug/usrp-e-led.c b/host/apps/omap_debug/usrp-e-led.c new file mode 100644 index 000000000..d1b6c8996 --- /dev/null +++ b/host/apps/omap_debug/usrp-e-led.c @@ -0,0 +1,35 @@ +#include <stdio.h> +#include <stdlib.h> +#include <sys/types.h> +#include <fcntl.h> +#include <string.h> +#include <sys/ioctl.h> +#include <unistd.h> + +#include "usrp_e.h" +#include "usrp_e_regs.hpp" + +// Usage: usrp_e_uart <string> + + +int main(int argc, char *argv[]) +{ + int fp, i, ret; + struct usrp_e_ctl16 d; + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + + d.offset = UE_REG_MISC_BASE; + d.count = 1; + + while (1) { + for (i=0; i<8; i++) { + d.buf[0] = i; + ret = ioctl(fp, USRP_E_WRITE_CTL16, &d); + sleep(1); + } + } + + return 0; +} diff --git a/host/apps/omap_debug/usrp-e-loopback.c b/host/apps/omap_debug/usrp-e-loopback.c new file mode 100644 index 000000000..d11cf7d09 --- /dev/null +++ b/host/apps/omap_debug/usrp-e-loopback.c @@ -0,0 +1,194 @@ +#include <stdio.h> +#include <sys/types.h> +#include <fcntl.h> +#include <pthread.h> +#include <stdlib.h> +#include <unistd.h> +#include <stddef.h> +#include <sys/mman.h> +#include "usrp_e.h" + +// max length #define PKT_DATA_LENGTH 1016 +static int packet_data_length; +static int error; + +struct pkt { + int len; + int checksum; + int seq_num; + short data[]; +}; + +static int fp; + +static int calc_checksum(struct pkt *p) +{ + int i, sum; + + i = 0; + sum = 0; + + for (i=0; i < p->len; i++) + sum += p->data[i]; + + sum += p->seq_num; + sum += p->len; + + return sum; +} + +static void *read_thread(void *threadid) +{ + char *rx_data; + int cnt, prev_seq_num, pkt_count, seq_num_failure; + struct pkt *p; + unsigned long bytes_transfered, elapsed_seconds; + struct timeval start_time, finish_time; + + printf("Greetings from the reading thread!\n"); + + bytes_transfered = 0; + gettimeofday(&start_time, NULL); + + // IMPORTANT: must assume max length packet from fpga + rx_data = malloc(2048); + p = (struct pkt *) ((void *)rx_data); + + prev_seq_num = 0; + pkt_count = 0; + seq_num_failure = 0; + + while (1) { + + cnt = read(fp, rx_data, 2048); + if (cnt < 0) + printf("Error returned from read: %d, sequence number = %d\n", cnt, p->seq_num); + +// printf("p->seq_num = %d\n", p->seq_num); + + + pkt_count++; + + if (p->seq_num != prev_seq_num + 1) { + printf("Sequence number fail, current = %d, previous = %d, pkt_count = %d\n", + p->seq_num, prev_seq_num, pkt_count); + + seq_num_failure ++; + if (seq_num_failure > 2) + error = 1; + } + + prev_seq_num = p->seq_num; + + if (calc_checksum(p) != p->checksum) { + printf("Checksum fail packet = %X, expected = %X, pkt_count = %d\n", + calc_checksum(p), p->checksum, pkt_count); + error = 1; + } + + bytes_transfered += cnt; + + if (bytes_transfered > (100 * 1000000)) { + gettimeofday(&finish_time, NULL); + elapsed_seconds = finish_time.tv_sec - start_time.tv_sec; + + printf("RX data transfer rate = %f K Samples/second\n", + (float) bytes_transfered / (float) elapsed_seconds / 4000); + + + start_time = finish_time; + bytes_transfered = 0; + } + + +// printf("."); +// fflush(stdout); +// printf("\n"); + } + +} + +static void *write_thread(void *threadid) +{ + int seq_number, i, cnt; + void *tx_data; + struct pkt *p; + + printf("Greetings from the write thread!\n"); + + tx_data = malloc(2048); + p = (struct pkt *) ((void *)tx_data); + + for (i=0; i < packet_data_length; i++) +// p->data[i] = random() >> 16; + p->data[i] = i; + + seq_number = 1; + + while (1) { + p->seq_num = seq_number++; + + if (packet_data_length > 0) + p->len = packet_data_length; + else + p->len = (random() & 0x1ff) + (1004 - 512); + + p->checksum = calc_checksum(p); + + cnt = write(fp, tx_data, p->len * 2 + 12); + if (cnt < 0) + printf("Error returned from write: %d\n", cnt); +// sleep(1); + } +} + + +int main(int argc, char *argv[]) +{ + pthread_t tx, rx; + long int t; + struct sched_param s = { + .sched_priority = 1 + }; + void *rb; + struct usrp_transfer_frame *tx_rb, *rx_rb; + + if (argc < 2) { + printf("%s data_size\n", argv[0]); + return -1; + } + + packet_data_length = atoi(argv[1]); + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + + rb = mmap(0, 202 * 4096, PROT_READ|PROT_WRITE, MAP_SHARED, fp, 0); + if (!rb) { + printf("mmap failed\n"); + exit; + } + + + sched_setscheduler(0, SCHED_RR, &s); + error = 0; + +#if 1 + if (pthread_create(&rx, NULL, read_thread, (void *) t)) { + printf("Failed to create rx thread\n"); + exit(-1); + } + + sleep(1); +#endif + + if (pthread_create(&tx, NULL, write_thread, (void *) t)) { + printf("Failed to create tx thread\n"); + exit(-1); + } + +// while (!error) + sleep(1000000000); + + printf("Done sleeping\n"); +} diff --git a/host/apps/omap_debug/usrp-e-mm-loopback.c b/host/apps/omap_debug/usrp-e-mm-loopback.c new file mode 100644 index 000000000..f5fc83c87 --- /dev/null +++ b/host/apps/omap_debug/usrp-e-mm-loopback.c @@ -0,0 +1,258 @@ +#include <stdio.h> +#include <sys/types.h> +#include <sys/ioctl.h> +#include <fcntl.h> +#include <pthread.h> +#include <stdlib.h> +#include <unistd.h> +#include <stddef.h> +#include <sys/mman.h> +#include <poll.h> +#include "usrp_e.h" + +// max length #define PKT_DATA_LENGTH 1016 +static int packet_data_length; +static int error; + +struct pkt { + int len; + int checksum; + int seq_num; + short data[1024-6]; +}; + +struct ring_buffer_info (*rxi)[]; +struct ring_buffer_info (*txi)[]; +struct pkt (*rx_buf)[200]; +struct pkt (*tx_buf)[200]; + +static int fp; +static struct usrp_e_ring_buffer_size_t rb_size; + +static int calc_checksum(struct pkt *p) +{ + int i, sum; + + i = 0; + sum = 0; + + for (i=0; i < p->len; i++) + sum += p->data[i]; + + sum += p->seq_num; + sum += p->len; + + return sum; +} + +static void *read_thread(void *threadid) +{ + int cnt, prev_seq_num, pkt_count, seq_num_failure; + struct pkt *p; + unsigned long bytes_transfered, elapsed_seconds; + struct timeval start_time, finish_time; + int rb_read; + + printf("Greetings from the reading thread!\n"); + printf("sizeof pkt = %d\n", sizeof(struct pkt)); + + rb_read = 0; + + bytes_transfered = 0; + gettimeofday(&start_time, NULL); + + prev_seq_num = 0; + pkt_count = 0; + seq_num_failure = 0; + + while (1) { + + if (!((*rxi)[rb_read].flags & RB_USER)) { +// printf("Waiting for data\n"); + struct pollfd pfd; + pfd.fd = fp; + pfd.events = POLLIN; + ssize_t ret = poll(&pfd, 1, -1); + } + +// printf("pkt received, rb_read = %d\n", rb_read); + + cnt = (*rxi)[rb_read].len; + p = &(*rx_buf)[rb_read]; + +// cnt = read(fp, rx_data, 2048); +// if (cnt < 0) +// printf("Error returned from read: %d, sequence number = %d\n", cnt, p->seq_num); + +// printf("p = %X, p->seq_num = %d p->len = %d\n", p, p->seq_num, p->len); + + + pkt_count++; + + if (p->seq_num != prev_seq_num + 1) { + printf("Sequence number fail, current = %d, previous = %d, pkt_count = %d\n", + p->seq_num, prev_seq_num, pkt_count); + printf("pkt received, rb_read = %d\n", rb_read); + printf("p = %X, p->seq_num = %d p->len = %d\n", p, p->seq_num, p->len); + + seq_num_failure ++; + if (seq_num_failure > 2) + error = 1; + } + + prev_seq_num = p->seq_num; + + if (calc_checksum(p) != p->checksum) { + printf("Checksum fail packet = %X, expected = %X, pkt_count = %d\n", + calc_checksum(p), p->checksum, pkt_count); + error = 1; + } + + (*rxi)[rb_read].flags = RB_KERNEL; + + rb_read++; + if (rb_read == rb_size.num_rx_frames) + rb_read = 0; + + bytes_transfered += cnt; + + if (bytes_transfered > (100 * 1000000)) { + gettimeofday(&finish_time, NULL); + elapsed_seconds = finish_time.tv_sec - start_time.tv_sec; + + printf("RX data transfer rate = %f K Samples/second\n", + (float) bytes_transfered / (float) elapsed_seconds / 4000); + + + start_time = finish_time; + bytes_transfered = 0; + } + + +// printf("."); +// fflush(stdout); +// printf("\n"); + } + +} + +static void *write_thread(void *threadid) +{ + int seq_number, i, cnt, rb_write; + void *tx_data; + struct pkt *p; + + printf("Greetings from the write thread!\n"); + + tx_data = malloc(2048); + p = (struct pkt *) ((void *)tx_data); + + for (i=0; i < packet_data_length; i++) +// p->data[i] = random() >> 16; + p->data[i] = i; + + seq_number = 1; + rb_write = 0; + + while (1) { + p->seq_num = seq_number++; + + if (packet_data_length > 0) + p->len = packet_data_length; + else + p->len = (random() & 0x1ff) + (1004 - 512); + + p->checksum = calc_checksum(p); + + if (!((*txi)[rb_write].flags & RB_KERNEL)) { +// printf("Waiting for space\n"); + struct pollfd pfd; + pfd.fd = fp; + pfd.events = POLLOUT; + ssize_t ret = poll(&pfd, 1, -1); + } + + memcpy(&(*tx_buf)[rb_write], tx_data, p->len * 2 + 12); + + (*txi)[rb_write].len = p->len * 2 + 12; + (*txi)[rb_write].flags = RB_USER; + + rb_write++; + if (rb_write == rb_size.num_tx_frames) + rb_write = 0; + + cnt = write(fp, NULL, 0); +// if (cnt < 0) +// printf("Error returned from write: %d\n", cnt); +// sleep(1); + } +} + + +int main(int argc, char *argv[]) +{ + pthread_t tx, rx; + long int t; + struct sched_param s = { + .sched_priority = 1 + }; + int ret, map_size, page_size; + void *rb; + + if (argc < 2) { + printf("%s data_size\n", argv[0]); + return -1; + } + + packet_data_length = atoi(argv[1]); + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + + page_size = getpagesize(); + + ret = ioctl(fp, USRP_E_GET_RB_INFO, &rb_size); + + map_size = (rb_size.num_pages_rx_flags + rb_size.num_pages_tx_flags) * page_size + + (rb_size.num_rx_frames + rb_size.num_tx_frames) * (page_size >> 1); + + rb = mmap(0, map_size, PROT_READ|PROT_WRITE, MAP_SHARED, fp, 0); + if (rb == MAP_FAILED) { + perror("mmap failed"); + return -1; + } + + printf("rb = %X\n", rb); + + rxi = rb; + rx_buf = rb + (rb_size.num_pages_rx_flags * page_size); + txi = rb + (rb_size.num_pages_rx_flags * page_size) + + (rb_size.num_rx_frames * page_size >> 1); + tx_buf = rb + (rb_size.num_pages_rx_flags * page_size) + + (rb_size.num_rx_frames * page_size >> 1) + + (rb_size.num_pages_tx_flags * page_size); + + printf("rxi = %X, rx_buf = %X, txi = %X, tx_buf = %X\n", rxi, rx_buf, txi, tx_buf); + + sched_setscheduler(0, SCHED_RR, &s); + error = 0; + +#if 1 + if (pthread_create(&rx, NULL, read_thread, (void *) t)) { + printf("Failed to create rx thread\n"); + exit(-1); + } + + sleep(1); +#endif + + if (pthread_create(&tx, NULL, write_thread, (void *) t)) { + printf("Failed to create tx thread\n"); + exit(-1); + } + +// while (!error) + sleep(1000000000); + + printf("Done sleeping\n"); +} diff --git a/host/apps/omap_debug/usrp-e-ram.c b/host/apps/omap_debug/usrp-e-ram.c new file mode 100644 index 000000000..d548f7ccd --- /dev/null +++ b/host/apps/omap_debug/usrp-e-ram.c @@ -0,0 +1,25 @@ +#include <stdio.h> +#include <sys/types.h> +#include <fcntl.h> + +int main(int rgc, char *argv[]) +{ + int fp, i, cnt; + unsigned short buf[1024]; + unsigned short buf_rb[1024]; + + fp = open("/dev/usrp1_e0", O_RDWR); + printf("fp = %d\n", fp); + + for (i=0; i<1024; i++) + buf[i] = i*256; + write(fp, buf, 2048); + read(fp, buf_rb, 2048); + + printf("Read back %hX %hX\n", buf_rb[0], buf_rb[1]); + + for (i=0; i<1024; i++) { + if (buf[i] != buf_rb[i]) + printf("Read - %hX, expected - %hX\n", buf_rb[i], buf[i]); + } +} diff --git a/host/apps/omap_debug/usrp-e-random-loopback.c b/host/apps/omap_debug/usrp-e-random-loopback.c new file mode 100644 index 000000000..5960b8fbd --- /dev/null +++ b/host/apps/omap_debug/usrp-e-random-loopback.c @@ -0,0 +1,149 @@ +#include <stdio.h> +#include <sys/types.h> +#include <fcntl.h> +#include <pthread.h> +#include <stdlib.h> +#include <unistd.h> +#include <stddef.h> +#include "usrp_e.h" + +// max length #define PKT_DATA_LENGTH 1014 +static int packet_data_length; + +struct pkt { + int checksum; + int seq_num; + int len; + short data[]; +}; + +static int fp; + +static int calc_checksum(struct pkt *p) +{ + int i, sum; + + i = 0; + sum = 0; + + for (i=0; i < p->len; i++) + sum += p->data[i]; + + sum += p->seq_num; + + return sum; +} + +int randN(int n) +{ + long tmp; + + tmp = rand() % n; + + return tmp; +} + +static void *read_thread(void *threadid) +{ + int cnt, prev_seq_num; + struct usrp_transfer_frame *rx_data; + struct pkt *p; + + printf("Greetings from the reading thread!\n"); + + // IMPORTANT: must assume max length packet from fpga + rx_data = malloc(sizeof(struct usrp_transfer_frame) + sizeof(struct pkt) + (1014 * 2)); + rx_data = malloc(2048); + p = (struct pkt *) ((void *)rx_data + offsetof(struct usrp_transfer_frame, buf)); + //p = &(rx_data->buf[0]); + printf("Address of rx_data = %p, p = %p\n", rx_data, p); + printf("offsetof = %d\n", offsetof(struct usrp_transfer_frame, buf)); + printf("sizeof rx data = %d\n", sizeof(struct usrp_transfer_frame) + sizeof(struct pkt)); + + prev_seq_num = 0; + + while (1) { + + cnt = read(fp, rx_data, 2048); +// printf("Packet received, status = %X, len = %d\n", rx_data->status, rx_data->len); +// printf("p->seq_num = %d\n", p->seq_num); + + if (p->seq_num != prev_seq_num + 1) + printf("Sequence number fail, current = %d, previous = %d\n", + p->seq_num, prev_seq_num); + prev_seq_num = p->seq_num; + + if (calc_checksum(p) != p->checksum) + printf("Checksum fail packet = %d, expected = %d\n", + calc_checksum(p), p->checksum); + printf("."); + fflush(stdout); +// printf("\n"); + } + +} + +static void *write_thread(void *threadid) +{ + int seq_number, i, cnt, pkt_cnt; + struct usrp_transfer_frame *tx_data; + struct pkt *p; + + printf("Greetings from the write thread!\n"); + + // Allocate max length buffer for frame + tx_data = malloc(2048); + p = (struct pkt *) ((void *)tx_data + offsetof(struct usrp_transfer_frame, buf)); + printf("Address of tx_data = %p, p = %p\n", tx_data, p); + + printf("sizeof rp_transfer_frame = %d, sizeof pkt = %d\n", sizeof(struct usrp_transfer_frame), sizeof(struct pkt)); + + for (i=0; i < 1014; i++) +// p->data[i] = random() >> 16; + p->data[i] = i; + + tx_data->status = 0xdeadbeef; + tx_data->len = 8 + packet_data_length * 2; + + printf("tx_data->len = %d\n", tx_data->len); + + seq_number = 1; + + while (1) { + pkt_cnt = randN(16); + for (i = 0; i < pkt_cnt; i++) { + p->seq_num = seq_number++; + p->len = randN(1013) + 1; + p->checksum = calc_checksum(p); + tx_data->len = 12 + p->len * 2; + cnt = write(fp, tx_data, tx_data->len + 8); + } + sleep(random() >> 31); + } +} + + +int main(int argc, char *argv[]) +{ + pthread_t tx, rx; + long int t; + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + + if (pthread_create(&rx, NULL, read_thread, (void *) t)) { + printf("Failed to create rx thread\n"); + exit(-1); + } + + sleep(1); + + if (pthread_create(&tx, NULL, write_thread, (void *) t)) { + printf("Failed to create tx thread\n"); + exit(-1); + } + + sleep(1000000000); + + printf("Done sleeping\n"); +} diff --git a/host/apps/omap_debug/usrp-e-read.c b/host/apps/omap_debug/usrp-e-read.c new file mode 100644 index 000000000..c28f018d5 --- /dev/null +++ b/host/apps/omap_debug/usrp-e-read.c @@ -0,0 +1,18 @@ +#include <stdio.h> +#include <sys/types.h> +#include <fcntl.h> + +int main(int rgc, char *argv[]) +{ + int fp, cnt; + short buf[1024]; + + fp = open("/dev/usrp1_e0", O_RDONLY); + printf("fp = %d\n", fp); + + do { + cnt = read(fp, buf, 2048); +// printf("Bytes read - %d\n", cnt); + } while(1); + printf("Data - %hX\n", buf[0]); +} diff --git a/host/apps/omap_debug/usrp-e-spi.c b/host/apps/omap_debug/usrp-e-spi.c new file mode 100644 index 000000000..c353c409b --- /dev/null +++ b/host/apps/omap_debug/usrp-e-spi.c @@ -0,0 +1,54 @@ +#include <stdio.h> +#include <stdlib.h> +#include <unistd.h> +#include <sys/types.h> +#include <fcntl.h> +#include <sys/ioctl.h> + +#include "usrp_e.h" + +// Usage: usrp_e_spi w|rb slave data + +int main(int argc, char *argv[]) +{ + int fp, slave, length, ret; + unsigned int data; + struct usrp_e_spi spi_dat; + + if (argc < 5) { + printf("Usage: usrp_e_spi w|rb slave transfer_length data\n"); + exit(-1); + } + + slave = atoi(argv[2]); + length = atoi(argv[3]); + data = atoll(argv[4]); + + printf("Data = %X\n", data); + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + if (fp < 0) { + perror("Open failed"); + return -1; + } + +// sleep(1); + + + spi_dat.slave = slave; + spi_dat.data = data; + spi_dat.length = length; + spi_dat.flags = UE_SPI_PUSH_FALL | UE_SPI_LATCH_RISE; + + if (*argv[1] == 'r') { + spi_dat.readback = 1; + ret = ioctl(fp, USRP_E_SPI, &spi_dat); + printf("Ioctl returns: %d, Data returned = %d\n", ret, spi_dat.data); + } else { + spi_dat.readback = 0; + ioctl(fp, USRP_E_SPI, &spi_dat); + } + + return 0; +} diff --git a/host/apps/omap_debug/usrp-e-timed.c b/host/apps/omap_debug/usrp-e-timed.c new file mode 100644 index 000000000..3cb33ce2d --- /dev/null +++ b/host/apps/omap_debug/usrp-e-timed.c @@ -0,0 +1,233 @@ +#include <stdio.h> +#include <sys/types.h> +#include <fcntl.h> +#include <pthread.h> +#include <stdlib.h> +#include <unistd.h> +#include <stddef.h> +#include "usrp_e.h" + +// max length #define PKT_DATA_LENGTH 1016 +static int packet_data_length; + +struct pkt { + int checksum; + int seq_num; + short data[]; +}; + +static int fp; + +static int calc_checksum(struct pkt *p) +{ + int i, sum; + + i = 0; + sum = 0; + + for (i=0; i < packet_data_length; i++) + sum += p->data[i]; + + sum += p->seq_num; + + return sum; +} + +static void *read_thread(void *threadid) +{ + int cnt, prev_seq_num; + struct usrp_transfer_frame *rx_data; + struct pkt *p; + int rx_pkt_cnt; + int i; + unsigned long bytes_transfered, elapsed_seconds; + struct timeval start_time, finish_time; + + printf("Greetings from the reading thread!\n"); + + bytes_transfered = 0; + gettimeofday(&start_time, NULL); + + // IMPORTANT: must assume max length packet from fpga + rx_data = malloc(sizeof(struct usrp_transfer_frame) + sizeof(struct pkt) + (1016 * 2)); + p = (struct pkt *) ((void *)rx_data + offsetof(struct usrp_transfer_frame, buf)); + //p = &(rx_data->buf[0]); + printf("Address of rx_data = %p, p = %p\n", rx_data, p); + printf("offsetof = %d\n", offsetof(struct usrp_transfer_frame, buf)); + printf("sizeof rx data = %d\n", sizeof(struct usrp_transfer_frame) + sizeof(struct pkt)); + + prev_seq_num = 0; + + rx_pkt_cnt = 0; + + while (1) { + + cnt = read(fp, rx_data, 2048); + if (cnt < 0) + printf("Error returned from read: %d\n", cnt); + rx_pkt_cnt++; + +#if 0 + if (rx_pkt_cnt == 512) { + printf("."); + fflush(stdout); + rx_pkt_cnt = 0; + } +#endif + + if (rx_data->status & RB_OVERRUN) + printf("O"); + + bytes_transfered += rx_data->len; + + if (bytes_transfered > (100 * 1000000)) { + gettimeofday(&finish_time, NULL); + elapsed_seconds = finish_time.tv_sec - start_time.tv_sec; + + printf("RX data transfer rate = %f K Samples/second\n", + (float) bytes_transfered / (float) elapsed_seconds / 4000); + + + start_time = finish_time; + bytes_transfered = 0; + } + } + +} + +static void *write_thread(void *threadid) +{ + int seq_number, i, cnt, tx_pkt_cnt; + struct usrp_transfer_frame *tx_data; + struct pkt *p; + unsigned long bytes_transfered, elapsed_seconds; + struct timeval start_time, finish_time; + + printf("Greetings from the write thread!\n"); + + bytes_transfered = 0; + gettimeofday(&start_time, NULL); + + tx_data = malloc(sizeof(struct usrp_transfer_frame) + sizeof(struct pkt) + (packet_data_length * 2)); + p = (struct pkt *) ((void *)tx_data + offsetof(struct usrp_transfer_frame, buf)); + printf("Address of tx_data = %p, p = %p\n", tx_data, p); + + printf("sizeof rp_transfer_frame = %d, sizeof pkt = %d\n", sizeof(struct usrp_transfer_frame), sizeof(struct pkt)); + + for (i=0; i < packet_data_length; i++) +// p->data[i] = random() >> 16; + p->data[i] = i; + + tx_data->status = 0; + tx_data->len = 8 + packet_data_length * 2; + + printf("tx_data->len = %d\n", tx_data->len); + + seq_number = 1; + tx_pkt_cnt = 0; + + while (1) { + + tx_pkt_cnt++; + +#if 0 + if (tx_pkt_cnt == 512) { + printf("."); + fflush(stdout); + } + if (tx_pkt_cnt == 1024) { + printf("'"); + fflush(stdout); + } + if (tx_pkt_cnt == 1536) { + printf(":"); + fflush(stdout); + tx_pkt_cnt = 0; + } +#endif + +// printf("tx status = %X, len = %d\n", tx_data->status, tx_data->len); + p->seq_num = seq_number++; + p->checksum = calc_checksum(p); + cnt = write(fp, tx_data, 2048); + if (cnt < 0) + printf("Error returned from write: %d\n", cnt); + + bytes_transfered += tx_data->len; + + if (bytes_transfered > (100 * 1000000)) { + gettimeofday(&finish_time, NULL); + elapsed_seconds = finish_time.tv_sec - start_time.tv_sec; + + printf("TX data transfer rate = %f K Samples/second\n", + (float) bytes_transfered / (float) elapsed_seconds / 4000); + + + start_time = finish_time; + bytes_transfered = 0; + } +// sleep(1); + } +} + + +int main(int argc, char *argv[]) +{ + pthread_t tx, rx; + long int t; + int fpga_config_flag ,decimation; + struct usrp_e_ctl16 d; + struct sched_param s = { + .sched_priority = 1 + }; + + if (argc < 4) { + printf("%s r|w|rw decimation data_size\n", argv[0]); + return -1; + } + + decimation = atoi(argv[2]); + packet_data_length = atoi(argv[3]); + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + + fpga_config_flag = 0; + if (strcmp(argv[1], "w") == 0) + fpga_config_flag |= (1 << 15); + else if (strcmp(argv[1], "r") == 0) + fpga_config_flag |= (1 << 14); + else if (strcmp(argv[1], "rw") == 0) + fpga_config_flag |= ((1 << 15) | (1 << 14)); + + fpga_config_flag |= decimation; + + d.offset = 14; + d.count = 1; + d.buf[0] = fpga_config_flag; + ioctl(fp, USRP_E_WRITE_CTL16, &d); + + sleep(1); // in case the kernel threads need time to start. FIXME if so + + sched_setscheduler(0, SCHED_RR, &s); + + if (fpga_config_flag & (1 << 14)) { + if (pthread_create(&rx, NULL, read_thread, (void *) t)) { + printf("Failed to create rx thread\n"); + exit(-1); + } + } + + sleep(1); + + if (fpga_config_flag & (1 << 15)) { + if (pthread_create(&tx, NULL, write_thread, (void *) t)) { + printf("Failed to create tx thread\n"); + exit(-1); + } + } + + sleep(10000); + + printf("Done sleeping\n"); +} diff --git a/host/apps/omap_debug/usrp-e-uart-rx.c b/host/apps/omap_debug/usrp-e-uart-rx.c new file mode 100644 index 000000000..24b417980 --- /dev/null +++ b/host/apps/omap_debug/usrp-e-uart-rx.c @@ -0,0 +1,53 @@ +#include <stdio.h> +#include <stdlib.h> +#include <sys/types.h> +#include <fcntl.h> +#include <string.h> +#include <sys/ioctl.h> + +#include "usrp_e.h" +#include "usrp_e_regs.hpp" + +// Usage: usrp_e_uart <string> + + +int main(int argc, char *argv[]) +{ + int fp, ret; + struct usrp_e_ctl16 d; + __u16 clkdiv; + + if (argc == 0) { + printf("Usage: usrp-e-uart-rx <opt clkdiv>\n"); + printf("clkdiv = 278 is 230.4k \n"); + printf("clkdiv = 556 is 115.2k \n"); + exit(-1); + } + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + + if (argc == 2) { + clkdiv = atoi(argv[1]); + d.offset = UE_REG_UART_CLKDIV; + d.count = 1; + d.buf[0] = clkdiv; + ret = ioctl(fp, USRP_E_WRITE_CTL16, &d); + } + + while(1) { + d.offset = UE_REG_UART_RXLEVEL; + d.count = 1; + ret = ioctl(fp, USRP_E_READ_CTL16, &d); + + if (d.buf[0] > 0) { + d.offset = UE_REG_UART_RXCHAR; + d.count = 1; + ret = ioctl(fp, USRP_E_READ_CTL16, &d); + printf("%c", d.buf[0]); + fflush(stdout); + } + } + + return 0; +} diff --git a/host/apps/omap_debug/usrp-e-uart.c b/host/apps/omap_debug/usrp-e-uart.c new file mode 100644 index 000000000..2956c407f --- /dev/null +++ b/host/apps/omap_debug/usrp-e-uart.c @@ -0,0 +1,48 @@ +#include <stdio.h> +#include <stdlib.h> +#include <sys/types.h> +#include <fcntl.h> +#include <string.h> +#include <sys/ioctl.h> + +#include "usrp_e.h" +#include "usrp_e_regs.hpp" + +// Usage: usrp_e_uart <string> + + +int main(int argc, char *argv[]) +{ + int fp, i, ret; + struct usrp_e_ctl16 d; + char *str = argv[1]; + __u16 clkdiv; + + if (argc < 2) { + printf("Usage: usrp_e_uart <string> <opt clkdiv>\n"); + printf("clkdiv = 278 is 230.4k \n"); + printf("clkdiv = 556 is 115.2k \n"); + exit(-1); + } + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + + if (argc == 3) { + clkdiv = atoi(argv[2]); + d.offset = UE_REG_UART_CLKDIV; + d.count = 1; + d.buf[0] = clkdiv; + ret = ioctl(fp, USRP_E_WRITE_CTL16, &d); + } + + for (i=0; i<strlen(str); i++) { + d.offset = UE_REG_UART_TXCHAR; + d.count = 1; + d.buf[0] = str[i]; + ret = ioctl(fp, USRP_E_WRITE_CTL16, &d); + printf("Wrote %X, to %X, ret = %d\n", d.buf[0], d.offset, ret); + } + + return 0; +} diff --git a/host/apps/omap_debug/usrp-e-write.c b/host/apps/omap_debug/usrp-e-write.c new file mode 100644 index 000000000..903c0071f --- /dev/null +++ b/host/apps/omap_debug/usrp-e-write.c @@ -0,0 +1,21 @@ +#include <stdio.h> +#include <sys/types.h> +#include <fcntl.h> + +int main(int rgc, char *argv[]) +{ + int fp, i, cnt; + short buf[1024]; + + fp = open("/dev/usrp1_e0", O_WRONLY); + printf("fp = %d\n", fp); + + for (i=0; i<1024; i++) { + buf[i] = i; + } + +// do { + cnt = write(fp, buf, 2048); + printf("Bytes written - %d\n", cnt); +// } while (1); +} diff --git a/host/apps/omap_debug/usrp_e.h b/host/apps/omap_debug/usrp_e.h new file mode 100644 index 000000000..f96706c4a --- /dev/null +++ b/host/apps/omap_debug/usrp_e.h @@ -0,0 +1,90 @@ + +/* + * Copyright (C) 2010 Ettus Research, LLC + * + * Written by Philip Balister <philip@opensdr.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __USRP_E_H +#define __USRP_E_H + +#include <linux/types.h> +#include <linux/ioctl.h> + +struct usrp_e_ctl16 { + __u32 offset; + __u32 count; + __u16 buf[20]; +}; + +struct usrp_e_ctl32 { + __u32 offset; + __u32 count; + __u32 buf[10]; +}; + +/* SPI interface */ + +#define UE_SPI_TXONLY 0 +#define UE_SPI_TXRX 1 + +/* Defines for spi ctrl register */ +#define UE_SPI_CTRL_TXNEG (BIT(10)) +#define UE_SPI_CTRL_RXNEG (BIT(9)) + +#define UE_SPI_PUSH_RISE 0 +#define UE_SPI_PUSH_FALL UE_SPI_CTRL_TXNEG +#define UE_SPI_LATCH_RISE 0 +#define UE_SPI_LATCH_FALL UE_SPI_CTRL_RXNEG +#define USRP_E_GET_COMPAT_NUMBER _IO(USRP_E_IOC_MAGIC, 0x28) + +#define USRP_E_COMPAT_NUMBER 1 + +struct usrp_e_spi { + __u8 readback; + __u32 slave; + __u32 data; + __u32 length; + __u32 flags; +}; + +struct usrp_e_i2c { + __u8 addr; + __u32 len; + __u8 data[]; +}; + +#define USRP_E_IOC_MAGIC 'u' +#define USRP_E_WRITE_CTL16 _IOW(USRP_E_IOC_MAGIC, 0x20, struct usrp_e_ctl16) +#define USRP_E_READ_CTL16 _IOWR(USRP_E_IOC_MAGIC, 0x21, struct usrp_e_ctl16) +#define USRP_E_WRITE_CTL32 _IOW(USRP_E_IOC_MAGIC, 0x22, struct usrp_e_ctl32) +#define USRP_E_READ_CTL32 _IOWR(USRP_E_IOC_MAGIC, 0x23, struct usrp_e_ctl32) +#define USRP_E_SPI _IOWR(USRP_E_IOC_MAGIC, 0x24, struct usrp_e_spi) +#define USRP_E_I2C_READ _IOWR(USRP_E_IOC_MAGIC, 0x25, struct usrp_e_i2c) +#define USRP_E_I2C_WRITE _IOW(USRP_E_IOC_MAGIC, 0x26, struct usrp_e_i2c) +#define USRP_E_GET_RB_INFO _IOR(USRP_E_IOC_MAGIC, 0x27, struct usrp_e_ring_buffer_size_t) + +/* Flag defines */ +#define RB_USER (1<<0) +#define RB_KERNEL (1<<1) +#define RB_OVERRUN (1<<2) +#define RB_DMA_ACTIVE (1<<3) + +struct ring_buffer_info { + int flags; + int len; +}; + +struct usrp_e_ring_buffer_size_t { + int num_pages_rx_flags; + int num_rx_frames; + int num_pages_tx_flags; + int num_tx_frames; +}; + +#endif diff --git a/host/apps/omap_debug/write-eeprom.sh b/host/apps/omap_debug/write-eeprom.sh new file mode 100755 index 000000000..301b06f07 --- /dev/null +++ b/host/apps/omap_debug/write-eeprom.sh @@ -0,0 +1,92 @@ +#!/bin/bash + +if [ $# -ne 3 ] && [ $# -ne 5 ]; +then + echo "Usage:" + echo "" + echo "writeprom.sh deviceid rev fab_rev [envvar envsetting]" + echo + echo " deviceid - expansion board device number from table:" + echo + echo " Summit 0x01" + echo " Tobi 0x02" + echo " Tobi Duo 0x03" + echo " Palo35 0x04" + echo " Palo43 0x05" + echo " Chestnut43 0x06" + echo " Pinto 0x07" + echo + echo " rev - board revision (e.g. 0x00)" + echo " fab_rev - revision marking from pcb (e.g. R2411)" + echo " envvar - optional u-boot env variable name" + echo " (e.g. dvimode)" + echo " envsetting - optional u-boot env variable setting" + echo " (e.g. 1024x768MR-16@60)" + exit 1 +fi + +fabrevision=$3 +if [ ${#fabrevision} -ge 8 ]; then + echo "Error: fab revision string must less than 8 characters" + exit 1 +fi + +envvar=$4 +if [ ${#envar} -ge 16 ]; then + echo "Error: environment variable name string must less than 16 characters" + exit 1 +fi + +envsetting=$5 +if [ ${#ensetting} -ge 64 ]; then + echo "Error: environment setting string must less than 64 characters" + exit 1 +fi + +bus=3 +device=0x51 +vendorid=0x03 + +i2cset -y $bus $device 0x00 0x00 +i2cset -y $bus $device 0x01 $vendorid +i2cset -y $bus $device 0x02 0x00 +i2cset -y $bus $device 0x03 $1 +i2cset -y $bus $device 0x04 $2 +i2cset -y $bus $device 0x05 00 + +let i=6 +hexdumpargs="'${#fabrevision}/1 \"0x%02x \"'" +command="echo -n \"$fabrevision\" | hexdump -e $hexdumpargs" +hex=$(eval $command) +for character in $hex; do + i2cset -y $bus $device $i $character + let i=$i+1 +done +i2cset -y $bus $device $i 0x00 + +if [ $# -eq 5 ] +then + i2cset -y $bus $device 0x05 0x01 + + let i=14 + hexdumpargs="'${#envvar}/1 \"0x%02x \"'" + command="echo -n \"$envvar\" | hexdump -e $hexdumpargs" + hex=$(eval $command) + for character in $hex; do + i2cset -y $bus $device $i $character + let i=$i+1 + done + i2cset -y $bus $device $i 0x00 + + let i=30 + hexdumpargs="'${#envsetting}/1 \"0x%02x \"'" + command="echo -n \"$envsetting\" | hexdump -e $hexdumpargs" + hex=$(eval $command) + for character in $hex; do + i2cset -y $bus $device $i $character + let i=$i+1 + done + i2cset -y $bus $device $i 0x00 +fi + + diff --git a/host/apps/omap_debug/write_board_id.sh b/host/apps/omap_debug/write_board_id.sh new file mode 100755 index 000000000..067269c64 --- /dev/null +++ b/host/apps/omap_debug/write_board_id.sh @@ -0,0 +1,10 @@ +#!/bin/sh + +i2cset -y 3 0x51 0x00 0x00 +i2cset -y 3 0x51 0x01 0x03 +i2cset -y 3 0x51 0x02 0x00 +i2cset -y 3 0x51 0x03 0x01 +i2cset -y 3 0x51 0x04 0x00 +i2cset -y 3 0x51 0x05 0x00 + + diff --git a/host/examples/ascii_art_dft.hpp b/host/examples/ascii_art_dft.hpp index 92fb77596..ee2267c2d 100644 --- a/host/examples/ascii_art_dft.hpp +++ b/host/examples/ascii_art_dft.hpp @@ -28,7 +28,7 @@ namespace acsii_art_dft{ ); /*! - * Convert a DFT to a printable ascii plot. + * Convert a DFT to a piroundable ascii plot. * \param dft the log power dft bins * \param width the frame width in characters * \param height the frame height in characters diff --git a/host/examples/tx_from_file.cpp b/host/examples/tx_from_file.cpp new file mode 100644 index 000000000..9611cf47c --- /dev/null +++ b/host/examples/tx_from_file.cpp @@ -0,0 +1,125 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include <uhd/utils/thread_priority.hpp> +#include <uhd/utils/safe_main.hpp> +#include <uhd/usrp/simple_usrp.hpp> +#include <boost/program_options.hpp> +#include <boost/format.hpp> +#include <iostream> +#include <complex> +#include <fstream> + +namespace po = boost::program_options; + +int UHD_SAFE_MAIN(int argc, char *argv[]){ + uhd::set_thread_priority_safe(); + + //variables to be set by po + std::string args; + time_t seconds_in_future; + size_t total_num_samps; + size_t samps_per_packet; + double tx_rate, freq; + float ampl; + float tx_gain; + + //setup the program options + po::options_description desc("Allowed options"); + desc.add_options() + ("help", "help message") + ("args", po::value<std::string>(&args)->default_value(""), "simple uhd device address args") + ("secs", po::value<time_t>(&seconds_in_future)->default_value(3), "number of seconds in the future to transmit") + ("nsamps", po::value<size_t>(&total_num_samps)->default_value(1000), "total number of samples to transmit") + ("txrate", po::value<double>(&tx_rate)->default_value(100e6/16), "rate of outgoing samples") + ("freq", po::value<double>(&freq)->default_value(0), "rf center frequency in Hz") + ("ampl", po::value<float>(&l)->default_value(float(0.3)), "amplitude of each sample") + ("gain", po::value<float>(&tx_gain)->default_value(float(0)), "amplitude of each sample") + ("dilv", "specify to disable inner-loop verbose") + ; + po::variables_map vm; + po::store(po::parse_command_line(argc, argv, desc), vm); + po::notify(vm); + + //print the help message + if (vm.count("help")){ + std::cout << boost::format("UHD TX Timed Samples %s") % desc << std::endl; + return ~0; + } + + bool verbose = vm.count("dilv") == 0; + + //create a usrp device + std::cout << std::endl; + std::cout << boost::format("Creating the usrp device with: %s...") % args << std::endl; + uhd::usrp::simple_usrp::sptr sdev = uhd::usrp::simple_usrp::make(args); + uhd::device::sptr dev = sdev->get_device(); + std::cout << boost::format("Using Device: %s") % sdev->get_pp_string() << std::endl; + + //set properties on the device + std::cout << boost::format("Setting TX Rate: %f Msps...") % (tx_rate/1e6) << std::endl; + sdev->set_tx_rate(tx_rate); + std::cout << boost::format("Actual TX Rate: %f Msps...") % (sdev->get_tx_rate()/1e6) << std::endl; + std::cout << boost::format("Setting device timestamp to 0...") << std::endl; + sdev->set_tx_freq(freq); + sdev->set_time_now(uhd::time_spec_t(0.0)); + + sdev->set_tx_gain(tx_gain); + + //allocate data to send + std::vector<std::complex<short> > buff; + uhd::tx_metadata_t md; + + std::cout << "Read data to send from file: in.dat" << std::endl; + std::ifstream infile("in.dat", std::ifstream::binary); + while (!infile.eof()) { + std::complex<short> c; + infile.read((char *)&c, sizeof(std::complex<short>)); + if (!((c.real() == 0) && (c.imag() == 0))) { + buff.push_back(c); +//std::cout << "C = " << c << std::endl; + } + } + samps_per_packet = buff.size(); + infile.close(); + std::cout << "Number of samples in file: " << samps_per_packet << std::endl; + + //send the data in multiple packets + size_t num_packets = (total_num_samps+samps_per_packet-1)/samps_per_packet; + for (size_t i = 0; i < num_packets; i++){ + //setup the metadata flags and time spec + md.start_of_burst = true; //always SOB (good for continuous streaming) + md.end_of_burst = (i == num_packets-1); //only last packet has EOB + md.has_time_spec = (i == 0); //only first packet has time + md.time_spec = uhd::time_spec_t(seconds_in_future); + + size_t samps_to_send = std::min(total_num_samps - samps_per_packet*i, samps_per_packet); + + //send the entire packet (driver fragments internally) + size_t num_tx_samps = dev->send( + &buff.front(), samps_to_send, md, + uhd::io_type_t::COMPLEX_INT16, + uhd::device::SEND_MODE_FULL_BUFF + ); + if(verbose) std::cout << std::endl << boost::format("Sent %d samples") % num_tx_samps << std::endl; + } + + //finished + std::cout << std::endl << "Done!" << std::endl << std::endl; + + return 0; +} diff --git a/host/include/uhd/usrp/mboard_eeprom.hpp b/host/include/uhd/usrp/mboard_eeprom.hpp index 530b177be..52363b95c 100644 --- a/host/include/uhd/usrp/mboard_eeprom.hpp +++ b/host/include/uhd/usrp/mboard_eeprom.hpp @@ -37,7 +37,8 @@ namespace uhd{ namespace usrp{ //! Possible EEPROM maps types enum map_type{ MAP_N100, - MAP_B000 + MAP_B000, + MAP_E100 }; //! Make a new empty mboard eeprom diff --git a/host/include/uhd/utils/pimpl.hpp b/host/include/uhd/utils/pimpl.hpp index 18454f0c4..09bf0c0a2 100644 --- a/host/include/uhd/utils/pimpl.hpp +++ b/host/include/uhd/utils/pimpl.hpp @@ -20,7 +20,6 @@ #include <uhd/config.hpp> #include <boost/shared_ptr.hpp> -#include <boost/make_shared.hpp> /*! \file pimpl.hpp * "Pimpl idiom" (pointer to implementation idiom). @@ -51,6 +50,6 @@ * \param _args the constructor args for the pimpl */ #define UHD_PIMPL_MAKE(_name, _args) \ - boost::make_shared<_name> _args + boost::shared_ptr<_name>(new _name _args) #endif /* INCLUDED_UHD_UTILS_PIMPL_HPP */ diff --git a/host/lib/ic_reg_maps/gen_ad9522_regs.py b/host/lib/ic_reg_maps/gen_ad9522_regs.py index ed6b5f48d..a5debe568 100755 --- a/host/lib/ic_reg_maps/gen_ad9522_regs.py +++ b/host/lib/ic_reg_maps/gen_ad9522_regs.py @@ -134,8 +134,8 @@ reg2eeprom 0xB03[0] 0 # Template for methods in the body of the struct ######################################################################## BODY_TMPL="""\ -boost::uint8_t get_reg(boost::uint16_t addr){ - boost::uint8_t reg = 0; +boost::uint32_t get_reg(boost::uint16_t addr){ + boost::uint32_t reg = 0; switch(addr){ #for $addr in sorted(set(map(lambda r: r.get_addr(), $regs))) case $addr: @@ -154,7 +154,7 @@ boost::uint8_t get_reg(boost::uint16_t addr){ return reg; } -void set_reg(boost::uint8_t addr, boost::uint32_t reg){ +void set_reg(boost::uint16_t addr, boost::uint32_t reg){ switch(addr){ #for $addr in sorted(set(map(lambda r: r.get_addr(), $regs))) case $addr: diff --git a/host/lib/transport/CMakeLists.txt b/host/lib/transport/CMakeLists.txt index b9ec7a6ad..b95d46381 100644 --- a/host/lib/transport/CMakeLists.txt +++ b/host/lib/transport/CMakeLists.txt @@ -58,6 +58,12 @@ IF(HAVE_EMMINTRIN_H) ADD_DEFINITIONS(-DHAVE_EMMINTRIN_H) ENDIF(HAVE_EMMINTRIN_H) +INCLUDE(CheckIncludeFileCXX) +CHECK_INCLUDE_FILE_CXX(arm_neon.h HAVE_ARM_NEON_H) + +IF(HAVE_ARM_NEON_H) + ADD_DEFINITIONS(-DHAVE_ARM_NEON_H) +ENDIF(HAVE_ARM_NEON_H) ######################################################################## # Setup defines for interface address discovery ######################################################################## diff --git a/host/lib/transport/convert_types_impl.hpp b/host/lib/transport/convert_types_impl.hpp index 90618dec6..48ff99725 100644 --- a/host/lib/transport/convert_types_impl.hpp +++ b/host/lib/transport/convert_types_impl.hpp @@ -32,6 +32,14 @@ #include <emmintrin.h> #endif +#ifdef HAVE_ARM_NEON_H + #define USE_ARM_NEON_H +#endif + +#if defined(USE_ARM_NEON_H) + #include <arm_neon.h> +#endif + /*********************************************************************** * Typedefs **********************************************************************/ @@ -135,6 +143,26 @@ static UHD_INLINE void fc32_to_item32_nswap( } } +#elif defined(USE_ARM_NEON_H) +static UHD_INLINE void fc32_to_item32_nswap( + const fc32_t *input, item32_t *output, size_t nsamps) +{ + size_t i; + + float32x4_t Q0 = vdupq_n_f32(shorts_per_float); + for (i=0; i < (nsamps & ~0x03); i+=2) { + float32x4_t Q1 = vld1q_f32(reinterpret_cast<const float *>(&input[i])); + float32x4_t Q2 = vmulq_f32(Q1, Q0); + int32x4_t Q3 = vcvtq_s32_f32(Q2); + int16x4_t D8 = vmovn_s32(Q3); + int16x4_t D9 = vrev32_s16(D8); + vst1_s16((reinterpret_cast<int16_t *>(&output[i])), D9); + } + + for (; i < nsamps; i++) + output[i] = fc32_to_item32(input[i]); +} + #else static UHD_INLINE void fc32_to_item32_nswap( const fc32_t *input, item32_t *output, size_t nsamps @@ -238,6 +266,26 @@ static UHD_INLINE void item32_to_fc32_nswap( } } +#elif defined(USE_ARM_NEON_H) +static UHD_INLINE void item32_to_fc32_nswap( + const item32_t *input, fc32_t *output, size_t nsamps) +{ + size_t i; + + float32x4_t Q1 = vdupq_n_f32(floats_per_short); + for (i=0; i < (nsamps & ~0x03); i+=2) { + int16x4_t D0 = vld1_s16(reinterpret_cast<const int16_t *>(&input[i])); + int16x4_t D1 = vrev32_s16(D0); + int32x4_t Q2 = vmovl_s16(D1); + float32x4_t Q3 = vcvtq_f32_s32(Q2); + float32x4_t Q4 = vmulq_f32(Q3, Q1); + vst1q_f32((reinterpret_cast<float *>(&output[i])), Q4); + } + + for (; i < nsamps; i++) + output[i] = item32_to_fc32(input[i]); +} + #else static UHD_INLINE void item32_to_fc32_nswap( const item32_t *input, fc32_t *output, size_t nsamps diff --git a/host/lib/usrp/CMakeLists.txt b/host/lib/usrp/CMakeLists.txt index 3d832c356..073b3c80b 100644 --- a/host/lib/usrp/CMakeLists.txt +++ b/host/lib/usrp/CMakeLists.txt @@ -35,3 +35,4 @@ LIBUHD_APPEND_SOURCES( INCLUDE(${CMAKE_SOURCE_DIR}/lib/usrp/dboard/CMakeLists.txt) INCLUDE(${CMAKE_SOURCE_DIR}/lib/usrp/usrp1/CMakeLists.txt) INCLUDE(${CMAKE_SOURCE_DIR}/lib/usrp/usrp2/CMakeLists.txt) +INCLUDE(${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/CMakeLists.txt) diff --git a/host/lib/usrp/mboard_eeprom.cpp b/host/lib/usrp/mboard_eeprom.cpp index e7470944c..a9270cda6 100644 --- a/host/lib/usrp/mboard_eeprom.cpp +++ b/host/lib/usrp/mboard_eeprom.cpp @@ -18,10 +18,12 @@ #include <uhd/usrp/mboard_eeprom.hpp> #include <uhd/types/mac_addr.hpp> #include <uhd/utils/algorithm.hpp> +#include <uhd/utils/byteswap.hpp> #include <boost/asio/ip/address_v4.hpp> #include <boost/assign/list_of.hpp> #include <boost/lexical_cast.hpp> #include <boost/foreach.hpp> +#include <cstddef> using namespace uhd; using namespace uhd::usrp; @@ -171,6 +173,85 @@ static void store_b000(const mboard_eeprom_t &mb_eeprom, i2c_iface &iface){ string_to_bytes(mb_eeprom["name"], NAME_MAX_LEN) ); } +/*********************************************************************** + * Implementation of E100 load/store + **********************************************************************/ +static const boost::uint8_t E100_EEPROM_ADDR = 0x51; + +struct e100_eeprom_map{ + boost::uint16_t vendor; + boost::uint16_t device; + unsigned char revision; + unsigned char content; + unsigned char model[8]; + unsigned char env_var[16]; + unsigned char env_setting[64]; + unsigned char serial[10]; + unsigned char name[NAME_MAX_LEN]; +}; + +template <typename T> static const byte_vector_t to_bytes(const T &item){ + return byte_vector_t( + reinterpret_cast<const byte_vector_t::value_type *>(&item), + reinterpret_cast<const byte_vector_t::value_type *>(&item)+sizeof(item) + ); +} + +static void load_e100(mboard_eeprom_t &mb_eeprom, i2c_iface &iface){ + const size_t num_bytes = offsetof(e100_eeprom_map, model); + byte_vector_t map_bytes = iface.read_eeprom(E100_EEPROM_ADDR, 0, num_bytes); + e100_eeprom_map map; std::memcpy(&map, &map_bytes[0], map_bytes.size()); + + mb_eeprom["vendor"] = boost::lexical_cast<std::string>(uhd::ntohx(map.vendor)); + mb_eeprom["device"] = boost::lexical_cast<std::string>(uhd::ntohx(map.device)); + mb_eeprom["revision"] = boost::lexical_cast<std::string>(unsigned(map.revision)); + mb_eeprom["content"] = boost::lexical_cast<std::string>(unsigned(map.content)); + + #define load_e100_string_xx(key) mb_eeprom[#key] = bytes_to_string(iface.read_eeprom( \ + E100_EEPROM_ADDR, offsetof(e100_eeprom_map, key), sizeof(e100_eeprom_map::key) \ + )); + + load_e100_string_xx(model); + load_e100_string_xx(env_var); + load_e100_string_xx(env_setting); + load_e100_string_xx(serial); + load_e100_string_xx(name); +} + +static void store_e100(const mboard_eeprom_t &mb_eeprom, i2c_iface &iface){ + + if (mb_eeprom.has_key("vendor")) iface.write_eeprom( + E100_EEPROM_ADDR, offsetof(e100_eeprom_map, vendor), + to_bytes(uhd::htonx(boost::lexical_cast<boost::uint16_t>(mb_eeprom["vendor"]))) + ); + + if (mb_eeprom.has_key("device")) iface.write_eeprom( + E100_EEPROM_ADDR, offsetof(e100_eeprom_map, device), + to_bytes(uhd::htonx(boost::lexical_cast<boost::uint16_t>(mb_eeprom["device"]))) + ); + + if (mb_eeprom.has_key("revision")) iface.write_eeprom( + E100_EEPROM_ADDR, offsetof(e100_eeprom_map, revision), + byte_vector_t(1, boost::lexical_cast<unsigned>(mb_eeprom["revision"])) + ); + + if (mb_eeprom.has_key("content")) iface.write_eeprom( + E100_EEPROM_ADDR, offsetof(e100_eeprom_map, content), + byte_vector_t(1, boost::lexical_cast<unsigned>(mb_eeprom["content"])) + ); + + #define store_e100_string_xx(key) if (mb_eeprom.has_key(#key)) iface.write_eeprom( \ + E100_EEPROM_ADDR, offsetof(e100_eeprom_map, key), \ + string_to_bytes(mb_eeprom[#key], sizeof(e100_eeprom_map::key)) \ + ); + + store_e100_string_xx(model); + store_e100_string_xx(env_var); + store_e100_string_xx(env_setting); + store_e100_string_xx(serial); + store_e100_string_xx(name); + +} /*********************************************************************** * Implementation of mboard eeprom @@ -183,6 +264,7 @@ mboard_eeprom_t::mboard_eeprom_t(i2c_iface &iface, map_type map){ switch(map){ case MAP_N100: load_n100(*this, iface); break; case MAP_B000: load_b000(*this, iface); break; + case MAP_E100: load_e100(*this, iface); break; } } @@ -190,5 +272,6 @@ void mboard_eeprom_t::commit(i2c_iface &iface, map_type map){ switch(map){ case MAP_N100: store_n100(*this, iface); break; case MAP_B000: store_b000(*this, iface); break; + case MAP_E100: store_e100(*this, iface); break; } } diff --git a/host/lib/usrp/usrp_e100/CMakeLists.txt b/host/lib/usrp/usrp_e100/CMakeLists.txt new file mode 100644 index 000000000..66c87e0d8 --- /dev/null +++ b/host/lib/usrp/usrp_e100/CMakeLists.txt @@ -0,0 +1,60 @@ +# +# Copyright 2010 Ettus Research LLC +# +# This program is free software: you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation, either version 3 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. +# + +#This file will be included by cmake, use absolute paths! + +######################################################################## +# Conditionally configure the USRP-E100 support +######################################################################## +MESSAGE(STATUS "Configuring USRP-E100 support...") + +IF(DEFINED ENABLE_USRP_E100) + IF(ENABLE_USRP_E100) + MESSAGE(STATUS "USRP-E100 support enabled by configure flag") + ELSE(ENABLE_USRP_E100) + MESSAGE(STATUS "USRP-E100 support disabled by configure flag") + ENDIF(ENABLE_USRP_E100) +ELSE(DEFINED ENABLE_USRP_E100) #not defined: automatic disabling of component + SET(ENABLE_USRP_E100 FALSE) +ENDIF(DEFINED ENABLE_USRP_E100) +SET(ENABLE_USRP_E100 ${ENABLE_USRP_E100} CACHE BOOL "enable USRP-E100 support") + +IF(ENABLE_USRP_E100) + MESSAGE(STATUS " Building USRP-E100 support.") + INCLUDE_DIRECTORIES(${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/include) + LIBUHD_APPEND_SOURCES( + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/clock_ctrl.cpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/clock_ctrl.hpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/codec_ctrl.cpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/codec_ctrl.hpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/codec_impl.cpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/dboard_impl.cpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/dboard_iface.cpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/dsp_impl.cpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/fpga-downloader.cc + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/io_impl.cpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/mboard_impl.cpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/usrp_e100_impl.cpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/usrp_e100_impl.hpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/usrp_e100_iface.cpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/usrp_e100_iface.hpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/usrp_e100_mmap_zero_copy.cpp + ${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/usrp_e100_regs.hpp + ) +ELSE(ENABLE_USRP_E100) + MESSAGE(STATUS " Skipping USRP-E100 support.") +ENDIF(ENABLE_USRP_E100) diff --git a/host/lib/usrp/usrp_e100/clock_ctrl.cpp b/host/lib/usrp/usrp_e100/clock_ctrl.cpp new file mode 100644 index 000000000..1fb1a7125 --- /dev/null +++ b/host/lib/usrp/usrp_e100/clock_ctrl.cpp @@ -0,0 +1,263 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include "clock_ctrl.hpp" +#include "ad9522_regs.hpp" +#include <uhd/utils/assert.hpp> +#include <boost/cstdint.hpp> +#include "usrp_e100_regs.hpp" //spi slave constants +#include <boost/assign/list_of.hpp> +#include <boost/foreach.hpp> +#include <utility> +#include <iostream> + +using namespace uhd; + +template <typename div_type, typename bypass_type> static void set_clock_divider( + size_t divider, div_type &low, div_type &high, bypass_type &bypass +){ + high = divider/2 - 1; + low = divider - high - 2; + bypass = (divider == 1)? 1 : 0; +} + +/*********************************************************************** + * Constants + **********************************************************************/ +static const bool enable_test_clock = false; +static const size_t ref_clock_doubler = 2; //enabled below +static const double ref_clock_rate = 10e6 * ref_clock_doubler; + +static const size_t r_counter = 1; +static const size_t a_counter = 0; +static const size_t b_counter = 20 / ref_clock_doubler; +static const size_t prescaler = 8; //set below with enum, set to 8 when input is under 2400 MHz +static const size_t vco_divider = 5; //set below with enum + +static const size_t n_counter = prescaler * b_counter + a_counter; +static const size_t vco_clock_rate = ref_clock_rate/r_counter * n_counter; //between 1400 and 1800 MHz +static const double master_clock_rate = vco_clock_rate/vco_divider; + +static const size_t fpga_clock_divider = size_t(master_clock_rate/64e6); +static const size_t codec_clock_divider = size_t(master_clock_rate/64e6); + +/*********************************************************************** + * Clock Control Implementation + **********************************************************************/ +class usrp_e100_clock_ctrl_impl : public usrp_e100_clock_ctrl{ +public: + usrp_e100_clock_ctrl_impl(usrp_e100_iface::sptr iface){ + _iface = iface; + + //init the clock gen registers + //Note: out0 should already be clocking the FPGA or this isnt going to work + _ad9522_regs.sdo_active = ad9522_regs_t::SDO_ACTIVE_SDO_SDIO; + _ad9522_regs.enable_clock_doubler = 1; //enable ref clock doubler + _ad9522_regs.enb_stat_eeprom_at_stat_pin = 0; //use status pin + _ad9522_regs.status_pin_control = 0x1; //n divider + _ad9522_regs.ld_pin_control = 0x00; //dld + _ad9522_regs.refmon_pin_control = 0x12; //show ref2 + + _ad9522_regs.enable_ref2 = 1; + _ad9522_regs.enable_ref1 = 0; + _ad9522_regs.select_ref = ad9522_regs_t::SELECT_REF_REF2; + + _ad9522_regs.set_r_counter(r_counter); + _ad9522_regs.a_counter = a_counter; + _ad9522_regs.set_b_counter(b_counter); + _ad9522_regs.prescaler_p = ad9522_regs_t::PRESCALER_P_DIV8_9; + + _ad9522_regs.pll_power_down = ad9522_regs_t::PLL_POWER_DOWN_NORMAL; + _ad9522_regs.cp_current = ad9522_regs_t::CP_CURRENT_1_2MA; + + _ad9522_regs.vco_calibration_now = 1; //calibrate it! + _ad9522_regs.vco_divider = ad9522_regs_t::VCO_DIVIDER_DIV5; + _ad9522_regs.select_vco_or_clock = ad9522_regs_t::SELECT_VCO_OR_CLOCK_VCO; + + //setup fpga master clock + _ad9522_regs.out0_format = ad9522_regs_t::OUT0_FORMAT_LVDS; + set_clock_divider(fpga_clock_divider, + _ad9522_regs.divider0_low_cycles, + _ad9522_regs.divider0_high_cycles, + _ad9522_regs.divider0_bypass + ); + + //setup codec clock + _ad9522_regs.out3_format = ad9522_regs_t::OUT3_FORMAT_LVDS; + set_clock_divider(codec_clock_divider, + _ad9522_regs.divider1_low_cycles, + _ad9522_regs.divider1_high_cycles, + _ad9522_regs.divider1_bypass + ); + + //setup test clock (same divider as codec clock) + _ad9522_regs.out4_format = ad9522_regs_t::OUT4_FORMAT_CMOS; + _ad9522_regs.out4_cmos_configuration = (enable_test_clock)? + ad9522_regs_t::OUT4_CMOS_CONFIGURATION_A_ON : + ad9522_regs_t::OUT4_CMOS_CONFIGURATION_OFF; + + //setup a list of register ranges to write + typedef std::pair<boost::uint16_t, boost::uint16_t> range_t; + static const std::vector<range_t> ranges = boost::assign::list_of + (range_t(0x000, 0x000)) (range_t(0x010, 0x01F)) + (range_t(0x0F0, 0x0FD)) (range_t(0x190, 0x19B)) + (range_t(0x1E0, 0x1E1)) (range_t(0x230, 0x230)) + ; + + //write initial register values and latch/update + BOOST_FOREACH(const range_t &range, ranges){ + for(boost::uint16_t addr = range.first; addr <= range.second; addr++){ + this->send_reg(addr); + } + } + this->latch_regs(); + //test read: + //boost::uint32_t reg = _ad9522_regs.get_read_reg(0x01b); + //boost::uint32_t result = _iface->transact_spi( + // UE_SPI_SS_AD9522, + // spi_config_t::EDGE_RISE, + // reg, 24, true /*no*/ + //); + //std::cout << "result " << std::hex << result << std::endl; + this->enable_rx_dboard_clock(false); + this->enable_tx_dboard_clock(false); + } + + ~usrp_e100_clock_ctrl_impl(void){ + this->enable_rx_dboard_clock(false); + this->enable_tx_dboard_clock(false); + } + + double get_fpga_clock_rate(void){ + return master_clock_rate/fpga_clock_divider; + } + + /*********************************************************************** + * RX Dboard Clock Control (output 9, divider 3) + **********************************************************************/ + void enable_rx_dboard_clock(bool enb){ + _ad9522_regs.out9_format = ad9522_regs_t::OUT9_FORMAT_CMOS; + _ad9522_regs.out9_cmos_configuration = (enb)? + ad9522_regs_t::OUT9_CMOS_CONFIGURATION_B_ON : + ad9522_regs_t::OUT9_CMOS_CONFIGURATION_OFF; + this->send_reg(0x0F9); + this->latch_regs(); + } + + std::vector<double> get_rx_dboard_clock_rates(void){ + std::vector<double> rates; + for(size_t div = 1; div <= 16+16; div++) + rates.push_back(master_clock_rate/div); + return rates; + } + + void set_rx_dboard_clock_rate(double rate){ + assert_has(get_rx_dboard_clock_rates(), rate, "rx dboard clock rate"); + size_t divider = size_t(master_clock_rate/rate); + //set the divider registers + set_clock_divider(divider, + _ad9522_regs.divider3_low_cycles, + _ad9522_regs.divider3_high_cycles, + _ad9522_regs.divider3_bypass + ); + this->send_reg(0x199); + this->send_reg(0x19a); + this->latch_regs(); + } + + /*********************************************************************** + * TX Dboard Clock Control (output 6, divider 2) + **********************************************************************/ + void enable_tx_dboard_clock(bool enb){ + _ad9522_regs.out6_format = ad9522_regs_t::OUT6_FORMAT_CMOS; + _ad9522_regs.out6_cmos_configuration = (enb)? + ad9522_regs_t::OUT6_CMOS_CONFIGURATION_B_ON : + ad9522_regs_t::OUT6_CMOS_CONFIGURATION_OFF; + this->send_reg(0x0F6); + this->latch_regs(); + } + + std::vector<double> get_tx_dboard_clock_rates(void){ + return get_rx_dboard_clock_rates(); //same master clock, same dividers... + } + + void set_tx_dboard_clock_rate(double rate){ + assert_has(get_tx_dboard_clock_rates(), rate, "tx dboard clock rate"); + size_t divider = size_t(master_clock_rate/rate); + //set the divider registers + set_clock_divider(divider, + _ad9522_regs.divider2_low_cycles, + _ad9522_regs.divider2_high_cycles, + _ad9522_regs.divider2_bypass + ); + this->send_reg(0x196); + this->send_reg(0x197); + this->latch_regs(); + } + + /*********************************************************************** + * Clock reference control + **********************************************************************/ + void use_internal_ref(void) { + _ad9522_regs.enable_ref2 = 1; + _ad9522_regs.enable_ref1 = 0; + _ad9522_regs.select_ref = ad9522_regs_t::SELECT_REF_REF2; + _ad9522_regs.enb_auto_ref_switchover = ad9522_regs_t::ENB_AUTO_REF_SWITCHOVER_MANUAL; + this->send_reg(0x01C); + } + + void use_external_ref(void) { + _ad9522_regs.enable_ref2 = 0; + _ad9522_regs.enable_ref1 = 1; + _ad9522_regs.select_ref = ad9522_regs_t::SELECT_REF_REF1; + _ad9522_regs.enb_auto_ref_switchover = ad9522_regs_t::ENB_AUTO_REF_SWITCHOVER_MANUAL; + this->send_reg(0x01C); + } + + void use_auto_ref(void) { + _ad9522_regs.enable_ref2 = 1; + _ad9522_regs.enable_ref1 = 1; + _ad9522_regs.select_ref = ad9522_regs_t::SELECT_REF_REF1; + _ad9522_regs.enb_auto_ref_switchover = ad9522_regs_t::ENB_AUTO_REF_SWITCHOVER_AUTO; + } + +private: + usrp_e100_iface::sptr _iface; + ad9522_regs_t _ad9522_regs; + + void latch_regs(void){ + _ad9522_regs.io_update = 1; + this->send_reg(0x232); + } + + void send_reg(boost::uint16_t addr){ + boost::uint32_t reg = _ad9522_regs.get_write_reg(addr); + //std::cout << "clock control write reg: " << std::hex << reg << std::endl; + _iface->transact_spi( + UE_SPI_SS_AD9522, + spi_config_t::EDGE_RISE, + reg, 24, false /*no rb*/ + ); + } +}; + +/*********************************************************************** + * Clock Control Make + **********************************************************************/ +usrp_e100_clock_ctrl::sptr usrp_e100_clock_ctrl::make(usrp_e100_iface::sptr iface){ + return sptr(new usrp_e100_clock_ctrl_impl(iface)); +} diff --git a/host/lib/usrp/usrp_e100/clock_ctrl.hpp b/host/lib/usrp/usrp_e100/clock_ctrl.hpp new file mode 100644 index 000000000..d613d1473 --- /dev/null +++ b/host/lib/usrp/usrp_e100/clock_ctrl.hpp @@ -0,0 +1,103 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#ifndef INCLUDED_USRP_E100_CLOCK_CTRL_HPP +#define INCLUDED_USRP_E100_CLOCK_CTRL_HPP + +#include "usrp_e100_iface.hpp" +#include <boost/shared_ptr.hpp> +#include <boost/utility.hpp> +#include <vector> + +/*! + * The usrp-e clock control: + * - Setup system clocks. + * - Disable/enable clock lines. + */ +class usrp_e100_clock_ctrl : boost::noncopyable{ +public: + typedef boost::shared_ptr<usrp_e100_clock_ctrl> sptr; + + /*! + * Make a new clock control object. + * \param iface the usrp_e100 iface object + * \return the clock control object + */ + static sptr make(usrp_e100_iface::sptr iface); + + /*! + * Get the rate of the fpga clock line. + * \return the fpga clock rate in Hz + */ + virtual double get_fpga_clock_rate(void) = 0; + + /*! + * Get the possible rates of the rx dboard clock. + * \return a vector of clock rates in Hz + */ + virtual std::vector<double> get_rx_dboard_clock_rates(void) = 0; + + /*! + * Get the possible rates of the tx dboard clock. + * \return a vector of clock rates in Hz + */ + virtual std::vector<double> get_tx_dboard_clock_rates(void) = 0; + + /*! + * Set the rx dboard clock rate to a possible rate. + * \param rate the new clock rate in Hz + * \throw exception when rate cannot be achieved + */ + virtual void set_rx_dboard_clock_rate(double rate) = 0; + + /*! + * Set the tx dboard clock rate to a possible rate. + * \param rate the new clock rate in Hz + * \throw exception when rate cannot be achieved + */ + virtual void set_tx_dboard_clock_rate(double rate) = 0; + + /*! + * Enable/disable the rx dboard clock. + * \param enb true to enable + */ + virtual void enable_rx_dboard_clock(bool enb) = 0; + + /*! + * Enable/disable the tx dboard clock. + * \param enb true to enable + */ + virtual void enable_tx_dboard_clock(bool enb) = 0; + + /*! + * Use the internal TCXO reference + */ + virtual void use_internal_ref(void) = 0; + + /*! + * Use the external SMA reference + */ + virtual void use_external_ref(void) = 0; + + /*! + * Use external if available, internal otherwise + */ + virtual void use_auto_ref(void) = 0; + +}; + +#endif /* INCLUDED_USRP_E100_CLOCK_CTRL_HPP */ diff --git a/host/lib/usrp/usrp_e100/codec_ctrl.cpp b/host/lib/usrp/usrp_e100/codec_ctrl.cpp new file mode 100644 index 000000000..e7fd9792e --- /dev/null +++ b/host/lib/usrp/usrp_e100/codec_ctrl.cpp @@ -0,0 +1,296 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include "codec_ctrl.hpp" +#include "ad9862_regs.hpp" +#include <uhd/types/dict.hpp> +#include <uhd/utils/assert.hpp> +#include <uhd/utils/algorithm.hpp> +#include <boost/cstdint.hpp> +#include <boost/tuple/tuple.hpp> +#include <boost/math/special_functions/round.hpp> +#include "usrp_e100_regs.hpp" //spi slave constants +#include <boost/assign/list_of.hpp> +#include <iostream> + +using namespace uhd; + +static const bool codec_debug = false; + +const gain_range_t usrp_e100_codec_ctrl::tx_pga_gain_range(-20, 0, float(0.1)); +const gain_range_t usrp_e100_codec_ctrl::rx_pga_gain_range(0, 20, 1); + +/*********************************************************************** + * Codec Control Implementation + **********************************************************************/ +class usrp_e100_codec_ctrl_impl : public usrp_e100_codec_ctrl{ +public: + //structors + usrp_e100_codec_ctrl_impl(usrp_e100_iface::sptr iface); + ~usrp_e100_codec_ctrl_impl(void); + + //aux adc and dac control + float read_aux_adc(aux_adc_t which); + void write_aux_dac(aux_dac_t which, float volts); + + //pga gain control + void set_tx_pga_gain(float); + float get_tx_pga_gain(void); + void set_rx_pga_gain(float, char); + float get_rx_pga_gain(char); + +private: + usrp_e100_iface::sptr _iface; + ad9862_regs_t _ad9862_regs; + aux_adc_t _last_aux_adc_a, _last_aux_adc_b; + void send_reg(boost::uint8_t addr); + void recv_reg(boost::uint8_t addr); +}; + +/*********************************************************************** + * Codec Control Structors + **********************************************************************/ +usrp_e100_codec_ctrl_impl::usrp_e100_codec_ctrl_impl(usrp_e100_iface::sptr iface){ + _iface = iface; + + //soft reset + _ad9862_regs.soft_reset = 1; + this->send_reg(0); + + //initialize the codec register settings + _ad9862_regs.sdio_bidir = ad9862_regs_t::SDIO_BIDIR_SDIO_SDO; + _ad9862_regs.lsb_first = ad9862_regs_t::LSB_FIRST_MSB; + _ad9862_regs.soft_reset = 0; + + //setup rx side of codec + _ad9862_regs.byp_buffer_a = 1; + _ad9862_regs.byp_buffer_b = 1; + _ad9862_regs.buffer_a_pd = 1; + _ad9862_regs.buffer_b_pd = 1; + _ad9862_regs.rx_pga_a = 0;//0x1f; //TODO bring under api control + _ad9862_regs.rx_pga_b = 0;//0x1f; //TODO bring under api control + _ad9862_regs.rx_twos_comp = 1; + _ad9862_regs.rx_hilbert = ad9862_regs_t::RX_HILBERT_DIS; + + //setup tx side of codec + _ad9862_regs.two_data_paths = ad9862_regs_t::TWO_DATA_PATHS_BOTH; + _ad9862_regs.interleaved = ad9862_regs_t::INTERLEAVED_INTERLEAVED; + _ad9862_regs.tx_retime = ad9862_regs_t::TX_RETIME_CLKOUT2; + _ad9862_regs.tx_pga_gain = 199; //TODO bring under api control + _ad9862_regs.tx_hilbert = ad9862_regs_t::TX_HILBERT_DIS; + _ad9862_regs.interp = ad9862_regs_t::INTERP_2; + _ad9862_regs.tx_twos_comp = 1; + _ad9862_regs.fine_mode = ad9862_regs_t::FINE_MODE_BYPASS; + _ad9862_regs.coarse_mod = ad9862_regs_t::COARSE_MOD_BYPASS; + _ad9862_regs.dac_a_coarse_gain = 0x3; + _ad9862_regs.dac_b_coarse_gain = 0x3; + _ad9862_regs.edges = ad9862_regs_t::EDGES_NORMAL; + + //setup the dll + _ad9862_regs.input_clk_ctrl = ad9862_regs_t::INPUT_CLK_CTRL_EXTERNAL; + _ad9862_regs.dll_mult = ad9862_regs_t::DLL_MULT_2; + _ad9862_regs.dll_mode = ad9862_regs_t::DLL_MODE_FAST; + + //write the register settings to the codec + for (uint8_t addr = 0; addr <= 25; addr++){ + this->send_reg(addr); + } + + //aux adc clock + _ad9862_regs.clk_4 = ad9862_regs_t::CLK_4_1_4; + this->send_reg(34); +} + +usrp_e100_codec_ctrl_impl::~usrp_e100_codec_ctrl_impl(void){ + //set aux dacs to zero + this->write_aux_dac(AUX_DAC_A, 0); + this->write_aux_dac(AUX_DAC_B, 0); + this->write_aux_dac(AUX_DAC_C, 0); + this->write_aux_dac(AUX_DAC_D, 0); + + //power down + _ad9862_regs.all_rx_pd = 1; + this->send_reg(1); + _ad9862_regs.tx_digital_pd = 1; + _ad9862_regs.tx_analog_pd = ad9862_regs_t::TX_ANALOG_PD_BOTH; + this->send_reg(8); +} + +/*********************************************************************** + * Codec Control Gain Control Methods + **********************************************************************/ +static const int mtpgw = 255; //maximum tx pga gain word + +void usrp_e100_codec_ctrl_impl::set_tx_pga_gain(float gain){ + int gain_word = int(mtpgw*(gain - tx_pga_gain_range.min)/(tx_pga_gain_range.max - tx_pga_gain_range.min)); + _ad9862_regs.tx_pga_gain = std::clip(gain_word, 0, mtpgw); + this->send_reg(16); +} + +float usrp_e100_codec_ctrl_impl::get_tx_pga_gain(void){ + return (_ad9862_regs.tx_pga_gain*(tx_pga_gain_range.max - tx_pga_gain_range.min)/mtpgw) + tx_pga_gain_range.min; +} + +static const int mrpgw = 0x14; //maximum rx pga gain word + +void usrp_e100_codec_ctrl_impl::set_rx_pga_gain(float gain, char which){ + int gain_word = int(mrpgw*(gain - rx_pga_gain_range.min)/(rx_pga_gain_range.max - rx_pga_gain_range.min)); + gain_word = std::clip(gain_word, 0, mrpgw); + switch(which){ + case 'A': + _ad9862_regs.rx_pga_a = gain_word; + this->send_reg(2); + return; + case 'B': + _ad9862_regs.rx_pga_b = gain_word; + this->send_reg(3); + return; + default: UHD_THROW_INVALID_CODE_PATH(); + } +} + +float usrp_e100_codec_ctrl_impl::get_rx_pga_gain(char which){ + int gain_word; + switch(which){ + case 'A': gain_word = _ad9862_regs.rx_pga_a; break; + case 'B': gain_word = _ad9862_regs.rx_pga_b; break; + default: UHD_THROW_INVALID_CODE_PATH(); + } + return (gain_word*(rx_pga_gain_range.max - rx_pga_gain_range.min)/mrpgw) + rx_pga_gain_range.min; +} + +/*********************************************************************** + * Codec Control AUX ADC Methods + **********************************************************************/ +static float aux_adc_to_volts(boost::uint8_t high, boost::uint8_t low){ + return float((boost::uint16_t(high) << 2) | low)*3.3/0x3ff; +} + +float usrp_e100_codec_ctrl_impl::read_aux_adc(aux_adc_t which){ + //check to see if the switch needs to be set + bool write_switch = false; + switch(which){ + + case AUX_ADC_A1: + case AUX_ADC_A2: + if (which != _last_aux_adc_a){ + _ad9862_regs.select_a = (which == AUX_ADC_A1)? + ad9862_regs_t::SELECT_A_AUX_ADC1: ad9862_regs_t::SELECT_A_AUX_ADC2; + _last_aux_adc_a = which; + write_switch = true; + } + break; + + case AUX_ADC_B1: + case AUX_ADC_B2: + if (which != _last_aux_adc_b){ + _ad9862_regs.select_b = (which == AUX_ADC_B1)? + ad9862_regs_t::SELECT_B_AUX_ADC1: ad9862_regs_t::SELECT_B_AUX_ADC2; + _last_aux_adc_b = which; + write_switch = true; + } + break; + + } + + //write the switch if it changed + if(write_switch) this->send_reg(34); + + //map aux adcs to register values to read + static const uhd::dict<aux_adc_t, boost::uint8_t> aux_dac_to_addr = boost::assign::map_list_of + (AUX_ADC_A2, 26) (AUX_ADC_A1, 28) + (AUX_ADC_B2, 30) (AUX_ADC_B1, 32) + ; + + //read the value + this->recv_reg(aux_dac_to_addr[which]+0); + this->recv_reg(aux_dac_to_addr[which]+1); + + //return the value scaled to volts + switch(which){ + case AUX_ADC_A1: return aux_adc_to_volts(_ad9862_regs.aux_adc_a1_9_2, _ad9862_regs.aux_adc_a1_1_0); + case AUX_ADC_A2: return aux_adc_to_volts(_ad9862_regs.aux_adc_a2_9_2, _ad9862_regs.aux_adc_a2_1_0); + case AUX_ADC_B1: return aux_adc_to_volts(_ad9862_regs.aux_adc_b1_9_2, _ad9862_regs.aux_adc_b1_1_0); + case AUX_ADC_B2: return aux_adc_to_volts(_ad9862_regs.aux_adc_b2_9_2, _ad9862_regs.aux_adc_b2_1_0); + } + UHD_ASSERT_THROW(false); +} + +/*********************************************************************** + * Codec Control AUX DAC Methods + **********************************************************************/ +void usrp_e100_codec_ctrl_impl::write_aux_dac(aux_dac_t which, float volts){ + //special case for aux dac d (aka sigma delta word) + if (which == AUX_DAC_D){ + boost::uint16_t dac_word = std::clip(boost::math::iround(volts*0xfff/3.3), 0, 0xfff); + _ad9862_regs.sig_delt_11_4 = boost::uint8_t(dac_word >> 4); + _ad9862_regs.sig_delt_3_0 = boost::uint8_t(dac_word & 0xf); + this->send_reg(42); + this->send_reg(43); + return; + } + + //calculate the dac word for aux dac a, b, c + boost::uint8_t dac_word = std::clip(boost::math::iround(volts*0xff/3.3), 0, 0xff); + + //setup a lookup table for the aux dac params (reg ref, reg addr) + typedef boost::tuple<boost::uint8_t*, boost::uint8_t> dac_params_t; + uhd::dict<aux_dac_t, dac_params_t> aux_dac_to_params = boost::assign::map_list_of + (AUX_DAC_A, dac_params_t(&_ad9862_regs.aux_dac_a, 36)) + (AUX_DAC_B, dac_params_t(&_ad9862_regs.aux_dac_b, 37)) + (AUX_DAC_C, dac_params_t(&_ad9862_regs.aux_dac_c, 38)) + ; + + //set the aux dac register + UHD_ASSERT_THROW(aux_dac_to_params.has_key(which)); + boost::uint8_t *reg_ref, reg_addr; + boost::tie(reg_ref, reg_addr) = aux_dac_to_params[which]; + *reg_ref = dac_word; + this->send_reg(reg_addr); +} + +/*********************************************************************** + * Codec Control SPI Methods + **********************************************************************/ +void usrp_e100_codec_ctrl_impl::send_reg(boost::uint8_t addr){ + boost::uint32_t reg = _ad9862_regs.get_write_reg(addr); + if (codec_debug) std::cout << "codec control write reg: " << std::hex << reg << std::endl; + _iface->transact_spi( + UE_SPI_SS_AD9862, + spi_config_t::EDGE_RISE, + reg, 16, false /*no rb*/ + ); +} + +void usrp_e100_codec_ctrl_impl::recv_reg(boost::uint8_t addr){ + boost::uint32_t reg = _ad9862_regs.get_read_reg(addr); + if (codec_debug) std::cout << "codec control read reg: " << std::hex << reg << std::endl; + boost::uint32_t ret = _iface->transact_spi( + UE_SPI_SS_AD9862, + spi_config_t::EDGE_RISE, + reg, 16, true /*rb*/ + ); + if (codec_debug) std::cout << "codec control read ret: " << std::hex << ret << std::endl; + _ad9862_regs.set_reg(addr, boost::uint16_t(ret)); +} + +/*********************************************************************** + * Codec Control Make + **********************************************************************/ +usrp_e100_codec_ctrl::sptr usrp_e100_codec_ctrl::make(usrp_e100_iface::sptr iface){ + return sptr(new usrp_e100_codec_ctrl_impl(iface)); +} diff --git a/host/lib/usrp/usrp_e100/codec_ctrl.hpp b/host/lib/usrp/usrp_e100/codec_ctrl.hpp new file mode 100644 index 000000000..74ce9bd9a --- /dev/null +++ b/host/lib/usrp/usrp_e100/codec_ctrl.hpp @@ -0,0 +1,90 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#ifndef INCLUDED_USRP_E100_CODEC_CTRL_HPP +#define INCLUDED_USRP_E100_CODEC_CTRL_HPP + +#include "usrp_e100_iface.hpp" +#include <uhd/types/ranges.hpp> +#include <boost/shared_ptr.hpp> +#include <boost/utility.hpp> + +/*! + * The usrp-e codec control: + * - Init/power down codec. + * - Read aux adc, write aux dac. + */ +class usrp_e100_codec_ctrl : boost::noncopyable{ +public: + typedef boost::shared_ptr<usrp_e100_codec_ctrl> sptr; + + static const uhd::gain_range_t tx_pga_gain_range; + static const uhd::gain_range_t rx_pga_gain_range; + + /*! + * Make a new codec control object. + * \param iface the usrp_e100 iface object + * \return the codec control object + */ + static sptr make(usrp_e100_iface::sptr iface); + + //! aux adc identifier constants + enum aux_adc_t{ + AUX_ADC_A2 = 0xA2, + AUX_ADC_A1 = 0xA1, + AUX_ADC_B2 = 0xB2, + AUX_ADC_B1 = 0xB1 + }; + + /*! + * Read an auxiliary adc: + * The internals remember which aux adc was read last. + * Therefore, the aux adc switch is only changed as needed. + * \param which which of the 4 adcs + * \return a value in volts + */ + virtual float read_aux_adc(aux_adc_t which) = 0; + + //! aux dac identifier constants + enum aux_dac_t{ + AUX_DAC_A = 0xA, + AUX_DAC_B = 0xB, + AUX_DAC_C = 0xC, + AUX_DAC_D = 0xD //really the sigma delta output + }; + + /*! + * Write an auxiliary dac. + * \param which which of the 4 dacs + * \param volts the level in in volts + */ + virtual void write_aux_dac(aux_dac_t which, float volts) = 0; + + //! Set the TX PGA gain + virtual void set_tx_pga_gain(float gain) = 0; + + //! Get the TX PGA gain + virtual float get_tx_pga_gain(void) = 0; + + //! Set the RX PGA gain ('A' or 'B') + virtual void set_rx_pga_gain(float gain, char which) = 0; + + //! Get the RX PGA gain ('A' or 'B') + virtual float get_rx_pga_gain(char which) = 0; +}; + +#endif /* INCLUDED_USRP_E100_CODEC_CTRL_HPP */ diff --git a/host/lib/usrp/usrp_e100/codec_impl.cpp b/host/lib/usrp/usrp_e100/codec_impl.cpp new file mode 100644 index 000000000..6fd44bad3 --- /dev/null +++ b/host/lib/usrp/usrp_e100/codec_impl.cpp @@ -0,0 +1,149 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include "usrp_e100_impl.hpp" +#include <uhd/utils/assert.hpp> +#include <uhd/usrp/codec_props.hpp> +#include <boost/bind.hpp> + +using namespace uhd; +using namespace uhd::usrp; + +/*********************************************************************** + * Helper Methods + **********************************************************************/ +void usrp_e100_impl::codec_init(void){ + //make proxies + _rx_codec_proxy = wax_obj_proxy::make( + boost::bind(&usrp_e100_impl::rx_codec_get, this, _1, _2), + boost::bind(&usrp_e100_impl::rx_codec_set, this, _1, _2) + ); + _tx_codec_proxy = wax_obj_proxy::make( + boost::bind(&usrp_e100_impl::tx_codec_get, this, _1, _2), + boost::bind(&usrp_e100_impl::tx_codec_set, this, _1, _2) + ); +} + +/*********************************************************************** + * RX Codec Properties + **********************************************************************/ +static const std::string ad9862_pga_gain_name = "ad9862 pga"; + +void usrp_e100_impl::rx_codec_get(const wax::obj &key_, wax::obj &val){ + named_prop_t key = named_prop_t::extract(key_); + + //handle the get request conditioned on the key + switch(key.as<codec_prop_t>()){ + case CODEC_PROP_NAME: + val = std::string("usrp-e adc - ad9522"); + return; + + case CODEC_PROP_OTHERS: + val = prop_names_t(); + return; + + case CODEC_PROP_GAIN_NAMES: + val = prop_names_t(1, ad9862_pga_gain_name); + return; + + case CODEC_PROP_GAIN_RANGE: + UHD_ASSERT_THROW(key.name == ad9862_pga_gain_name); + val = usrp_e100_codec_ctrl::rx_pga_gain_range; + return; + + case CODEC_PROP_GAIN_I: + UHD_ASSERT_THROW(key.name == ad9862_pga_gain_name); + val = _codec_ctrl->get_rx_pga_gain('A'); + return; + + case CODEC_PROP_GAIN_Q: + UHD_ASSERT_THROW(key.name == ad9862_pga_gain_name); + val = _codec_ctrl->get_rx_pga_gain('B'); + return; + + default: UHD_THROW_PROP_GET_ERROR(); + } +} + +void usrp_e100_impl::rx_codec_set(const wax::obj &key_, const wax::obj &val){ + named_prop_t key = named_prop_t::extract(key_); + + //handle the set request conditioned on the key + switch(key.as<codec_prop_t>()){ + case CODEC_PROP_GAIN_I: + UHD_ASSERT_THROW(key.name == ad9862_pga_gain_name); + _codec_ctrl->set_rx_pga_gain(val.as<float>(), 'A'); + return; + + case CODEC_PROP_GAIN_Q: + UHD_ASSERT_THROW(key.name == ad9862_pga_gain_name); + _codec_ctrl->set_rx_pga_gain(val.as<float>(), 'B'); + return; + + default: UHD_THROW_PROP_SET_ERROR(); + } +} + +/*********************************************************************** + * TX Codec Properties + **********************************************************************/ +void usrp_e100_impl::tx_codec_get(const wax::obj &key_, wax::obj &val){ + named_prop_t key = named_prop_t::extract(key_); + + //handle the get request conditioned on the key + switch(key.as<codec_prop_t>()){ + case CODEC_PROP_NAME: + val = std::string("usrp-e dac - ad9522"); + return; + + case CODEC_PROP_OTHERS: + val = prop_names_t(); + return; + + case CODEC_PROP_GAIN_NAMES: + val = prop_names_t(1, ad9862_pga_gain_name); + return; + + case CODEC_PROP_GAIN_RANGE: + UHD_ASSERT_THROW(key.name == ad9862_pga_gain_name); + val = usrp_e100_codec_ctrl::tx_pga_gain_range; + return; + + case CODEC_PROP_GAIN_I: //only one gain for I and Q + case CODEC_PROP_GAIN_Q: + UHD_ASSERT_THROW(key.name == ad9862_pga_gain_name); + val = _codec_ctrl->get_tx_pga_gain(); + return; + + default: UHD_THROW_PROP_GET_ERROR(); + } +} + +void usrp_e100_impl::tx_codec_set(const wax::obj &key_, const wax::obj &val){ + named_prop_t key = named_prop_t::extract(key_); + + //handle the set request conditioned on the key + switch(key.as<codec_prop_t>()){ + case CODEC_PROP_GAIN_I: //only one gain for I and Q + case CODEC_PROP_GAIN_Q: + UHD_ASSERT_THROW(key.name == ad9862_pga_gain_name); + _codec_ctrl->set_tx_pga_gain(val.as<float>()); + return; + + default: UHD_THROW_PROP_SET_ERROR(); + } +} diff --git a/host/lib/usrp/usrp_e100/dboard_iface.cpp b/host/lib/usrp/usrp_e100/dboard_iface.cpp new file mode 100644 index 000000000..aa96171d6 --- /dev/null +++ b/host/lib/usrp/usrp_e100/dboard_iface.cpp @@ -0,0 +1,298 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include "usrp_e100_iface.hpp" +#include "usrp_e100_regs.hpp" +#include "clock_ctrl.hpp" +#include "codec_ctrl.hpp" +#include <uhd/usrp/dboard_iface.hpp> +#include <uhd/types/dict.hpp> +#include <uhd/utils/assert.hpp> +#include <boost/assign/list_of.hpp> +#include <linux/usrp_e.h> //i2c and spi constants + +using namespace uhd; +using namespace uhd::usrp; +using namespace boost::assign; + +class usrp_e100_dboard_iface : public dboard_iface{ +public: + + usrp_e100_dboard_iface( + usrp_e100_iface::sptr iface, + usrp_e100_clock_ctrl::sptr clock, + usrp_e100_codec_ctrl::sptr codec + ){ + _iface = iface; + _clock = clock; + _codec = codec; + + //init the clock rate shadows + this->set_clock_rate(UNIT_RX, _clock->get_fpga_clock_rate()); + this->set_clock_rate(UNIT_TX, _clock->get_fpga_clock_rate()); + + _iface->poke16(UE_REG_GPIO_RX_DBG, 0); + _iface->poke16(UE_REG_GPIO_TX_DBG, 0); + } + + ~usrp_e100_dboard_iface(void){ + /* NOP */ + } + + special_props_t get_special_props(void){ + special_props_t props; + props.soft_clock_divider = false; + props.mangle_i2c_addrs = false; + return props; + } + + void write_aux_dac(unit_t, aux_dac_t, float); + float read_aux_adc(unit_t, aux_adc_t); + + void set_pin_ctrl(unit_t, boost::uint16_t); + void set_atr_reg(unit_t, atr_reg_t, boost::uint16_t); + void set_gpio_ddr(unit_t, boost::uint16_t); + void write_gpio(unit_t, boost::uint16_t); + void set_gpio_debug(unit_t, int); + boost::uint16_t read_gpio(unit_t); + + void write_i2c(boost::uint8_t, const byte_vector_t &); + byte_vector_t read_i2c(boost::uint8_t, size_t); + + void write_spi( + unit_t unit, + const spi_config_t &config, + boost::uint32_t data, + size_t num_bits + ); + + boost::uint32_t read_write_spi( + unit_t unit, + const spi_config_t &config, + boost::uint32_t data, + size_t num_bits + ); + + void set_clock_rate(unit_t, double); + std::vector<double> get_clock_rates(unit_t); + double get_clock_rate(unit_t); + void set_clock_enabled(unit_t, bool); + double get_codec_rate(unit_t); + +private: + usrp_e100_iface::sptr _iface; + usrp_e100_clock_ctrl::sptr _clock; + usrp_e100_codec_ctrl::sptr _codec; + uhd::dict<unit_t, double> _clock_rates; +}; + +/*********************************************************************** + * Make Function + **********************************************************************/ +dboard_iface::sptr make_usrp_e100_dboard_iface( + usrp_e100_iface::sptr iface, + usrp_e100_clock_ctrl::sptr clock, + usrp_e100_codec_ctrl::sptr codec +){ + return dboard_iface::sptr(new usrp_e100_dboard_iface(iface, clock, codec)); +} + +/*********************************************************************** + * Clock Rates + **********************************************************************/ +void usrp_e100_dboard_iface::set_clock_rate(unit_t unit, double rate){ + _clock_rates[unit] = rate; + switch(unit){ + case UNIT_RX: return _clock->set_rx_dboard_clock_rate(rate); + case UNIT_TX: return _clock->set_tx_dboard_clock_rate(rate); + } +} + +std::vector<double> usrp_e100_dboard_iface::get_clock_rates(unit_t unit){ + switch(unit){ + case UNIT_RX: return _clock->get_rx_dboard_clock_rates(); + case UNIT_TX: return _clock->get_tx_dboard_clock_rates(); + default: UHD_THROW_INVALID_CODE_PATH(); + } +} + +double usrp_e100_dboard_iface::get_clock_rate(unit_t unit){ + return _clock_rates[unit]; +} + +void usrp_e100_dboard_iface::set_clock_enabled(unit_t unit, bool enb){ + switch(unit){ + case UNIT_RX: return _clock->enable_rx_dboard_clock(enb); + case UNIT_TX: return _clock->enable_tx_dboard_clock(enb); + } +} + +double usrp_e100_dboard_iface::get_codec_rate(unit_t){ + return _clock->get_fpga_clock_rate(); +} + +/*********************************************************************** + * GPIO + **********************************************************************/ +void usrp_e100_dboard_iface::set_pin_ctrl(unit_t unit, boost::uint16_t value){ + UHD_ASSERT_THROW(GPIO_SEL_ATR == 1); //make this assumption + switch(unit){ + case UNIT_RX: _iface->poke16(UE_REG_GPIO_RX_SEL, value); return; + case UNIT_TX: _iface->poke16(UE_REG_GPIO_TX_SEL, value); return; + } +} + +void usrp_e100_dboard_iface::set_gpio_ddr(unit_t unit, boost::uint16_t value){ + switch(unit){ + case UNIT_RX: _iface->poke16(UE_REG_GPIO_RX_DDR, value); return; + case UNIT_TX: _iface->poke16(UE_REG_GPIO_TX_DDR, value); return; + } +} + +void usrp_e100_dboard_iface::write_gpio(unit_t unit, boost::uint16_t value){ + switch(unit){ + case UNIT_RX: _iface->poke16(UE_REG_GPIO_RX_IO, value); return; + case UNIT_TX: _iface->poke16(UE_REG_GPIO_TX_IO, value); return; + } +} + +boost::uint16_t usrp_e100_dboard_iface::read_gpio(unit_t unit){ + switch(unit){ + case UNIT_RX: return _iface->peek16(UE_REG_GPIO_RX_IO); + case UNIT_TX: return _iface->peek16(UE_REG_GPIO_TX_IO); + default: UHD_THROW_INVALID_CODE_PATH(); + } +} + +void usrp_e100_dboard_iface::set_atr_reg(unit_t unit, atr_reg_t atr, boost::uint16_t value){ + //define mapping of unit to atr regs to register address + static const uhd::dict< + unit_t, uhd::dict<atr_reg_t, boost::uint32_t> + > unit_to_atr_to_addr = map_list_of + (UNIT_RX, map_list_of + (ATR_REG_IDLE, UE_REG_ATR_IDLE_RXSIDE) + (ATR_REG_TX_ONLY, UE_REG_ATR_INTX_RXSIDE) + (ATR_REG_RX_ONLY, UE_REG_ATR_INRX_RXSIDE) + (ATR_REG_FULL_DUPLEX, UE_REG_ATR_FULL_RXSIDE) + ) + (UNIT_TX, map_list_of + (ATR_REG_IDLE, UE_REG_ATR_IDLE_TXSIDE) + (ATR_REG_TX_ONLY, UE_REG_ATR_INTX_TXSIDE) + (ATR_REG_RX_ONLY, UE_REG_ATR_INRX_TXSIDE) + (ATR_REG_FULL_DUPLEX, UE_REG_ATR_FULL_TXSIDE) + ) + ; + _iface->poke16(unit_to_atr_to_addr[unit][atr], value); +} + +void usrp_e100_dboard_iface::set_gpio_debug(unit_t unit, int which){ + //set this unit to all outputs + this->set_gpio_ddr(unit, 0xffff); + + //calculate the debug selections + boost::uint32_t dbg_sels = 0x0; + int sel = (which == 0)? GPIO_SEL_DEBUG_0 : GPIO_SEL_DEBUG_1; + for(size_t i = 0; i < 16; i++) dbg_sels |= sel << i; + + //set the debug on and which debug selection + switch(unit){ + case UNIT_RX: + _iface->poke16(UE_REG_GPIO_RX_DBG, 0xffff); + _iface->poke16(UE_REG_GPIO_RX_SEL, dbg_sels); + return; + + case UNIT_TX: + _iface->poke16(UE_REG_GPIO_TX_DBG, 0xffff); + _iface->poke16(UE_REG_GPIO_TX_SEL, dbg_sels); + return; + } +} + +/*********************************************************************** + * SPI + **********************************************************************/ +/*! + * Static function to convert a unit type to a spi slave device number. + * \param unit the dboard interface unit type enum + * \return the slave device number + */ +static boost::uint32_t unit_to_otw_spi_dev(dboard_iface::unit_t unit){ + switch(unit){ + case dboard_iface::UNIT_TX: return UE_SPI_SS_TX_DB; + case dboard_iface::UNIT_RX: return UE_SPI_SS_RX_DB; + } + throw std::invalid_argument("unknown unit type"); +} + +void usrp_e100_dboard_iface::write_spi( + unit_t unit, + const spi_config_t &config, + boost::uint32_t data, + size_t num_bits +){ + _iface->transact_spi(unit_to_otw_spi_dev(unit), config, data, num_bits, false /*no rb*/); +} + +boost::uint32_t usrp_e100_dboard_iface::read_write_spi( + unit_t unit, + const spi_config_t &config, + boost::uint32_t data, + size_t num_bits +){ + return _iface->transact_spi(unit_to_otw_spi_dev(unit), config, data, num_bits, true /*rb*/); +} + +/*********************************************************************** + * I2C + **********************************************************************/ +void usrp_e100_dboard_iface::write_i2c(boost::uint8_t addr, const byte_vector_t &bytes){ + return _iface->write_i2c(addr, bytes); +} + +byte_vector_t usrp_e100_dboard_iface::read_i2c(boost::uint8_t addr, size_t num_bytes){ + return _iface->read_i2c(addr, num_bytes); +} + +/*********************************************************************** + * Aux DAX/ADC + **********************************************************************/ +void usrp_e100_dboard_iface::write_aux_dac(dboard_iface::unit_t, aux_dac_t which, float value){ + //same aux dacs for each unit + static const uhd::dict<aux_dac_t, usrp_e100_codec_ctrl::aux_dac_t> which_to_aux_dac = map_list_of + (AUX_DAC_A, usrp_e100_codec_ctrl::AUX_DAC_A) + (AUX_DAC_B, usrp_e100_codec_ctrl::AUX_DAC_B) + (AUX_DAC_C, usrp_e100_codec_ctrl::AUX_DAC_C) + (AUX_DAC_D, usrp_e100_codec_ctrl::AUX_DAC_D) + ; + _codec->write_aux_dac(which_to_aux_dac[which], value); +} + +float usrp_e100_dboard_iface::read_aux_adc(dboard_iface::unit_t unit, aux_adc_t which){ + static const uhd::dict< + unit_t, uhd::dict<aux_adc_t, usrp_e100_codec_ctrl::aux_adc_t> + > unit_to_which_to_aux_adc = map_list_of + (UNIT_RX, map_list_of + (AUX_ADC_A, usrp_e100_codec_ctrl::AUX_ADC_A1) + (AUX_ADC_B, usrp_e100_codec_ctrl::AUX_ADC_B1) + ) + (UNIT_TX, map_list_of + (AUX_ADC_A, usrp_e100_codec_ctrl::AUX_ADC_A2) + (AUX_ADC_B, usrp_e100_codec_ctrl::AUX_ADC_B2) + ) + ; + return _codec->read_aux_adc(unit_to_which_to_aux_adc[unit][which]); +} diff --git a/host/lib/usrp/usrp_e100/dboard_impl.cpp b/host/lib/usrp/usrp_e100/dboard_impl.cpp new file mode 100644 index 000000000..9f2bfb8ae --- /dev/null +++ b/host/lib/usrp/usrp_e100/dboard_impl.cpp @@ -0,0 +1,172 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include "usrp_e100_impl.hpp" +#include "usrp_e100_regs.hpp" +#include <uhd/utils/assert.hpp> +#include <uhd/usrp/dboard_props.hpp> +#include <uhd/usrp/subdev_props.hpp> +#include <uhd/usrp/misc_utils.hpp> +#include <boost/bind.hpp> +#include <iostream> + +using namespace uhd; +using namespace uhd::usrp; + +/*********************************************************************** + * Dboard Initialization + **********************************************************************/ +void usrp_e100_impl::dboard_init(void){ + _rx_db_eeprom = dboard_eeprom_t(_iface->read_eeprom(I2C_ADDR_RX_DB, 0, dboard_eeprom_t::num_bytes())); + _tx_db_eeprom = dboard_eeprom_t(_iface->read_eeprom(I2C_ADDR_TX_DB, 0, dboard_eeprom_t::num_bytes())); + + //create a new dboard interface and manager + _dboard_iface = make_usrp_e100_dboard_iface( + _iface, _clock_ctrl, _codec_ctrl + ); + _dboard_manager = dboard_manager::make( + _rx_db_eeprom.id, _tx_db_eeprom.id, _dboard_iface + ); + + //setup the dboard proxies + _rx_dboard_proxy = wax_obj_proxy::make( + boost::bind(&usrp_e100_impl::rx_dboard_get, this, _1, _2), + boost::bind(&usrp_e100_impl::rx_dboard_set, this, _1, _2) + ); + _tx_dboard_proxy = wax_obj_proxy::make( + boost::bind(&usrp_e100_impl::tx_dboard_get, this, _1, _2), + boost::bind(&usrp_e100_impl::tx_dboard_set, this, _1, _2) + ); +} + +/*********************************************************************** + * RX Dboard Get + **********************************************************************/ +void usrp_e100_impl::rx_dboard_get(const wax::obj &key_, wax::obj &val){ + named_prop_t key = named_prop_t::extract(key_); + + //handle the get request conditioned on the key + switch(key.as<dboard_prop_t>()){ + case DBOARD_PROP_NAME: + val = std::string("usrp-e dboard (rx unit)"); + return; + + case DBOARD_PROP_SUBDEV: + val = _dboard_manager->get_rx_subdev(key.name); + return; + + case DBOARD_PROP_SUBDEV_NAMES: + val = _dboard_manager->get_rx_subdev_names(); + return; + + case DBOARD_PROP_DBOARD_ID: + val = _rx_db_eeprom.id; + return; + + case DBOARD_PROP_DBOARD_IFACE: + val = _dboard_iface; + return; + + case DBOARD_PROP_CODEC: + val = _rx_codec_proxy->get_link(); + return; + + case DBOARD_PROP_GAIN_GROUP: + val = make_gain_group( + _rx_db_eeprom.id, + _dboard_manager->get_rx_subdev(key.name), + _rx_codec_proxy->get_link(), + GAIN_GROUP_POLICY_RX + ); + return; + + default: UHD_THROW_PROP_GET_ERROR(); + } +} + +/*********************************************************************** + * RX Dboard Set + **********************************************************************/ +void usrp_e100_impl::rx_dboard_set(const wax::obj &key, const wax::obj &val){ + switch(key.as<dboard_prop_t>()){ + case DBOARD_PROP_DBOARD_ID: + _rx_db_eeprom.id = val.as<dboard_id_t>(); + _iface->write_eeprom(I2C_ADDR_RX_DB, 0, _rx_db_eeprom.get_eeprom_bytes()); + return; + + default: UHD_THROW_PROP_SET_ERROR(); + } +} + +/*********************************************************************** + * TX Dboard Get + **********************************************************************/ +void usrp_e100_impl::tx_dboard_get(const wax::obj &key_, wax::obj &val){ + named_prop_t key = named_prop_t::extract(key_); + + //handle the get request conditioned on the key + switch(key.as<dboard_prop_t>()){ + case DBOARD_PROP_NAME: + val = std::string("usrp-e dboard (tx unit)"); + return; + + case DBOARD_PROP_SUBDEV: + val = _dboard_manager->get_tx_subdev(key.name); + return; + + case DBOARD_PROP_SUBDEV_NAMES: + val = _dboard_manager->get_tx_subdev_names(); + return; + + case DBOARD_PROP_DBOARD_ID: + val = _tx_db_eeprom.id; + return; + + case DBOARD_PROP_DBOARD_IFACE: + val = _dboard_iface; + return; + + case DBOARD_PROP_CODEC: + val = _tx_codec_proxy->get_link(); + return; + + case DBOARD_PROP_GAIN_GROUP: + val = make_gain_group( + _tx_db_eeprom.id, + _dboard_manager->get_tx_subdev(key.name), + _tx_codec_proxy->get_link(), + GAIN_GROUP_POLICY_TX + ); + return; + + default: UHD_THROW_PROP_GET_ERROR(); + } +} + +/*********************************************************************** + * TX Dboard Set + **********************************************************************/ +void usrp_e100_impl::tx_dboard_set(const wax::obj &key, const wax::obj &val){ + switch(key.as<dboard_prop_t>()){ + case DBOARD_PROP_DBOARD_ID: + _tx_db_eeprom.id = val.as<dboard_id_t>(); + _iface->write_eeprom(I2C_ADDR_TX_DB, 0, _tx_db_eeprom.get_eeprom_bytes()); + return; + + default: UHD_THROW_PROP_SET_ERROR(); + } +} diff --git a/host/lib/usrp/usrp_e100/dsp_impl.cpp b/host/lib/usrp/usrp_e100/dsp_impl.cpp new file mode 100644 index 000000000..43a3bd3be --- /dev/null +++ b/host/lib/usrp/usrp_e100/dsp_impl.cpp @@ -0,0 +1,192 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include "usrp_e100_impl.hpp" +#include "usrp_e100_regs.hpp" +#include <uhd/usrp/dsp_utils.hpp> +#include <uhd/usrp/dsp_props.hpp> +#include <boost/math/special_functions/round.hpp> +#include <boost/bind.hpp> + +#define rint boost::math::iround + +using namespace uhd; +using namespace uhd::usrp; + +/*********************************************************************** + * RX DDC Initialization + **********************************************************************/ +void usrp_e100_impl::rx_ddc_init(void){ + _rx_ddc_proxy = wax_obj_proxy::make( + boost::bind(&usrp_e100_impl::rx_ddc_get, this, _1, _2), + boost::bind(&usrp_e100_impl::rx_ddc_set, this, _1, _2) + ); + + //initial config and update + rx_ddc_set(DSP_PROP_FREQ_SHIFT, double(0)); + rx_ddc_set(DSP_PROP_HOST_RATE, double(64e6/10)); +} + +/*********************************************************************** + * RX DDC Get + **********************************************************************/ +void usrp_e100_impl::rx_ddc_get(const wax::obj &key_, wax::obj &val){ + named_prop_t key = named_prop_t::extract(key_); + + switch(key.as<dsp_prop_t>()){ + case DSP_PROP_NAME: + val = std::string("usrp-e ddc0"); + return; + + case DSP_PROP_OTHERS: + val = prop_names_t(); //empty + return; + + case DSP_PROP_FREQ_SHIFT: + val = _ddc_freq; + return; + + case DSP_PROP_FREQ_SHIFT_NAMES: + val = prop_names_t(1, ""); + return; + + case DSP_PROP_CODEC_RATE: + val = _clock_ctrl->get_fpga_clock_rate(); + return; + + case DSP_PROP_HOST_RATE: + val = _clock_ctrl->get_fpga_clock_rate()/_ddc_decim; + return; + + default: UHD_THROW_PROP_GET_ERROR(); + } +} + +/*********************************************************************** + * RX DDC Set + **********************************************************************/ +void usrp_e100_impl::rx_ddc_set(const wax::obj &key_, const wax::obj &val){ + named_prop_t key = named_prop_t::extract(key_); + + switch(key.as<dsp_prop_t>()){ + + case DSP_PROP_FREQ_SHIFT:{ + double new_freq = val.as<double>(); + _iface->poke32(UE_REG_DSP_RX_FREQ, + dsp_type1::calc_cordic_word_and_update(new_freq, _clock_ctrl->get_fpga_clock_rate()) + ); + _ddc_freq = new_freq; //shadow + } + return; + + case DSP_PROP_HOST_RATE:{ + //set the decimation + _ddc_decim = rint(_clock_ctrl->get_fpga_clock_rate()/val.as<double>()); + _iface->poke32(UE_REG_DSP_RX_DECIM_RATE, dsp_type1::calc_cic_filter_word(_ddc_decim)); + + //set the scaling + static const boost::int16_t default_rx_scale_iq = 1024; + _iface->poke32(UE_REG_DSP_RX_SCALE_IQ, + dsp_type1::calc_iq_scale_word(default_rx_scale_iq, default_rx_scale_iq) + ); + } + return; + + default: UHD_THROW_PROP_SET_ERROR(); + } +} + +/*********************************************************************** + * TX DUC Initialization + **********************************************************************/ +void usrp_e100_impl::tx_duc_init(void){ + _tx_duc_proxy = wax_obj_proxy::make( + boost::bind(&usrp_e100_impl::tx_duc_get, this, _1, _2), + boost::bind(&usrp_e100_impl::tx_duc_set, this, _1, _2) + ); + + //initial config and update + tx_duc_set(DSP_PROP_FREQ_SHIFT, double(0)); + tx_duc_set(DSP_PROP_HOST_RATE, double(64e6/10)); +} + +/*********************************************************************** + * TX DUC Get + **********************************************************************/ +void usrp_e100_impl::tx_duc_get(const wax::obj &key_, wax::obj &val){ + named_prop_t key = named_prop_t::extract(key_); + + switch(key.as<dsp_prop_t>()){ + case DSP_PROP_NAME: + val = std::string("usrp-e duc0"); + return; + + case DSP_PROP_OTHERS: + val = prop_names_t(); //empty + return; + + case DSP_PROP_FREQ_SHIFT: + val = _duc_freq; + return; + + case DSP_PROP_FREQ_SHIFT_NAMES: + val = prop_names_t(1, ""); + return; + + case DSP_PROP_CODEC_RATE: + val = _clock_ctrl->get_fpga_clock_rate(); + return; + + case DSP_PROP_HOST_RATE: + val = _clock_ctrl->get_fpga_clock_rate()/_duc_interp; + return; + + default: UHD_THROW_PROP_GET_ERROR(); + } +} + +/*********************************************************************** + * TX DUC Set + **********************************************************************/ +void usrp_e100_impl::tx_duc_set(const wax::obj &key_, const wax::obj &val){ + named_prop_t key = named_prop_t::extract(key_); + + switch(key.as<dsp_prop_t>()){ + + case DSP_PROP_FREQ_SHIFT:{ + double new_freq = val.as<double>(); + _iface->poke32(UE_REG_DSP_TX_FREQ, + dsp_type1::calc_cordic_word_and_update(new_freq, _clock_ctrl->get_fpga_clock_rate()) + ); + _duc_freq = new_freq; //shadow + } + return; + + case DSP_PROP_HOST_RATE:{ + _duc_interp = rint(_clock_ctrl->get_fpga_clock_rate()/val.as<double>()); + + //set the interpolation + _iface->poke32(UE_REG_DSP_TX_INTERP_RATE, dsp_type1::calc_cic_filter_word(_duc_interp)); + + //set the scaling + _iface->poke32(UE_REG_DSP_TX_SCALE_IQ, dsp_type1::calc_iq_scale_word(_duc_interp)); + } + return; + + default: UHD_THROW_PROP_SET_ERROR(); + } +} diff --git a/host/lib/usrp/usrp_e100/fpga-downloader.cc b/host/lib/usrp/usrp_e100/fpga-downloader.cc new file mode 100644 index 000000000..4a3d3b9af --- /dev/null +++ b/host/lib/usrp/usrp_e100/fpga-downloader.cc @@ -0,0 +1,274 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include <uhd/config.hpp> +#include <uhd/utils/assert.hpp> + +#include <iostream> +#include <sstream> +#include <fstream> +#include <string> +#include <cstdlib> +#include <stdexcept> + +#include <fcntl.h> +#include <sys/types.h> +#include <sys/stat.h> +#include <sys/ioctl.h> + +#include <linux/spi/spidev.h> + +/* + * Configuration connections + * + * CCK - MCSPI1_CLK + * DIN - MCSPI1_MOSI + * PROG_B - GPIO_175 - output (change mux) + * DONE - GPIO_173 - input (change mux) + * INIT_B - GPIO_114 - input (change mux) + * +*/ + +const unsigned int PROG_B = 175; +const unsigned int DONE = 173; +const unsigned int INIT_B = 114; + +//static std::string bit_file = "safe_u1e.bin"; + +const int BUF_SIZE = 4096; + +enum gpio_direction {IN, OUT}; + +class gpio { + public: + + gpio(unsigned int gpio_num, gpio_direction pin_direction); + + bool get_value(); + void set_value(bool state); + + private: + + std::stringstream base_path; + std::fstream value_file; +}; + +class spidev { + public: + + spidev(std::string dev_name); + ~spidev(); + + void send(char *wbuf, char *rbuf, unsigned int nbytes); + + private: + + int fd; + +}; + +gpio::gpio(unsigned int gpio_num, gpio_direction pin_direction) +{ + std::fstream export_file; + + export_file.open("/sys/class/gpio/export", std::ios::out); + if (not export_file.is_open()) throw std::runtime_error( + "Failed to open gpio export file." + ); + + export_file << gpio_num << std::endl; + + base_path << "/sys/class/gpio/gpio" << gpio_num << std::flush; + + std::fstream direction_file; + std::string direction_file_name; + + if (gpio_num != 114) { + direction_file_name = base_path.str() + "/direction"; + + direction_file.open(direction_file_name.c_str()); + if (!direction_file.is_open()) + std::cout << "Failed to open direction file." << std::endl; + if (pin_direction == OUT) + direction_file << "out" << std::endl; + else + direction_file << "in" << std::endl; + } + + std::string value_file_name; + + value_file_name = base_path.str() + "/value"; + + value_file.open(value_file_name.c_str(), std::ios_base::in | std::ios_base::out); + if (!value_file.is_open()) + std::cout << "Failed to open value file." << std::endl; +} + +bool gpio::get_value() +{ + + std::string val; + + std::getline(value_file, val); + value_file.seekg(0); + + if (val == "0") + return false; + else if (val == "1") + return true; + else + std::cout << "Data read from value file|" << val << "|" << std::endl; + + return false; +} + +void gpio::set_value(bool state) +{ + + if (state) + value_file << "1" << std::endl; + else + value_file << "0" << std::endl; +} + +static void prepare_fpga_for_configuration(gpio &prog, gpio &)//init) +{ + + prog.set_value(true); + prog.set_value(false); + prog.set_value(true); + +#if 0 + bool ready_to_program(false); + unsigned int count(0); + do { + ready_to_program = init.get_value(); + count++; + + sleep(1); + } while (count < 10 && !ready_to_program); + + if (count == 10) { + std::cout << "FPGA not ready for programming." << std::endl; + exit(-1); + } +#endif +} + +spidev::spidev(std::string fname) +{ + int ret; + int mode = 0; + int speed = 12000000; + int bits = 8; + + fd = open(fname.c_str(), O_RDWR); + + ret = ioctl(fd, SPI_IOC_WR_MODE, &mode); + ret = ioctl(fd, SPI_IOC_WR_MAX_SPEED_HZ, &speed); + ret = ioctl(fd, SPI_IOC_WR_BITS_PER_WORD, &bits); +} + + +spidev::~spidev() +{ + close(fd); +} + +void spidev::send(char *buf, char *rbuf, unsigned int nbytes) +{ + int ret; + + struct spi_ioc_transfer tr; + tr.tx_buf = (unsigned long) buf; + tr.rx_buf = (unsigned long) rbuf; + tr.len = nbytes; + tr.delay_usecs = 0; + tr.speed_hz = 48000000; + tr.bits_per_word = 8; + + ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr); + +} + +static void send_file_to_fpga(const std::string &file_name, gpio &error, gpio &done) +{ + std::ifstream bitstream; + + std::cout << "File name - " << file_name.c_str() << std::endl; + + bitstream.open(file_name.c_str(), std::ios::binary); + if (!bitstream.is_open()) + std::cout << "File " << file_name << " not opened succesfully." << std::endl; + + spidev spi("/dev/spidev1.0"); + char buf[BUF_SIZE]; + char rbuf[BUF_SIZE]; + + do { + bitstream.read(buf, BUF_SIZE); + spi.send(buf, rbuf, bitstream.gcount()); + + if (error.get_value()) + std::cout << "INIT_B went high, error occured." << std::endl; + + if (!done.get_value()) + std::cout << "Configuration complete." << std::endl; + + } while (bitstream.gcount() == BUF_SIZE); +} + +/* +int main(int argc, char *argv[]) +{ + + gpio gpio_prog_b(PROG_B, OUT); + gpio gpio_init_b(INIT_B, IN); + gpio gpio_done (DONE, IN); + + if (argc == 2) + bit_file = argv[1]; + + std::cout << "FPGA config file: " << bit_file << std::endl; + + prepare_fpga_for_configuration(gpio_prog_b, gpio_init_b); + + std::cout << "Done = " << gpio_done.get_value() << std::endl; + + send_file_to_fpga(bit_file, gpio_init_b, gpio_done); +} +*/ + +void usrp_e100_load_fpga(const std::string &bin_file){ + gpio gpio_prog_b(PROG_B, OUT); + gpio gpio_init_b(INIT_B, IN); + gpio gpio_done (DONE, IN); + + std::cout << "Loading FPGA image: " << bin_file << "... " << std::flush; + + UHD_ASSERT_THROW(std::system("/sbin/rmmod usrp_e") == 0); + + prepare_fpga_for_configuration(gpio_prog_b, gpio_init_b); + + std::cout << "done = " << gpio_done.get_value() << std::endl; + + send_file_to_fpga(bin_file, gpio_init_b, gpio_done); + + UHD_ASSERT_THROW(std::system("/sbin/modprobe usrp_e") == 0); + +} + diff --git a/host/lib/usrp/usrp_e100/include/linux/usrp_e.h b/host/lib/usrp/usrp_e100/include/linux/usrp_e.h new file mode 100644 index 000000000..4c6a5dd89 --- /dev/null +++ b/host/lib/usrp/usrp_e100/include/linux/usrp_e.h @@ -0,0 +1,91 @@ + +/* + * Copyright (C) 2010 Ettus Research, LLC + * + * Written by Philip Balister <philip@opensdr.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __USRP_E_H +#define __USRP_E_H + +#include <linux/types.h> +#include <linux/ioctl.h> + +struct usrp_e_ctl16 { + __u32 offset; + __u32 count; + __u16 buf[20]; +}; + +struct usrp_e_ctl32 { + __u32 offset; + __u32 count; + __u32 buf[10]; +}; + +/* SPI interface */ + +#define UE_SPI_TXONLY 0 +#define UE_SPI_TXRX 1 + +/* Defines for spi ctrl register */ +#define UE_SPI_CTRL_TXNEG (1<<10) +#define UE_SPI_CTRL_RXNEG (1<<9) + +#define UE_SPI_PUSH_RISE 0 +#define UE_SPI_PUSH_FALL UE_SPI_CTRL_TXNEG +#define UE_SPI_LATCH_RISE 0 +#define UE_SPI_LATCH_FALL UE_SPI_CTRL_RXNEG + +struct usrp_e_spi { + __u8 readback; + __u32 slave; + __u32 data; + __u32 length; + __u32 flags; +}; + +struct usrp_e_i2c { + __u8 addr; + __u32 len; + __u8 data[]; +}; + +#define USRP_E_IOC_MAGIC 'u' +#define USRP_E_WRITE_CTL16 _IOW(USRP_E_IOC_MAGIC, 0x20, struct usrp_e_ctl16) +#define USRP_E_READ_CTL16 _IOWR(USRP_E_IOC_MAGIC, 0x21, struct usrp_e_ctl16) +#define USRP_E_WRITE_CTL32 _IOW(USRP_E_IOC_MAGIC, 0x22, struct usrp_e_ctl32) +#define USRP_E_READ_CTL32 _IOWR(USRP_E_IOC_MAGIC, 0x23, struct usrp_e_ctl32) +#define USRP_E_SPI _IOWR(USRP_E_IOC_MAGIC, 0x24, struct usrp_e_spi) +#define USRP_E_I2C_READ _IOWR(USRP_E_IOC_MAGIC, 0x25, struct usrp_e_i2c) +#define USRP_E_I2C_WRITE _IOW(USRP_E_IOC_MAGIC, 0x26, struct usrp_e_i2c) +#define USRP_E_GET_RB_INFO _IOR(USRP_E_IOC_MAGIC, 0x27, struct usrp_e_ring_buffer_size_t) +#define USRP_E_GET_COMPAT_NUMBER _IO(USRP_E_IOC_MAGIC, 0x28) + +#define USRP_E_COMPAT_NUMBER 1 + +/* Flag defines */ +#define RB_USER (1<<0) +#define RB_KERNEL (1<<1) +#define RB_OVERRUN (1<<2) +#define RB_DMA_ACTIVE (1<<3) +#define RB_USER_PROCESS (1<<4) + +struct ring_buffer_info { + int flags; + int len; +}; + +struct usrp_e_ring_buffer_size_t { + int num_pages_rx_flags; + int num_rx_frames; + int num_pages_tx_flags; + int num_tx_frames; +}; + +#endif diff --git a/host/lib/usrp/usrp_e100/io_impl.cpp b/host/lib/usrp/usrp_e100/io_impl.cpp new file mode 100644 index 000000000..7cb3e25e5 --- /dev/null +++ b/host/lib/usrp/usrp_e100/io_impl.cpp @@ -0,0 +1,272 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include "usrp_e100_impl.hpp" +#include "usrp_e100_regs.hpp" +#include <uhd/usrp/dsp_utils.hpp> +#include <uhd/utils/thread_priority.hpp> +#include <uhd/transport/bounded_buffer.hpp> +#include "../../transport/vrt_packet_handler.hpp" +#include <boost/bind.hpp> +#include <boost/format.hpp> +#include <boost/thread.hpp> +#include <iostream> + +using namespace uhd; +using namespace uhd::usrp; +using namespace uhd::transport; + +zero_copy_if::sptr usrp_e100_make_mmap_zero_copy(usrp_e100_iface::sptr iface); + +/*********************************************************************** + * Constants + **********************************************************************/ +static const size_t tx_async_report_sid = 1; +static const int underflow_flags = async_metadata_t::EVENT_CODE_UNDERFLOW | async_metadata_t::EVENT_CODE_UNDERFLOW_IN_PACKET; +static const bool recv_debug = false; + +/*********************************************************************** + * io impl details (internal to this file) + * - pirate crew of 1 + * - bounded buffer + * - thread loop + * - vrt packet handler states + **********************************************************************/ +struct usrp_e100_impl::io_impl{ + //state management for the vrt packet handler code + vrt_packet_handler::recv_state packet_handler_recv_state; + vrt_packet_handler::send_state packet_handler_send_state; + zero_copy_if::sptr data_xport; + bool continuous_streaming; + io_impl(usrp_e100_iface::sptr iface): + data_xport(usrp_e100_make_mmap_zero_copy(iface)), + recv_pirate_booty(recv_booty_type::make(data_xport->get_num_recv_frames())), + async_msg_fifo(bounded_buffer<async_metadata_t>::make(100/*messages deep*/)) + { + /* NOP */ + } + + ~io_impl(void){ + recv_pirate_crew_raiding = false; + recv_pirate_crew.interrupt_all(); + recv_pirate_crew.join_all(); + } + + bool get_recv_buffs(vrt_packet_handler::managed_recv_buffs_t &buffs, double timeout){ + UHD_ASSERT_THROW(buffs.size() == 1); + boost::this_thread::disable_interruption di; //disable because the wait can throw + return recv_pirate_booty->pop_with_timed_wait(buffs.front(), timeout); + } + + //a pirate's life is the life for me! + void recv_pirate_loop(usrp_e100_clock_ctrl::sptr); + typedef bounded_buffer<managed_recv_buffer::sptr> recv_booty_type; + recv_booty_type::sptr recv_pirate_booty; + bounded_buffer<async_metadata_t>::sptr async_msg_fifo; + boost::thread_group recv_pirate_crew; + bool recv_pirate_crew_raiding; +}; + +/*********************************************************************** + * Receive Pirate Loop + * - while raiding, loot for recv buffers + * - put booty into the alignment buffer + **********************************************************************/ +void usrp_e100_impl::io_impl::recv_pirate_loop(usrp_e100_clock_ctrl::sptr clock_ctrl) +{ + set_thread_priority_safe(); + recv_pirate_crew_raiding = true; + + while(recv_pirate_crew_raiding){ + managed_recv_buffer::sptr buff = this->data_xport->get_recv_buff(); + if (not buff.get()) continue; //ignore timeout/error buffers + + if (recv_debug){ + std::cout << "len " << buff->size() << std::endl; + for (size_t i = 0; i < 9; i++){ + std::cout << boost::format(" 0x%08x") % buff->cast<const boost::uint32_t *>()[i] << std::endl; + } + std::cout << std::endl << std::endl; + } + + try{ + //extract the vrt header packet info + vrt::if_packet_info_t if_packet_info; + if_packet_info.num_packet_words32 = buff->size()/sizeof(boost::uint32_t); + const boost::uint32_t *vrt_hdr = buff->cast<const boost::uint32_t *>(); + vrt::if_hdr_unpack_le(vrt_hdr, if_packet_info); + + //handle a tx async report message + if (if_packet_info.sid == tx_async_report_sid and if_packet_info.packet_type != vrt::if_packet_info_t::PACKET_TYPE_DATA){ + + //fill in the async metadata + async_metadata_t metadata; + metadata.channel = 0; + metadata.has_time_spec = if_packet_info.has_tsi and if_packet_info.has_tsf; + metadata.time_spec = time_spec_t( + time_t(if_packet_info.tsi), size_t(if_packet_info.tsf), clock_ctrl->get_fpga_clock_rate() + ); + metadata.event_code = vrt_packet_handler::get_context_code<async_metadata_t::event_code_t>(vrt_hdr, if_packet_info); + + //print the famous U, and push the metadata into the message queue + if (metadata.event_code & underflow_flags) std::cerr << "U" << std::flush; + async_msg_fifo->push_with_pop_on_full(metadata); + continue; + } + + //same number of frames as the data transport -> always immediate + recv_pirate_booty->push_with_wait(buff); + + }catch(const std::exception &e){ + std::cerr << "Error (usrp-e recv pirate loop): " << e.what() << std::endl; + } + } +} + +/*********************************************************************** + * Helper Functions + **********************************************************************/ +void usrp_e100_impl::io_init(void){ + //setup otw types + _send_otw_type.width = 16; + _send_otw_type.shift = 0; + _send_otw_type.byteorder = otw_type_t::BO_LITTLE_ENDIAN; + + _recv_otw_type.width = 16; + _recv_otw_type.shift = 0; + _recv_otw_type.byteorder = otw_type_t::BO_LITTLE_ENDIAN; + + //setup before the registers (transport called to calculate max spp) + _io_impl = UHD_PIMPL_MAKE(io_impl, (_iface)); + + //setup rx data path + _iface->poke32(UE_REG_CTRL_RX_NSAMPS_PER_PKT, get_max_recv_samps_per_packet()); + _iface->poke32(UE_REG_CTRL_RX_NCHANNELS, 1); + _iface->poke32(UE_REG_CTRL_RX_CLEAR_OVERRUN, 1); //reset + _iface->poke32(UE_REG_CTRL_RX_VRT_HEADER, 0 + | (0x1 << 28) //if data with stream id + | (0x1 << 26) //has trailer + | (0x3 << 22) //integer time other + | (0x1 << 20) //fractional time sample count + ); + _iface->poke32(UE_REG_CTRL_RX_VRT_STREAM_ID, 0); + _iface->poke32(UE_REG_CTRL_RX_VRT_TRAILER, 0); + + //setup the tx policy + _iface->poke32(UE_REG_CTRL_TX_REPORT_SID, tx_async_report_sid); + _iface->poke32(UE_REG_CTRL_TX_POLICY, UE_FLAG_CTRL_TX_POLICY_NEXT_PACKET); + + //spawn a pirate, yarrr! + _io_impl->recv_pirate_crew.create_thread(boost::bind( + &usrp_e100_impl::io_impl::recv_pirate_loop, _io_impl.get(), _clock_ctrl + )); +} + +void usrp_e100_impl::issue_stream_cmd(const stream_cmd_t &stream_cmd){ + _io_impl->continuous_streaming = (stream_cmd.stream_mode == stream_cmd_t::STREAM_MODE_START_CONTINUOUS); + _iface->poke32(UE_REG_CTRL_RX_STREAM_CMD, dsp_type1::calc_stream_cmd_word( + stream_cmd, get_max_recv_samps_per_packet() + )); + _iface->poke32(UE_REG_CTRL_RX_TIME_SECS, boost::uint32_t(stream_cmd.time_spec.get_full_secs())); + _iface->poke32(UE_REG_CTRL_RX_TIME_TICKS, stream_cmd.time_spec.get_tick_count(_clock_ctrl->get_fpga_clock_rate())); +} + +void usrp_e100_impl::handle_overrun(size_t){ + std::cerr << "O"; //the famous OOOOOOOOOOO + _iface->poke32(UE_REG_CTRL_RX_CLEAR_OVERRUN, 0); + if (_io_impl->continuous_streaming){ + this->issue_stream_cmd(stream_cmd_t::STREAM_MODE_START_CONTINUOUS); + } +} + +/*********************************************************************** + * Data Send + **********************************************************************/ +bool get_send_buffs( + zero_copy_if::sptr trans, double timeout, + vrt_packet_handler::managed_send_buffs_t &buffs +){ + UHD_ASSERT_THROW(buffs.size() == 1); + buffs[0] = trans->get_send_buff(timeout); + return buffs[0].get() != NULL; +} + +size_t usrp_e100_impl::get_max_send_samps_per_packet(void) const{ + static const size_t hdr_size = 0 + + vrt::max_if_hdr_words32*sizeof(boost::uint32_t) + - sizeof(vrt::if_packet_info_t().cid) //no class id ever used + ; + size_t bpp = _io_impl->data_xport->get_send_frame_size() - hdr_size; + return bpp/_send_otw_type.get_sample_size(); +} + +size_t usrp_e100_impl::send( + const std::vector<const void *> &buffs, size_t num_samps, + const tx_metadata_t &metadata, const io_type_t &io_type, + send_mode_t send_mode, double timeout +){ + return vrt_packet_handler::send( + _io_impl->packet_handler_send_state, //last state of the send handler + buffs, num_samps, //buffer to fill + metadata, send_mode, //samples metadata + io_type, _send_otw_type, //input and output types to convert + _clock_ctrl->get_fpga_clock_rate(), //master clock tick rate + uhd::transport::vrt::if_hdr_pack_le, + boost::bind(&get_send_buffs, _io_impl->data_xport, timeout, _1), + get_max_send_samps_per_packet() + ); +} + +/*********************************************************************** + * Data Recv + **********************************************************************/ +size_t usrp_e100_impl::get_max_recv_samps_per_packet(void) const{ + static const size_t hdr_size = 0 + + vrt::max_if_hdr_words32*sizeof(boost::uint32_t) + + sizeof(vrt::if_packet_info_t().tlr) //forced to have trailer + - sizeof(vrt::if_packet_info_t().cid) //no class id ever used + ; + size_t bpp = _io_impl->data_xport->get_recv_frame_size() - hdr_size; + return bpp/_recv_otw_type.get_sample_size(); +} + +size_t usrp_e100_impl::recv( + const std::vector<void *> &buffs, size_t num_samps, + rx_metadata_t &metadata, const io_type_t &io_type, + recv_mode_t recv_mode, double timeout +){ + return vrt_packet_handler::recv( + _io_impl->packet_handler_recv_state, //last state of the recv handler + buffs, num_samps, //buffer to fill + metadata, recv_mode, //samples metadata + io_type, _recv_otw_type, //input and output types to convert + _clock_ctrl->get_fpga_clock_rate(), //master clock tick rate + uhd::transport::vrt::if_hdr_unpack_le, + boost::bind(&usrp_e100_impl::io_impl::get_recv_buffs, _io_impl.get(), _1, timeout), + boost::bind(&usrp_e100_impl::handle_overrun, this, _1) + ); +} + +/*********************************************************************** + * Async Recv + **********************************************************************/ +bool usrp_e100_impl::recv_async_msg( + async_metadata_t &async_metadata, double timeout +){ + boost::this_thread::disable_interruption di; //disable because the wait can throw + return _io_impl->async_msg_fifo->pop_with_timed_wait(async_metadata, timeout); +} diff --git a/host/lib/usrp/usrp_e100/mboard_impl.cpp b/host/lib/usrp/usrp_e100/mboard_impl.cpp new file mode 100644 index 000000000..03c4385aa --- /dev/null +++ b/host/lib/usrp/usrp_e100/mboard_impl.cpp @@ -0,0 +1,198 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include "usrp_e100_impl.hpp" +#include "usrp_e100_regs.hpp" +#include <uhd/usrp/dsp_utils.hpp> +#include <uhd/usrp/misc_utils.hpp> +#include <uhd/utils/assert.hpp> +#include <uhd/usrp/mboard_props.hpp> +#include <boost/bind.hpp> +#include <iostream> + +using namespace uhd; +using namespace uhd::usrp; + +/*********************************************************************** + * Mboard Initialization + **********************************************************************/ +void usrp_e100_impl::mboard_init(void){ + _mboard_proxy = wax_obj_proxy::make( + boost::bind(&usrp_e100_impl::mboard_get, this, _1, _2), + boost::bind(&usrp_e100_impl::mboard_set, this, _1, _2) + ); + + //init the clock config + _clock_config.ref_source = clock_config_t::REF_AUTO; + _clock_config.pps_source = clock_config_t::PPS_SMA; + _clock_config.pps_polarity = clock_config_t::PPS_NEG; + + update_clock_config(); +} + +void usrp_e100_impl::update_clock_config(void){ + boost::uint32_t pps_flags = 0; + + //translate pps polarity enums + switch(_clock_config.pps_polarity){ + case clock_config_t::PPS_POS: pps_flags |= UE_FLAG_TIME64_PPS_POSEDGE; break; + case clock_config_t::PPS_NEG: pps_flags |= UE_FLAG_TIME64_PPS_NEGEDGE; break; + default: throw std::runtime_error("unhandled clock configuration pps polarity"); + } + + //set the pps flags + _iface->poke32(UE_REG_TIME64_FLAGS, pps_flags); + + //clock source ref 10mhz + switch(_clock_config.ref_source){ + case clock_config_t::REF_AUTO: _clock_ctrl->use_auto_ref(); + case clock_config_t::REF_INT: _clock_ctrl->use_internal_ref(); + case clock_config_t::REF_SMA: _clock_ctrl->use_external_ref(); + default: throw std::runtime_error("unhandled clock configuration ref source"); + } +} + +/*********************************************************************** + * Mboard Get + **********************************************************************/ +void usrp_e100_impl::mboard_get(const wax::obj &key_, wax::obj &val){ + named_prop_t key = named_prop_t::extract(key_); + + //handle the get request conditioned on the key + switch(key.as<mboard_prop_t>()){ + case MBOARD_PROP_NAME: + val = std::string("usrp-e mboard"); + return; + + case MBOARD_PROP_OTHERS: + val = prop_names_t(); + return; + + case MBOARD_PROP_RX_DBOARD: + UHD_ASSERT_THROW(key.name == ""); + val = _rx_dboard_proxy->get_link(); + return; + + case MBOARD_PROP_RX_DBOARD_NAMES: + val = prop_names_t(1, ""); //vector of size 1 with empty string + return; + + case MBOARD_PROP_TX_DBOARD: + UHD_ASSERT_THROW(key.name == ""); + val = _tx_dboard_proxy->get_link(); + return; + + case MBOARD_PROP_TX_DBOARD_NAMES: + val = prop_names_t(1, ""); //vector of size 1 with empty string + return; + + case MBOARD_PROP_RX_DSP: + UHD_ASSERT_THROW(key.name == ""); + val = _rx_ddc_proxy->get_link(); + return; + + case MBOARD_PROP_RX_DSP_NAMES: + val = prop_names_t(1, ""); + return; + + case MBOARD_PROP_TX_DSP: + UHD_ASSERT_THROW(key.name == ""); + val = _tx_duc_proxy->get_link(); + return; + + case MBOARD_PROP_TX_DSP_NAMES: + val = prop_names_t(1, ""); + return; + + case MBOARD_PROP_CLOCK_CONFIG: + val = _clock_config; + return; + + case MBOARD_PROP_RX_SUBDEV_SPEC: + val = _rx_subdev_spec; + return; + + case MBOARD_PROP_TX_SUBDEV_SPEC: + val = _tx_subdev_spec; + return; + + case MBOARD_PROP_EEPROM_MAP: + val = _iface->mb_eeprom; + return; + + default: UHD_THROW_PROP_GET_ERROR(); + } +} + +/*********************************************************************** + * Mboard Set + **********************************************************************/ +void usrp_e100_impl::mboard_set(const wax::obj &key, const wax::obj &val){ + //handle the get request conditioned on the key + switch(key.as<mboard_prop_t>()){ + + case MBOARD_PROP_STREAM_CMD: + issue_stream_cmd(val.as<stream_cmd_t>()); + return; + + case MBOARD_PROP_TIME_NOW: + case MBOARD_PROP_TIME_NEXT_PPS:{ + time_spec_t time_spec = val.as<time_spec_t>(); + _iface->poke32(UE_REG_TIME64_TICKS, time_spec.get_tick_count(_clock_ctrl->get_fpga_clock_rate())); + boost::uint32_t imm_flags = (key.as<mboard_prop_t>() == MBOARD_PROP_TIME_NOW)? 1 : 0; + _iface->poke32(UE_REG_TIME64_IMM, imm_flags); + _iface->poke32(UE_REG_TIME64_SECS, time_spec.get_full_secs()); + } + return; + + case MBOARD_PROP_RX_SUBDEV_SPEC: + _rx_subdev_spec = val.as<subdev_spec_t>(); + verify_rx_subdev_spec(_rx_subdev_spec, _mboard_proxy->get_link()); + //sanity check + UHD_ASSERT_THROW(_rx_subdev_spec.size() == 1); + //set the mux + _iface->poke32(UE_REG_DSP_RX_MUX, dsp_type1::calc_rx_mux_word( + _dboard_manager->get_rx_subdev(_rx_subdev_spec.front().sd_name)[SUBDEV_PROP_CONNECTION].as<subdev_conn_t>() + )); + return; + + case MBOARD_PROP_TX_SUBDEV_SPEC: + _tx_subdev_spec = val.as<subdev_spec_t>(); + verify_tx_subdev_spec(_tx_subdev_spec, _mboard_proxy->get_link()); + //sanity check + UHD_ASSERT_THROW(_tx_subdev_spec.size() == 1); + //set the mux + _iface->poke32(UE_REG_DSP_TX_MUX, dsp_type1::calc_tx_mux_word( + _dboard_manager->get_tx_subdev(_tx_subdev_spec.front().sd_name)[SUBDEV_PROP_CONNECTION].as<subdev_conn_t>() + )); + return; + + case MBOARD_PROP_EEPROM_MAP: + // Step1: commit the map, writing only those values set. + // Step2: readback the entire eeprom map into the iface. + val.as<mboard_eeprom_t>().commit(_iface->get_i2c_dev_iface(), mboard_eeprom_t::MAP_E100); + _iface->mb_eeprom = mboard_eeprom_t(_iface->get_i2c_dev_iface(), mboard_eeprom_t::MAP_E100); + return; + + case MBOARD_PROP_CLOCK_CONFIG: + _clock_config = val.as<clock_config_t>(); + update_clock_config(); + return; + + default: UHD_THROW_PROP_SET_ERROR(); + } +} diff --git a/host/lib/usrp/usrp_e100/usrp_e100_iface.cpp b/host/lib/usrp/usrp_e100/usrp_e100_iface.cpp new file mode 100644 index 000000000..40c7afabb --- /dev/null +++ b/host/lib/usrp/usrp_e100/usrp_e100_iface.cpp @@ -0,0 +1,268 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include "usrp_e100_iface.hpp" +#include <uhd/utils/assert.hpp> +#include <sys/ioctl.h> //ioctl +#include <fcntl.h> //open, close +#include <linux/usrp_e.h> //ioctl structures and constants +#include <boost/format.hpp> +#include <boost/thread.hpp> //mutex +#include <linux/i2c-dev.h> +#include <linux/i2c.h> +#include <stdexcept> + +using namespace uhd; +using namespace uhd::usrp; + +/*********************************************************************** + * I2C device node implementation wrapper + **********************************************************************/ +class i2c_dev_iface : public i2c_iface{ +public: + i2c_dev_iface(const std::string &node){ + if ((_node_fd = ::open(node.c_str(), O_RDWR)) < 0){ + throw std::runtime_error("Failed to open " + node); + } + } + + ~i2c_dev_iface(void){ + ::close(_node_fd); + } + + void write_i2c(boost::uint8_t addr, const byte_vector_t &bytes){ + byte_vector_t rw_bytes(bytes); + + //setup the message + i2c_msg msg; + msg.addr = addr; + msg.flags = 0; + msg.len = bytes.size(); + msg.buf = &rw_bytes.front(); + + //setup the data + i2c_rdwr_ioctl_data data; + data.msgs = &msg; + data.nmsgs = 1; + + //call the ioctl + UHD_ASSERT_THROW(::ioctl(_node_fd, I2C_RDWR, &data) >= 0); + } + + byte_vector_t read_i2c(boost::uint8_t addr, size_t num_bytes){ + byte_vector_t bytes(num_bytes); + + //setup the message + i2c_msg msg; + msg.addr = addr; + msg.flags = I2C_M_RD; + msg.len = bytes.size(); + msg.buf = &bytes.front(); + + //setup the data + i2c_rdwr_ioctl_data data; + data.msgs = &msg; + data.nmsgs = 1; + + //call the ioctl + UHD_ASSERT_THROW(::ioctl(_node_fd, I2C_RDWR, &data) >= 0); + + return bytes; + } + +private: int _node_fd; +}; + +/*********************************************************************** + * USRP-E100 interface implementation + **********************************************************************/ +class usrp_e100_iface_impl : public usrp_e100_iface{ +public: + + int get_file_descriptor(void){ + return _node_fd; + } + + /******************************************************************* + * Structors + ******************************************************************/ + usrp_e100_iface_impl(const std::string &node): + _i2c_dev_iface(i2c_dev_iface("/dev/i2c-3")) + { + //open the device node and check file descriptor + if ((_node_fd = ::open(node.c_str(), O_RDWR)) < 0){ + throw std::runtime_error("Failed to open " + node); + } + + mb_eeprom = mboard_eeprom_t(get_i2c_dev_iface(), mboard_eeprom_t::MAP_E100); + } + + ~usrp_e100_iface_impl(void){ + //close the device node file descriptor + ::close(_node_fd); + } + + /******************************************************************* + * IOCTL: provides the communication base for all other calls + ******************************************************************/ + void ioctl(int request, void *mem){ + boost::mutex::scoped_lock lock(_ctrl_mutex); + + if (::ioctl(_node_fd, request, mem) < 0){ + throw std::runtime_error(str( + boost::format("ioctl failed with request %d") % request + )); + } + } + + /******************************************************************* + * I2C device node interface + ******************************************************************/ + i2c_iface &get_i2c_dev_iface(void){ + return _i2c_dev_iface; + } + + /******************************************************************* + * Peek and Poke + ******************************************************************/ + void poke32(boost::uint32_t addr, boost::uint32_t value){ + //load the data struct + usrp_e_ctl32 data; + data.offset = addr; + data.count = 1; + data.buf[0] = value; + + //call the ioctl + this->ioctl(USRP_E_WRITE_CTL32, &data); + } + + void poke16(boost::uint32_t addr, boost::uint16_t value){ + //load the data struct + usrp_e_ctl16 data; + data.offset = addr; + data.count = 1; + data.buf[0] = value; + + //call the ioctl + this->ioctl(USRP_E_WRITE_CTL16, &data); + } + + boost::uint32_t peek32(boost::uint32_t addr){ + //load the data struct + usrp_e_ctl32 data; + data.offset = addr; + data.count = 1; + + //call the ioctl + this->ioctl(USRP_E_READ_CTL32, &data); + + return data.buf[0]; + } + + boost::uint16_t peek16(boost::uint32_t addr){ + //load the data struct + usrp_e_ctl16 data; + data.offset = addr; + data.count = 1; + + //call the ioctl + this->ioctl(USRP_E_READ_CTL16, &data); + + return data.buf[0]; + } + + /******************************************************************* + * I2C + ******************************************************************/ + static const size_t max_i2c_data_bytes = 10; + + void write_i2c(boost::uint8_t addr, const byte_vector_t &bytes){ + //allocate some memory for this transaction + UHD_ASSERT_THROW(bytes.size() <= max_i2c_data_bytes); + boost::uint8_t mem[sizeof(usrp_e_i2c) + max_i2c_data_bytes]; + + //load the data struct + usrp_e_i2c *data = reinterpret_cast<usrp_e_i2c*>(mem); + data->addr = addr; + data->len = bytes.size(); + std::copy(bytes.begin(), bytes.end(), data->data); + + //call the spi ioctl + this->ioctl(USRP_E_I2C_WRITE, data); + } + + byte_vector_t read_i2c(boost::uint8_t addr, size_t num_bytes){ + //allocate some memory for this transaction + UHD_ASSERT_THROW(num_bytes <= max_i2c_data_bytes); + boost::uint8_t mem[sizeof(usrp_e_i2c) + max_i2c_data_bytes]; + + //load the data struct + usrp_e_i2c *data = reinterpret_cast<usrp_e_i2c*>(mem); + data->addr = addr; + data->len = num_bytes; + + //call the spi ioctl + this->ioctl(USRP_E_I2C_READ, data); + + //unload the data + byte_vector_t bytes(data->len); + UHD_ASSERT_THROW(bytes.size() == num_bytes); + std::copy(data->data, data->data+bytes.size(), bytes.begin()); + return bytes; + } + + /******************************************************************* + * SPI + ******************************************************************/ + boost::uint32_t transact_spi( + int which_slave, + const spi_config_t &config, + boost::uint32_t bits, + size_t num_bits, + bool readback + ){ + //load data struct + usrp_e_spi data; + data.readback = (readback)? UE_SPI_TXRX : UE_SPI_TXONLY; + data.slave = which_slave; + data.length = num_bits; + data.data = bits; + + //load the flags + data.flags = 0; + data.flags |= (config.miso_edge == spi_config_t::EDGE_RISE)? UE_SPI_LATCH_RISE : UE_SPI_LATCH_FALL; + data.flags |= (config.mosi_edge == spi_config_t::EDGE_RISE)? UE_SPI_PUSH_FALL : UE_SPI_PUSH_RISE; + + //call the spi ioctl + this->ioctl(USRP_E_SPI, &data); + + //unload the data + return data.data; + } + +private: + int _node_fd; + i2c_dev_iface _i2c_dev_iface; + boost::mutex _ctrl_mutex; +}; + +/*********************************************************************** + * Public Make Function + **********************************************************************/ +usrp_e100_iface::sptr usrp_e100_iface::make(const std::string &node){ + return sptr(new usrp_e100_iface_impl(node)); +} diff --git a/host/lib/usrp/usrp_e100/usrp_e100_iface.hpp b/host/lib/usrp/usrp_e100/usrp_e100_iface.hpp new file mode 100644 index 000000000..12283fb52 --- /dev/null +++ b/host/lib/usrp/usrp_e100/usrp_e100_iface.hpp @@ -0,0 +1,119 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#ifndef INCLUDED_USRP_E100_IFACE_HPP +#define INCLUDED_USRP_E100_IFACE_HPP + +#include <uhd/transport/udp_simple.hpp> +#include <uhd/usrp/mboard_eeprom.hpp> +#include <uhd/types/serial.hpp> +#include <boost/shared_ptr.hpp> +#include <boost/utility.hpp> +#include <boost/cstdint.hpp> + +//////////////////////////////////////////////////////////////////////// +// I2C addresses +//////////////////////////////////////////////////////////////////////// +#define I2C_DEV_EEPROM 0x50 // 24LC02[45]: 7-bits 1010xxx +#define I2C_ADDR_MBOARD (I2C_DEV_EEPROM | 0x0) +#define I2C_ADDR_TX_DB (I2C_DEV_EEPROM | 0x4) +#define I2C_ADDR_RX_DB (I2C_DEV_EEPROM | 0x5) +//////////////////////////////////////////////////////////////////////// + +/*! + * The usrp-e interface class: + * Provides a set of functions to implementation layer. + * Including spi, peek, poke, control... + */ +class usrp_e100_iface : boost::noncopyable, public uhd::i2c_iface{ +public: + typedef boost::shared_ptr<usrp_e100_iface> sptr; + + /*! + * Make a new usrp-e interface with the control transport. + * \param node the device node name + * \return a new usrp-e interface object + */ + static sptr make(const std::string &node); + + /*! + * Get the underlying file descriptor. + * \return the file descriptor + */ + virtual int get_file_descriptor(void) = 0; + + /*! + * Perform an ioctl call on the device node file descriptor. + * This will throw when the internal ioctl call fails. + * \param request the control word + * \param mem pointer to some memory + */ + virtual void ioctl(int request, void *mem) = 0; + + //! Get the I2C interface for the I2C device node + virtual uhd::i2c_iface &get_i2c_dev_iface(void) = 0; + + /*! + * Write a register (32 bits) + * \param addr the address + * \param data the 32bit data + */ + virtual void poke32(boost::uint32_t addr, boost::uint32_t data) = 0; + + /*! + * Read a register (32 bits) + * \param addr the address + * \return the 32bit data + */ + virtual boost::uint32_t peek32(boost::uint32_t addr) = 0; + + /*! + * Write a register (16 bits) + * \param addr the address + * \param data the 16bit data + */ + virtual void poke16(boost::uint32_t addr, boost::uint16_t data) = 0; + + /*! + * Read a register (16 bits) + * \param addr the address + * \return the 16bit data + */ + virtual boost::uint16_t peek16(boost::uint32_t addr) = 0; + + /*! + * Perform an spi transaction. + * \param which_slave the slave device number + * \param config spi config args + * \param data the bits to write + * \param num_bits how many bits in data + * \param readback true to readback a value + * \return spi data if readback set + */ + virtual boost::uint32_t transact_spi( + int which_slave, + const uhd::spi_config_t &config, + boost::uint32_t data, + size_t num_bits, + bool readback + ) = 0; + + //motherboard eeprom map structure + uhd::usrp::mboard_eeprom_t mb_eeprom; +}; + +#endif /* INCLUDED_USRP_E100_IFACE_HPP */ diff --git a/host/lib/usrp/usrp_e100/usrp_e100_impl.cpp b/host/lib/usrp/usrp_e100/usrp_e100_impl.cpp new file mode 100644 index 000000000..40ea56466 --- /dev/null +++ b/host/lib/usrp/usrp_e100/usrp_e100_impl.cpp @@ -0,0 +1,212 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include "usrp_e100_impl.hpp" +#include "usrp_e100_regs.hpp" +#include <uhd/usrp/device_props.hpp> +#include <uhd/usrp/mboard_props.hpp> +#include <uhd/utils/assert.hpp> +#include <uhd/utils/static.hpp> +#include <uhd/utils/images.hpp> +#include <uhd/utils/warning.hpp> +#include <boost/format.hpp> +#include <boost/filesystem.hpp> +#include <boost/functional/hash.hpp> +#include <iostream> +#include <fstream> + +using namespace uhd; +using namespace uhd::usrp; +namespace fs = boost::filesystem; + +/*********************************************************************** + * Discovery + **********************************************************************/ +static device_addrs_t usrp_e100_find(const device_addr_t &hint){ + device_addrs_t usrp_e100_addrs; + + //return an empty list of addresses when type is set to non-usrp-e + if (hint.has_key("type") and hint["type"] != "usrp-e") return usrp_e100_addrs; + + //device node not provided, assume its 0 + if (not hint.has_key("node")){ + device_addr_t new_addr = hint; + new_addr["node"] = "/dev/usrp_e0"; + return usrp_e100_find(new_addr); + } + + //use the given device node name + if (fs::exists(hint["node"])){ + device_addr_t new_addr; + new_addr["type"] = "usrp-e"; + new_addr["node"] = fs::system_complete(fs::path(hint["node"])).file_string(); + try{ + usrp_e100_iface::sptr iface = usrp_e100_iface::make(new_addr["node"]); + new_addr["name"] = iface->mb_eeprom["name"]; + new_addr["serial"] = iface->mb_eeprom["serial"]; + if ( + (not hint.has_key("name") or hint["name"] == new_addr["name"]) and + (not hint.has_key("serial") or hint["serial"] == new_addr["serial"]) + ){ + usrp_e100_addrs.push_back(new_addr); + } + } + catch(const std::exception &e){ + uhd::warning::post( + std::string("Ignoring discovered device\n") + + e.what() + ); + } + } + + return usrp_e100_addrs; +} + +/*********************************************************************** + * Make + **********************************************************************/ +static device::sptr usrp_e100_make(const device_addr_t &device_addr){ + + //setup the main interface into fpga + std::string node = device_addr["node"]; + std::cout << boost::format("Opening USRP-E on %s") % node << std::endl; + usrp_e100_iface::sptr iface = usrp_e100_iface::make(node); + + //------------------------------------------------------------------ + //-- Handle the FPGA loading... + //-- The image can be confimed as already loaded when: + //-- 1) The compatibility number matches. + //-- 2) The hash in the hash-file matches. + //------------------------------------------------------------------ + static const char *hash_file_path = "/tmp/usrp_e100_hash"; + + //extract the fpga path for usrp-e + std::string usrp_e100_fpga_image = find_image_path( + device_addr.has_key("fpga")? device_addr["fpga"] : "usrp_e100_fpga.bin" + ); + + //calculate a hash of the fpga file + size_t fpga_hash = 0; + { + std::ifstream file(usrp_e100_fpga_image.c_str()); + if (not file.good()) throw std::runtime_error( + "cannot open fpga file for read: " + usrp_e100_fpga_image + ); + do{ + boost::hash_combine(fpga_hash, file.get()); + } while (file.good()); + file.close(); + } + + //read the compatibility number + boost::uint16_t fpga_compat_num = iface->peek16(UE_REG_MISC_COMPAT); + + //read the hash in the hash-file + size_t loaded_hash = 0; + try{std::ifstream(hash_file_path) >> loaded_hash;}catch(...){} + + //if not loaded: load the fpga image and write the hash-file + if (fpga_compat_num != USRP_E_COMPAT_NUM or loaded_hash != fpga_hash){ + iface.reset(); + usrp_e100_load_fpga(usrp_e100_fpga_image); + sleep(1); ///\todo do this better one day. + std::cout << boost::format("re-Opening USRP-E on %s") % node << std::endl; + iface = usrp_e100_iface::make(node); + try{std::ofstream(hash_file_path) << fpga_hash;}catch(...){} + } + + //check that the compatibility is correct + fpga_compat_num = iface->peek16(UE_REG_MISC_COMPAT); + if (fpga_compat_num != USRP_E_COMPAT_NUM){ + throw std::runtime_error(str(boost::format( + "Expected fpga compatibility number 0x%x, but got 0x%x:\n" + "The fpga build is not compatible with the host code build." + ) % USRP_E_COMPAT_NUM % fpga_compat_num)); + } + + return device::sptr(new usrp_e100_impl(iface)); +} + +UHD_STATIC_BLOCK(register_usrp_e100_device){ + device::register_device(&usrp_e100_find, &usrp_e100_make); +} + +/*********************************************************************** + * Structors + **********************************************************************/ +usrp_e100_impl::usrp_e100_impl(usrp_e100_iface::sptr iface): _iface(iface){ + + //setup interfaces into hardware + _clock_ctrl = usrp_e100_clock_ctrl::make(_iface); + _codec_ctrl = usrp_e100_codec_ctrl::make(_iface); + + //initialize the mboard + mboard_init(); + + //initialize the dboards + dboard_init(); + + //initialize the dsps + rx_ddc_init(); + tx_duc_init(); + + //init the codec properties + codec_init(); + + //init the io send/recv + io_init(); + + //set default subdev specs + this->mboard_set(MBOARD_PROP_RX_SUBDEV_SPEC, subdev_spec_t()); + this->mboard_set(MBOARD_PROP_TX_SUBDEV_SPEC, subdev_spec_t()); +} + +usrp_e100_impl::~usrp_e100_impl(void){ + /* NOP */ +} + +/*********************************************************************** + * Device Get + **********************************************************************/ +void usrp_e100_impl::get(const wax::obj &key_, wax::obj &val){ + named_prop_t key = named_prop_t::extract(key_); + + //handle the get request conditioned on the key + switch(key.as<device_prop_t>()){ + case DEVICE_PROP_NAME: + val = std::string("usrp-e device"); + return; + + case DEVICE_PROP_MBOARD: + UHD_ASSERT_THROW(key.name == ""); + val = _mboard_proxy->get_link(); + return; + + case DEVICE_PROP_MBOARD_NAMES: + val = prop_names_t(1, ""); //vector of size 1 with empty string + return; + + default: UHD_THROW_PROP_GET_ERROR(); + } +} + +/*********************************************************************** + * Device Set + **********************************************************************/ +void usrp_e100_impl::set(const wax::obj &, const wax::obj &){ + UHD_THROW_PROP_SET_ERROR(); +} diff --git a/host/lib/usrp/usrp_e100/usrp_e100_impl.hpp b/host/lib/usrp/usrp_e100/usrp_e100_impl.hpp new file mode 100644 index 000000000..de158ea5e --- /dev/null +++ b/host/lib/usrp/usrp_e100/usrp_e100_impl.hpp @@ -0,0 +1,167 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include "usrp_e100_iface.hpp" +#include "clock_ctrl.hpp" +#include "codec_ctrl.hpp" +#include <uhd/device.hpp> +#include <uhd/utils/pimpl.hpp> +#include <uhd/usrp/subdev_spec.hpp> +#include <uhd/usrp/dboard_eeprom.hpp> +#include <uhd/types/otw_type.hpp> +#include <uhd/types/clock_config.hpp> +#include <uhd/types/stream_cmd.hpp> +#include <uhd/usrp/dboard_manager.hpp> + +#ifndef INCLUDED_USRP_E100_IMPL_HPP +#define INCLUDED_USRP_E100_IMPL_HPP + +static const boost::uint16_t USRP_E_COMPAT_NUM = 0x02; + +//! load an fpga image from a bin file into the usrp-e fpga +extern void usrp_e100_load_fpga(const std::string &bin_file); + +/*! + * Make a usrp-e dboard interface. + * \param iface the usrp-e interface object + * \param clock the clock control interface + * \param codec the codec control interface + * \return a sptr to a new dboard interface + */ +uhd::usrp::dboard_iface::sptr make_usrp_e100_dboard_iface( + usrp_e100_iface::sptr iface, + usrp_e100_clock_ctrl::sptr clock, + usrp_e100_codec_ctrl::sptr codec +); + +/*! + * Simple wax obj proxy class: + * Provides a wax obj interface for a set and a get function. + * This allows us to create nested properties structures + * while maintaining flattened code within the implementation. + */ +class wax_obj_proxy : public wax::obj{ +public: + typedef boost::function<void(const wax::obj &, wax::obj &)> get_t; + typedef boost::function<void(const wax::obj &, const wax::obj &)> set_t; + typedef boost::shared_ptr<wax_obj_proxy> sptr; + + static sptr make(const get_t &get, const set_t &set){ + return sptr(new wax_obj_proxy(get, set)); + } + +private: + get_t _get; set_t _set; + wax_obj_proxy(const get_t &get, const set_t &set): _get(get), _set(set){}; + void get(const wax::obj &key, wax::obj &val){return _get(key, val);} + void set(const wax::obj &key, const wax::obj &val){return _set(key, val);} +}; + +/*! + * USRP-E100 implementation guts: + * The implementation details are encapsulated here. + * Handles properties on the mboard, dboard, dsps... + */ +class usrp_e100_impl : public uhd::device{ +public: + //structors + usrp_e100_impl(usrp_e100_iface::sptr); + ~usrp_e100_impl(void); + + //the io interface + size_t send(const std::vector<const void *> &, size_t, const uhd::tx_metadata_t &, const uhd::io_type_t &, send_mode_t, double); + size_t recv(const std::vector<void *> &, size_t, uhd::rx_metadata_t &, const uhd::io_type_t &, recv_mode_t, double); + bool recv_async_msg(uhd::async_metadata_t &, double); + size_t get_max_send_samps_per_packet(void) const; + size_t get_max_recv_samps_per_packet(void) const; + +private: + //interface to ioctls and file descriptor + usrp_e100_iface::sptr _iface; + + //handle io stuff + UHD_PIMPL_DECL(io_impl) _io_impl; + uhd::otw_type_t _send_otw_type, _recv_otw_type; + void io_init(void); + void issue_stream_cmd(const uhd::stream_cmd_t &stream_cmd); + void handle_overrun(size_t); + + //configuration shadows + uhd::clock_config_t _clock_config; + + //ad9522 clock control + usrp_e100_clock_ctrl::sptr _clock_ctrl; + + //ad9862 codec control + usrp_e100_codec_ctrl::sptr _codec_ctrl; + + //device functions and settings + void get(const wax::obj &, wax::obj &); + void set(const wax::obj &, const wax::obj &); + + //mboard functions and settings + void mboard_init(void); + void mboard_get(const wax::obj &, wax::obj &); + void mboard_set(const wax::obj &, const wax::obj &); + wax_obj_proxy::sptr _mboard_proxy; + uhd::usrp::subdev_spec_t _rx_subdev_spec, _tx_subdev_spec; + + //xx dboard functions and settings + void dboard_init(void); + uhd::usrp::dboard_manager::sptr _dboard_manager; + uhd::usrp::dboard_iface::sptr _dboard_iface; + + //rx dboard functions and settings + uhd::usrp::dboard_eeprom_t _rx_db_eeprom; + void rx_dboard_get(const wax::obj &, wax::obj &); + void rx_dboard_set(const wax::obj &, const wax::obj &); + wax_obj_proxy::sptr _rx_dboard_proxy; + + //tx dboard functions and settings + uhd::usrp::dboard_eeprom_t _tx_db_eeprom; + void tx_dboard_get(const wax::obj &, wax::obj &); + void tx_dboard_set(const wax::obj &, const wax::obj &); + wax_obj_proxy::sptr _tx_dboard_proxy; + + //rx ddc functions and settings + void rx_ddc_init(void); + void rx_ddc_get(const wax::obj &, wax::obj &); + void rx_ddc_set(const wax::obj &, const wax::obj &); + double _ddc_freq; size_t _ddc_decim; + wax_obj_proxy::sptr _rx_ddc_proxy; + + //tx duc functions and settings + void tx_duc_init(void); + void tx_duc_get(const wax::obj &, wax::obj &); + void tx_duc_set(const wax::obj &, const wax::obj &); + double _duc_freq; size_t _duc_interp; + wax_obj_proxy::sptr _tx_duc_proxy; + + //codec functions and settings + void codec_init(void); + void rx_codec_get(const wax::obj &, wax::obj &); + void rx_codec_set(const wax::obj &, const wax::obj &); + void tx_codec_get(const wax::obj &, wax::obj &); + void tx_codec_set(const wax::obj &, const wax::obj &); + wax_obj_proxy::sptr _rx_codec_proxy, _tx_codec_proxy; + + //clock control functions and settings + void init_clock_config(void); + void update_clock_config(void); +}; + +#endif /* INCLUDED_USRP_E100_IMPL_HPP */ diff --git a/host/lib/usrp/usrp_e100/usrp_e100_mmap_zero_copy.cpp b/host/lib/usrp/usrp_e100/usrp_e100_mmap_zero_copy.cpp new file mode 100644 index 000000000..bf378a9b1 --- /dev/null +++ b/host/lib/usrp/usrp_e100/usrp_e100_mmap_zero_copy.cpp @@ -0,0 +1,215 @@ +// +// Copyright 2010 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +#include "usrp_e100_iface.hpp" +#include <uhd/transport/zero_copy.hpp> +#include <uhd/utils/assert.hpp> +#include <linux/usrp_e.h> +#include <sys/mman.h> //mmap +#include <unistd.h> //getpagesize +#include <poll.h> //poll +#include <boost/bind.hpp> +#include <boost/enable_shared_from_this.hpp> +#include <iostream> + +using namespace uhd; +using namespace uhd::transport; + +static const bool fp_verbose = false; //fast-path verbose +static const bool sp_verbose = false; //slow-path verbose +static const size_t poll_breakout = 10; //how many poll timeouts constitute a full timeout + +/*********************************************************************** + * The zero copy interface implementation + **********************************************************************/ +class usrp_e100_mmap_zero_copy_impl : public zero_copy_if, public boost::enable_shared_from_this<usrp_e100_mmap_zero_copy_impl> { +public: + usrp_e100_mmap_zero_copy_impl(usrp_e100_iface::sptr iface): + _fd(iface->get_file_descriptor()), _recv_index(0), _send_index(0) + { + //get system sizes + iface->ioctl(USRP_E_GET_RB_INFO, &_rb_size); + size_t page_size = getpagesize(); + _frame_size = page_size/2; + + //calculate the memory size + _map_size = + (_rb_size.num_pages_rx_flags + _rb_size.num_pages_tx_flags) * page_size + + (_rb_size.num_rx_frames + _rb_size.num_tx_frames) * _frame_size; + + //print sizes summary + if (sp_verbose){ + std::cout << "page_size: " << page_size << std::endl; + std::cout << "frame_size: " << _frame_size << std::endl; + std::cout << "num_pages_rx_flags: " << _rb_size.num_pages_rx_flags << std::endl; + std::cout << "num_rx_frames: " << _rb_size.num_rx_frames << std::endl; + std::cout << "num_pages_tx_flags: " << _rb_size.num_pages_tx_flags << std::endl; + std::cout << "num_tx_frames: " << _rb_size.num_tx_frames << std::endl; + std::cout << "map_size: " << _map_size << std::endl; + } + + //call mmap to get the memory + _mapped_mem = ::mmap( + NULL, _map_size, PROT_READ | PROT_WRITE, MAP_SHARED, _fd, 0 + ); + UHD_ASSERT_THROW(_mapped_mem != MAP_FAILED); + + //calculate the memory offsets for info and buffers + size_t recv_info_off = 0; + size_t recv_buff_off = recv_info_off + (_rb_size.num_pages_rx_flags * page_size); + size_t send_info_off = recv_buff_off + (_rb_size.num_rx_frames * _frame_size); + size_t send_buff_off = send_info_off + (_rb_size.num_pages_tx_flags * page_size); + + //print offset summary + if (sp_verbose){ + std::cout << "recv_info_off: " << recv_info_off << std::endl; + std::cout << "recv_buff_off: " << recv_buff_off << std::endl; + std::cout << "send_info_off: " << send_info_off << std::endl; + std::cout << "send_buff_off: " << send_buff_off << std::endl; + } + + //set the internal pointers for info and buffers + typedef ring_buffer_info (*rbi_pta)[]; + char *rb_ptr = reinterpret_cast<char *>(_mapped_mem); + _recv_info = reinterpret_cast<rbi_pta>(rb_ptr + recv_info_off); + _recv_buff = rb_ptr + recv_buff_off; + _send_info = reinterpret_cast<rbi_pta>(rb_ptr + send_info_off); + _send_buff = rb_ptr + send_buff_off; + } + + ~usrp_e100_mmap_zero_copy_impl(void){ + if (sp_verbose) std::cout << "cleanup: munmap" << std::endl; + ::munmap(_mapped_mem, _map_size); + } + + managed_recv_buffer::sptr get_recv_buff(double timeout){ + if (fp_verbose) std::cout << "get_recv_buff: " << _recv_index << std::endl; + + //grab pointers to the info and buffer + ring_buffer_info *info = (*_recv_info) + _recv_index; + void *mem = _recv_buff + _frame_size*_recv_index; + + //poll/wait for a ready frame + if (not (info->flags & RB_USER)){ + for (size_t i = 0; i < poll_breakout; i++){ + pollfd pfd; + pfd.fd = _fd; + pfd.events = POLLIN; + ssize_t poll_ret = ::poll(&pfd, 1, size_t(timeout*1e3/poll_breakout)); + if (fp_verbose) std::cout << " POLLIN: " << poll_ret << std::endl; + if (poll_ret > 0) goto found_user_frame; //good poll, continue on + } + return managed_recv_buffer::sptr(); //timed-out for real + } found_user_frame: + + //the process has claimed the frame + info->flags = RB_USER_PROCESS; + + //increment the index for the next call + if (++_recv_index == size_t(_rb_size.num_rx_frames)) _recv_index = 0; + + //return the managed buffer for this frame + if (fp_verbose) std::cout << " make_recv_buff: " << info->len << std::endl; + return managed_recv_buffer::make_safe( + boost::asio::const_buffer(mem, info->len), + boost::bind(&usrp_e100_mmap_zero_copy_impl::release, shared_from_this(), info) + ); + } + + size_t get_num_recv_frames(void) const{ + return _rb_size.num_rx_frames; + } + + size_t get_recv_frame_size(void) const{ + return _frame_size; + } + + managed_send_buffer::sptr get_send_buff(double timeout){ + if (fp_verbose) std::cout << "get_send_buff: " << _send_index << std::endl; + + //grab pointers to the info and buffer + ring_buffer_info *info = (*_send_info) + _send_index; + void *mem = _send_buff + _frame_size*_send_index; + + //poll/wait for a ready frame + if (not (info->flags & RB_KERNEL)){ + pollfd pfd; + pfd.fd = _fd; + pfd.events = POLLOUT; + ssize_t poll_ret = ::poll(&pfd, 1, size_t(timeout*1e3)); + if (fp_verbose) std::cout << " POLLOUT: " << poll_ret << std::endl; + if (poll_ret <= 0) return managed_send_buffer::sptr(); + } + + //increment the index for the next call + if (++_send_index == size_t(_rb_size.num_tx_frames)) _send_index = 0; + + //return the managed buffer for this frame + if (fp_verbose) std::cout << " make_send_buff: " << _frame_size << std::endl; + return managed_send_buffer::make_safe( + boost::asio::mutable_buffer(mem, _frame_size), + boost::bind(&usrp_e100_mmap_zero_copy_impl::commit, shared_from_this(), info, _1) + ); + } + + size_t get_num_send_frames(void) const{ + return _rb_size.num_tx_frames; + } + + size_t get_send_frame_size(void) const{ + return _frame_size; + } + +private: + + void release(ring_buffer_info *info){ + if (fp_verbose) std::cout << "recv buff: release" << std::endl; + info->flags = RB_KERNEL; + } + + void commit(ring_buffer_info *info, size_t len){ + if (fp_verbose) std::cout << "send buff: commit " << len << std::endl; + info->len = len; + info->flags = RB_USER; + if (::write(_fd, NULL, 0) < 0){ + std::cerr << UHD_THROW_SITE_INFO("write error") << std::endl; + } + } + + int _fd; + + //the mapped memory itself + void *_mapped_mem; + + //mapped memory sizes + usrp_e_ring_buffer_size_t _rb_size; + size_t _frame_size, _map_size; + + //pointers to sections in the mapped memory + ring_buffer_info (*_recv_info)[], (*_send_info)[]; + char *_recv_buff, *_send_buff; + + //indexes into sub-sections of mapped memory + size_t _recv_index, _send_index; +}; + +/*********************************************************************** + * The zero copy interface make function + **********************************************************************/ +zero_copy_if::sptr usrp_e100_make_mmap_zero_copy(usrp_e100_iface::sptr iface){ + return zero_copy_if::sptr(new usrp_e100_mmap_zero_copy_impl(iface)); +} diff --git a/host/lib/usrp/usrp_e100/usrp_e100_regs.hpp b/host/lib/usrp/usrp_e100/usrp_e100_regs.hpp new file mode 100644 index 000000000..625fb2c35 --- /dev/null +++ b/host/lib/usrp/usrp_e100/usrp_e100_regs.hpp @@ -0,0 +1,198 @@ + + +//////////////////////////////////////////////////////////////// +// +// Memory map for embedded wishbone bus +// +//////////////////////////////////////////////////////////////// + +// All addresses are byte addresses. All accesses are word (16-bit) accesses. +// This means that address bit 0 is usually 0. +// There are 11 bits of address for the control. + +#ifndef INCLUDED_USRP_E100_REGS_HPP +#define INCLUDED_USRP_E100_REGS_HPP + +///////////////////////////////////////////////////// +// Slave pointers + +#define UE_REG_SLAVE(n) ((n)<<7) +#define UE_REG_SR_ADDR(n) ((UE_REG_SLAVE(5)) + (4*(n))) + +///////////////////////////////////////////////////// +// Slave 0 -- Misc Regs + +#define UE_REG_MISC_BASE UE_REG_SLAVE(0) + +#define UE_REG_MISC_LED UE_REG_MISC_BASE + 0 +#define UE_REG_MISC_SW UE_REG_MISC_BASE + 2 +#define UE_REG_MISC_CGEN_CTRL UE_REG_MISC_BASE + 4 +#define UE_REG_MISC_CGEN_ST UE_REG_MISC_BASE + 6 +#define UE_REG_MISC_TEST UE_REG_MISC_BASE + 8 +#define UE_REG_MISC_RX_LEN UE_REG_MISC_BASE + 10 +#define UE_REG_MISC_TX_LEN UE_REG_MISC_BASE + 12 +#define UE_REG_MISC_XFER_RATE UE_REG_MISC_BASE + 14 +#define UE_REG_MISC_COMPAT UE_REG_MISC_BASE + 16 + +///////////////////////////////////////////////////// +// Slave 1 -- UART +// CLKDIV is 16 bits, others are only 8 + +#define UE_REG_UART_BASE UE_REG_SLAVE(1) + +#define UE_REG_UART_CLKDIV UE_REG_UART_BASE + 0 +#define UE_REG_UART_TXLEVEL UE_REG_UART_BASE + 2 +#define UE_REG_UART_RXLEVEL UE_REG_UART_BASE + 4 +#define UE_REG_UART_TXCHAR UE_REG_UART_BASE + 6 +#define UE_REG_UART_RXCHAR UE_REG_UART_BASE + 8 + +///////////////////////////////////////////////////// +// Slave 2 -- SPI Core +// This should be accessed through the IOCTL +// Users should not touch directly + +#define UE_REG_SPI_BASE UE_REG_SLAVE(2) + +//spi slave constants +#define UE_SPI_SS_AD9522 (1 << 3) +#define UE_SPI_SS_AD9862 (1 << 2) +#define UE_SPI_SS_TX_DB (1 << 1) +#define UE_SPI_SS_RX_DB (1 << 0) + +//////////////////////////////////////////////// +// Slave 3 -- I2C Core +// This should be accessed through the IOCTL +// Users should not touch directly + +#define UE_REG_I2C_BASE UE_REG_SLAVE(3) + + +//////////////////////////////////////////////// +// Slave 4 -- GPIO + +#define UE_REG_GPIO_BASE UE_REG_SLAVE(4) + +#define UE_REG_GPIO_RX_IO UE_REG_GPIO_BASE + 0 +#define UE_REG_GPIO_TX_IO UE_REG_GPIO_BASE + 2 +#define UE_REG_GPIO_RX_DDR UE_REG_GPIO_BASE + 4 +#define UE_REG_GPIO_TX_DDR UE_REG_GPIO_BASE + 6 +#define UE_REG_GPIO_RX_SEL UE_REG_GPIO_BASE + 8 +#define UE_REG_GPIO_TX_SEL UE_REG_GPIO_BASE + 10 +#define UE_REG_GPIO_RX_DBG UE_REG_GPIO_BASE + 12 +#define UE_REG_GPIO_TX_DBG UE_REG_GPIO_BASE + 14 + +//possible bit values for sel when dbg is 0: +#define GPIO_SEL_SW 0 // if pin is an output, set by software in the io reg +#define GPIO_SEL_ATR 1 // if pin is an output, set by ATR logic + +//possible bit values for sel when dbg is 1: +#define GPIO_SEL_DEBUG_0 0 // if pin is an output, debug lines from FPGA fabric +#define GPIO_SEL_DEBUG_1 1 // if pin is an output, debug lines from FPGA fabric + + +//////////////////////////////////////////////////// +// Slave 5 -- Settings Bus +// +// Output-only, no readback, 32 registers total +// Each register must be written 32 bits at a time +// First the address xxx_xx00 and then xxx_xx10 + +#define UE_REG_SETTINGS_BASE UE_REG_SLAVE(5) + +/////////////////////////////////////////////////// +// Slave 6 -- ATR Controller +// 16 regs + +#define UE_REG_ATR_BASE UE_REG_SLAVE(6) + +#define UE_REG_ATR_IDLE_RXSIDE UE_REG_ATR_BASE + 0 +#define UE_REG_ATR_IDLE_TXSIDE UE_REG_ATR_BASE + 2 +#define UE_REG_ATR_INTX_RXSIDE UE_REG_ATR_BASE + 4 +#define UE_REG_ATR_INTX_TXSIDE UE_REG_ATR_BASE + 6 +#define UE_REG_ATR_INRX_RXSIDE UE_REG_ATR_BASE + 8 +#define UE_REG_ATR_INRX_TXSIDE UE_REG_ATR_BASE + 10 +#define UE_REG_ATR_FULL_RXSIDE UE_REG_ATR_BASE + 12 +#define UE_REG_ATR_FULL_TXSIDE UE_REG_ATR_BASE + 14 + +///////////////////////////////////////////////// +// DSP RX Regs +//////////////////////////////////////////////// +#define UE_REG_DSP_RX_FREQ UE_REG_SR_ADDR(0) +#define UE_REG_DSP_RX_SCALE_IQ UE_REG_SR_ADDR(1) // {scale_i,scale_q} +#define UE_REG_DSP_RX_DECIM_RATE UE_REG_SR_ADDR(2) // hb and decim rate +#define UE_REG_DSP_RX_DCOFFSET_I UE_REG_SR_ADDR(3) // Bit 31 high sets fixed offset mode, using lower 14 bits, // otherwise it is automatic +#define UE_REG_DSP_RX_DCOFFSET_Q UE_REG_SR_ADDR(4) // Bit 31 high sets fixed offset mode, using lower 14 bits +#define UE_REG_DSP_RX_MUX UE_REG_SR_ADDR(5) + +/////////////////////////////////////////////////// +// VITA RX CTRL regs +/////////////////////////////////////////////////// +// The following 3 are logically a single command register. +// They are clocked into the underlying fifo when time_ticks is written. +#define UE_REG_CTRL_RX_STREAM_CMD UE_REG_SR_ADDR(8) // {now, chain, num_samples(30) +#define UE_REG_CTRL_RX_TIME_SECS UE_REG_SR_ADDR(9) +#define UE_REG_CTRL_RX_TIME_TICKS UE_REG_SR_ADDR(10) +#define UE_REG_CTRL_RX_CLEAR_OVERRUN UE_REG_SR_ADDR(11) // write anything to clear overrun +#define UE_REG_CTRL_RX_VRT_HEADER UE_REG_SR_ADDR(12) // word 0 of packet. FPGA fills in packet counter +#define UE_REG_CTRL_RX_VRT_STREAM_ID UE_REG_SR_ADDR(13) // word 1 of packet. +#define UE_REG_CTRL_RX_VRT_TRAILER UE_REG_SR_ADDR(14) +#define UE_REG_CTRL_RX_NSAMPS_PER_PKT UE_REG_SR_ADDR(15) +#define UE_REG_CTRL_RX_NCHANNELS UE_REG_SR_ADDR(16) // 1 in basic case, up to 4 for vector sources + +///////////////////////////////////////////////// +// DSP TX Regs +//////////////////////////////////////////////// +#define UE_REG_DSP_TX_FREQ UE_REG_SR_ADDR(17) +#define UE_REG_DSP_TX_SCALE_IQ UE_REG_SR_ADDR(18) // {scale_i,scale_q} +#define UE_REG_DSP_TX_INTERP_RATE UE_REG_SR_ADDR(19) +#define UE_REG_DSP_TX_UNUSED UE_REG_SR_ADDR(20) +#define UE_REG_DSP_TX_MUX UE_REG_SR_ADDR(21) + +///////////////////////////////////////////////// +// VITA TX CTRL regs +//////////////////////////////////////////////// +#define UE_REG_CTRL_TX_NCHANNELS UE_REG_SR_ADDR(24) +#define UE_REG_CTRL_TX_CLEAR_UNDERRUN UE_REG_SR_ADDR(25) +#define UE_REG_CTRL_TX_REPORT_SID UE_REG_SR_ADDR(26) +#define UE_REG_CTRL_TX_POLICY UE_REG_SR_ADDR(27) + +#define UE_FLAG_CTRL_TX_POLICY_WAIT (0x1 << 0) +#define UE_FLAG_CTRL_TX_POLICY_NEXT_PACKET (0x1 << 1) +#define UE_FLAG_CTRL_TX_POLICY_NEXT_BURST (0x1 << 2) + +///////////////////////////////////////////////// +// VITA49 64 bit time (write only) +//////////////////////////////////////////////// + /*! + * \brief Time 64 flags + * + * <pre> + * + * 3 2 1 + * 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 + * +-----------------------------------------------------------+-+-+ + * | |S|P| + * +-----------------------------------------------------------+-+-+ + * + * P - PPS edge selection (0=negedge, 1=posedge, default=0) + * S - Source (0=sma, 1=mimo, 0=default) + * + * </pre> + */ +#define UE_REG_TIME64_SECS UE_REG_SR_ADDR(28) // value to set absolute secs to on next PPS +#define UE_REG_TIME64_TICKS UE_REG_SR_ADDR(29) // value to set absolute ticks to on next PPS +#define UE_REG_TIME64_FLAGS UE_REG_SR_ADDR(30) // flags - see chart above +#define UE_REG_TIME64_IMM UE_REG_SR_ADDR(31) // set immediate (0=latch on next pps, 1=latch immediate, default=0) +#define UE_REG_TIME64_TPS UE_REG_SR_ADDR(31) // clock ticks per second (counter rollover) + +//pps flags (see above) +#define UE_FLAG_TIME64_PPS_NEGEDGE (0 << 0) +#define UE_FLAG_TIME64_PPS_POSEDGE (1 << 0) +#define UE_FLAG_TIME64_PPS_SMA (0 << 1) +#define UE_FLAG_TIME64_PPS_MIMO (1 << 1) + +#define UE_FLAG_TIME64_LATCH_NOW 1 +#define UE_FLAG_TIME64_LATCH_NEXT_PPS 0 + +#endif + diff --git a/host/test/CMakeLists.txt b/host/test/CMakeLists.txt index 5d7433c67..bdbde4b2c 100644 --- a/host/test/CMakeLists.txt +++ b/host/test/CMakeLists.txt @@ -51,3 +51,7 @@ ENDFOREACH(test_source) # demo of a loadable module ######################################################################## ADD_LIBRARY(module_test MODULE module_test.cpp) + +INSTALL(TARGETS + RUNTIME DESTINATION ${PKG_DATA_DIR}/tests +) diff --git a/host/utils/CMakeLists.txt b/host/utils/CMakeLists.txt index 38e21c753..0edf5a78c 100644 --- a/host/utils/CMakeLists.txt +++ b/host/utils/CMakeLists.txt @@ -45,6 +45,18 @@ IF(ENABLE_USRP1) ) ENDIF(ENABLE_USRP1) +IF(ENABLE_USRP_E100) + INCLUDE_DIRECTORIES(${CMAKE_SOURCE_DIR}/lib/usrp/usrp_e100/include) + LIST(APPEND util_share_sources + fpga-downloader.cpp + clkgen-config.cpp + usrp-e-loopback.c + usrp-e-debug-pins.c + usrp-e-i2c.c + usrp-e-spi.c + ) +ENDIF(ENABLE_USRP_E100) + #for each source: build an executable and install FOREACH(util_source ${util_share_sources}) GET_FILENAME_COMPONENT(util_name ${util_source} NAME_WE) diff --git a/host/utils/clkgen-config.cpp b/host/utils/clkgen-config.cpp new file mode 100644 index 000000000..e8279b4ae --- /dev/null +++ b/host/utils/clkgen-config.cpp @@ -0,0 +1,296 @@ +/* -*- c++ -*- */ +/* + * Copyright 2003,2004,2008,2009 Free Software Foundation, Inc. + * + * This file is part of UHD + * + * GNU Radio is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 3, or (at your option) + * any later version. + * + * GNU Radio is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with GNU Radio; see the file COPYING. If not, write to + * the Free Software Foundation, Inc., 51 Franklin Street, + * Boston, MA 02110-1301, USA. +*/ + +#include <iostream> +#include <sstream> +#include <fstream> +#include <string> +#include <cstdlib> + +#include <fcntl.h> +#include <sys/types.h> +#include <sys/stat.h> +#include <sys/ioctl.h> + +#include <linux/spi/spidev.h> + + +// Programming data for clock gen chip +static const unsigned int config_data[] = { + 0x000024, + 0x023201, + 0x000081, + 0x000400, + 0x00104c, + 0x001101, + 0x001200, + 0x001300, + 0x001414, + 0x001500, + 0x001604, + 0x001704, + 0x001807, + 0x001900, + //0x001a00,//for debug + 0x001a32, + 0x001b12, + 0x001c44, + 0x001d00, + 0x001e00, + 0x00f062, + 0x00f162, + 0x00f262, + 0x00f362, + 0x00f462, + 0x00f562, + 0x00f662, + 0x00f762, + 0x00f862, + 0x00f962, + 0x00fa62, + 0x00fb62, + 0x00fc00, + 0x00fd00, + 0x019021, + 0x019100, + 0x019200, + 0x019333, + 0x019400, + 0x019500, + 0x019611, + 0x019700, + 0x019800, + 0x019900, + 0x019a00, + 0x019b00, + 0x01e003, + 0x01e102, + 0x023000, + 0x023201, + 0x0b0201, + 0x0b0300, + 0x001fff, + 0x0a0000, + 0x0a0100, + 0x0a0200, + 0x0a0302, + 0x0a0400, + 0x0a0504, + 0x0a060e, + 0x0a0700, + 0x0a0810, + 0x0a090e, + 0x0a0a00, + 0x0a0bf0, + 0x0a0c0b, + 0x0a0d01, + 0x0a0e90, + 0x0a0f01, + 0x0a1001, + 0x0a11e0, + 0x0a1201, + 0x0a1302, + 0x0a1430, + 0x0a1580, + 0x0a16ff, + 0x023201, + 0x0b0301, + 0x023201, +}; + + +const unsigned int CLKGEN_SELECT = 145; + + +enum gpio_direction {IN, OUT}; + +class gpio { + public: + + gpio(unsigned int gpio_num, gpio_direction pin_direction, bool close_action); + ~gpio(); + + bool get_value(); + void set_value(bool state); + + private: + + unsigned int gpio_num; + + std::stringstream base_path; + std::fstream value_file; + std::fstream direction_file; + bool close_action; // True set to input and release, false do nothing +}; + +class spidev { + public: + + spidev(std::string dev_name); + ~spidev(); + + void send(char *wbuf, char *rbuf, unsigned int nbytes); + + private: + + int fd; + +}; + +gpio::gpio(unsigned int _gpio_num, gpio_direction pin_direction, bool close_action) +{ + std::fstream export_file; + + gpio_num = _gpio_num; + + export_file.open("/sys/class/gpio/export", std::ios::out); + if (!export_file.is_open()) ///\todo Poor error handling + std::cout << "Failed to open gpio export file." << std::endl; + + export_file << gpio_num << std::endl; + + base_path << "/sys/class/gpio/gpio" << gpio_num << std::flush; + + std::string direction_file_name; + + direction_file_name = base_path.str() + "/direction"; + + direction_file.open(direction_file_name.c_str()); + if (!direction_file.is_open()) + std::cout << "Failed to open direction file." << std::endl; + if (pin_direction == OUT) + direction_file << "out" << std::endl; + else + direction_file << "in" << std::endl; + + std::string value_file_name; + + value_file_name = base_path.str() + "/value"; + + value_file.open(value_file_name.c_str(), std::ios_base::in | std::ios_base::out); + if (!value_file.is_open()) + std::cout << "Failed to open value file." << std::endl; +} + +bool gpio::get_value() +{ + + std::string val; + + std::getline(value_file, val); + value_file.seekg(0); + + if (val == "0") + return false; + else if (val == "1") + return true; + else + std::cout << "Data read from value file|" << val << "|" << std::endl; + + return false; +} + +void gpio::set_value(bool state) +{ + + if (state) + value_file << "1" << std::endl; + else + value_file << "0" << std::endl; +} + +gpio::~gpio() +{ + if (close_action) { + std::fstream unexport_file; + + direction_file << "in" << std::endl; + + unexport_file.open("/sys/class/gpio/unexport", std::ios::out); + if (!unexport_file.is_open()) ///\todo Poor error handling + std::cout << "Failed to open gpio export file." << std::endl; + + unexport_file << gpio_num << std::endl; + + } + +} + +spidev::spidev(std::string fname) +{ + int ret; + int mode = 0; + int speed = 12000; + int bits = 24; + + fd = open(fname.c_str(), O_RDWR); + + ret = ioctl(fd, SPI_IOC_WR_MODE, &mode); + ret = ioctl(fd, SPI_IOC_WR_MAX_SPEED_HZ, &speed); + ret = ioctl(fd, SPI_IOC_WR_BITS_PER_WORD, &bits); +} + + +spidev::~spidev() +{ + close(fd); +} + +void spidev::send(char *buf, char *rbuf, unsigned int nbytes) +{ + int ret; + + struct spi_ioc_transfer tr; + tr.tx_buf = (unsigned long) buf; + tr.rx_buf = (unsigned long) rbuf; + tr.len = nbytes; + tr.delay_usecs = 0; + tr.speed_hz = 12000000; + tr.bits_per_word = 24; + + ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr); + +} + +static void send_config_to_clkgen(gpio &chip_select, const unsigned int data[], unsigned int data_size) +{ + spidev spi("/dev/spidev1.0"); + unsigned int rbuf; + + for (unsigned int i = 0; i < data_size; i++) { + + std::cout << "sending " << std::hex << data[i] << std::endl; + chip_select.set_value(0); + spi.send((char *)&data[i], (char *)&rbuf, 4); + chip_select.set_value(1); + + }; +} + +int main(int argc, char *argv[]) +{ + + gpio clkgen_select(CLKGEN_SELECT, OUT, true); + + send_config_to_clkgen(clkgen_select, config_data, sizeof(config_data)/sizeof(unsigned int)); +} + diff --git a/host/utils/fpga-downloader.cpp b/host/utils/fpga-downloader.cpp new file mode 100644 index 000000000..80ee71600 --- /dev/null +++ b/host/utils/fpga-downloader.cpp @@ -0,0 +1,267 @@ +/* -*- c++ -*- */ +/* + * Copyright 2003,2004,2008,2009 Free Software Foundation, Inc. + * + * This file is part of GNU Radio + * + * GNU Radio is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 3, or (at your option) + * any later version. + * + * GNU Radio is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with GNU Radio; see the file COPYING. If not, write to + * the Free Software Foundation, Inc., 51 Franklin Street, + * Boston, MA 02110-1301, USA. +*/ + +#include <iostream> +#include <sstream> +#include <fstream> +#include <string> +#include <cstdlib> + +#include <fcntl.h> +#include <errno.h> +#include <sys/types.h> +#include <sys/stat.h> +#include <sys/ioctl.h> + +#include <linux/spi/spidev.h> + +/* + * Configuration connections + * + * CCK - MCSPI1_CLK + * DIN - MCSPI1_MOSI + * PROG_B - GPIO_175 - output (change mux) + * DONE - GPIO_173 - input (change mux) + * INIT_B - GPIO_114 - input (change mux) + * +*/ + +const unsigned int PROG_B = 175; +const unsigned int DONE = 173; +const unsigned int INIT_B = 114; + +static std::string bit_file = "safe_u1e.bin"; + +const int BUF_SIZE = 4096; + +enum gpio_direction {IN, OUT}; + +class gpio { + public: + + gpio(unsigned int gpio_num, gpio_direction pin_direction); + + bool get_value(); + void set_value(bool state); + + private: + + std::stringstream base_path; + std::fstream value_file; +}; + +class spidev { + public: + + spidev(std::string dev_name); + ~spidev(); + + void send(char *wbuf, char *rbuf, unsigned int nbytes); + + private: + + int fd; + +}; + +gpio::gpio(unsigned int gpio_num, gpio_direction pin_direction) +{ + std::fstream export_file; + + export_file.open("/sys/class/gpio/export", std::ios::out); + if (!export_file.is_open()) ///\todo Poor error handling + std::cout << "Failed to open gpio export file." << std::endl; + + export_file << gpio_num << std::endl; + + base_path << "/sys/class/gpio/gpio" << gpio_num << std::flush; + + std::fstream direction_file; + std::string direction_file_name; + + direction_file_name = base_path.str() + "/direction"; + + direction_file.open(direction_file_name.c_str()); + if (!direction_file.is_open()) + std::cout << "Failed to open direction file." << std::endl; + if (pin_direction == OUT) + direction_file << "out" << std::endl; + else + direction_file << "in" << std::endl; + + std::string value_file_name; + + value_file_name = base_path.str() + "/value"; + + value_file.open(value_file_name.c_str(), std::ios_base::in | std::ios_base::out); + if (!value_file.is_open()) + std::cout << "Failed to open value file." << std::endl; +} + +bool gpio::get_value() +{ + + std::string val; + + std::getline(value_file, val); + value_file.seekg(0); + + if (val == "0") + return false; + else if (val == "1") + return true; + else + std::cout << "Data read from value file|" << val << "|" << std::endl; + + return false; +} + +void gpio::set_value(bool state) +{ + + if (state) + value_file << "1" << std::endl; + else + value_file << "0" << std::endl; +} + +static void prepare_fpga_for_configuration(gpio &prog, gpio &init) +{ + + prog.set_value(true); + prog.set_value(false); + prog.set_value(true); + +#if 0 + bool ready_to_program(false); + unsigned int count(0); + do { + ready_to_program = init.get_value(); + count++; + + sleep(1); + } while (count < 10 && !ready_to_program); + + if (count == 10) { + std::cout << "FPGA not ready for programming." << std::endl; + exit(-1); + } +#endif +} + +spidev::spidev(std::string fname) +{ + int ret; + int mode = 0; + int speed = 12000000; + int bits = 8; + + fd = open(fname.c_str(), O_RDWR); + + ret = ioctl(fd, SPI_IOC_WR_MODE, &mode); + ret = ioctl(fd, SPI_IOC_WR_MAX_SPEED_HZ, &speed); + ret = ioctl(fd, SPI_IOC_WR_BITS_PER_WORD, &bits); +} + + +spidev::~spidev() +{ + close(fd); +} + +void spidev::send(char *buf, char *rbuf, unsigned int nbytes) +{ + int ret; + + struct spi_ioc_transfer tr; + tr.tx_buf = (unsigned long) buf; + tr.rx_buf = (unsigned long) rbuf; + tr.len = nbytes; + tr.delay_usecs = 0; + tr.speed_hz = 48000000; + tr.bits_per_word = 8; + + ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr); + +} + +static void send_file_to_fpga(std::string &file_name, gpio &error, gpio &done) +{ + std::ifstream bitstream; + + std::cout << "File name - " << file_name.c_str() << std::endl; + + bitstream.open(file_name.c_str(), std::ios::binary); + if (!bitstream.is_open()) + std::cout << "File " << file_name << " not opened succesfully." << std::endl; + + spidev spi("/dev/spidev1.0"); + char buf[BUF_SIZE]; + char rbuf[BUF_SIZE]; + + do { + bitstream.read(buf, BUF_SIZE); + spi.send(buf, rbuf, bitstream.gcount()); + + if (error.get_value()) + std::cout << "INIT_B went high, error occured." << std::endl; + + if (!done.get_value()) + std::cout << "Configuration complete." << std::endl; + + } while (bitstream.gcount() == BUF_SIZE); +} + +int main(int argc, char *argv[]) +{ + + gpio gpio_prog_b(PROG_B, OUT); + gpio gpio_init_b(INIT_B, IN); + gpio gpio_done (DONE, IN); + + if (argc == 2) + bit_file = argv[1]; + + bool module_found(false); + std::ifstream mod_file("/proc/modules"); + while (!mod_file.eof()) { + std::string line; + getline(mod_file, line); + if (line.find("usrp_e") != std::string::npos) + module_found = true; + } + mod_file.close(); + + if (module_found) { + std::cout << "USRP Embedded kernel module loaded, not loading FPGA." << std::endl; + return -1; + } + + std::cout << "FPGA config file: " << bit_file << std::endl; + + prepare_fpga_for_configuration(gpio_prog_b, gpio_init_b); + + std::cout << "Done = " << gpio_done.get_value() << std::endl; + + send_file_to_fpga(bit_file, gpio_init_b, gpio_done); +} + diff --git a/host/utils/usrp-e-debug-pins.c b/host/utils/usrp-e-debug-pins.c new file mode 100644 index 000000000..1ed2c8983 --- /dev/null +++ b/host/utils/usrp-e-debug-pins.c @@ -0,0 +1,77 @@ +#include <stdio.h> +#include <stdlib.h> +#include <unistd.h> +#include <sys/types.h> +#include <fcntl.h> +#include <string.h> +#include <sys/ioctl.h> + +#include <linux/usrp_e.h> +#include "usrp_e_regs.hpp" + +// Usage: usrp_e_gpio <string> + +static int fp; + +static int read_reg(__u16 reg) +{ + int ret; + struct usrp_e_ctl16 d; + + d.offset = reg; + d.count = 1; + ret = ioctl(fp, USRP_E_READ_CTL16, &d); + return d.buf[0]; +} + +static void write_reg(__u16 reg, __u16 val) +{ + int ret; + struct usrp_e_ctl16 d; + + d.offset = reg; + d.count = 1; + d.buf[0] = val; + ret = ioctl(fp, USRP_E_WRITE_CTL16, &d); +} + +int main(int argc, char *argv[]) +{ + int test; + + test = 0; + if (argc < 2) { + printf("%s 0|1|off\n", argv[0]); + } + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + if (fp < 0) { + perror("Open failed"); + return -1; + } + + if (strcmp(argv[1], "0") == 0) { + printf("Selected 0 based on %s\n", argv[1]); + write_reg(UE_REG_GPIO_TX_DDR, 0xFFFF); + write_reg(UE_REG_GPIO_RX_DDR, 0xFFFF); + write_reg(UE_REG_GPIO_TX_SEL, 0x0); + write_reg(UE_REG_GPIO_RX_SEL, 0x0); + write_reg(UE_REG_GPIO_TX_DBG, 0xFFFF); + write_reg(UE_REG_GPIO_RX_DBG, 0xFFFF); + } else if (strcmp(argv[1], "1") == 0) { + printf("Selected 1 based on %s\n", argv[1]); + write_reg(UE_REG_GPIO_TX_DDR, 0xFFFF); + write_reg(UE_REG_GPIO_RX_DDR, 0xFFFF); + write_reg(UE_REG_GPIO_TX_SEL, 0xFFFF); + write_reg(UE_REG_GPIO_RX_SEL, 0xFFFF); + write_reg(UE_REG_GPIO_TX_DBG, 0xFFFF); + write_reg(UE_REG_GPIO_RX_DBG, 0xFFFF); + } else { + printf("Selected off based on %s\n", argv[1]); + write_reg(UE_REG_GPIO_TX_DDR, 0x0); + write_reg(UE_REG_GPIO_RX_DDR, 0x0); + } + + return 0; +} diff --git a/host/utils/usrp-e-i2c.c b/host/utils/usrp-e-i2c.c new file mode 100644 index 000000000..c6fd4c632 --- /dev/null +++ b/host/utils/usrp-e-i2c.c @@ -0,0 +1,87 @@ +#include <stdio.h> +#include <stdlib.h> +#include <string.h> +#include <unistd.h> +#include <sys/types.h> +#include <fcntl.h> +#include <sys/ioctl.h> + +#include <linux/usrp_e.h> + +// Usage: usrp_e_i2c w address data0 data1 data 2 .... +// Usage: usrp_e_i2c r address count + +int main(int argc, char *argv[]) +{ + int fp, ret, i, tmp; + struct usrp_e_i2c *i2c_msg; + int direction, address, count; + + if (argc < 3) { + printf("Usage: usrp-e-i2c w address data0 data1 data2 ...\n"); + printf("Usage: usrp-e-i2c r address count\n"); + printf("All addresses and data in hex.\n"); + exit(-1); + } + + if (strcmp(argv[1], "r") == 0) { + direction = 0; + } else if (strcmp(argv[1], "w") == 0) { + direction = 1; + } else { + return -1; + } + + sscanf(argv[2], "%X", &address); + printf("Address = %X\n", address); + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + if (fp < 0) { + perror("Open failed"); + return -1; + } + +// sleep(1); + + if (direction) { + count = argc - 3; + } else { + sscanf(argv[3], "%X", &count); + } + printf("Count = %X\n", count); + + i2c_msg = malloc(sizeof(i2c_msg) + count * sizeof(char)); + + i2c_msg->addr = address; + i2c_msg->len = count; + + for (i = 0; i < count; i++) { + i2c_msg->data[i] = i; + } + + if (direction) { + // Write + + for (i=0; i<count; i++) { + sscanf(argv[3+i], "%X", &tmp); + i2c_msg->data[i] = tmp; + } + + ret = ioctl(fp, USRP_E_I2C_WRITE, i2c_msg); + printf("Return value from i2c_write ioctl: %d\n", ret); + } else { + // Read + + ret = ioctl(fp, USRP_E_I2C_READ, i2c_msg); + printf("Return value from i2c_read ioctl: %d\n", ret); + + printf("Ioctl: %d Data read :", ret); + for (i=0; i<count; i++) { + printf(" %X", i2c_msg->data[i]); + } + printf("\n"); + + } + return 0; +} diff --git a/host/utils/usrp-e-loopback.c b/host/utils/usrp-e-loopback.c new file mode 100644 index 000000000..454d81ba7 --- /dev/null +++ b/host/utils/usrp-e-loopback.c @@ -0,0 +1,231 @@ +#include <stdio.h> +#include <sys/types.h> +#include <fcntl.h> +#include <pthread.h> +#include <stdlib.h> +#include <unistd.h> +#include <stddef.h> +#include <sys/mman.h> +#include <linux/usrp_e.h> + +#define MAX_PACKET_SIZE 1016 +static int packet_data_length; +static int error; + +struct pkt { + int len; + int checksum; + int seq_num; + short data[]; +}; + +static int length_array[2048]; +static int length_array_tail = 0; +static int length_array_head = 0; + +pthread_mutex_t length_array_mutex; //gotta lock the index to keep it from getting hosed + +//yes this is a circular buffer that does not check empty +//no i don't want to hear about it +void push_length_array(int length) { + pthread_mutex_lock(&length_array_mutex); + if(length_array_tail > 2047) length_array_tail = 0; + length_array[length_array_tail++] = length; + pthread_mutex_unlock(&length_array_mutex); +} + +int pop_length_array(void) { + int retval; + pthread_mutex_lock(&length_array_mutex); + if(length_array_head > 2047) length_array_head = 0; + retval = length_array[length_array_head++]; + pthread_mutex_unlock(&length_array_mutex); + return retval; +} + +static int fp; + +static int calc_checksum(struct pkt *p) +{ + int i, sum; + + i = 0; + sum = 0; + + for (i=0; i < p->len; i++) + sum ^= p->data[i]; + + sum ^= p->seq_num; + sum ^= p->len; + + return sum; +} + +static void *read_thread(void *threadid) +{ + char *rx_data; + int cnt, prev_seq_num, pkt_count, seq_num_failure; + struct pkt *p; + unsigned long bytes_transfered, elapsed_seconds; + struct timeval start_time, finish_time; + int expected_count; + + printf("Greetings from the reading thread!\n"); + + bytes_transfered = 0; + gettimeofday(&start_time, NULL); + + // IMPORTANT: must assume max length packet from fpga + rx_data = malloc(2048); + p = (struct pkt *) ((void *)rx_data); + + prev_seq_num = 0; + pkt_count = 0; + seq_num_failure = 0; + + while (1) { + + cnt = read(fp, rx_data, 2048); + if (cnt < 0) + printf("Error returned from read: %d, sequence number = %d\n", cnt, p->seq_num); + +// printf("p->seq_num = %d\n", p->seq_num); + + + pkt_count++; + + if (p->seq_num != prev_seq_num + 1) { + printf("Sequence number fail, current = %d, previous = %d, pkt_count = %d\n", + p->seq_num, prev_seq_num, pkt_count); + + seq_num_failure ++; + if (seq_num_failure > 2) + error = 1; + } + + expected_count = pop_length_array()*2+12; + if(cnt != expected_count) { + printf("Received %d bytes, expected %d\n", cnt, expected_count); + } + + prev_seq_num = p->seq_num; + + if (calc_checksum(p) != p->checksum) { + printf("Checksum fail packet = %X, expected = %X, pkt_count = %d\n", + calc_checksum(p), p->checksum, pkt_count); + error = 1; + } + + bytes_transfered += cnt; + + if (bytes_transfered > (100 * 1000000)) { + gettimeofday(&finish_time, NULL); + elapsed_seconds = finish_time.tv_sec - start_time.tv_sec; + + printf("RX data transfer rate = %f K Samples/second\n", + (float) bytes_transfered / (float) elapsed_seconds / 4000); + + + start_time = finish_time; + bytes_transfered = 0; + } + + +// printf("."); +// fflush(stdout); +// printf("\n"); + } + +} + +static void *write_thread(void *threadid) +{ + int seq_number, i, cnt; + void *tx_data; + struct pkt *p; + + printf("Greetings from the write thread!\n"); + + tx_data = malloc(2048); + p = (struct pkt *) ((void *)tx_data); + + for (i=0; i < packet_data_length; i++) +// p->data[i] = random() >> 16; + p->data[i] = i; + + seq_number = 1; + + while (1) { + p->seq_num = seq_number++; + + if (packet_data_length > 0) + p->len = packet_data_length; + else + p->len = (random()<<1 & 0x1ff) + (1004 - 512); + + push_length_array(p->len); + + p->checksum = calc_checksum(p); + + cnt = write(fp, tx_data, p->len * 2 + 12); + if (cnt < 0) + printf("Error returned from write: %d\n", cnt); +// sleep(1); + } +} + + +int main(int argc, char *argv[]) +{ + pthread_t tx, rx; + pthread_mutex_init(&length_array_mutex, 0); + long int t; + struct sched_param s = { + .sched_priority = 1 + }; + void *rb; + struct usrp_transfer_frame *tx_rb, *rx_rb; + + if (argc < 2) { + printf("%s data_size\n", argv[0]); + return -1; + } + + packet_data_length = atoi(argv[1]); + if(packet_data_length > MAX_PACKET_SIZE) { + printf("Packet size must be smaller than %i\n", MAX_PACKET_SIZE); + exit(-1); + } + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + + rb = mmap(0, 202 * 4096, PROT_READ|PROT_WRITE, MAP_SHARED, fp, 0); + if (!rb) { + printf("mmap failed\n"); + exit; + } + + + sched_setscheduler(0, SCHED_RR, &s); + error = 0; + +#if 1 + if (pthread_create(&rx, NULL, read_thread, (void *) t)) { + printf("Failed to create rx thread\n"); + exit(-1); + } + + sleep(1); +#endif + + if (pthread_create(&tx, NULL, write_thread, (void *) t)) { + printf("Failed to create tx thread\n"); + exit(-1); + } + +// while (!error) + sleep(1000000000); + + printf("Done sleeping\n"); +} diff --git a/host/utils/usrp-e-spi.c b/host/utils/usrp-e-spi.c new file mode 100644 index 000000000..5203f56a8 --- /dev/null +++ b/host/utils/usrp-e-spi.c @@ -0,0 +1,54 @@ +#include <stdio.h> +#include <stdlib.h> +#include <unistd.h> +#include <sys/types.h> +#include <fcntl.h> +#include <sys/ioctl.h> + +#include <linux/usrp_e.h> + +// Usage: usrp_e_spi w|rb slave data + +int main(int argc, char *argv[]) +{ + int fp, slave, length, ret; + unsigned int data; + struct usrp_e_spi spi_dat; + + if (argc < 5) { + printf("Usage: usrp_e_spi w|rb slave transfer_length data\n"); + exit(-1); + } + + slave = atoi(argv[2]); + length = atoi(argv[3]); + data = atoll(argv[4]); + + printf("Data = %X\n", data); + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + if (fp < 0) { + perror("Open failed"); + return -1; + } + +// sleep(1); + + + spi_dat.slave = slave; + spi_dat.data = data; + spi_dat.length = length; + spi_dat.flags = UE_SPI_PUSH_FALL | UE_SPI_LATCH_RISE; + + if (*argv[1] == 'r') { + spi_dat.readback = 1; + ret = ioctl(fp, USRP_E_SPI, &spi_dat); + printf("Ioctl returns: %d, Data returned = %d\n", ret, spi_dat.data); + } else { + spi_dat.readback = 0; + ioctl(fp, USRP_E_SPI, &spi_dat); + } + + return 0; +} diff --git a/host/utils/usrp_e_regs.hpp b/host/utils/usrp_e_regs.hpp new file mode 100644 index 000000000..a4f42093e --- /dev/null +++ b/host/utils/usrp_e_regs.hpp @@ -0,0 +1,196 @@ + + +//////////////////////////////////////////////////////////////// +// +// Memory map for embedded wishbone bus +// +//////////////////////////////////////////////////////////////// + +// All addresses are byte addresses. All accesses are word (16-bit) accesses. +// This means that address bit 0 is usually 0. +// There are 11 bits of address for the control. + +#ifndef __USRP_E_REGS_H +#define __USRP_E_REGS_H + +///////////////////////////////////////////////////// +// Slave pointers + +#define UE_REG_SLAVE(n) ((n)<<7) +#define UE_REG_SR_ADDR(n) ((UE_REG_SLAVE(5)) + (4*(n))) + +///////////////////////////////////////////////////// +// Slave 0 -- Misc Regs + +#define UE_REG_MISC_BASE UE_REG_SLAVE(0) + +#define UE_REG_MISC_LED UE_REG_MISC_BASE + 0 +#define UE_REG_MISC_SW UE_REG_MISC_BASE + 2 +#define UE_REG_MISC_CGEN_CTRL UE_REG_MISC_BASE + 4 +#define UE_REG_MISC_CGEN_ST UE_REG_MISC_BASE + 6 +#define UE_REG_MISC_TEST UE_REG_MISC_BASE + 8 +#define UE_REG_MISC_RX_LEN UE_REG_MISC_BASE + 10 +#define UE_REG_MISC_TX_LEN UE_REG_MISC_BASE + 12 + +///////////////////////////////////////////////////// +// Slave 1 -- UART +// CLKDIV is 16 bits, others are only 8 + +#define UE_REG_UART_BASE UE_REG_SLAVE(1) + +#define UE_REG_UART_CLKDIV UE_REG_UART_BASE + 0 +#define UE_REG_UART_TXLEVEL UE_REG_UART_BASE + 2 +#define UE_REG_UART_RXLEVEL UE_REG_UART_BASE + 4 +#define UE_REG_UART_TXCHAR UE_REG_UART_BASE + 6 +#define UE_REG_UART_RXCHAR UE_REG_UART_BASE + 8 + +///////////////////////////////////////////////////// +// Slave 2 -- SPI Core +// This should be accessed through the IOCTL +// Users should not touch directly + +#define UE_REG_SPI_BASE UE_REG_SLAVE(2) + +//spi slave constants +#define UE_SPI_SS_AD9522 (1 << 3) +#define UE_SPI_SS_AD9862 (1 << 2) +#define UE_SPI_SS_TX_DB (1 << 1) +#define UE_SPI_SS_RX_DB (1 << 0) + +//////////////////////////////////////////////// +// Slave 3 -- I2C Core +// This should be accessed through the IOCTL +// Users should not touch directly + +#define UE_REG_I2C_BASE UE_REG_SLAVE(3) + + +//////////////////////////////////////////////// +// Slave 4 -- GPIO + +#define UE_REG_GPIO_BASE UE_REG_SLAVE(4) + +#define UE_REG_GPIO_RX_IO UE_REG_GPIO_BASE + 0 +#define UE_REG_GPIO_TX_IO UE_REG_GPIO_BASE + 2 +#define UE_REG_GPIO_RX_DDR UE_REG_GPIO_BASE + 4 +#define UE_REG_GPIO_TX_DDR UE_REG_GPIO_BASE + 6 +#define UE_REG_GPIO_RX_SEL UE_REG_GPIO_BASE + 8 +#define UE_REG_GPIO_TX_SEL UE_REG_GPIO_BASE + 10 +#define UE_REG_GPIO_RX_DBG UE_REG_GPIO_BASE + 12 +#define UE_REG_GPIO_TX_DBG UE_REG_GPIO_BASE + 14 + +//possible bit values for sel when dbg is 0: +#define GPIO_SEL_SW 0 // if pin is an output, set by software in the io reg +#define GPIO_SEL_ATR 1 // if pin is an output, set by ATR logic + +//possible bit values for sel when dbg is 1: +#define GPIO_SEL_DEBUG_0 0 // if pin is an output, debug lines from FPGA fabric +#define GPIO_SEL_DEBUG_1 1 // if pin is an output, debug lines from FPGA fabric + + +//////////////////////////////////////////////////// +// Slave 5 -- Settings Bus +// +// Output-only, no readback, 32 registers total +// Each register must be written 32 bits at a time +// First the address xxx_xx00 and then xxx_xx10 + +#define UE_REG_SETTINGS_BASE UE_REG_SLAVE(5) + +/////////////////////////////////////////////////// +// Slave 6 -- ATR Controller +// 16 regs + +#define UE_REG_ATR_BASE UE_REG_SLAVE(6) + +#define UE_REG_ATR_IDLE_RXSIDE UE_REG_ATR_BASE + 0 +#define UE_REG_ATR_IDLE_TXSIDE UE_REG_ATR_BASE + 2 +#define UE_REG_ATR_INTX_RXSIDE UE_REG_ATR_BASE + 4 +#define UE_REG_ATR_INTX_TXSIDE UE_REG_ATR_BASE + 6 +#define UE_REG_ATR_INRX_RXSIDE UE_REG_ATR_BASE + 8 +#define UE_REG_ATR_INRX_TXSIDE UE_REG_ATR_BASE + 10 +#define UE_REG_ATR_FULL_RXSIDE UE_REG_ATR_BASE + 12 +#define UE_REG_ATR_FULL_TXSIDE UE_REG_ATR_BASE + 14 + +///////////////////////////////////////////////// +// DSP RX Regs +//////////////////////////////////////////////// +#define UE_REG_DSP_RX_FREQ UE_REG_SR_ADDR(0) +#define UE_REG_DSP_RX_SCALE_IQ UE_REG_SR_ADDR(1) // {scale_i,scale_q} +#define UE_REG_DSP_RX_DECIM_RATE UE_REG_SR_ADDR(2) // hb and decim rate +#define UE_REG_DSP_RX_DCOFFSET_I UE_REG_SR_ADDR(3) // Bit 31 high sets fixed offset mode, using lower 14 bits, // otherwise it is automatic +#define UE_REG_DSP_RX_DCOFFSET_Q UE_REG_SR_ADDR(4) // Bit 31 high sets fixed offset mode, using lower 14 bits +#define UE_REG_DSP_RX_MUX UE_REG_SR_ADDR(5) + +/////////////////////////////////////////////////// +// VITA RX CTRL regs +/////////////////////////////////////////////////// +// The following 3 are logically a single command register. +// They are clocked into the underlying fifo when time_ticks is written. +#define UE_REG_CTRL_RX_STREAM_CMD UE_REG_SR_ADDR(8) // {now, chain, num_samples(30) +#define UE_REG_CTRL_RX_TIME_SECS UE_REG_SR_ADDR(9) +#define UE_REG_CTRL_RX_TIME_TICKS UE_REG_SR_ADDR(10) +#define UE_REG_CTRL_RX_CLEAR_OVERRUN UE_REG_SR_ADDR(11) // write anything to clear overrun +#define UE_REG_CTRL_RX_VRT_HEADER UE_REG_SR_ADDR(12) // word 0 of packet. FPGA fills in packet counter +#define UE_REG_CTRL_RX_VRT_STREAM_ID UE_REG_SR_ADDR(13) // word 1 of packet. +#define UE_REG_CTRL_RX_VRT_TRAILER UE_REG_SR_ADDR(14) +#define UE_REG_CTRL_RX_NSAMPS_PER_PKT UE_REG_SR_ADDR(15) +#define UE_REG_CTRL_RX_NCHANNELS UE_REG_SR_ADDR(16) // 1 in basic case, up to 4 for vector sources + +///////////////////////////////////////////////// +// DSP TX Regs +//////////////////////////////////////////////// +#define UE_REG_DSP_TX_FREQ UE_REG_SR_ADDR(17) +#define UE_REG_DSP_TX_SCALE_IQ UE_REG_SR_ADDR(18) // {scale_i,scale_q} +#define UE_REG_DSP_TX_INTERP_RATE UE_REG_SR_ADDR(19) +#define UE_REG_DSP_TX_UNUSED UE_REG_SR_ADDR(20) +#define UE_REG_DSP_TX_MUX UE_REG_SR_ADDR(21) + +///////////////////////////////////////////////// +// VITA TX CTRL regs +//////////////////////////////////////////////// +#define UE_REG_CTRL_TX_NCHANNELS UE_REG_SR_ADDR(24) +#define UE_REG_CTRL_TX_CLEAR_UNDERRUN UE_REG_SR_ADDR(25) +#define UE_REG_CTRL_TX_REPORT_SID UE_REG_SR_ADDR(26) +#define UE_REG_CTRL_TX_POLICY UE_REG_SR_ADDR(27) + +#define UE_FLAG_CTRL_TX_POLICY_WAIT (0x1 << 0) +#define UE_FLAG_CTRL_TX_POLICY_NEXT_PACKET (0x1 << 1) +#define UE_FLAG_CTRL_TX_POLICY_NEXT_BURST (0x1 << 2) + +///////////////////////////////////////////////// +// VITA49 64 bit time (write only) +//////////////////////////////////////////////// + /*! + * \brief Time 64 flags + * + * <pre> + * + * 3 2 1 + * 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 + * +-----------------------------------------------------------+-+-+ + * | |S|P| + * +-----------------------------------------------------------+-+-+ + * + * P - PPS edge selection (0=negedge, 1=posedge, default=0) + * S - Source (0=sma, 1=mimo, 0=default) + * + * </pre> + */ +#define UE_REG_TIME64_SECS UE_REG_SR_ADDR(28) // value to set absolute secs to on next PPS +#define UE_REG_TIME64_TICKS UE_REG_SR_ADDR(29) // value to set absolute ticks to on next PPS +#define UE_REG_TIME64_FLAGS UE_REG_SR_ADDR(30) // flags - see chart above +#define UE_REG_TIME64_IMM UE_REG_SR_ADDR(31) // set immediate (0=latch on next pps, 1=latch immediate, default=0) +#define UE_REG_TIME64_TPS UE_REG_SR_ADDR(31) // clock ticks per second (counter rollover) + +//pps flags (see above) +#define UE_FLAG_TIME64_PPS_NEGEDGE (0 << 0) +#define UE_FLAG_TIME64_PPS_POSEDGE (1 << 0) +#define UE_FLAG_TIME64_PPS_SMA (0 << 1) +#define UE_FLAG_TIME64_PPS_MIMO (1 << 1) + +#define UE_FLAG_TIME64_LATCH_NOW 1 +#define UE_FLAG_TIME64_LATCH_NEXT_PPS 0 + +#endif + diff --git a/images/Makefile b/images/Makefile index 79e7b3362..34943cc59 100644 --- a/images/Makefile +++ b/images/Makefile @@ -114,18 +114,18 @@ $(_usrp2_fpga_bin): endif ######################################################################## -# USRP2 fpga +# USRP-E100 fpga ######################################################################## ifdef HAS_XTCLSH -_usrp2p_fpga_dir = $(TOP_FPGA_DIR)/usrp2/top/u2plus -_usrp2p_fpga_bin = $(BUILT_IMAGES_DIR)/usrp2p_fpga.bin -IMAGES_LIST += $(_usrp2p_fpga_bin) +_usrp_e100_fpga_dir = $(TOP_FPGA_DIR)/usrp2/top/u1e +_usrp_e100_fpga_bin = $(BUILT_IMAGES_DIR)/usrp_e100_fpga.bin +IMAGES_LIST += $(_usrp_e100_fpga_bin) -$(_usrp2p_fpga_bin): - cd $(_usrp2p_fpga_dir) && make -f Makefile.udp clean - cd $(_usrp2p_fpga_dir) && make -f Makefile.udp bin - cp $(_usrp2p_fpga_dir)/build-ISE12/u2plus.bin $@ +$(_usrp_e100_fpga_bin): + cd $(_usrp_e100_fpga_dir) && make clean + cd $(_usrp_e100_fpga_dir) && make bin + cp $(_usrp_e100_fpga_dir)/build/u1e.bin $@ endif |