1) u2p has added a new signal from the SRAM to the pinout, RAM_ZZ

which allows the SRAM to be placed in a sleep mode. This pin was
erroniously pulled high at the top level rendering the SRAM unusable.

2) Added declaration for extramfifo debug bus which had got deleted
at some point in the past

3) Created a debug bundle of signals from extsramfifo to help diagnose
problem 1)

4) u2p Rev1 PCB ommits control of any of the SRAM chip selects. Made a
code change so that control logic does not rely on the presence of this
pin and ensuring that the SRAM is always placed in READ mode in any idle cycles.

2 files changed, 12 insertions, 9 deletions

diff --git a/usrp2/extramfifo/ext_fifo.v b/usrp2/extramfifo/ext_fifo.v
index 2a8d57448..44229f846 100644
--- a/usrp2/extramfifo/ext_fifo.v
+++ b/usrp2/extramfifo/ext_fifo.v
@@ -46,8 +46,6 @@ module ext_fifo
    wire [EXT_WIDTH-1:0] read_data;
    wire 		full1, empty1;
    wire 		almost_full2, full2, empty2;
-   wire [INT_WIDTH-1:0] data_to_fifo;
-   wire [INT_WIDTH-1:0] data_from_fifo;
    wire [FIFO_DEPTH-1:0] capacity;
    wire 		 space_avail;
    wire 		 data_avail;
@@ -151,12 +149,14 @@ module ext_fifo
    
 
    
-   always @ (posedge int_clk)
-     debug[31:28] <= {empty2,full1,dst_rdy_i,src_rdy_i };
+//   always @ (posedge int_clk)
+//     debug[31:28] <= {empty2,full1,dst_rdy_i,src_rdy_i };
    
    always @ (posedge ext_clk)
-     debug[27:0] <= {RAM_WEn,RAM_CE1n,RAM_A[3:0],read_data[17:0],empty1,space_avail,data_avail,almost_full2 };
-
+ //    debug[27:0] <= {RAM_WEn,RAM_CE1n,RAM_A[3:0],read_data[17:0],empty1,space_avail,data_avail,almost_full2 };
+     debug[31:0] <= {7'h0,src_rdy_i,read_input_fifo,write_output_fifo,dst_rdy_i,full2,almost_full2,empty2,full1,empty1,write_data[7:0],read_data[7:0]};
+   
+     
    always@ (posedge ext_clk)
      //     debug2[31:0] <= {write_data[15:0],read_data[15:0]};
      debug2[31:0] <= 0;
diff --git a/usrp2/extramfifo/nobl_if.v b/usrp2/extramfifo/nobl_if.v
index 391a841e8..7ff7eaa03 100644
--- a/usrp2/extramfifo/nobl_if.v
+++ b/usrp2/extramfifo/nobl_if.v
@@ -50,18 +50,21 @@ module nobl_if
 	  address_pipe1 <= 0;
 	  write_pipe1 <= 0;
 	  data_out_pipe1  <= 0;
+	  RAM_WEn <= 1;
+	  RAM_CE1n <= 1;
+	  
        end
      else
        begin
 	  enable_pipe1 <= enable;
-	  RAM_CE1n <= ~enable;  // Creates IOB flob
-	  
+	  RAM_CE1n <= ~enable;  // Creates IOB flop
+	  RAM_WEn <= ~write;  // Creates IOB flop
 	  
 	  if (enable)
 	    begin
 	       address_pipe1 <= address;
 	       write_pipe1 <= write;
-	       RAM_WEn <= ~write;  // Creates IOB flob
+//	       RAM_WEn <= ~write;  // Creates IOB flop
 	       
 	       
 	       if (write)