Merge branch 'u1e' into merge_u1e

* u1e: (130 commits)
  invert led signals because they are active low
  duh
  allow for CS to rise before, at the same time, or after OE
  better debug pins
  watch the ethernet chip select on our debug bus
  fix timing issue on DAC outputs with rev 2.  This puts the whole system on a 90 degree phase shift
  send all gpmc signals to mictor
  updated pins to match rev2, removed dip switch, etc.  seems to compile ok.
  pins are different on rev2
  fixed makefile to compile with our new system
  add register to tell host about compatibility level and which image we are using
  move declaration to make loopback compile
  no need for protocol headers since we're not doing ethernet
  match the signal names in this design
  debug pins cleanup
  properly integrate the new tx chain
  catch up with tx_policy
  attach run_tx and run_rx to leds
  connect atr
  delay the q channel to make the channels line up on the AD9862
  ...

Conflicts:
	usrp2/control_lib/Makefile.srcs

14 files changed, 623 insertions, 18 deletions

diff --git a/usrp2/control_lib/Makefile.srcs b/usrp2/control_lib/Makefile.srcs
index 666ac344c..d3bb7e2c8 100644
--- a/usrp2/control_lib/Makefile.srcs
+++ b/usrp2/control_lib/Makefile.srcs
@@ -46,4 +46,7 @@ shortfifo.v \
 medfifo.v \
 s3a_icap_wb.v \
 bootram.v \
+nsgpio16LE.v \
+settings_bus_16LE.v \
+atr_controller16.v \
 ))
diff --git a/usrp2/control_lib/atr_controller16.v b/usrp2/control_lib/atr_controller16.v
new file mode 100644
index 000000000..3d8b5b1e9
--- /dev/null
+++ b/usrp2/control_lib/atr_controller16.v
@@ -0,0 +1,60 @@
+
+// Automatic transmit/receive switching of control pins to daughterboards
+// Store everything in registers for now, but could use a RAM for more
+// complex state machines in the future
+
+module atr_controller16
+  (input clk_i, input rst_i,
+   input [5:0] adr_i, input [1:0] sel_i, input [15:0] dat_i, output reg [15:0] dat_o,
+   input we_i, input stb_i, input cyc_i, output reg ack_o,
+   input run_rx, input run_tx, input [31:0] master_time,
+   output [31:0] ctrl_lines);
+   
+   reg [3:0] state;
+   reg [31:0] atr_ram [0:15];  // DP distributed RAM
+
+   wire [3:0] sel_int = { (sel_i[1] & adr_i[1]), (sel_i[0] & adr_i[1]),
+			  (sel_i[1] & ~adr_i[1]), (sel_i[0] & ~adr_i[1]) };
+   
+   // WB Interface
+   always @(posedge clk_i)
+     if(we_i & stb_i & cyc_i)
+       begin
+	  if(sel_int[3])
+	    atr_ram[adr_i[5:2]][31:24] <= dat_i[15:8];
+	  if(sel_int[2])
+	    atr_ram[adr_i[5:2]][23:16] <= dat_i[7:0];
+	  if(sel_int[1])
+	    atr_ram[adr_i[5:2]][15:8] <= dat_i[15:8];
+	  if(sel_int[0])
+	    atr_ram[adr_i[5:2]][7:0] <= dat_i[7:0];
+       end // if (we_i & stb_i & cyc_i)
+
+   always @(posedge clk_i)
+     dat_o <= adr_i[1] ? atr_ram[adr_i[5:2]][31:16] : atr_ram[adr_i[5:2]][15:0];
+   
+   always @(posedge clk_i)
+     ack_o <= stb_i & cyc_i & ~ack_o;
+
+   // Control side of DP RAM
+   assign     ctrl_lines = atr_ram[state];
+
+   // Put a more complex state machine with time delays and multiple states here
+   //  if daughterboard requires more complex sequencing
+   localparam ATR_IDLE = 4'd0;
+   localparam ATR_TX = 4'd1;
+   localparam ATR_RX = 4'd2;
+   localparam ATR_FULL_DUPLEX = 4'd3;
+   
+   always @(posedge clk_i)
+     if(rst_i)
+       state <= ATR_IDLE;
+     else
+       case ({run_rx,run_tx})
+	 2'b00 : state <= ATR_IDLE;
+	 2'b01 : state <= ATR_TX;
+	 2'b10 : state <= ATR_RX;
+	 2'b11 : state <= ATR_FULL_DUPLEX;
+       endcase // case({run_rx,run_tx})
+   
+endmodule // atr_controller16
diff --git a/usrp2/control_lib/newfifo/fifo_pacer.v b/usrp2/control_lib/newfifo/fifo_pacer.v
new file mode 100644
index 000000000..1bf03ab6e
--- /dev/null
+++ b/usrp2/control_lib/newfifo/fifo_pacer.v
@@ -0,0 +1,24 @@
+
+
+module fifo_pacer
+  (input clk,
+   input reset,
+   input [7:0] rate,
+   input enable,
+   input src1_rdy_i, output dst1_rdy_o,
+   output src2_rdy_o, input dst2_rdy_i,
+   output underrun, overrun);
+
+   wire   strobe;
+   
+   cic_strober strober (.clock(clk), .reset(reset), .enable(enable),
+			.rate(rate), .strobe_fast(1), .strobe_slow(strobe));
+
+   wire   all_ready = src1_rdy_i & dst2_rdy_i;
+   assign dst1_rdy_o = all_ready & strobe;
+   assign src2_rdy_o = dst1_rdy_o;
+
+   assign underrun = strobe & ~src1_rdy_i;
+   assign overrun = strobe & ~dst2_rdy_i;
+   
+endmodule // fifo_pacer
diff --git a/usrp2/control_lib/newfifo/packet32_tb.v b/usrp2/control_lib/newfifo/packet32_tb.v
new file mode 100644
index 000000000..82bb09c29
--- /dev/null
+++ b/usrp2/control_lib/newfifo/packet32_tb.v
@@ -0,0 +1,27 @@
+
+
+module packet32_tb();
+
+   wire [35:0] data;
+   wire       src_rdy, dst_rdy;
+
+   wire       clear = 0;
+   reg 	      clk = 0;
+   reg 	      reset = 1;
+
+   always #10 clk <= ~clk;
+   initial #1000 reset <= 0;
+
+   initial $dumpfile("packet32_tb.vcd");
+   initial $dumpvars(0,packet32_tb);
+
+   wire [31:0] total, crc_err, seq_err, len_err;
+   
+   packet_generator32 pkt_gen (.clk(clk), .reset(reset), .clear(clear),
+			       .data_o(data), .src_rdy_o(src_rdy), .dst_rdy_i(dst_rdy));
+
+   packet_verifier32 pkt_ver (.clk(clk), .reset(reset), .clear(clear),
+			      .data_i(data), .src_rdy_i(src_rdy), .dst_rdy_o(dst_rdy),
+			      .total(total), .crc_err(crc_err), .seq_err(seq_err), .len_err(len_err));
+
+endmodule // packet32_tb
diff --git a/usrp2/control_lib/newfifo/packet_generator.v b/usrp2/control_lib/newfifo/packet_generator.v
new file mode 100644
index 000000000..6e8b45ccd
--- /dev/null
+++ b/usrp2/control_lib/newfifo/packet_generator.v
@@ -0,0 +1,59 @@
+
+
+module packet_generator
+  (input clk, input reset, input clear,
+   output reg [7:0] data_o, output sof_o, output eof_o, 
+   output src_rdy_o, input dst_rdy_i);
+
+   localparam len = 32'd2000;
+
+   reg [31:0] state;
+   reg [31:0] seq;
+   wire [31:0] crc_out;
+   wire        calc_crc = src_rdy_o & dst_rdy_i & ~(state[31:2] == 30'h3FFF_FFFF);
+   
+	
+   always @(posedge clk)
+     if(reset | clear)
+       seq <= 0;
+     else
+       if(eof_o & src_rdy_o & dst_rdy_i)
+	 seq <= seq + 1;
+   
+   always @(posedge clk)
+     if(reset | clear)
+       state <= 0;
+     else
+       if(src_rdy_o & dst_rdy_i)
+	 if(state == (len - 1))
+	   state <= 32'hFFFF_FFFC;
+	 else
+	   state <= state + 1;
+
+   always @*
+     case(state)
+       0 :   data_o <= len[7:0];
+       1 :   data_o <= len[15:8];
+       2 :   data_o <= len[23:16];
+       3 :   data_o <= len[31:24];
+       4 :   data_o <= seq[7:0];
+       5 :   data_o <= seq[15:8];
+       6 :   data_o <= seq[23:16];
+       7 :   data_o <= seq[31:24];
+       32'hFFFF_FFFC : data_o <= crc_out[31:24];
+       32'hFFFF_FFFD : data_o <= crc_out[23:16];
+       32'hFFFF_FFFE : data_o <= crc_out[15:8];
+       32'hFFFF_FFFF : data_o <= crc_out[7:0];
+       default : data_o <= state[7:0];
+     endcase // case (state)
+   
+   assign src_rdy_o = 1;
+   assign sof_o = (state == 0);
+   assign eof_o = (state == 32'hFFFF_FFFF);
+
+   wire        clear_crc = eof_o & src_rdy_o & dst_rdy_i;
+   
+   crc crc(.clk(clk), .reset(reset), .clear(clear_crc), .data(data_o), 
+	   .calc(calc_crc), .crc_out(crc_out), .match());
+   
+endmodule // packet_generator
diff --git a/usrp2/control_lib/newfifo/packet_generator32.v b/usrp2/control_lib/newfifo/packet_generator32.v
new file mode 100644
index 000000000..6f8004964
--- /dev/null
+++ b/usrp2/control_lib/newfifo/packet_generator32.v
@@ -0,0 +1,21 @@
+
+
+module packet_generator32
+  (input clk, input reset, input clear,
+   output [35:0] data_o, output src_rdy_o, input dst_rdy_i);
+
+   wire [7:0] 	     ll_data;
+   wire 	     ll_sof, ll_eof, ll_src_rdy, ll_dst_rdy_n;
+   
+   packet_generator pkt_gen
+     (.clk(clk), .reset(reset), .clear(clear),
+      .data_o(ll_data), .sof_o(ll_sof), .eof_o(ll_eof),
+      .src_rdy_o(ll_src_rdy), .dst_rdy_i(~ll_dst_rdy_n));
+
+   ll8_to_fifo36 ll8_to_f36
+     (.clk(clk), .reset(reset), .clear(clear),
+      .ll_data(ll_data), .ll_sof_n(~ll_sof), .ll_eof_n(~ll_eof),
+      .ll_src_rdy_n(~ll_src_rdy), .ll_dst_rdy_n(ll_dst_rdy_n),
+      .f36_data(data_o), .f36_src_rdy_o(src_rdy_o), .f36_dst_rdy_i(dst_rdy_i));
+   
+endmodule // packet_generator32
diff --git a/usrp2/control_lib/newfifo/packet_tb.v b/usrp2/control_lib/newfifo/packet_tb.v
new file mode 100644
index 000000000..3c423d2ba
--- /dev/null
+++ b/usrp2/control_lib/newfifo/packet_tb.v
@@ -0,0 +1,29 @@
+
+
+module packet_tb();
+
+   wire [7:0] data;
+   wire       sof, eof, src_rdy, dst_rdy;
+
+   wire       clear = 0;
+   reg 	      clk = 0;
+   reg 	      reset = 1;
+
+   always #10 clk <= ~clk;
+   initial #1000 reset <= 0;
+
+   initial $dumpfile("packet_tb.vcd");
+   initial $dumpvars(0,packet_tb);
+
+   wire [31:0] total, crc_err, seq_err, len_err;
+   
+   packet_generator pkt_gen (.clk(clk), .reset(reset), .clear(clear),
+			     .data_o(data), .sof_o(sof), .eof_o(eof),
+			     .src_rdy_o(src_rdy), .dst_rdy_i(dst_rdy));
+
+   packet_verifier pkt_ver (.clk(clk), .reset(reset), .clear(clear),
+			    .data_i(data), .sof_i(sof), .eof_i(eof),
+			    .src_rdy_i(src_rdy), .dst_rdy_o(dst_rdy),
+			    .total(total), .crc_err(crc_err), .seq_err(seq_err), .len_err(len_err));
+
+endmodule // packet_tb
diff --git a/usrp2/control_lib/newfifo/packet_verifier.v b/usrp2/control_lib/newfifo/packet_verifier.v
new file mode 100644
index 000000000..b49ad1bbb
--- /dev/null
+++ b/usrp2/control_lib/newfifo/packet_verifier.v
@@ -0,0 +1,61 @@
+
+
+// Packet format --
+//    Line 1 -- Length, 32 bits
+//    Line 2 -- Sequence number, 32 bits
+//    Last line -- CRC, 32 bits
+
+module packet_verifier
+  (input clk, input reset, input clear,
+   input [7:0] data_i, input sof_i, input eof_i, input src_rdy_i, output dst_rdy_o,
+
+   output reg [31:0] total, 
+   output reg [31:0] crc_err, 
+   output reg [31:0] seq_err, 
+   output reg [31:0] len_err);
+
+   reg [31:0] 	     seq_num;
+   reg [31:0] 	     length;
+   wire 	     first_byte, last_byte;
+   reg 		     second_byte, last_byte_d1;
+
+   wire 	     calc_crc = src_rdy_i & dst_rdy_o;
+   
+   crc crc(.clk(clk), .reset(reset), .clear(last_byte_d1), .data(data_i), 
+	   .calc(calc_crc), .crc_out(), .match(match_crc));
+
+   assign first_byte = src_rdy_i & dst_rdy_o & sof_i;
+   assign last_byte = src_rdy_i & dst_rdy_o & eof_i;
+   assign dst_rdy_o = ~last_byte_d1;
+
+   // stubs for now
+   wire 	     match_seq = 1;
+   wire 	     match_len = 1;
+   
+   always @(posedge clk)
+     if(reset | clear)
+       last_byte_d1 <= 0;
+     else 
+       last_byte_d1 <= last_byte;
+
+   always @(posedge clk)
+     if(reset | clear)
+       begin
+	  total <= 0;
+	  crc_err <= 0;
+	  seq_err <= 0;
+	  len_err <= 0;
+       end
+     else
+       if(last_byte_d1)
+	 begin
+	    total <= total + 1;
+	    if(~match_crc)
+	      crc_err <= crc_err + 1;
+	    else if(~match_seq)
+	      seq_err <= seq_err + 1;
+	    else if(~match_len)
+	      seq_err <= len_err + 1;
+	 end
+   
+endmodule // packet_verifier
diff --git a/usrp2/control_lib/newfifo/packet_verifier32.v b/usrp2/control_lib/newfifo/packet_verifier32.v
new file mode 100644
index 000000000..06a13d242
--- /dev/null
+++ b/usrp2/control_lib/newfifo/packet_verifier32.v
@@ -0,0 +1,30 @@
+
+
+module packet_verifier32
+  (input clk, input reset, input clear,
+   input [35:0] data_i, input src_rdy_i, output dst_rdy_o,
+   output [31:0] total, output [31:0] crc_err, output [31:0] seq_err, output [31:0] len_err);
+
+   wire [7:0] 	     ll_data;
+   wire 	     ll_sof_n, ll_eof_n, ll_src_rdy_n, ll_dst_rdy;
+   wire [35:0] 	     data_int;
+   wire 	     src_rdy_int, dst_rdy_int;
+   
+   fifo_short #(.WIDTH(36)) fifo_short
+     (.clk(clk), .reset(reset), .clear(clear),
+      .datain(data_i), .src_rdy_i(src_rdy_i), .dst_rdy_o(dst_rdy_o),
+      .dataout(data_int), .src_rdy_o(src_rdy_int), .dst_rdy_i(dst_rdy_int));
+   
+   fifo36_to_ll8 f36_to_ll8
+     (.clk(clk), .reset(reset), .clear(clear),
+      .f36_data(data_int), .f36_src_rdy_i(src_rdy_int), .f36_dst_rdy_o(dst_rdy_int),
+      .ll_data(ll_data), .ll_sof_n(ll_sof_n), .ll_eof_n(ll_eof_n),
+      .ll_src_rdy_n(ll_src_rdy_n), .ll_dst_rdy_n(~ll_dst_rdy));
+   
+   packet_verifier pkt_ver
+     (.clk(clk), .reset(reset), .clear(clear),
+      .data_i(ll_data), .sof_i(~ll_sof_n), .eof_i(~ll_eof_n),
+      .src_rdy_i(~ll_src_rdy_n), .dst_rdy_o(ll_dst_rdy),
+      .total(total), .crc_err(crc_err), .seq_err(seq_err), .len_err(len_err));
+
+endmodule // packet_verifier32
diff --git a/usrp2/control_lib/nsgpio16LE.v b/usrp2/control_lib/nsgpio16LE.v
new file mode 100644
index 000000000..8aef0c7ae
--- /dev/null
+++ b/usrp2/control_lib/nsgpio16LE.v
@@ -0,0 +1,123 @@
+// Modified from code originally by Richard Herveille, his copyright is below
+
+/////////////////////////////////////////////////////////////////////
+////                                                             ////
+////  OpenCores Simple General Purpose IO core                   ////
+////                                                             ////
+////  Author: Richard Herveille                                  ////
+////          richard@asics.ws                                   ////
+////          www.asics.ws                                       ////
+////                                                             ////
+/////////////////////////////////////////////////////////////////////
+////                                                             ////
+//// Copyright (C) 2002 Richard Herveille                        ////
+////                    richard@asics.ws                         ////
+////                                                             ////
+//// This source file may be used and distributed without        ////
+//// restriction provided that this copyright statement is not   ////
+//// removed from the file and that any derivative work contains ////
+//// the original copyright notice and the associated disclaimer.////
+////                                                             ////
+////     THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY     ////
+//// EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED   ////
+//// TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS   ////
+//// FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL THE AUTHOR      ////
+//// OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,         ////
+//// INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES    ////
+//// (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE   ////
+//// GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR        ////
+//// BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF  ////
+//// LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT  ////
+//// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT  ////
+//// OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE         ////
+//// POSSIBILITY OF SUCH DAMAGE.                                 ////
+////                                                             ////
+/////////////////////////////////////////////////////////////////////
+
+
+module nsgpio16LE
+  (input clk_i, input rst_i, 
+   input cyc_i, input stb_i, input [3:0] adr_i, input we_i, input [15:0] dat_i, 
+   output reg [15:0] dat_o, output reg ack_o,
+   input [31:0] atr, input [31:0] debug_0, input [31:0] debug_1, 
+   inout [31:0] gpio
+   );
+
+   reg [31:0] 	ctrl, line, ddr, dbg, lgpio;
+   
+   wire 	wb_acc = cyc_i & stb_i;            // WISHBONE access
+   wire 	wb_wr  = wb_acc & we_i;            // WISHBONE write access
+
+   always @(posedge clk_i or posedge rst_i)
+     if (rst_i)
+       begin
+          ctrl <= 32'h0;
+          line <= 32'h0;
+	  ddr <= 32'h0;
+	  dbg <= 32'h0;
+       end
+     else if (wb_wr)
+       case( adr_i[3:1] )
+	 3'b000 : 
+           line[15:0] <= dat_i;
+	 3'b001 : 
+           line[31:16] <= dat_i;
+	 3'b010 :
+	   ddr[15:0] <= dat_i;
+	 3'b011 :
+	   ddr[31:16] <= dat_i;
+	 3'b100 :
+	   ctrl[15:0] <= dat_i;
+	 3'b101 :
+	   ctrl[31:16] <= dat_i;
+	 3'b110 :
+	   dbg[15:0] <= dat_i;
+	 3'b111 :
+	   dbg[31:16] <= dat_i;
+       endcase // case ( adr_i[3:1] )
+   
+   always @(posedge clk_i)
+     case (adr_i[3:1])
+       3'b000 :
+	 dat_o <= lgpio[15:0];
+       3'b001 :
+	 dat_o <= lgpio[31:16];
+       3'b010 :
+	 dat_o <= ddr[15:0];
+       3'b011 :
+	 dat_o <= ddr[31:16];
+       3'b100 :
+	 dat_o <= ctrl[15:0];
+       3'b101 :
+	 dat_o <= ctrl[31:16];
+       3'b110 :
+	 dat_o <= dbg[15:0];
+       3'b111 :
+	 dat_o <= dbg[31:16];
+     endcase // case (adr_i[3:1])
+   
+   
+   always @(posedge clk_i or posedge rst_i)
+     if (rst_i)
+       ack_o <= 1'b0;
+     else
+       ack_o <= wb_acc & !ack_o;
+   
+   // latch GPIO input pins
+   always @(posedge clk_i)
+     lgpio <= gpio;
+   
+   // assign GPIO outputs
+   integer   n;
+   reg [31:0] igpio; // temporary internal signal
+   
+   always @(ctrl or line or debug_1 or debug_0 or atr or ddr or dbg)
+     for(n=0;n<32;n=n+1)
+       igpio[n] <= ddr[n] ? (dbg[n] ? (ctrl[n] ? debug_1[n] : debug_0[n]) : 
+			     (ctrl[n] ?  atr[n] : line[n]) )
+	 : 1'bz;
+   
+   assign     gpio = igpio;
+   
+endmodule
+
diff --git a/usrp2/control_lib/ram_2port_mixed_width.v b/usrp2/control_lib/ram_2port_mixed_width.v
new file mode 100644
index 000000000..fae7d8de3
--- /dev/null
+++ b/usrp2/control_lib/ram_2port_mixed_width.v
@@ -0,0 +1,120 @@
+
+module ram_2port_mixed_width
+  (input clk16,
+   input en16,
+   input we16,
+   input [10:0] addr16,
+   input [15:0] di16,
+   output [15:0] do16,
+   input clk32,
+   input en32,
+   input we32,
+   input [9:0] addr32,
+   input [31:0] di32,
+   output [31:0] do32);
+
+   wire 	 en32a = en32 & ~addr32[9];
+   wire 	 en32b = en32 & addr32[9];
+   wire 	 en16a = en16 & ~addr16[10];
+   wire 	 en16b = en16 & addr16[10];
+
+   wire [31:0] 	 do32a, do32b;
+   wire [15:0] 	 do16a, do16b;
+   
+   assign do32 = addr32[9] ? do32b : do32a;
+   assign do16 = addr16[10] ? do16b : do16a;
+   
+   RAMB16BWE_S36_S18 #(.INIT_A(36'h000000000),
+		       .INIT_B(18'h00000),
+		       .SIM_COLLISION_CHECK("ALL"), // "NONE", "WARNING_ONLY", "GENERATE_X_ONLY", "ALL"
+		       .SRVAL_A(36'h000000000), // Port A output value upon SSR assertion
+		       .SRVAL_B(18'h00000),      // Port B output value upon SSR assertion
+		       .WRITE_MODE_A("WRITE_FIRST"), // WRITE_FIRST, READ_FIRST or NO_CHANGE
+		       .WRITE_MODE_B("WRITE_FIRST") // WRITE_FIRST, READ_FIRST or NO_CHANGE
+		       ) 
+   RAMB16BWE_S36_S18_0 (.DOA(do32a),       // Port A 32-bit Data Output
+			.DOB(do16a),       // Port B 16-bit Data Output
+			.DOPA(),     // Port A 4-bit Parity Output
+			.DOPB(),     // Port B 2-bit Parity Output
+			.ADDRA(addr32[8:0]),   // Port A 9-bit Address Input
+			.ADDRB(addr16[9:0]),   // Port B 10-bit Address Input
+			.CLKA(clk32),     // Port A 1-bit Clock
+			.CLKB(clk16),     // Port B 1-bit Clock
+			.DIA(di32),       // Port A 32-bit Data Input
+			.DIB(di16),       // Port B 16-bit Data Input
+			.DIPA(0),     // Port A 4-bit parity Input
+			.DIPB(0),     // Port-B 2-bit parity Input
+			.ENA(en32a),       // Port A 1-bit RAM Enable Input
+			.ENB(en16a),       // Port B 1-bit RAM Enable Input
+			.SSRA(0),     // Port A 1-bit Synchronous Set/Reset Input
+			.SSRB(0),     // Port B 1-bit Synchronous Set/Reset Input
+			.WEA({4{we32}}),       // Port A 4-bit Write Enable Input
+			.WEB({2{we16}})        // Port B 2-bit Write Enable Input
+			);
+
+   RAMB16BWE_S36_S18 #(.INIT_A(36'h000000000),
+		       .INIT_B(18'h00000),
+		       .SIM_COLLISION_CHECK("ALL"), // "NONE", "WARNING_ONLY", "GENERATE_X_ONLY", "ALL"
+		       .SRVAL_A(36'h000000000), // Port A output value upon SSR assertion
+		       .SRVAL_B(18'h00000),      // Port B output value upon SSR assertion
+		       .WRITE_MODE_A("WRITE_FIRST"), // WRITE_FIRST, READ_FIRST or NO_CHANGE
+		       .WRITE_MODE_B("WRITE_FIRST") // WRITE_FIRST, READ_FIRST or NO_CHANGE
+		       ) 
+   RAMB16BWE_S36_S18_1 (.DOA(do32b),       // Port A 32-bit Data Output
+			.DOB(do16b),       // Port B 16-bit Data Output
+			.DOPA(),     // Port A 4-bit Parity Output
+			.DOPB(),     // Port B 2-bit Parity Output
+			.ADDRA(addr32[8:0]),   // Port A 9-bit Address Input
+			.ADDRB(addr16[9:0]),   // Port B 10-bit Address Input
+			.CLKA(clk32),     // Port A 1-bit Clock
+			.CLKB(clk16),     // Port B 1-bit Clock
+			.DIA(di32),       // Port A 32-bit Data Input
+			.DIB(di16),       // Port B 16-bit Data Input
+			.DIPA(0),     // Port A 4-bit parity Input
+			.DIPB(0),     // Port-B 2-bit parity Input
+			.ENA(en32b),       // Port A 1-bit RAM Enable Input
+			.ENB(en16b),       // Port B 1-bit RAM Enable Input
+			.SSRA(0),     // Port A 1-bit Synchronous Set/Reset Input
+			.SSRB(0),     // Port B 1-bit Synchronous Set/Reset Input
+			.WEA({4{we32}}),       // Port A 4-bit Write Enable Input
+			.WEB({2{we16}})        // Port B 2-bit Write Enable Input
+			);
+
+endmodule // ram_2port_mixed_width
+
+
+
+   
+// ISE 10.1.03 chokes on the following
+   
+/*
+   
+   reg [31:0] 	       ram [(1<<AWIDTH)-1:0];
+   integer 	       i;
+   initial
+     for(i=0;i<512;i=i+1)
+       ram[i] <= 32'b0;
+   
+   always @(posedge clk16)
+     if (en16)
+       begin
+          if (we16)
+            if(addr16[0])
+	      ram[addr16[10:1]][15:0] <= di16;
+	    else
+	      ram[addr16[10:1]][31:16] <= di16;
+	  do16 <= addr16[0] ? ram[addr16[10:1]][15:0] : ram[addr16[10:1]][31:16];
+       end
+
+   always @(posedge clk32)
+     if (en32)
+       begin
+          if (we32)
+            ram[addr32] <= di32;
+          do32 <= ram[addr32];
+       end
+
+endmodule // ram_2port_mixed_width
+
+ 
+ */
diff --git a/usrp2/control_lib/settings_bus.v b/usrp2/control_lib/settings_bus.v
index fc960e456..aec179516 100644
--- a/usrp2/control_lib/settings_bus.v
+++ b/usrp2/control_lib/settings_bus.v
@@ -10,7 +10,7 @@ module settings_bus
      input wb_stb_i,
      input wb_we_i,
      output reg wb_ack_o,
-     output strobe,
+     output reg strobe,
      output reg [7:0] addr,
      output reg [31:0] data);
 
@@ -19,18 +19,18 @@ module settings_bus
    always @(posedge wb_clk)
      if(wb_rst)
        begin
-	  stb_int <= 1'b0;
+	  strobe <= 1'b0;
 	  addr <= 8'd0;
 	  data <= 32'd0;
        end
-     else if(wb_we_i & wb_stb_i)
+     else if(wb_we_i & wb_stb_i & ~wb_ack_o)
        begin
-	  stb_int <= 1'b1;
+	  strobe <= 1'b1;
 	  addr <= wb_adr_i[9:2];
 	  data <= wb_dat_i;
        end
      else
-       stb_int <= 1'b0;
+       strobe <= 1'b0;
 
    always @(posedge wb_clk)
      if(wb_rst)
@@ -38,11 +38,4 @@ module settings_bus
      else
        wb_ack_o <= wb_stb_i & ~wb_ack_o;
 
-   always @(posedge wb_clk)
-     stb_int_d1 <= stb_int;
-
-   //assign strobe = stb_int & ~stb_int_d1;
-   assign strobe = stb_int & wb_ack_o;
-          
 endmodule // settings_bus
-
diff --git a/usrp2/control_lib/settings_bus_16LE.v b/usrp2/control_lib/settings_bus_16LE.v
new file mode 100644
index 000000000..76061e9e0
--- /dev/null
+++ b/usrp2/control_lib/settings_bus_16LE.v
@@ -0,0 +1,54 @@
+
+// Grab settings off the wishbone bus, send them out to settings bus
+// 16 bits little endian, but all registers need to be written 32 bits at a time.
+// This means that you write the low 16 bits first and then the high 16 bits.
+// The setting regs are strobed when the high 16 bits are written
+
+module settings_bus_16LE
+  #(parameter AWIDTH=16, RWIDTH=8)
+    (input wb_clk, 
+     input wb_rst, 
+     input [AWIDTH-1:0] wb_adr_i,
+     input [15:0] wb_dat_i,
+     input wb_stb_i,
+     input wb_we_i,
+     output reg wb_ack_o,
+     output strobe,
+     output reg [7:0] addr,
+     output reg [31:0] data);
+
+   reg 		       stb_int;
+   
+   always @(posedge wb_clk)
+     if(wb_rst)
+       begin
+	  stb_int <= 1'b0;
+	  addr <= 8'd0;
+	  data <= 32'd0;
+       end
+     else if(wb_we_i & wb_stb_i)
+       begin
+	  addr <= wb_adr_i[RWIDTH+1:2];  // Zero pad high bits
+	  if(wb_adr_i[1])
+	    begin
+	       stb_int <= 1'b1;     // We now have both halves
+	       data[31:16] <= wb_dat_i;
+	    end
+	  else
+	    begin
+	       stb_int <= 1'b0;     // Don't strobe, we need other half
+	       data[15:0] <= wb_dat_i;
+	    end
+       end
+     else
+       stb_int <= 1'b0;
+
+   always @(posedge wb_clk)
+     if(wb_rst)
+       wb_ack_o <= 0;
+     else
+       wb_ack_o <= wb_stb_i & ~wb_ack_o;
+
+   assign strobe = stb_int & wb_ack_o;
+          
+endmodule // settings_bus_16LE
diff --git a/usrp2/control_lib/simple_uart.v b/usrp2/control_lib/simple_uart.v
index 22f0e70a2..0dd58b5f5 100644
--- a/usrp2/control_lib/simple_uart.v
+++ b/usrp2/control_lib/simple_uart.v
@@ -1,11 +1,12 @@
 
 module simple_uart
   #(parameter TXDEPTH = 1,
-    parameter RXDEPTH = 1)
-    (input clk_i, input rst_i,
-     input we_i, input stb_i, input cyc_i, output reg ack_o,
-     input [2:0] adr_i, input [31:0] dat_i, output reg [31:0] dat_o,
-     output rx_int_o, output tx_int_o, output tx_o, input rx_i, output baud_o);
+    parameter RXDEPTH = 1,
+    parameter CLKDIV_DEFAULT = 16'd0)
+   (input clk_i, input rst_i,
+    input we_i, input stb_i, input cyc_i, output reg ack_o,
+    input [2:0] adr_i, input [31:0] dat_i, output reg [31:0] dat_o,
+    output rx_int_o, output tx_int_o, output tx_o, input rx_i, output baud_o);
    
    // Register Map
    localparam SUART_CLKDIV = 0;
@@ -30,7 +31,7 @@ module simple_uart
    
    always @(posedge clk_i)
      if (rst_i)
-       clkdiv <= 0;
+       clkdiv <= CLKDIV_DEFAULT;
      else if (wb_wr)
        case(adr_i)
 	 SUART_CLKDIV : clkdiv <= dat_i[15:0];