uhd: Removed drivers for E100/E110

The E1x0 series is still supported on the 3.9 LTS branch.

1 files changed, 0 insertions, 136 deletions

diff --git a/host/docs/usrp_e1x0.dox b/host/docs/usrp_e1x0.dox
deleted file mode 100644
index 553d437c7..000000000
--- a/host/docs/usrp_e1x0.dox
+++ /dev/null
@@ -1,136 +0,0 @@
-/*! \page page_usrp_e1x0 USRP-E1x0 Series
-
-\tableofcontents
-
-\section e1x0_features Comparative features list
-
-- Hardware Capabilities:
-    -   1 transceiver card slot
-    -   Internal PPS reference input
-    -   Internal 10 MHz reference input
-    -   Configurable clock rate (defaults to 64 MHz)
-    -   Internal GPSDO option
-- FPGA Capabilities:
-    -   2 RX DDC chains in FPGA
-    -   1 TX DUC chain in FPGA
-    -   Timed commands in FPGA
-    -   Timed sampling in FPGA
-    -   sc8 and sc16 sample modes
-        -   Up to 8 MHz of RF BW with 16-bit samples
-        -   Up to 16 MHz of RF BW with 8-bit samples
-
-\section e1x0_imgs Specify a Non-standard Image
-
-UHD software will automatically select the USRP-Embedded FPGA image from
-the installed images package. The FPGA image selection can be overridden
-with the `fpga` device address parameter.
-
-Example device address string representations to specify non-standard
-FPGA image:
-
-    fpga=usrp_e100_custom.bin
-
-\section e1x0_mcr Changing the Master Clock Rate
-
-The master clock rate of the USRP-Embedded feeds both the FPGA DSP and
-the codec chip. Hundreds of rates between 32 MHz and 64 MHz are
-available. A few notable rates are:
-
--   **64 MHz:** maximum rate of the codec chip
--   **61.44 MHz:** good for UMTS/WCDMA applications
--   **52 MHz:** good for GSM applications
-
-\subsection e1x0_mcr_extvcxo Set 61.44MHz - uses external VCXO
-
-To use the 61.44 MHz clock rate with the USRP-Embedded, two jumpers must
-be moved on the device.
-
--   **J16** is a two pin header; remove the jumper (or leave it on pin1
-    only).
--   **J15** is a three pin header; move the jumper to (pin1, pin2).
-
-**Note:** See instructions below to communicate the desired clock rate
-to UHD software.
-
-\subsection e1x0_intvco Set other rates - uses internal VCO
-
-To use other clock rates, the jumpers will need to be in the default
-position.
-
--   **J16** is a two pin header; move the jumper to (pin1, pin2).
--   **J15** is a three pin header; move the jumper to (pin2, pin3).
-
-To communicate the desired clock rate into UHD software, specify the a
-special device address argument, where the key is
-`master_clock_rate` and the value is a rate in Hz. Example:
-
-    uhd_usrp_probe --args="master_clock_rate=52e6"
-
-\section e1x0_clksync Clock Synchronization
-
-\subsection e1x0_clksync_ref Ref Clock - 10MHz
-
-The E1xx has a 10MHz TCXO which can be used to discipline the flexible
-clocking by selecting `REF_INT` for the uhd::clock_config_t.
-
-Alternately, an external 10MHz reference clock can be supplied by
-soldering a connector.
-
--   Connector **J10** (REF_IN) needs MCX connector **WM5541-ND** or
-    similar.
--   Square wave will offer the best phase noise performance, but
-    sinusoid is acceptable.
--   **Power level:** 0 to 15dBm
--   Select `REF_SMA` in uhd::clock_config_t.
-
-\subsection e1x0_clksync_pps PPS - Pulse Per Second
-
-An external PPS signal for timestamp synchronization can be supplied by
-soldering a connector.
-
--   Connector **J13** (PPS) needs MCX connector **WM5541-ND** or
-    similar.
--   Requires a square wave signal.
--   **Amplitude:** 3.3 to 5 Vpp
-
-Test the PPS input with the following app (`<args>` are device
-address arguments, optional if only one USRP device is on your machine):
-
-    cd <install-path>/lib/uhd/examples
-    ./test_pps_input --args=<args>
-
-\subsection e1x0_clksync_gpsdo Internal GPSDO
-
-Please see the \subpage page_gpsdo for
-information on configuring and using the internal GPSDO.
-
-UHD software will always try to detect an installed GPSDO at runtime. It
-is not necessary to burn a special EEPROM value for GPSDO detection.
-
-\section e1x0_hw Hardware Setup Notes
-
-\subsection e1x0_hw_leds Front panel LEDs
-
-The LEDs on the front panel can be useful in debugging hardware and
-software issues. The LEDs reveal the following about the state of the
-device:
-
--   **LED A:** transmitting
--   **LED B:** PPS signal
--   **LED C:** receiving
--   **LED D:** FPGA loaded
--   **LED E:** reference lock
--   **LED F:** board power
-
-\section e1x0_misc Miscellaneous
-
-\subsection e1x0_misc_sensors Available Sensors
-
-The following sensors are available; they can be queried through the
-API.
-
--   **ref_locked:** clock reference locked (internal/external)
--   other sensors are added when the GPSDO is enabled
-
-*/
-// vim:ft=doxygen: