docs: Moved manual to Doxygen

1 files changed, 0 insertions, 107 deletions

diff --git a/host/docs/usrp_b100.rst b/host/docs/usrp_b100.rst
deleted file mode 100644
index 223ad5a90..000000000
--- a/host/docs/usrp_b100.rst
+++ /dev/null
@@ -1,107 +0,0 @@
-========================================================================
-UHD - USRP-B100 Series Device Manual
-========================================================================
-
-.. contents:: Table of Contents
-
-------------------------------------------------------------------------
-Comparative features list
-------------------------------------------------------------------------
-
-**Hardware Capabilities:**
- * 1 transceiver card slot
- * External PPS reference input
- * External 10 MHz reference input
- * Configurable clock rate (defaults 64 MHz)
-
-**FPGA Capabilities:**
- * 1 RX DDC chain in FPGA
- * 1 TX DUC chain in FPGA
- * Timed commands in FPGA
- * Timed sampling in FPGA
- * sc8 and sc16 sample modes
-
-   * Up to 8 MHz of RF BW with 16-bit samples
-   * Up to 16 MHz of RF BW with 8-bit samples
-
-------------------------------------------------------------------------
-Specify a Non-standard Image
-------------------------------------------------------------------------
-UHD software will automatically select the USRP B100 images from the installed images package.
-The image selection can be overridden with the **--fpga=** and **--fw=** device address parameters.
-
-Example device address string representations to specify non-standard images:
-
-::
-
-    fpga=usrp_b100_fpga_2rx.bin
-
-    -- OR --
-
-    fw=usrp_b100_fw.ihx
-
-------------------------------------------------------------------------
-Changing the Master Clock Rate
-------------------------------------------------------------------------
-The master clock rate of the B100 feeds both the FPGA DSP and the codec chip.
-Hundreds of rates between 32 MHz and 64 MHz are available.
-A few notable rates are:
-
-* **64 MHz:** maximum rate of the codec chip
-* **61.44 MHz:** good for UMTS/WCDMA applications
-* **52 MHz:** good for GSM applications
-
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-Set 61.44 MHz - uses external VCXO
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-To use the 61.44 MHz clock rate, the USRP embedded will require one jumper to be moved,
-and X4 must be populated with a 61.44 MHz oscillator.
-
-* **J15** is a three pin header, move the jumper to (pin1, pin2)
-* **357LB3I061M4400** is the recommended oscillator for X4
-
-**Note:** See instructions below to communicate the desired clock rate into UHD software.
-
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-Set other rates - uses internal VCO
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-To use other clock rates, the jumper will need to be in the default position.
-
-* **J15** is a three pin header, move the jumper to (pin2, pin3)
-
-To communicate the desired clock rate into UHD software,
-specify the special device address argument,
-where the key is **master_clock_rate** and the value is a rate in Hz.
-Example:
-::
-
-    uhd_usrp_probe --args="master_clock_rate=52e6"
-
-------------------------------------------------------------------------
-Hardware setup notes
-------------------------------------------------------------------------
-
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-Front panel LEDs
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-The LEDs on the front panel can be useful in debugging hardware and software issues.
-The LEDs reveal the following about the state of the device:
-
-* **LED A:** transmitting
-* **LED B:** FPGA loaded
-* **LED C:** receiving
-* **LED D:** FPGA loaded
-* **LED E:** reference lock
-* **LED F:** board power
-
-------------------------------------------------------------------------
-Miscellaneous
-------------------------------------------------------------------------
-
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-Available Sensors
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-The following sensors are available;
-they can be queried through the API.
-
-* **ref_locked:** clock reference locked (internal/external)