Merge branch 'fpga_next' into next

53 files changed, 2487 insertions, 1070 deletions

diff --git a/fpga/usrp2/control_lib/Makefile.srcs b/fpga/usrp2/control_lib/Makefile.srcs
index 567feacde..6ee7ea262 100644
--- a/fpga/usrp2/control_lib/Makefile.srcs
+++ b/fpga/usrp2/control_lib/Makefile.srcs
@@ -1,5 +1,5 @@
 #
-# Copyright 2010 Ettus Research LLC
+# Copyright 2010-2012 Ettus Research LLC
 #
 
 ##################################################
@@ -54,4 +54,5 @@ settings_bus_16LE.v \
 atr_controller16.v \
 fifo_to_wb.v \
 gpio_atr.v \
+user_settings.v \
 ))
diff --git a/fpga/usrp2/control_lib/double_buffer_tb.v b/fpga/usrp2/control_lib/double_buffer_tb.v
index a9aae6956..804e8804d 100644
--- a/fpga/usrp2/control_lib/double_buffer_tb.v
+++ b/fpga/usrp2/control_lib/double_buffer_tb.v
@@ -27,7 +27,7 @@ module double_buffer_tb();
    reg src_rdy_i = 0;
    wire dst_rdy_o;
    
-   wire dst_rdy_i = 1;
+   wire dst_rdy_i = 0;
    wire [35:0] data_o;
    reg [35:0]  data_i;
 
@@ -46,9 +46,9 @@ module double_buffer_tb();
       .data_i(data_i), .src_rdy_i(src_rdy_i), .dst_rdy_o(dst_rdy_o),
       .data_o(data_o), .src_rdy_o(src_rdy_o), .dst_rdy_i(dst_rdy_i));
 
-   dspengine_16to8 dspengine_16to8
+   dspengine_8to16 #(.HEADER_OFFSET(1)) dspengine_8to16
      (.clk(clk),.reset(rst),.clear(0),
-      .set_stb(set_stb), .set_addr(0), .set_data({13'h0,1'b1,18'h00400}),
+      .set_stb(set_stb), .set_addr(0), .set_data(1),
       .access_we(access_we), .access_stb(access_stb), .access_ok(access_ok), .access_done(access_done), 
       .access_skip_read(access_skip_read), .access_adr(access_adr), .access_len(access_len), 
       .access_dat_i(buf_to_dsp), .access_dat_o(dsp_to_buf));
@@ -69,11 +69,13 @@ module double_buffer_tb();
 	@(posedge clk);
 	@(posedge clk);
 	@(posedge clk);
-
+/*
 	// Passthrough
 	$display("Passthrough");
 	src_rdy_i <= 1;
-	data_i <= { 2'b00,1'b0,1'b1,32'hFFFFFFFF};
+	data_i <= { 2'b00,1'b0,1'b1,32'h01234567};
+	@(posedge clk);
+	data_i <= { 2'b00,1'b0,1'b0,32'hFFFFFFFF};
 	@(posedge clk);
 	data_i <= { 2'b00,1'b0,1'b0,32'h04050607};
 	@(posedge clk);
@@ -86,16 +88,18 @@ module double_buffer_tb();
 
 	repeat (5)
 	  @(posedge clk);
-
+*/
 	$display("Enabled");
 	set_stb <= 1;
 	@(posedge clk);
 	set_stb <= 0;
-
+/*
 	@(posedge clk);
 	$display("Non-IF Data Passthrough");
 	src_rdy_i <= 1;
-	data_i <= { 2'b00,1'b0,1'b1,32'hC0000000};
+	data_i <= { 2'b00,1'b0,1'b1,32'h89acdef0};
+	@(posedge clk);
+	data_i <= { 2'b00,1'b0,1'b0,32'hC0000000};
 	@(posedge clk);
 	data_i <= { 2'b00,1'b0,1'b0,32'h14151617};
 	@(posedge clk);
@@ -111,7 +115,9 @@ module double_buffer_tb();
 	
 	$display("No StreamID, No Trailer, Even");
 	src_rdy_i <= 1;
-  	data_i <= { 2'b00,1'b0,1'b1,32'h0000FFFF};
+  	data_i <= { 2'b00,1'b0,1'b1,32'hAAAAAAAA};
+	@(posedge clk);
+  	data_i <= { 2'b00,1'b0,1'b0,32'h0000FFFF};
 	@(posedge clk);
 	data_i <= { 2'b00,1'b0,1'b0,32'h01000200};
 	@(posedge clk);
@@ -139,7 +145,9 @@ module double_buffer_tb();
 
 	$display("No StreamID, No Trailer, Odd");
 	src_rdy_i <= 1;
-  	data_i <= { 2'b00,1'b0,1'b1,32'h0000FFFF};
+  	data_i <= { 2'b00,1'b0,1'b1,32'hBBBBBBBB};
+	@(posedge clk);
+  	data_i <= { 2'b00,1'b0,1'b0,32'h0000FFFF};
 	@(posedge clk);
 	data_i <= { 2'b00,1'b0,1'b0,32'h11001200};
 	@(posedge clk);
@@ -159,30 +167,59 @@ module double_buffer_tb();
 
 	while(~dst_rdy_o)
 	  @(posedge clk);
-
+*/
+   /*
 	$display("No StreamID, Trailer, Even");
 	src_rdy_i <= 1;
-  	data_i <= { 2'b00,1'b0,1'b1,32'h0400FFFF};
+  	data_i <= { 2'b00,1'b0,1'b1,32'hCCCCCCCC};
 	@(posedge clk);
-	data_i <= { 2'b00,1'b0,1'b0,32'h21002200};
+  	data_i <= { 2'b00,1'b0,1'b0,32'h0400FFFF};
 	@(posedge clk);
-	data_i <= { 2'b00,1'b0,1'b0,32'h23002400};
+	data_i <= { 2'b00,1'b0,1'b0,32'h21222324};
+	@(posedge clk);
+	data_i <= { 2'b00,1'b0,1'b0,32'h25262728};
 	src_rdy_i <= 0;
 	@(posedge clk);
 	src_rdy_i <= 1;
 	@(posedge clk);
-	data_i <= { 2'b00,1'b0,1'b0,32'h25002600};
+	data_i <= { 2'b00,1'b0,1'b0,32'h292a2b2c};
 	@(posedge clk);
-	data_i <= { 2'b00,1'b0,1'b0,32'h27002800};
+	data_i <= { 2'b00,1'b0,1'b0,32'h2d2e2f30};
 	@(posedge clk);
-	data_i <= { 2'b00,1'b1,1'b0,32'h29002a00};
+	data_i <= { 2'b00,1'b1,1'b0,32'hDEADBEEF};
 	@(posedge clk);
 	src_rdy_i <= 0;
 	@(posedge clk);
-
+*/
+	while(~dst_rdy_o)
+	  @(posedge clk);
+/*
+	$display("No StreamID, Trailer, Odd");
+	src_rdy_i <= 1;
+  	data_i <= { 2'b00,1'b0,1'b1,32'hDDDDDDDD};
+	@(posedge clk);
+  	data_i <= { 2'b00,1'b0,1'b0,32'h0400FFFF};
+	@(posedge clk);
+	data_i <= { 2'b00,1'b0,1'b0,32'h21222324};
+	@(posedge clk);
+	data_i <= { 2'b00,1'b0,1'b0,32'h25262728};
+	src_rdy_i <= 0;
+	@(posedge clk);
+	src_rdy_i <= 1;
+	@(posedge clk);
+	data_i <= { 2'b00,1'b0,1'b0,32'h292a2b2c};
+	@(posedge clk);
+	data_i <= { 2'b00,1'b0,1'b0,32'h2d2e2f30};
+	@(posedge clk);
+	data_i <= { 2'b00,1'b1,1'b0,32'hDEBDBF0D};
+	@(posedge clk);
+	src_rdy_i <= 0;
+	@(posedge clk);
+*/
 	while(~dst_rdy_o)
 	  @(posedge clk);
 
+/*
 	$display("No StreamID, Trailer, Odd");
 	src_rdy_i <= 1;
   	data_i <= { 2'b00,1'b0,1'b1,32'h0400FFFF};
@@ -226,23 +263,45 @@ module double_buffer_tb();
 
 	while(~dst_rdy_o)
 	  @(posedge clk);
-
+*/
 	$display("StreamID, Trailer, Odd");
 	src_rdy_i <= 1;
-  	data_i <= { 2'b00,1'b0,1'b1,32'h1400FFFF};
+  	data_i <= { 2'b00,1'b0,1'b1,32'hABCDEF98};
+	@(posedge clk);
+  	data_i <= { 2'b00,1'b0,1'b0,32'h1c034567};
+	@(posedge clk);
+	data_i <= { 2'b00,1'b0,1'b0,32'ha0a1a2a3};
+	@(posedge clk);
+	data_i <= { 2'b00,1'b0,1'b0,32'ha4a5a6a7};
+//	src_rdy_i <= 0;
+//	@(posedge clk);
+//	src_rdy_i <= 1;
+	@(posedge clk);
+	data_i <= { 2'b00,1'b0,1'b0,32'ha8a9aaab};
 	@(posedge clk);
-	data_i <= { 2'b00,1'b0,1'b0,32'ha100a200};
+	data_i <= { 2'b00,1'b0,1'b0,32'hacadaeaf};
+	@(posedge clk);
+	data_i <= { 2'b00,1'b1,1'b0,32'hdeadbeef};
 	@(posedge clk);
-	data_i <= { 2'b00,1'b0,1'b0,32'ha300a400};
 	src_rdy_i <= 0;
 	@(posedge clk);
 	src_rdy_i <= 1;
+  	data_i <= { 2'b00,1'b0,1'b1,32'hABCDEF98};
+	@(posedge clk);
+  	data_i <= { 2'b00,1'b0,1'b0,32'h1c034567};
+	@(posedge clk);
+	data_i <= { 2'b00,1'b0,1'b0,32'ha0a1a2a3};
+	@(posedge clk);
+	data_i <= { 2'b00,1'b0,1'b0,32'ha4a5a6a7};
+//	src_rdy_i <= 0;
+//	@(posedge clk);
+//	src_rdy_i <= 1;
 	@(posedge clk);
-	data_i <= { 2'b00,1'b0,1'b0,32'ha500a600};
+	data_i <= { 2'b00,1'b0,1'b0,32'ha8a9aaab};
 	@(posedge clk);
-	data_i <= { 2'b00,1'b0,1'b0,32'ha700a800};
+	data_i <= { 2'b00,1'b0,1'b0,32'hacadaeaf};
 	@(posedge clk);
-	data_i <= { 2'b00,1'b1,1'b0,32'hbbb0bbb0};
+	data_i <= { 2'b00,1'b1,1'b0,32'hdeadbeef};
 	@(posedge clk);
 	src_rdy_i <= 0;
 	@(posedge clk);
diff --git a/fpga/usrp2/control_lib/user_settings.v b/fpga/usrp2/control_lib/user_settings.v
new file mode 100644
index 000000000..d87f1de21
--- /dev/null
+++ b/fpga/usrp2/control_lib/user_settings.v
@@ -0,0 +1,63 @@
+//
+// Copyright 2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+// User settings bus
+//
+// Provides 8-bit address, 32-bit data write only bus for user settings, consumes to addresses in
+// normal settings bus.
+//
+// Write user address to BASE
+// Write user data to BASE+1
+//
+// The user_set_stb will strobe after data write, must write new address even if same as previous one.
+
+module user_settings
+  #(parameter BASE=0)
+  (input clk,
+   input rst,
+
+   input         set_stb,
+   input [7:0]   set_addr,
+   input [31:0]  set_data,
+
+   output        set_stb_user,
+   output [7:0]  set_addr_user,
+   output [31:0] set_data_user
+   );
+
+   wire 	 addr_changed, data_changed;
+   reg 		 stb_int;
+   
+   setting_reg #(.my_addr(BASE+0),.width(8)) sr_0
+     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
+      .in(set_data),.out(set_addr_user),.changed(addr_changed) );
+   
+   setting_reg #(.my_addr(BASE+1)) sr_1
+     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
+      .in(set_data),.out(set_data_user),.changed(data_changed) );
+   
+   always @(posedge clk)
+     if (rst|set_stb_user)
+       stb_int <= 0;
+     else
+       if (addr_changed)
+         stb_int <= 1;
+   
+   assign set_stb_user = stb_int & data_changed;
+   
+endmodule // user_settings
+
diff --git a/fpga/usrp2/custom/custom_dsp_rx.v b/fpga/usrp2/custom/custom_dsp_rx.v
new file mode 100644
index 000000000..355adf008
--- /dev/null
+++ b/fpga/usrp2/custom/custom_dsp_rx.v
@@ -0,0 +1,71 @@
+//
+// Copyright 2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+//COPY ME, CUSTOMIZE ME...
+
+//The following module effects the IO of the DDC chain.
+//By default, this entire module is a simple pass-through.
+
+//To implement DSP logic before the DDC:
+//Implement custom DSP between frontend and ddc input.
+
+//To implement DSP logic after the DDC:
+//Implement custom DSP between ddc output and baseband.
+
+//To bypass the DDC with custom logic:
+//Implement custom DSP between frontend and baseband.
+
+module custom_dsp_rx
+#(
+    //frontend bus width
+    parameter WIDTH = 24
+)
+(
+    //control signals
+    input clock, //dsp clock
+    input reset, //active high synchronous reset
+    input clear, //active high on packet control init
+    input enable, //active high when streaming enabled
+
+    //user settings bus, controlled through user setting regs API
+    input set_stb, input [7:0] set_addr, input [31:0] set_data,
+
+    //full rate inputs directly from the RX frontend
+    input [WIDTH-1:0] frontend_i,
+    input [WIDTH-1:0] frontend_q,
+
+    //full rate outputs directly to the DDC chain
+    output [WIDTH-1:0] ddc_in_i,
+    output [WIDTH-1:0] ddc_in_q,
+
+    //strobed samples {I16,Q16} from the RX DDC chain
+    input [31:0] ddc_out_sample,
+    input ddc_out_strobe, //high on valid sample
+    output ddc_out_enable, //enables DDC module
+
+    //strobbed baseband samples {I16,Q16} from this module
+    output [31:0] bb_sample,
+    output bb_strobe //high on valid sample
+);
+
+    assign ddc_in_i = frontend_i;
+    assign ddc_in_q = frontend_q;
+    assign bb_sample = ddc_out_sample;
+    assign bb_strobe = ddc_out_strobe;
+    assign ddc_out_enable = enable;
+
+endmodule //custom_dsp_rx
diff --git a/fpga/usrp2/custom/custom_dsp_tx.v b/fpga/usrp2/custom/custom_dsp_tx.v
new file mode 100644
index 000000000..0848a187f
--- /dev/null
+++ b/fpga/usrp2/custom/custom_dsp_tx.v
@@ -0,0 +1,71 @@
+//
+// Copyright 2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+//COPY ME, CUSTOMIZE ME...
+
+//The following module effects the IO of the DUC chain.
+//By default, this entire module is a simple pass-through.
+
+//To implement DSP logic before the DUC:
+//Implement custom DSP between baseband and duc input.
+
+//To implement DSP logic after the DUC:
+//Implement custom DSP between duc output and frontend.
+
+//To bypass the DUC with custom logic:
+//Implement custom DSP between baseband and frontend.
+
+module custom_dsp_tx
+#(
+    //frontend bus width
+    parameter WIDTH = 24
+)
+(
+    //control signals
+    input clock, //dsp clock
+    input reset, //active high synchronous reset
+    input clear, //active high on packet control init
+    input enable, //active high when streaming enabled
+
+    //user settings bus, controlled through user setting regs API
+    input set_stb, input [7:0] set_addr, input [31:0] set_data,
+
+    //full rate outputs directly to the TX frontend
+    output [WIDTH-1:0] frontend_i,
+    output [WIDTH-1:0] frontend_q,
+
+    //full rate outputs directly from the DUC chain
+    input [WIDTH-1:0] duc_out_i,
+    input [WIDTH-1:0] duc_out_q,
+
+    //strobed samples {I16,Q16} to the TX DUC chain
+    output [31:0] duc_in_sample,
+    input duc_in_strobe, //this is a backpressure signal
+    output duc_in_enable, //enables DUC module
+
+    //strobbed baseband samples {I16,Q16} to this module
+    input [31:0] bb_sample,
+    output bb_strobe //this is a backpressure signal
+);
+
+    assign frontend_i = duc_out_i;
+    assign frontend_q = duc_out_q;
+    assign duc_in_sample = bb_sample;
+    assign bb_strobe = duc_in_strobe;
+    assign duc_in_enable = enable;
+
+endmodule //custom_dsp_tx
diff --git a/fpga/usrp2/custom/custom_engine_rx.v b/fpga/usrp2/custom/custom_engine_rx.v
new file mode 100644
index 000000000..dfeaad2cd
--- /dev/null
+++ b/fpga/usrp2/custom/custom_engine_rx.v
@@ -0,0 +1,53 @@
+//
+// Copyright 2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+//COPY ME, CUSTOMIZE ME...
+
+//The following module is used to re-write receive packets to the host.
+//This module provides a packet-based ram interface for manipulating packets.
+//The user writes a custom engine (state machine) to read the input packet,
+//and to produce a new output packet.
+
+//By default, this entire module is a simple pass-through.
+
+module custom_engine_rx
+#(
+    //buffer size for ram interface engine
+    parameter BUF_SIZE = 10
+)
+(
+    //control signals
+    input clock, input reset, input clear,
+
+    //user settings bus, controlled through user setting regs API
+    input set_stb, input [7:0] set_addr, input [31:0] set_data,
+
+    //ram interface for engine
+    output access_we,
+    output access_stb,
+    input access_ok,
+    output access_done,
+    output access_skip_read,
+    output [BUF_SIZE-1:0] access_adr,
+    input [BUF_SIZE-1:0] access_len,
+    output [35:0] access_dat_o,
+    input [35:0] access_dat_i
+);
+
+    assign access_done = access_ok;
+
+endmodule //custom_engine_rx
diff --git a/fpga/usrp2/custom/custom_engine_tx.v b/fpga/usrp2/custom/custom_engine_tx.v
new file mode 100644
index 000000000..9be728484
--- /dev/null
+++ b/fpga/usrp2/custom/custom_engine_tx.v
@@ -0,0 +1,57 @@
+//
+// Copyright 2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+//COPY ME, CUSTOMIZE ME...
+
+//The following module is used to re-write transmit packets from the host.
+//This module provides a packet-based ram interface for manipulating packets.
+//The user writes a custom engine (state machine) to read the input packet,
+//and to produce a new output packet.
+
+//By default, this entire module is a simple pass-through.
+
+module custom_engine_tx
+#(
+    //buffer size for ram interface engine
+    parameter BUF_SIZE = 10,
+
+    //the number of 32bit lines between start of buffer and vita header
+    //the metadata before the header should be preserved by the engine
+    parameter HEADER_OFFSET = 0
+)
+(
+    //control signals
+    input clock, input reset, input clear,
+
+    //user settings bus, controlled through user setting regs API
+    input set_stb, input [7:0] set_addr, input [31:0] set_data,
+
+    //ram interface for engine
+    output access_we,
+    output access_stb,
+    input access_ok,
+    output access_done,
+    output access_skip_read,
+    output [BUF_SIZE-1:0] access_adr,
+    input [BUF_SIZE-1:0] access_len,
+    output [35:0] access_dat_o,
+    input [35:0] access_dat_i
+);
+
+    assign access_done = access_ok;
+
+endmodule //custom_engine_tx
diff --git a/fpga/usrp2/custom/power_trig.v b/fpga/usrp2/custom/power_trig.v
new file mode 100644
index 000000000..b38059030
--- /dev/null
+++ b/fpga/usrp2/custom/power_trig.v
@@ -0,0 +1,130 @@
+//
+// Copyright 2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+// This a power trigger module implemented on top of the custom dsp template.
+// Power triggering is implemented after the existing DDC chain.
+// Triggering is controlled via user settings registers.
+
+// Register 0:
+//  threshold for power trigger
+//  32 bit unsigned fixed-point number of some arbitrary scaling
+
+module power_trig
+#(
+    //frontend bus width
+    parameter WIDTH = 24,
+    parameter BASE = 0
+)
+(
+    //control signals
+    input clock, //dsp clock
+    input reset, //active high synchronous reset
+    input clear, //active high on packet control init
+    input enable, //active high when streaming enabled
+
+    //user settings bus, controlled through user setting regs API
+    input set_stb, input [7:0] set_addr, input [31:0] set_data,
+
+    //full rate inputs directly from the RX frontend
+    input [WIDTH-1:0] frontend_i,
+    input [WIDTH-1:0] frontend_q,
+
+    //full rate outputs directly to the DDC chain
+    output [WIDTH-1:0] ddc_in_i,
+    output [WIDTH-1:0] ddc_in_q,
+
+    //strobed samples {I16,Q16} from the RX DDC chain
+    input [31:0] ddc_out_sample,
+    input ddc_out_strobe, //high on valid sample
+    output ddc_out_enable, //enables DDC module
+
+    //strobbed baseband samples {I16,Q16} from this module
+    output [31:0] bb_sample,
+    output bb_strobe //high on valid sample
+);
+
+    //leave frontend tied to existing ddc chain
+    assign ddc_in_i = frontend_i;
+    assign ddc_in_q = frontend_q;
+
+    //ddc enable remains tied to global enable
+    assign ddc_out_enable = enable;
+
+    //below we implement a power trigger between baseband samples and ddc output...
+
+   reg [8:0] 	  wr_addr;
+   wire [8:0] 	  rd_addr;
+   reg 		  triggered, triggerable;
+   wire 	  trigger;
+   
+   wire [31:0] 	  delayed_sample;
+   wire [31:0] 	  thresh;
+   
+   setting_reg #(.my_addr(BASE+0)) sr_0
+     (.clk(clk),.rst(reset),.strobe(set_stb),.addr(set_addr),
+      .in(set_data),.out(thresh),.changed());
+
+   assign rd_addr = wr_addr + 1; // FIXME adjustable delay
+
+   ram_2port  #(.DWIDTH(32),.AWIDTH(9)) delay_line
+     (.clka(clk),.ena(1),.wea(ddc_out_strobe),.addra(wr_addr),.dia(ddc_out_sample),.doa(),
+      .clkb(clk),.enb(ddc_out_strobe),.web(1'b0),.addrb(rd_addr),.dib(32'hFFFF),.dob(delayed_sample));
+
+   always @(posedge clock)
+     if(reset | ~enable)
+       wr_addr <= 0;
+     else
+       if(ddc_out_strobe)
+	 wr_addr <= wr_addr + 1;
+
+   always @(posedge clock)
+     if(reset | ~enable)
+       triggerable <= 0;
+     else if(wr_addr == 9'h1FF)  // Wait till we're nearly full
+       triggerable <= 1;
+   
+
+   reg 			      stb_d1, stb_d2;
+   always @(posedge clock) stb_d1 <= ddc_out_strobe;
+   always @(posedge clock) stb_d2 <= stb_d1;
+   
+   assign bb_sample = delayed_sample;
+   assign bb_strobe = stb_d1 & triggered;
+
+   // Compute Mag
+   wire [17:0] 		      mult_in = stb_d1 ? { ddc_out_sample[15],ddc_out_sample[15:0], 1'b0 } : 
+			      { ddc_out_sample[31], ddc_out_sample[31:16], 1'b0 };
+   wire [35:0] 		      prod;
+   reg [31:0] 		      sum;
+   
+   MULT18X18S mult (.P(prod), .A(mult_in), .B(mult_in), .C(clock), .CE(ddc_out_strobe | stb_d1), .R(reset) );
+
+   always @(posedge clock)
+     if(stb_d1)
+       sum <= prod[35:4];
+     else if(stb_d2)
+       sum <= sum + prod[35:4];
+
+   always @(posedge clock)
+     if(reset | ~enable | ~triggerable)
+       triggered <= 0;
+     else if(trigger)
+       triggered <= 1;
+
+   assign trigger = (sum > thresh);
+   
+endmodule // power_trig
diff --git a/fpga/usrp2/custom/power_trig_tb.v b/fpga/usrp2/custom/power_trig_tb.v
new file mode 100644
index 000000000..b8f3385ce
--- /dev/null
+++ b/fpga/usrp2/custom/power_trig_tb.v
@@ -0,0 +1,71 @@
+//
+// Copyright 2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+
+module power_trig_tb();
+   initial $dumpfile("power_trig_tb.vcd");
+   initial $dumpvars(0,power_trig_tb);
+
+   reg clk = 0;
+   always #10 clk <= ~clk;
+   reg rst = 1;
+   initial #100 rst <= 0;
+
+   initial
+     begin
+	set_stb <= 0;
+	#1000;
+	set_stb <= 1;
+     end
+   
+   reg [31:0] sample_in;
+   reg 	      strobe_in;
+   wire [31:0] sample_out;
+   wire        strobe_out;
+   reg 	       set_stb, run;
+   
+   power_trig #(.BASE(0)) power_trig
+     (.clk(clk), .reset(rst), .enable(1),
+      .set_stb(set_stb), .set_addr(0), .set_data(32'h000B_B000),
+      .run(run),
+
+      .ddc_out_sample(sample_in), .ddc_out_strobe(strobe_in),
+      .bb_sample(sample_out), .bb_strobe(strobe_out));
+
+   initial sample_in <= 32'h0100_0300;
+   
+   always @(posedge clk)
+     if(~strobe_in)
+       sample_in <= sample_in + 32'h0001_0001;
+
+   initial
+     #100000 $finish;
+
+   initial 
+     begin
+	run <= 0;
+	#2000 run <= 1;
+	#30000 run <= 0;
+     end
+
+   always @(posedge clk)
+     if(rst | ~run)
+       strobe_in <= 0;
+     else
+       strobe_in <= ~strobe_in;
+   
+endmodule // power_trig_tb
diff --git a/fpga/usrp2/gpif/Makefile.srcs b/fpga/usrp2/gpif/Makefile.srcs
index bf2b7f74d..06cde8afa 100644
--- a/fpga/usrp2/gpif/Makefile.srcs
+++ b/fpga/usrp2/gpif/Makefile.srcs
@@ -11,4 +11,5 @@ gpif_wr.v \
 gpif_rd.v \
 packet_reframer.v \
 packet_splitter.v \
+slave_fifo.v \
 ))
diff --git a/fpga/usrp2/gpif/packet_reframer.v b/fpga/usrp2/gpif/packet_reframer.v
index 923d499ae..8bb8a3678 100644
--- a/fpga/usrp2/gpif/packet_reframer.v
+++ b/fpga/usrp2/gpif/packet_reframer.v
@@ -1,5 +1,5 @@
 //
-// Copyright 2011 Ettus Research LLC
+// Copyright 2011-2012 Ettus Research LLC
 //
 // This program is free software: you can redistribute it and/or modify
 // it under the terms of the GNU General Public License as published by
@@ -16,7 +16,7 @@
 //
 
 
-// Join vita packets longer than one GPIF frame, drop padding on short frames
+// Join vita packets longer than one GPIF frame
 
 module packet_reframer
   (input clk, input reset, input clear,
@@ -25,18 +25,20 @@ module packet_reframer
    output dst_rdy_o,
    output [18:0] data_o,
    output src_rdy_o,
-   input dst_rdy_i);
+   input dst_rdy_i,
+   output reg state,
+   output eof_out,
+   output reg [15:0] length);
 
-   reg [1:0] state;
-   reg [15:0] length;
+   //reg state;
+   //reg [15:0] length;
    
    localparam RF_IDLE = 0;
    localparam RF_PKT = 1;
-   localparam RF_DUMP = 2;
    
    always @(posedge clk)
      if(reset | clear)
-       state <= 0;
+       state <= RF_IDLE;
      else
        if(src_rdy_i & dst_rdy_i)
 	 case(state)
@@ -47,26 +49,16 @@ module packet_reframer
 	     end
 	   RF_PKT :
 	     begin
-		if(length == 2)
-		  if(data_i[17])
-		    state <= RF_IDLE;
-		  else
-		    state <= RF_DUMP;
-		else
-		  length <= length - 1;
+		if(eof_out) state <= RF_IDLE;
+		length <= length - 1;
 	     end
-	   RF_DUMP :
-	     if(data_i[17])
-	       state <= RF_IDLE;
-	   default :
-	     state<= RF_IDLE;
 	 endcase // case (state)
    
    assign dst_rdy_o = dst_rdy_i; // this is a little pessimistic but ok
-   assign src_rdy_o = src_rdy_i & (state != RF_DUMP);
+   assign src_rdy_o = src_rdy_i;
    
    wire occ_out = 0;
-   wire eof_out = (state == RF_PKT) & (length == 2);
+   assign eof_out = (state == RF_PKT) & (length == 2);
    wire sof_out = (state == RF_IDLE);
    wire [15:0] data_out = data_i[15:0];
    assign data_o = {occ_out, eof_out, sof_out, data_out};
diff --git a/fpga/usrp2/gpif/slave_fifo.v b/fpga/usrp2/gpif/slave_fifo.v
new file mode 100644
index 000000000..10740942b
--- /dev/null
+++ b/fpga/usrp2/gpif/slave_fifo.v
@@ -0,0 +1,467 @@
+//
+// Copyright 2011-2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+//////////////////////////////////////////////////////////////////////////////////
+
+//this is a FIFO master interface for the FX2 in "slave fifo" mode.
+
+module slave_fifo
+  #(parameter TXFIFOSIZE = 12, parameter RXFIFOSIZE = 12)
+   (// GPIF signals
+    input gpif_clk, input gpif_rst,
+    inout [15:0] gpif_d,
+    input [3:0] gpif_ctl,
+    output sloe, output slrd, output slwr, output pktend, output [1:0] fifoadr,
+    
+    // Wishbone signals
+    input wb_clk, input wb_rst,
+    output [15:0] wb_adr_o, output [15:0] wb_dat_mosi, input [15:0] wb_dat_miso,
+    output [1:0] wb_sel_o, output wb_cyc_o, output wb_stb_o, output wb_we_o, input wb_ack_i,
+    input [7:0] triggers,
+    
+    input dsp_rx_run,
+    
+    // FIFO interface
+    input fifo_clk, input fifo_rst, input clear_tx, input clear_rx,
+    output [35:0] tx_data_o, output tx_src_rdy_o, input tx_dst_rdy_i,
+    input [35:0] rx_data_i, input rx_src_rdy_i, output rx_dst_rdy_o,
+    input [35:0] tx_err_data_i, input tx_err_src_rdy_i, output tx_err_dst_rdy_o,
+    output tx_underrun, output rx_overrun,
+    
+    input [15:0] test_len, input [7:0] test_rate, input [3:0] test_ctrl,
+    output [31:0] debug0, output [31:0] debug1
+    );
+
+   // inputs to FPGA (all active low)
+   wire       FX2_DE = ~gpif_ctl[0]; //EP2 FX2 FIFO empty (FLAGA)
+   wire       FX2_CE = ~gpif_ctl[1]; //EP4 FX2 FIFO empty (FLAGB)
+   wire       FX2_DF = ~gpif_ctl[2]; //EP6 FX2 FIFO full  (FLAGC)
+   wire       FX2_CF = ~gpif_ctl[3]; //EP8 FX2 FIFO full  (FLAGD)
+
+   wire [17:0] 	  gpif_d_out_ctrl, gpif_d_out_data, gpif_d_out;
+
+   // ////////////////////////////////////////////////////////////////////
+   // GPIF bus master state machine
+
+   //transfer size for GPIF data. this can be anything really, it's specified only for
+   //fairness in bus sharing. 256 lines is 512 bytes over the wire, half the size of
+   //the double buffers in B100/B150. this should probably be a toplevel parameter or even
+   //a settings register value.
+   localparam data_transfer_size = 256;
+   localparam ctrl_transfer_size = 16; //probably unnecessary since ctrl xfers won't back up
+
+   // state machine i/o to four fifos
+   //tx
+   wire ctrl_tx_dst_rdy; //sm input, ctrl tx path has space
+   wire ctrl_tx_src_rdy; //sm output, ctrl tx path enable
+   reg data_tx_dst_rdy; //sm input, data tx path has space
+   wire data_tx_src_rdy; //sm output, data tx path enable
+
+   //rx
+   wire ctrl_rx_dst_rdy; //sm output, ctrl rx path enable
+   wire ctrl_rx_src_rdy; //sm input, ctrl rx path has space
+   wire data_rx_dst_rdy; //sm output, data rx path enable
+   wire data_rx_src_rdy; //sm input, data rx path has space
+
+   reg [9:0] transfer_count; //number of lines (a line is 16 bits) in active transfer
+
+   wire       sop, eop; //SOP/EOP markers for TX data packets
+   
+   reg pktend_latch;
+
+   reg [3:0] state; //state machine current state
+   localparam STATE_IDLE    = 0;
+   localparam STATE_DATA_RX = 5;
+   localparam STATE_DATA_TX = 3;
+   localparam STATE_CTRL_RX = 6;
+   localparam STATE_CTRL_TX = 9;
+   localparam STATE_DATA_TX_SLOE = 2;
+   localparam STATE_CTRL_TX_SLOE = 8;
+   localparam STATE_DATA_RX_ADR = 1;
+   localparam STATE_CTRL_RX_ADR = 4;
+   localparam STATE_PKTEND = 7;
+
+   //logs the last bus user for xfer fairness
+   //we only care about data rx vs. tx since ctrl pkts are so short
+   reg last_data_bus_hog;
+   localparam BUS_HOG_RX = 0;
+   localparam BUS_HOG_TX = 1;
+
+   // //////////////////////////////////////////////////////////////
+   // FX2 slave FIFO bus master state machine
+   //
+   always @(posedge gpif_clk)
+     if(gpif_rst) 
+       state <= STATE_IDLE;
+     else
+        begin
+       case (state)
+         STATE_IDLE:
+            begin
+           transfer_count <= 0;
+           //handle transitions to other states
+           if(ctrl_tx_dst_rdy & ~FX2_CE) //if there's room in the ctrl fifo and the FX2 has ctrl data
+             state <= STATE_CTRL_TX_SLOE;
+           else if(ctrl_rx_src_rdy & ~FX2_CF) //if the ctrl fifo has data and the FX2 isn't full
+             state <= STATE_CTRL_RX_ADR;
+           else if(data_tx_dst_rdy & ~FX2_DE & last_data_bus_hog == BUS_HOG_RX) //if there's room in the data fifo and the FX2 has data
+             state <= STATE_DATA_TX_SLOE;
+           else if(data_rx_src_rdy & ~FX2_DF & last_data_bus_hog == BUS_HOG_TX) //if the data fifo has data and the FX2 isn't full
+             state <= STATE_DATA_RX_ADR;
+           else if(data_tx_dst_rdy & ~FX2_DE)
+             state <= STATE_DATA_TX_SLOE;
+           else if(data_rx_src_rdy & ~FX2_DF)
+             state <= STATE_DATA_RX_ADR;
+           else if(~data_rx_src_rdy & ~dsp_rx_run & pktend_latch & ~FX2_DF)
+             state <= STATE_PKTEND;
+             
+           if(data_rx_src_rdy)
+             pktend_latch <= 1;
+            end
+
+         STATE_DATA_TX_SLOE: //just to assert SLOE one cycle before SLRD
+           state <= STATE_DATA_TX;
+         STATE_CTRL_TX_SLOE:
+           state <= STATE_CTRL_TX;
+
+         STATE_DATA_RX_ADR: //just to assert FIFOADR one cycle before SLWR
+           state <= STATE_DATA_RX;
+         STATE_CTRL_RX_ADR:
+           state <= STATE_CTRL_RX;
+
+         STATE_DATA_RX:
+            begin
+           if((transfer_count == data_transfer_size) | FX2_DF | (~data_rx_src_rdy))
+             state <= STATE_IDLE;
+
+           transfer_count <= transfer_count + 1;
+           last_data_bus_hog <= BUS_HOG_RX;
+            end
+            
+         STATE_PKTEND:
+            begin
+           state <= STATE_IDLE;
+           pktend_latch <= 0;
+            end
+            
+         STATE_DATA_TX:
+            begin
+           if((transfer_count == data_transfer_size) | FX2_DE )/*| (~data_tx_dst_rdy))*/
+             state <= STATE_IDLE;
+           transfer_count <= transfer_count + 1;
+           last_data_bus_hog <= BUS_HOG_TX;
+            end
+         STATE_CTRL_RX:
+            begin
+           if(FX2_CF | (~ctrl_rx_src_rdy))
+             state <= STATE_IDLE;
+           transfer_count <= transfer_count + 1;
+            end
+         STATE_CTRL_TX:
+            begin
+           if(FX2_CE | (~ctrl_tx_dst_rdy))
+             state <= STATE_IDLE;
+           transfer_count <= transfer_count + 1;
+            end
+       endcase
+        end
+
+   // ///////////////////////////////////////////////////////////////////
+   // fifo signal assignments and enables
+
+   //enable fifos
+   assign data_rx_dst_rdy = (state == STATE_DATA_RX);
+   assign data_tx_src_rdy = (state == STATE_DATA_TX);
+   assign ctrl_rx_dst_rdy = (state == STATE_CTRL_RX);
+   assign ctrl_tx_src_rdy = (state == STATE_CTRL_TX);
+
+   //tx framing (this is super suspect)
+   //eop should be used only to set the EOP bit going into FIFOs
+   wire eop_data, eop_ctrl;
+   assign sop = (transfer_count == 0);
+   assign eop_data = (transfer_count == (data_transfer_size-1));
+   assign eop_ctrl = (transfer_count == (ctrl_transfer_size-1));
+   assign eop = (state == STATE_DATA_TX) ? eop_data : eop_ctrl;
+
+   // ////////////////////////////////////////////////////////////////////
+   // set GPIF pins
+
+   //set fifoadr to the appropriate endpoint
+   // {0,0}: EP2, data TX from host
+   // {0,1}: EP4, ctrl TX from host
+   // {1,0}: EP6, data RX to host
+   // {1,1}: EP8, ctrl RX to host
+   assign fifoadr = {(state == STATE_DATA_RX) | (state == STATE_CTRL_RX) | (state == STATE_DATA_RX_ADR) | (state == STATE_CTRL_RX_ADR) | (state == STATE_PKTEND),
+                     (state == STATE_CTRL_RX) | (state == STATE_CTRL_RX_ADR) | (state == STATE_CTRL_TX) | (state == STATE_CTRL_TX_SLOE)};
+   //set sloe, slwr, slrd (all active low)
+   //SLOE gets asserted when we want data from the FX2; i.e., TX mode
+   assign sloe = ~{(state == STATE_DATA_TX) | (state == STATE_CTRL_TX) | (state == STATE_DATA_TX_SLOE) | (state == STATE_CTRL_TX_SLOE)};
+   //"read" and "write" here are from the master's point of view;
+   //so "read" means "transmit" and "write" means "receive"
+   assign slwr = ~{(state == STATE_DATA_RX) | (state == STATE_CTRL_RX)};
+   assign slrd = ~{(state == STATE_DATA_TX) | (state == STATE_CTRL_TX)};
+
+   wire pktend_ctrl, pktend_data;
+   assign pktend_ctrl = ((~ctrl_rx_src_rdy | gpif_d_out_ctrl[17]) & (state == STATE_CTRL_RX));
+   assign pktend_data = (state == STATE_PKTEND);
+   assign pktend = ~(pktend_ctrl | pktend_data);
+
+   //mux between ctrl/data RX data out based on endpoint selection
+   assign gpif_d_out = fifoadr[0] ? gpif_d_out_ctrl : gpif_d_out_data;
+   // GPIF output data lines, tristate
+   assign gpif_d = sloe ? gpif_d_out : 16'bz;
+   
+   // ////////////////////////////////////////////////////////////////////
+   // TX Data Path
+
+   wire [18:0] 	  tx19_data;
+   wire 	  tx19_src_rdy, tx19_dst_rdy;
+   wire [35:0] 	  tx36_data;
+   wire 	  tx36_src_rdy, tx36_dst_rdy;
+   wire [17:0]    data_tx_int;
+   wire           tx_src_rdy_int, tx_dst_rdy_int;
+   
+   wire [15:0] wr_fifo_space;
+   
+   always @(posedge gpif_clk)
+     if(gpif_rst)
+       data_tx_dst_rdy <= 0;
+     else
+       data_tx_dst_rdy <= wr_fifo_space >= 256;
+
+   fifo_cascade #(.WIDTH(18), .SIZE(12)) wr_fifo
+     (.clk(gpif_clk), .reset(gpif_rst), .clear(clear_tx),
+      .datain({eop,sop,gpif_d}), .src_rdy_i(data_tx_src_rdy), .dst_rdy_o(/*data_tx_dst_rdy*/), .space(wr_fifo_space),
+      .dataout(data_tx_int), .src_rdy_o(tx_src_rdy_int), .dst_rdy_i(tx_dst_rdy_int), .occupied());
+   
+   fifo_2clock_cascade #(.WIDTH(18), .SIZE(4)) wr_fifo_2clk
+     (.wclk(gpif_clk), .datain(data_tx_int), .src_rdy_i(tx_src_rdy_int), .dst_rdy_o(tx_dst_rdy_int), .space(),
+      .rclk(fifo_clk), .dataout(tx19_data[17:0]), .src_rdy_o(tx19_src_rdy), .dst_rdy_i(tx19_dst_rdy), .occupied(),
+      .arst(fifo_rst));
+      
+   assign tx19_data[18] = 1'b0;
+
+   // join vita packets which are longer than one frame, drop frame padding
+   wire [18:0] 	  refr_data;
+   wire 	  refr_src_rdy, refr_dst_rdy;
+   wire refr_state;
+   wire refr_eof;
+   wire [15:0] refr_len;
+   
+   packet_reframer tx_packet_reframer 
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx),
+      .data_i(tx19_data), .src_rdy_i(tx19_src_rdy), .dst_rdy_o(tx19_dst_rdy),
+      .data_o(refr_data), .src_rdy_o(refr_src_rdy), .dst_rdy_i(refr_dst_rdy),
+      .state(refr_state), .eof_out(refr_eof), .length(refr_len));
+
+   fifo19_to_fifo36 #(.LE(1)) f19_to_f36
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx),
+      .f19_datain(refr_data), .f19_src_rdy_i(refr_src_rdy), .f19_dst_rdy_o(refr_dst_rdy),
+      .f36_dataout(tx36_data), .f36_src_rdy_o(tx36_src_rdy), .f36_dst_rdy_i(tx36_dst_rdy));
+   
+   fifo_cascade #(.WIDTH(36), .SIZE(TXFIFOSIZE)) tx_fifo36
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx),
+      .datain(tx36_data), .src_rdy_i(tx36_src_rdy), .dst_rdy_o(tx36_dst_rdy),
+      .dataout(tx_data_o), .src_rdy_o(tx_src_rdy_o), .dst_rdy_i(tx_dst_rdy_i));
+
+   // ////////////////////////////////////////////
+   // RX Data Path
+
+   wire [35:0] 	  rx36_data;
+   wire 	  rx36_src_rdy, rx36_dst_rdy;
+   wire [18:0] 	  rx19_data;
+   wire 	  rx19_src_rdy, rx19_dst_rdy;
+   wire [15:0] rxfifospace;
+
+   //deep 36 bit wide input fifo buffers from DSP
+   fifo_cascade #(.WIDTH(36), .SIZE(8)) rx_fifo36
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx),
+      .datain(rx_data_i), .src_rdy_i(rx_src_rdy_i), .dst_rdy_o(rx_dst_rdy_o),
+      .dataout(rx36_data), .src_rdy_o(rx36_src_rdy), .dst_rdy_i(rx36_dst_rdy));
+
+   //convert to fifo19
+   fifo36_to_fifo19 #(.LE(1)) f36_to_f19
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx),
+      .f36_datain(rx36_data), .f36_src_rdy_i(rx36_src_rdy), .f36_dst_rdy_o(rx36_dst_rdy),
+      .f19_dataout(rx19_data), .f19_src_rdy_o(rx19_src_rdy), .f19_dst_rdy_i(rx19_dst_rdy) );
+
+   wire [18:0] 	data_rx_int;
+   wire 	rx_src_rdy_int, rx_dst_rdy_int;
+   //clock domain crossing fifo for RX data
+   fifo_2clock_cascade #(.WIDTH(19), .SIZE(4)) rd_fifo_2clk
+     (.wclk(fifo_clk), .datain(rx19_data), .src_rdy_i(rx19_src_rdy), .dst_rdy_o(rx19_dst_rdy), .space(),
+      .rclk(~gpif_clk), .dataout(data_rx_int), .src_rdy_o(rx_src_rdy_int), .dst_rdy_i(rx_dst_rdy_int), .occupied(),
+      .arst(fifo_rst));
+
+   //rd_fifo buffers writes to the 2clock fifo above
+   fifo_cascade #(.WIDTH(19), .SIZE(RXFIFOSIZE)) rd_fifo
+     (.clk(~gpif_clk), .reset(gpif_rst), .clear(clear_rx),
+      .datain(data_rx_int), .src_rdy_i(rx_src_rdy_int), .dst_rdy_o(rx_dst_rdy_int), .space(rxfifospace),
+      .dataout(gpif_d_out_data), .src_rdy_o(data_rx_src_rdy), .dst_rdy_i(data_rx_dst_rdy), .occupied());
+
+   // ////////////////////////////////////////////////////////////////////
+   // FIFO to Wishbone interface
+
+   wire [18:0] 	  resp_data, resp_int;
+   wire 	  resp_src_rdy, resp_dst_rdy;
+   wire 	  resp_src_rdy_int, resp_dst_rdy_int;
+   
+   wire [18:0] 	  tx_err19_data;
+   wire 	  tx_err19_src_rdy, tx_err19_dst_rdy;
+
+   wire [18:0] 	  ctrl_data;
+   wire 	  ctrl_src_rdy, ctrl_dst_rdy;
+
+   fifo_to_wb fifo_to_wb
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(0),
+      .data_i(ctrl_data), .src_rdy_i(ctrl_src_rdy), .dst_rdy_o(ctrl_dst_rdy),
+      .data_o(resp_int), .src_rdy_o(resp_src_rdy_int), .dst_rdy_i(resp_dst_rdy_int),
+      .wb_adr_o(wb_adr_o), .wb_dat_mosi(wb_dat_mosi), .wb_dat_miso(wb_dat_miso), .wb_sel_o(wb_sel_o), 
+      .wb_cyc_o(wb_cyc_o), .wb_stb_o(wb_stb_o), .wb_we_o(wb_we_o), .wb_ack_i(wb_ack_i),
+      .triggers(triggers),
+      .debug0(), .debug1());
+      
+   // ////////////////////////////////////////////////////////////////////
+   // TX CTRL PATH (ctrl commands into Wishbone)
+
+   //how does this use fifo_clk instead of wb_clk
+   //answer: on b100 fifo clk IS wb clk
+   fifo_2clock_cascade #(.WIDTH(19), .SIZE(4)) ctrl_fifo_2clk
+     (.wclk(gpif_clk), .datain({1'b0,eop,sop,gpif_d}), 
+      .src_rdy_i(ctrl_tx_src_rdy), .dst_rdy_o(ctrl_tx_dst_rdy), .space(),
+      .rclk(fifo_clk), .dataout(ctrl_data), 
+      .src_rdy_o(ctrl_src_rdy), .dst_rdy_i(ctrl_dst_rdy), .occupied(),
+      .arst(fifo_rst));
+
+   // ////////////////////////////////////////////////////////////////////
+   // RX CTRL PATH (async packets, ctrl response data)
+   
+   //tx_err_data_i is the 36wide tx async err data clocked on fifo_clk
+   fifo36_to_fifo19 #(.LE(1)) f36_to_f19_txerr
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx),
+      .f36_datain(tx_err_data_i), .f36_src_rdy_i(tx_err_src_rdy_i), .f36_dst_rdy_o(tx_err_dst_rdy_o),
+      .f19_dataout(tx_err19_data), .f19_src_rdy_o(tx_err19_src_rdy), .f19_dst_rdy_i(tx_err19_dst_rdy) );
+
+   //mux FIFO-to-WB along with async tx err pkts into one ctrl resp fifo
+   //how is this clocked on wb_clk?
+   fifo19_mux #(.prio(0)) mux_err_stream
+     (.clk(wb_clk), .reset(wb_rst), .clear(clear_rx),
+      .data0_i(resp_int), .src0_rdy_i(resp_src_rdy_int), .dst0_rdy_o(resp_dst_rdy_int),
+      .data1_i(tx_err19_data), .src1_rdy_i(tx_err19_src_rdy), .dst1_rdy_o(tx_err19_dst_rdy),
+      .data_o(resp_data), .src_rdy_o(resp_src_rdy), .dst_rdy_i(resp_dst_rdy));
+
+   //clock domain crossing cascade fifo for mux_err_stream to get from wb_clk to gpif_clk
+   //the output of this fifo is CTRL DATA PENDING FOR GPIF
+   fifo_2clock_cascade #(.WIDTH(18), .SIZE(4)) resp_fifo_2clk
+     (.wclk(wb_clk), .datain(resp_data[17:0]), .src_rdy_i(resp_src_rdy), .dst_rdy_o(resp_dst_rdy), .space(),
+      .rclk(~gpif_clk), .dataout(gpif_d_out_ctrl), 
+      .src_rdy_o(ctrl_rx_src_rdy), .dst_rdy_i(ctrl_rx_dst_rdy), .occupied(),
+      .arst(wb_rst));
+
+        
+   // ////////////////////////////////////////////////////////////////////
+   // Debug support, timed and loopback
+   // RX side muxes test data into the same stream
+
+   ///////////////////////////////////////////////////////////////////////
+   // debug lines
+   wire [31:0] 	  debug_rd, debug_wr, debug_split0, debug_split1;
+   
+   wire [35:0] 	timedrx_data, loopbackrx_data, testrx_data;
+   wire [35:0] 	timedtx_data, loopbacktx_data, testtx_data;
+   wire 	timedrx_src_rdy, timedrx_dst_rdy, loopbackrx_src_rdy, loopbackrx_dst_rdy,
+		testrx_src_rdy, testrx_dst_rdy;
+   wire 	timedtx_src_rdy, timedtx_dst_rdy, loopbacktx_src_rdy, loopbacktx_dst_rdy,
+		testtx_src_rdy, testtx_dst_rdy;
+   wire 	timedrx_src_rdy_int, timedrx_dst_rdy_int, timedtx_src_rdy_int, timedtx_dst_rdy_int;
+
+   wire [31:0] 	total, crc_err, seq_err, len_err;
+   wire 	sel_testtx = test_ctrl[0];
+   wire 	sel_loopbacktx = test_ctrl[1];
+   wire 	pkt_src_enable = test_ctrl[2];
+   wire 	pkt_sink_enable = test_ctrl[3];
+/*   
+   fifo36_mux rx_test_mux_lvl_1
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx),
+      .data0_i(timedrx_data), .src0_rdy_i(timedrx_src_rdy), .dst0_rdy_o(timedrx_dst_rdy),
+      .data1_i(loopbackrx_data), .src1_rdy_i(loopbackrx_src_rdy), .dst1_rdy_o(loopbackrx_dst_rdy),
+      .data_o(testrx_data), .src_rdy_o(testrx_src_rdy), .dst_rdy_i(testrx_dst_rdy));
+   
+   fifo36_mux rx_test_mux_lvl_2
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx),
+      .data0_i(testrx_data), .src0_rdy_i(testrx_src_rdy), .dst0_rdy_o(testrx_dst_rdy),
+      .data1_i(rx_data_i), .src1_rdy_i(rx_src_rdy_i), .dst1_rdy_o(rx_dst_rdy_o),
+      .data_o(rx_data), .src_rdy_o(rx_src_rdy), .dst_rdy_i(rx_dst_rdy));
+   
+   fifo_short #(.WIDTH(36)) loopback_fifo
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx | clear_rx),
+      .datain(loopbacktx_data), .src_rdy_i(loopbacktx_src_rdy), .dst_rdy_o(loopbacktx_dst_rdy),
+      .dataout(loopbackrx_data), .src_rdy_o(loopbackrx_src_rdy), .dst_rdy_i(loopbackrx_dst_rdy));
+   
+   // Crossbar used as a demux for switching TX stream to main DSP or to test logic
+   crossbar36 tx_crossbar_lvl_1
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx),
+      .cross(sel_testtx),
+      .data0_i(tx_data), .src0_rdy_i(tx_src_rdy), .dst0_rdy_o(tx_dst_rdy),
+      .data1_i(tx_data), .src1_rdy_i(1'b0), .dst1_rdy_o(),  // No 2nd input
+      .data0_o(tx_data_o), .src0_rdy_o(tx_src_rdy_o), .dst0_rdy_i(tx_dst_rdy_i),
+      .data1_o(testtx_data), .src1_rdy_o(testtx_src_rdy), .dst1_rdy_i(testtx_dst_rdy) );
+   
+   crossbar36 tx_crossbar_lvl_2
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx),
+      .cross(sel_loopbacktx),
+      .data0_i(testtx_data), .src0_rdy_i(testtx_src_rdy), .dst0_rdy_o(testtx_dst_rdy),
+      .data1_i(testtx_data), .src1_rdy_i(1'b0), .dst1_rdy_o(),  // No 2nd input
+      .data0_o(timedtx_data), .src0_rdy_o(timedtx_src_rdy), .dst0_rdy_i(timedtx_dst_rdy),
+      .data1_o(loopbacktx_data), .src1_rdy_o(loopbacktx_src_rdy), .dst1_rdy_i(loopbacktx_dst_rdy) );
+   
+   // Fixed rate TX traffic consumer
+   fifo_pacer tx_pacer
+     (.clk(fifo_clk), .reset(fifo_rst), .rate(test_rate), .enable(pkt_sink_enable),
+      .src1_rdy_i(timedtx_src_rdy), .dst1_rdy_o(timedtx_dst_rdy),
+      .src2_rdy_o(timedtx_src_rdy_int), .dst2_rdy_i(timedtx_dst_rdy_int),
+      .underrun(tx_underrun), .overrun());
+
+   packet_verifier32 pktver32
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx),
+      .data_i(timedtx_data), .src_rdy_i(timedtx_src_rdy_int), .dst_rdy_o(timedtx_dst_rdy_int),
+      .total(total), .crc_err(crc_err), .seq_err(seq_err), .len_err(len_err));
+
+   // Fixed rate RX traffic generator
+   vita_pkt_gen pktgen
+     (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx),
+      .len(test_len),
+      .data_o(timedrx_data), .src_rdy_o(timedrx_src_rdy_int), .dst_rdy_i(timedrx_dst_rdy_int));
+
+   fifo_pacer rx_pacer
+     (.clk(fifo_clk), .reset(fifo_rst), .rate(test_rate), .enable(pkt_src_enable),
+      .src1_rdy_i(timedrx_src_rdy_int), .dst1_rdy_o(timedrx_dst_rdy_int),
+      .src2_rdy_o(timedrx_src_rdy), .dst2_rdy_i(timedrx_dst_rdy),
+      .underrun(), .overrun(rx_overrun));
+*/
+   // ////////////////////////////////////////////
+   //    DEBUG
+   
+   assign debug0 = { pktend_latch, data_rx_src_rdy, gpif_ctl[3:0], sloe, slrd, slwr, pktend, fifoadr[1:0], state[3:0], gpif_d[15:0]};
+   //assign debug0 = { data_tx_src_rdy, data_tx_dst_rdy, tx_src_rdy_int, tx_dst_rdy_int, 
+   //                  tx19_src_rdy, tx19_dst_rdy, refr_src_rdy, refr_dst_rdy, 
+   //                  tx36_src_rdy, tx36_dst_rdy,
+   //                  gpif_ctl[3:0], fifoadr[1:0], 
+   //                  wr_fifo_space[15:0]};
+   assign debug1 = { 16'b0, transfer_count[7:0], ctrl_rx_src_rdy, ctrl_tx_dst_rdy, data_rx_src_rdy,
+                     data_tx_dst_rdy, ctrl_tx_src_rdy, ctrl_rx_dst_rdy, data_tx_src_rdy, data_rx_dst_rdy};
+endmodule // slave_fifo
diff --git a/fpga/usrp2/sdr_lib/Makefile.srcs b/fpga/usrp2/sdr_lib/Makefile.srcs
index 629b92cc8..e6c4c5343 100644
--- a/fpga/usrp2/sdr_lib/Makefile.srcs
+++ b/fpga/usrp2/sdr_lib/Makefile.srcs
@@ -1,5 +1,5 @@
 #
-# Copyright 2010 Ettus Research LLC
+# Copyright 2010-2012 Ettus Research LLC
 #
 
 ##################################################
@@ -23,9 +23,10 @@ clip_reg.v \
 cordic.v \
 cordic_z24.v \
 cordic_stage.v \
-dsp_core_rx.v \
-dsp_core_tx.v \
+ddc_chain.v \
+duc_chain.v \
 dspengine_16to8.v \
+dspengine_8to16.v \
 hb_dec.v \
 hb_interp.v \
 pipectrl.v \
@@ -39,4 +40,6 @@ sign_extend.v \
 small_hb_dec.v \
 small_hb_int.v \
 tx_frontend.v \
+dsp_tx_glue.v \
+dsp_rx_glue.v \
 ))
diff --git a/fpga/usrp2/sdr_lib/cordic_z24.v b/fpga/usrp2/sdr_lib/cordic_z24.v
index 97b7beaf7..51b074a33 100644
--- a/fpga/usrp2/sdr_lib/cordic_z24.v
+++ b/fpga/usrp2/sdr_lib/cordic_z24.v
@@ -119,8 +119,6 @@ module cordic_z24(clock, reset, enable, xi, yi, zi, xo, yo, zo );
    assign xo = x20[bitwidth:1];  
    assign yo = y20[bitwidth:1];
    assign zo = z20;		  
-   //assign xo = x20[bitwidth+1:2];  // CORDIC gain is ~1.6, plus gain from rotating vectors
-   //assign yo = y20[bitwidth+1:2];
 
 endmodule // cordic
 
diff --git a/fpga/usrp2/sdr_lib/ddc_chain.v b/fpga/usrp2/sdr_lib/ddc_chain.v
new file mode 100644
index 000000000..c32c9f491
--- /dev/null
+++ b/fpga/usrp2/sdr_lib/ddc_chain.v
@@ -0,0 +1,190 @@
+//
+// Copyright 2011-2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+//! The USRP digital down-conversion chain
+
+module ddc_chain
+  #(
+    parameter BASE = 0,
+    parameter DSPNO = 0,
+    parameter WIDTH = 24
+  )
+  (input clk, input rst, input clr,
+   input set_stb, input [7:0] set_addr, input [31:0] set_data,
+   input set_stb_user, input [7:0] set_addr_user, input [31:0] set_data_user,
+
+   // From RX frontend
+   input [WIDTH-1:0] rx_fe_i,
+   input [WIDTH-1:0] rx_fe_q,
+
+   // To RX control
+   output [31:0] sample,
+   input run,
+   output strobe,
+   output [31:0] debug
+   );
+
+   localparam  cwidth = 25;
+   localparam  zwidth = 24;
+
+   wire ddc_enb;
+   wire [31:0] phase_inc;
+   reg [31:0]  phase;
+
+   wire [17:0] scale_factor;
+   wire [cwidth-1:0] i_cordic, q_cordic;
+   wire [WIDTH-1:0] i_cordic_clip, q_cordic_clip;
+   wire [WIDTH-1:0] i_cic, q_cic;
+   wire [WIDTH-1:0] i_hb1, q_hb1;
+   wire [WIDTH-1:0] i_hb2, q_hb2;
+   
+   wire        strobe_cic, strobe_hb1, strobe_hb2;
+   wire        enable_hb1, enable_hb2;
+   wire [7:0]  cic_decim_rate;
+
+   reg [WIDTH-1:0]  rx_fe_i_mux, rx_fe_q_mux;
+   wire        realmode;
+   wire        swap_iq;
+   
+   setting_reg #(.my_addr(BASE+0)) sr_0
+     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
+      .in(set_data),.out(phase_inc),.changed());
+
+   setting_reg #(.my_addr(BASE+1), .width(18)) sr_1
+     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
+      .in(set_data),.out(scale_factor),.changed());
+
+   setting_reg #(.my_addr(BASE+2), .width(10)) sr_2
+     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
+      .in(set_data),.out({enable_hb1, enable_hb2, cic_decim_rate}),.changed());
+
+   setting_reg #(.my_addr(BASE+3), .width(2)) sr_3
+     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
+      .in(set_data),.out({realmode,swap_iq}),.changed());
+
+   // MUX so we can do realmode signals on either input
+   
+   always @(posedge clk)
+     if(swap_iq)
+       begin
+	  rx_fe_i_mux <= rx_fe_q;
+	  rx_fe_q_mux <= realmode ? 0 : rx_fe_i;
+       end
+     else
+       begin
+	  rx_fe_i_mux <= rx_fe_i;
+	  rx_fe_q_mux <= realmode ? 0 : rx_fe_q;
+       end
+
+   // NCO
+   always @(posedge clk)
+     if(rst)
+       phase <= 0;
+     else if(~ddc_enb)
+       phase <= 0;
+     else
+       phase <= phase + phase_inc;
+
+   //sign extension of cordic input
+   wire [WIDTH-1:0] to_ddc_chain_i, to_ddc_chain_q;
+   wire [cwidth-1:0] to_cordic_i, to_cordic_q;
+   sign_extend #(.bits_in(WIDTH), .bits_out(cwidth)) sign_extend_cordic_i (.in(to_ddc_chain_i), .out(to_cordic_i));
+   sign_extend #(.bits_in(WIDTH), .bits_out(cwidth)) sign_extend_cordic_q (.in(to_ddc_chain_q), .out(to_cordic_q));
+
+   // CORDIC  24-bit I/O
+   cordic_z24 #(.bitwidth(cwidth))
+     cordic(.clock(clk), .reset(rst), .enable(ddc_enb),
+	    .xi(to_cordic_i),. yi(to_cordic_q), .zi(phase[31:32-zwidth]),
+	    .xo(i_cordic),.yo(q_cordic),.zo() );
+
+   clip_reg #(.bits_in(cwidth), .bits_out(WIDTH)) clip_i
+     (.clk(clk), .in(i_cordic), .strobe_in(1'b1), .out(i_cordic_clip));
+   clip_reg #(.bits_in(cwidth), .bits_out(WIDTH)) clip_q
+     (.clk(clk), .in(q_cordic), .strobe_in(1'b1), .out(q_cordic_clip));
+
+   // CIC decimator  24 bit I/O
+   cic_strober cic_strober(.clock(clk),.reset(rst),.enable(ddc_enb),.rate(cic_decim_rate),
+			   .strobe_fast(1),.strobe_slow(strobe_cic) );
+
+   cic_decim #(.bw(WIDTH))
+     decim_i (.clock(clk),.reset(rst),.enable(ddc_enb),
+	      .rate(cic_decim_rate),.strobe_in(1'b1),.strobe_out(strobe_cic),
+	      .signal_in(i_cordic_clip),.signal_out(i_cic));
+   
+   cic_decim #(.bw(WIDTH))
+     decim_q (.clock(clk),.reset(rst),.enable(ddc_enb),
+	      .rate(cic_decim_rate),.strobe_in(1'b1),.strobe_out(strobe_cic),
+	      .signal_in(q_cordic_clip),.signal_out(q_cic));
+
+   // First (small) halfband  24 bit I/O
+   small_hb_dec #(.WIDTH(WIDTH)) small_hb_i
+     (.clk(clk),.rst(rst),.bypass(~enable_hb1),.run(ddc_enb),
+      .stb_in(strobe_cic),.data_in(i_cic),.stb_out(strobe_hb1),.data_out(i_hb1));
+   
+   small_hb_dec #(.WIDTH(WIDTH)) small_hb_q
+     (.clk(clk),.rst(rst),.bypass(~enable_hb1),.run(ddc_enb),
+      .stb_in(strobe_cic),.data_in(q_cic),.stb_out(),.data_out(q_hb1));
+
+   // Second (large) halfband  24 bit I/O
+   wire [8:0]  cpi_hb = enable_hb1 ? {cic_decim_rate,1'b0} : {1'b0,cic_decim_rate};
+   hb_dec #(.WIDTH(WIDTH)) hb_i
+     (.clk(clk),.rst(rst),.bypass(~enable_hb2),.run(ddc_enb),.cpi(cpi_hb),
+      .stb_in(strobe_hb1),.data_in(i_hb1),.stb_out(strobe_hb2),.data_out(i_hb2));
+
+   hb_dec #(.WIDTH(WIDTH)) hb_q
+     (.clk(clk),.rst(rst),.bypass(~enable_hb2),.run(ddc_enb),.cpi(cpi_hb),
+      .stb_in(strobe_hb1),.data_in(q_hb1),.stb_out(),.data_out(q_hb2));
+
+   //scalar operation (gain of 6 bits)
+   wire [35:0] prod_i, prod_q;
+
+   MULT18X18S mult_i
+     (.P(prod_i), .A(i_hb2[WIDTH-1:WIDTH-18]), .B(scale_factor), .C(clk), .CE(strobe_hb2), .R(rst) );
+   MULT18X18S mult_q
+     (.P(prod_q), .A(q_hb2[WIDTH-1:WIDTH-18]), .B(scale_factor), .C(clk), .CE(strobe_hb2), .R(rst) );
+
+   //pipeline for the multiplier (gain of 10 bits)
+   reg [WIDTH-1:0] prod_reg_i, prod_reg_q;
+   reg strobe_mult;
+
+   always @(posedge clk) begin
+       strobe_mult <= strobe_hb2;
+       prod_reg_i <= prod_i[33:34-WIDTH];
+       prod_reg_q <= prod_q[33:34-WIDTH];
+   end
+
+   // Round final answer to 16 bits
+   wire [31:0] ddc_chain_out;
+   wire ddc_chain_stb;
+
+   round_sd #(.WIDTH_IN(WIDTH),.WIDTH_OUT(16)) round_i
+     (.clk(clk),.reset(rst), .in(prod_reg_i),.strobe_in(strobe_mult), .out(ddc_chain_out[31:16]), .strobe_out(ddc_chain_stb));
+
+   round_sd #(.WIDTH_IN(WIDTH),.WIDTH_OUT(16)) round_q
+     (.clk(clk),.reset(rst), .in(prod_reg_q),.strobe_in(strobe_mult), .out(ddc_chain_out[15:0]), .strobe_out());
+
+   dsp_rx_glue #(.DSPNO(DSPNO), .WIDTH(WIDTH)) custom(
+    .clock(clk), .reset(rst), .clear(clr), .enable(run),
+    .set_stb(set_stb_user), .set_addr(set_addr_user), .set_data(set_data_user),
+    .frontend_i(rx_fe_i_mux), .frontend_q(rx_fe_q_mux),
+    .ddc_in_i(to_ddc_chain_i), .ddc_in_q(to_ddc_chain_q),
+    .ddc_out_sample(ddc_chain_out), .ddc_out_strobe(ddc_chain_stb), .ddc_out_enable(ddc_enb),
+    .bb_sample(sample), .bb_strobe(strobe));
+
+   assign      debug = {enable_hb1, enable_hb2, run, strobe, strobe_cic, strobe_hb1, strobe_hb2};
+   
+endmodule // ddc_chain
diff --git a/fpga/usrp2/sdr_lib/dsp_core_rx.v b/fpga/usrp2/sdr_lib/dsp_core_rx.v
deleted file mode 100644
index d1c7e238a..000000000
--- a/fpga/usrp2/sdr_lib/dsp_core_rx.v
+++ /dev/null
@@ -1,144 +0,0 @@
-//
-// Copyright 2011 Ettus Research LLC
-//
-// This program is free software: you can redistribute it and/or modify
-// it under the terms of the GNU General Public License as published by
-// the Free Software Foundation, either version 3 of the License, or
-// (at your option) any later version.
-//
-// This program is distributed in the hope that it will be useful,
-// but WITHOUT ANY WARRANTY; without even the implied warranty of
-// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-// GNU General Public License for more details.
-//
-// You should have received a copy of the GNU General Public License
-// along with this program.  If not, see <http://www.gnu.org/licenses/>.
-//
-
-
-module dsp_core_rx
-  #(parameter BASE = 160)
-  (input clk, input rst,
-   input set_stb, input [7:0] set_addr, input [31:0] set_data,
-
-   input [23:0] adc_i, input adc_ovf_i,
-   input [23:0] adc_q, input adc_ovf_q,
-   
-   output [31:0] sample,
-   input run,
-   output strobe,
-   output [31:0] debug
-   );
-
-   wire [31:0] phase_inc;
-   reg [31:0]  phase;
-
-   wire [24:0] i_cordic, q_cordic;
-   wire [23:0] i_cordic_clip, q_cordic_clip;
-   wire [23:0] i_cic, q_cic;
-   wire [23:0] i_hb1, q_hb1;
-   wire [23:0] i_hb2, q_hb2;
-   
-   wire        strobe_cic, strobe_hb1, strobe_hb2;
-   wire        enable_hb1, enable_hb2;
-   wire [7:0]  cic_decim_rate;
-
-   reg [23:0]  adc_i_mux, adc_q_mux;
-   wire        realmode;
-   wire        swap_iq;
-   
-   setting_reg #(.my_addr(BASE+0)) sr_0
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out(phase_inc),.changed());
-   
-   /*
-   setting_reg #(.my_addr(BASE+1)) sr_1
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out({scale_i,scale_q}),.changed());
-   */
-   
-   setting_reg #(.my_addr(BASE+2), .width(10)) sr_2
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out({enable_hb1, enable_hb2, cic_decim_rate}),.changed());
-
-   setting_reg #(.my_addr(BASE+3), .width(2)) sr_3
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out({realmode,swap_iq}),.changed());
-
-   // MUX so we can do realmode signals on either input
-   
-   always @(posedge clk)
-     if(swap_iq)
-       begin
-	  adc_i_mux <= adc_q;
-	  adc_q_mux <= realmode ? 24'd0 : adc_i;
-       end
-     else
-       begin
-	  adc_i_mux <= adc_i;
-	  adc_q_mux <= realmode ? 24'd0 : adc_q;
-       end
-
-   // NCO
-   always @(posedge clk)
-     if(rst)
-       phase <= 0;
-     else if(~run)
-       phase <= 0;
-     else
-       phase <= phase + phase_inc;
-
-   // CORDIC  24-bit I/O
-   cordic_z24 #(.bitwidth(25))
-     cordic(.clock(clk), .reset(rst), .enable(run),
-	    .xi({adc_i_mux[23],adc_i_mux}),. yi({adc_q_mux[23],adc_q_mux}), .zi(phase[31:8]),
-	    .xo(i_cordic),.yo(q_cordic),.zo() );
-
-   clip_reg #(.bits_in(25), .bits_out(24)) clip_i
-     (.clk(clk), .in(i_cordic), .strobe_in(1'b1), .out(i_cordic_clip));
-   clip_reg #(.bits_in(25), .bits_out(24)) clip_q
-     (.clk(clk), .in(q_cordic), .strobe_in(1'b1), .out(q_cordic_clip));
-
-   // CIC decimator  24 bit I/O
-   cic_strober cic_strober(.clock(clk),.reset(rst),.enable(run),.rate(cic_decim_rate),
-			   .strobe_fast(1),.strobe_slow(strobe_cic) );
-
-   cic_decim #(.bw(24))
-     decim_i (.clock(clk),.reset(rst),.enable(run),
-	      .rate(cic_decim_rate),.strobe_in(1'b1),.strobe_out(strobe_cic),
-	      .signal_in(i_cordic_clip),.signal_out(i_cic));
-   
-   cic_decim #(.bw(24))
-     decim_q (.clock(clk),.reset(rst),.enable(run),
-	      .rate(cic_decim_rate),.strobe_in(1'b1),.strobe_out(strobe_cic),
-	      .signal_in(q_cordic_clip),.signal_out(q_cic));
-
-   // First (small) halfband  24 bit I/O
-   small_hb_dec #(.WIDTH(24)) small_hb_i
-     (.clk(clk),.rst(rst),.bypass(~enable_hb1),.run(run),
-      .stb_in(strobe_cic),.data_in(i_cic),.stb_out(strobe_hb1),.data_out(i_hb1));
-   
-   small_hb_dec #(.WIDTH(24)) small_hb_q
-     (.clk(clk),.rst(rst),.bypass(~enable_hb1),.run(run),
-      .stb_in(strobe_cic),.data_in(q_cic),.stb_out(),.data_out(q_hb1));
-
-   // Second (large) halfband  24 bit I/O
-   wire [8:0]  cpi_hb = enable_hb1 ? {cic_decim_rate,1'b0} : {1'b0,cic_decim_rate};
-   hb_dec #(.WIDTH(24)) hb_i
-     (.clk(clk),.rst(rst),.bypass(~enable_hb2),.run(run),.cpi(cpi_hb),
-      .stb_in(strobe_hb1),.data_in(i_hb1),.stb_out(strobe_hb2),.data_out(i_hb2));
-
-   hb_dec #(.WIDTH(24)) hb_q
-     (.clk(clk),.rst(rst),.bypass(~enable_hb2),.run(run),.cpi(cpi_hb),
-      .stb_in(strobe_hb1),.data_in(q_hb1),.stb_out(),.data_out(q_hb2));
-
-   // Round final answer to 16 bits
-   round_sd #(.WIDTH_IN(24),.WIDTH_OUT(16)) round_i
-     (.clk(clk),.reset(rst), .in(i_hb2),.strobe_in(strobe_hb2), .out(sample[31:16]), .strobe_out(strobe));
-
-   round_sd #(.WIDTH_IN(24),.WIDTH_OUT(16)) round_q
-     (.clk(clk),.reset(rst), .in(q_hb2),.strobe_in(strobe_hb2), .out(sample[15:0]), .strobe_out());
-   
-   assign      debug = {enable_hb1, enable_hb2, run, strobe, strobe_cic, strobe_hb1, strobe_hb2};
-   
-endmodule // dsp_core_rx
diff --git a/fpga/usrp2/sdr_lib/dsp_core_rx_old.v b/fpga/usrp2/sdr_lib/dsp_core_rx_old.v
deleted file mode 100644
index 90d5d839f..000000000
--- a/fpga/usrp2/sdr_lib/dsp_core_rx_old.v
+++ /dev/null
@@ -1,200 +0,0 @@
-//
-// Copyright 2011 Ettus Research LLC
-//
-// This program is free software: you can redistribute it and/or modify
-// it under the terms of the GNU General Public License as published by
-// the Free Software Foundation, either version 3 of the License, or
-// (at your option) any later version.
-//
-// This program is distributed in the hope that it will be useful,
-// but WITHOUT ANY WARRANTY; without even the implied warranty of
-// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-// GNU General Public License for more details.
-//
-// You should have received a copy of the GNU General Public License
-// along with this program.  If not, see <http://www.gnu.org/licenses/>.
-//
-
-
-`define DSP_CORE_RX_BASE 160
-module dsp_core_rx_old
-  (input clk, input rst,
-   input set_stb, input [7:0] set_addr, input [31:0] set_data,
-
-   input [13:0] adc_a, input adc_ovf_a,
-   input [13:0] adc_b, input adc_ovf_b,
-   
-   input [15:0] io_rx,
-
-   output [31:0] sample,
-   input run,
-   output strobe,
-   output [31:0] debug
-   );
-
-   wire [15:0] scale_i, scale_q;
-   wire [13:0] adc_a_ofs, adc_b_ofs;
-   reg [13:0] adc_i, adc_q;
-   wire [31:0] phase_inc;
-   reg [31:0]  phase;
-
-   wire [35:0] prod_i, prod_q;
-   wire [23:0] i_cordic, q_cordic;
-   wire [23:0] i_cic, q_cic;
-   wire [17:0] i_cic_scaled, q_cic_scaled;
-   wire [17:0] i_hb1, q_hb1;
-   wire [17:0] i_hb2, q_hb2;
-   wire [15:0] i_out, q_out;
-
-   wire        strobe_cic, strobe_hb1, strobe_hb2;
-   wire        enable_hb1, enable_hb2;
-   wire [7:0]  cic_decim_rate;
-
-   wire [31:10] UNUSED_1;
-   wire [31:4] 	UNUSED_2;
-   wire [31:2] 	UNUSED_3;
-   
-   setting_reg #(.my_addr(`DSP_CORE_RX_BASE+0)) sr_0
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out(phase_inc),.changed());
-   
-   setting_reg #(.my_addr(`DSP_CORE_RX_BASE+1)) sr_1
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out({scale_i,scale_q}),.changed());
-   
-   setting_reg #(.my_addr(`DSP_CORE_RX_BASE+2)) sr_2
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out({UNUSED_1, enable_hb1, enable_hb2, cic_decim_rate}),.changed());
-
-   rx_dcoffset #(.WIDTH(14),.ADDR(`DSP_CORE_RX_BASE+6)) rx_dcoffset_a
-     (.clk(clk),.rst(rst),.set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
-      .adc_in(adc_a),.adc_out(adc_a_ofs));
-   
-   rx_dcoffset #(.WIDTH(14),.ADDR(`DSP_CORE_RX_BASE+7)) rx_dcoffset_b
-     (.clk(clk),.rst(rst),.set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
-      .adc_in(adc_b),.adc_out(adc_b_ofs));
-
-   wire [3:0]  muxctrl;
-   setting_reg #(.my_addr(`DSP_CORE_RX_BASE+8)) sr_8
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out({UNUSED_2,muxctrl}),.changed());
-
-   wire [1:0] gpio_ena;
-   setting_reg #(.my_addr(`DSP_CORE_RX_BASE+9)) sr_9
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out({UNUSED_3,gpio_ena}),.changed());
-
-   // The TVRX connects to what is called adc_b, thus A and B are
-   // swapped throughout the design.
-   //
-   // In the interest of expediency and keeping the s/w sane, we just remap them here.
-   // The I & Q fields are mapped the same:
-   // 0 -> "the real A" (as determined by the TVRX)
-   // 1 -> "the real B"
-   // 2 -> const zero
-   
-   always @(posedge clk)
-     case(muxctrl[1:0])		// The I mapping
-       0: adc_i <= adc_b_ofs;	// "the real A"
-       1: adc_i <= adc_a_ofs;
-       2: adc_i <= 0;
-       default: adc_i <= 0;
-     endcase // case(muxctrl[1:0])
-          
-   always @(posedge clk)
-     case(muxctrl[3:2])		// The Q mapping
-       0: adc_q <= adc_b_ofs;	// "the real A"
-       1: adc_q <= adc_a_ofs;
-       2: adc_q <= 0;
-       default: adc_q <= 0;
-     endcase // case(muxctrl[3:2])
-       
-   always @(posedge clk)
-     if(rst)
-       phase <= 0;
-     else if(~run)
-       phase <= 0;
-     else
-       phase <= phase + phase_inc;
-
-   MULT18X18S mult_i
-     (.P(prod_i),    // 36-bit multiplier output
-      .A({{4{adc_i[13]}},adc_i} ),    // 18-bit multiplier input
-      .B({{2{scale_i[15]}},scale_i}),    // 18-bit multiplier input
-      .C(clk),    // Clock input
-      .CE(1),  // Clock enable input
-      .R(rst)     // Synchronous reset input
-      );
-
-   MULT18X18S mult_q
-     (.P(prod_q),    // 36-bit multiplier output
-      .A({{4{adc_q[13]}},adc_q} ),    // 18-bit multiplier input
-      .B({{2{scale_q[15]}},scale_q}),    // 18-bit multiplier input
-      .C(clk),    // Clock input
-      .CE(1),  // Clock enable input
-      .R(rst)     // Synchronous reset input
-      ); 
-
-   
-   cordic_z24 #(.bitwidth(24))
-     cordic(.clock(clk), .reset(rst), .enable(run),
-	    .xi(prod_i[23:0]),. yi(prod_q[23:0]), .zi(phase[31:8]),
-	    .xo(i_cordic),.yo(q_cordic),.zo() );
-
-   cic_strober cic_strober(.clock(clk),.reset(rst),.enable(run),.rate(cic_decim_rate),
-			   .strobe_fast(1),.strobe_slow(strobe_cic) );
-
-   cic_decim #(.bw(24))
-     decim_i (.clock(clk),.reset(rst),.enable(run),
-	      .rate(cic_decim_rate),.strobe_in(1'b1),.strobe_out(strobe_cic),
-	      .signal_in(i_cordic),.signal_out(i_cic));
-   
-   cic_decim #(.bw(24))
-     decim_q (.clock(clk),.reset(rst),.enable(run),
-	      .rate(cic_decim_rate),.strobe_in(1'b1),.strobe_out(strobe_cic),
-	      .signal_in(q_cordic),.signal_out(q_cic));
-
-   round_reg #(.bits_in(24),.bits_out(18)) round_icic (.clk(clk),.in(i_cic),.out(i_cic_scaled));
-   round_reg #(.bits_in(24),.bits_out(18)) round_qcic (.clk(clk),.in(q_cic),.out(q_cic_scaled));
-   reg 	       strobe_cic_d1;
-   always @(posedge clk) strobe_cic_d1 <= strobe_cic;
-   
-   small_hb_dec #(.WIDTH(18)) small_hb_i
-     (.clk(clk),.rst(rst),.bypass(~enable_hb1),.run(run),
-      .stb_in(strobe_cic_d1),.data_in(i_cic_scaled),.stb_out(strobe_hb1),.data_out(i_hb1));
-   
-   small_hb_dec #(.WIDTH(18)) small_hb_q
-     (.clk(clk),.rst(rst),.bypass(~enable_hb1),.run(run),
-      .stb_in(strobe_cic_d1),.data_in(q_cic_scaled),.stb_out(),.data_out(q_hb1));
-
-   wire [8:0]  cpi_hb = enable_hb1 ? {cic_decim_rate,1'b0} : {1'b0,cic_decim_rate};
-   hb_dec #(.IWIDTH(18), .OWIDTH(18), .CWIDTH(18), .ACCWIDTH(24)) hb_i
-     (.clk(clk),.rst(rst),.bypass(~enable_hb2),.run(run),.cpi(cpi_hb),
-      .stb_in(strobe_hb1),.data_in(i_hb1),.stb_out(strobe_hb2),.data_out(i_hb2));
-
-   hb_dec #(.IWIDTH(18), .OWIDTH(18), .CWIDTH(18), .ACCWIDTH(24)) hb_q
-     (.clk(clk),.rst(rst),.bypass(~enable_hb2),.run(run),.cpi(cpi_hb),
-      .stb_in(strobe_hb1),.data_in(q_hb1),.stb_out(),.data_out(q_hb2));
-
-   round #(.bits_in(18),.bits_out(16)) round_iout (.in(i_hb2),.out(i_out));
-   round #(.bits_in(18),.bits_out(16)) round_qout (.in(q_hb2),.out(q_out));
-
-   // Streaming GPIO
-   //
-   // io_rx[15] => I channel LSB if gpio_ena[0] high
-   // io_rx[14] => Q channel LSB if gpio_ena[1] high
-
-   reg [31:0] sample_reg;
-   always @(posedge clk)
-     begin
-	sample_reg[31:17] <= i_out[15:1];
-	sample_reg[15:1]  <= q_out[15:1];
-	sample_reg[16]    <= gpio_ena[0] ? io_rx[15] : i_out[0]; 
-	sample_reg[0]     <= gpio_ena[1] ? io_rx[14] : q_out[0];
-     end
-   
-   assign      sample = sample_reg;
-   assign      strobe = strobe_hb2;
-   assign      debug = {enable_hb1, enable_hb2, run, strobe, strobe_cic, strobe_cic_d1, strobe_hb1, strobe_hb2};
-   
-endmodule // dsp_core_rx
diff --git a/fpga/usrp2/sdr_lib/dsp_core_rx_tb.v b/fpga/usrp2/sdr_lib/dsp_core_rx_tb.v
index 271db8cef..a221bed44 100644
--- a/fpga/usrp2/sdr_lib/dsp_core_rx_tb.v
+++ b/fpga/usrp2/sdr_lib/dsp_core_rx_tb.v
@@ -1,6 +1,6 @@
 
 `timescale 1ns/1ns
-module dsp_core_rx_tb();
+module ddc_chain_tb();
    
    reg clk, rst;
 
@@ -9,8 +9,8 @@ module dsp_core_rx_tb();
    initial clk = 0;
    always #5 clk = ~clk;
    
-   initial $dumpfile("dsp_core_rx_tb.vcd");
-   initial $dumpvars(0,dsp_core_rx_tb);
+   initial $dumpfile("ddc_chain_tb.vcd");
+   initial $dumpvars(0,ddc_chain_tb);
    
    reg signed [23:0] adc_in;
    wire signed [15:0] adc_out_i, adc_out_q;
@@ -27,7 +27,7 @@ module dsp_core_rx_tb();
    reg [7:0] set_addr;
    reg [31:0] set_data;
    
-   dsp_core_rx #(.BASE(0)) dsp_core_rx
+   ddc_chain #(.BASE(0)) ddc_chain
      (.clk(clk),.rst(rst),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
       .adc_i(adc_in), .adc_ovf_i(0),
@@ -70,4 +70,4 @@ module dsp_core_rx_tb();
        adc_in <= adc_in + 4;
    //adc_in <= (($random % 473) + 23)/4;
 */   
-endmodule // dsp_core_rx_tb
+endmodule // ddc_chain_tb
diff --git a/fpga/usrp2/sdr_lib/dsp_core_rx_udp.v b/fpga/usrp2/sdr_lib/dsp_core_rx_udp.v
deleted file mode 100644
index 08dab37e6..000000000
--- a/fpga/usrp2/sdr_lib/dsp_core_rx_udp.v
+++ /dev/null
@@ -1,200 +0,0 @@
-//
-// Copyright 2011 Ettus Research LLC
-//
-// This program is free software: you can redistribute it and/or modify
-// it under the terms of the GNU General Public License as published by
-// the Free Software Foundation, either version 3 of the License, or
-// (at your option) any later version.
-//
-// This program is distributed in the hope that it will be useful,
-// but WITHOUT ANY WARRANTY; without even the implied warranty of
-// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-// GNU General Public License for more details.
-//
-// You should have received a copy of the GNU General Public License
-// along with this program.  If not, see <http://www.gnu.org/licenses/>.
-//
-
-
-module dsp_core_rx
-  #(parameter BASE = 160)
-  (input clk, input rst,
-   input set_stb, input [7:0] set_addr, input [31:0] set_data,
-
-   input [13:0] adc_a, input adc_ovf_a,
-   input [13:0] adc_b, input adc_ovf_b,
-   
-   input [15:0] io_rx,
-
-   output [31:0] sample,
-   input run,
-   output strobe,
-   output [31:0] debug
-   );
-
-   wire [15:0] scale_i, scale_q;
-   wire [13:0] adc_a_ofs, adc_b_ofs;
-   reg [13:0] adc_i, adc_q;
-   wire [31:0] phase_inc;
-   reg [31:0]  phase;
-
-   wire [35:0] prod_i, prod_q;
-   wire [23:0] i_cordic, q_cordic;
-   wire [23:0] i_cic, q_cic;
-   wire [17:0] i_cic_scaled, q_cic_scaled;
-   wire [17:0] i_hb1, q_hb1;
-   wire [17:0] i_hb2, q_hb2;
-   wire [15:0] i_out, q_out;
-
-   wire        strobe_cic, strobe_hb1, strobe_hb2;
-   wire        enable_hb1, enable_hb2;
-   wire [7:0]  cic_decim_rate;
-
-   wire [31:10] UNUSED_1;
-   wire [31:4] 	UNUSED_2;
-   wire [31:2] 	UNUSED_3;
-   
-   setting_reg #(.my_addr(BASE+0)) sr_0
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out(phase_inc),.changed());
-   
-   setting_reg #(.my_addr(BASE+1)) sr_1
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out({scale_i,scale_q}),.changed());
-   
-   setting_reg #(.my_addr(BASE+2)) sr_2
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out({UNUSED_1, enable_hb1, enable_hb2, cic_decim_rate}),.changed());
-
-   rx_dcoffset #(.WIDTH(14),.ADDR(BASE+3)) rx_dcoffset_a
-     (.clk(clk),.rst(rst),.set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
-      .adc_in(adc_a),.adc_out(adc_a_ofs));
-   
-   rx_dcoffset #(.WIDTH(14),.ADDR(BASE+4)) rx_dcoffset_b
-     (.clk(clk),.rst(rst),.set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
-      .adc_in(adc_b),.adc_out(adc_b_ofs));
-
-   wire [3:0]  muxctrl;
-   setting_reg #(.my_addr(BASE+5)) sr_8
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out({UNUSED_2,muxctrl}),.changed());
-
-   wire [1:0] gpio_ena;
-   setting_reg #(.my_addr(BASE+6)) sr_9
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out({UNUSED_3,gpio_ena}),.changed());
-
-   // The TVRX connects to what is called adc_b, thus A and B are
-   // swapped throughout the design.
-   //
-   // In the interest of expediency and keeping the s/w sane, we just remap them here.
-   // The I & Q fields are mapped the same:
-   // 0 -> "the real A" (as determined by the TVRX)
-   // 1 -> "the real B"
-   // 2 -> const zero
-   
-   always @(posedge clk)
-     case(muxctrl[1:0])		// The I mapping
-       0: adc_i <= adc_b_ofs;	// "the real A"
-       1: adc_i <= adc_a_ofs;
-       2: adc_i <= 0;
-       default: adc_i <= 0;
-     endcase // case(muxctrl[1:0])
-          
-   always @(posedge clk)
-     case(muxctrl[3:2])		// The Q mapping
-       0: adc_q <= adc_b_ofs;	// "the real A"
-       1: adc_q <= adc_a_ofs;
-       2: adc_q <= 0;
-       default: adc_q <= 0;
-     endcase // case(muxctrl[3:2])
-       
-   always @(posedge clk)
-     if(rst)
-       phase <= 0;
-     else if(~run)
-       phase <= 0;
-     else
-       phase <= phase + phase_inc;
-
-   MULT18X18S mult_i
-     (.P(prod_i),    // 36-bit multiplier output
-      .A({{4{adc_i[13]}},adc_i} ),    // 18-bit multiplier input
-      .B({{2{scale_i[15]}},scale_i}),    // 18-bit multiplier input
-      .C(clk),    // Clock input
-      .CE(1),  // Clock enable input
-      .R(rst)     // Synchronous reset input
-      );
-
-   MULT18X18S mult_q
-     (.P(prod_q),    // 36-bit multiplier output
-      .A({{4{adc_q[13]}},adc_q} ),    // 18-bit multiplier input
-      .B({{2{scale_q[15]}},scale_q}),    // 18-bit multiplier input
-      .C(clk),    // Clock input
-      .CE(1),  // Clock enable input
-      .R(rst)     // Synchronous reset input
-      ); 
-
-   
-   cordic_z24 #(.bitwidth(24))
-     cordic(.clock(clk), .reset(rst), .enable(run),
-	    .xi(prod_i[23:0]),. yi(prod_q[23:0]), .zi(phase[31:8]),
-	    .xo(i_cordic),.yo(q_cordic),.zo() );
-
-   cic_strober cic_strober(.clock(clk),.reset(rst),.enable(run),.rate(cic_decim_rate),
-			   .strobe_fast(1),.strobe_slow(strobe_cic) );
-
-   cic_decim #(.bw(24))
-     decim_i (.clock(clk),.reset(rst),.enable(run),
-	      .rate(cic_decim_rate),.strobe_in(1'b1),.strobe_out(strobe_cic),
-	      .signal_in(i_cordic),.signal_out(i_cic));
-   
-   cic_decim #(.bw(24))
-     decim_q (.clock(clk),.reset(rst),.enable(run),
-	      .rate(cic_decim_rate),.strobe_in(1'b1),.strobe_out(strobe_cic),
-	      .signal_in(q_cordic),.signal_out(q_cic));
-
-   round_reg #(.bits_in(24),.bits_out(18)) round_icic (.clk(clk),.in(i_cic),.out(i_cic_scaled));
-   round_reg #(.bits_in(24),.bits_out(18)) round_qcic (.clk(clk),.in(q_cic),.out(q_cic_scaled));
-   reg 	       strobe_cic_d1;
-   always @(posedge clk) strobe_cic_d1 <= strobe_cic;
-   
-   small_hb_dec #(.WIDTH(18)) small_hb_i
-     (.clk(clk),.rst(rst),.bypass(~enable_hb1),.run(run),
-      .stb_in(strobe_cic_d1),.data_in(i_cic_scaled),.stb_out(strobe_hb1),.data_out(i_hb1));
-   
-   small_hb_dec #(.WIDTH(18)) small_hb_q
-     (.clk(clk),.rst(rst),.bypass(~enable_hb1),.run(run),
-      .stb_in(strobe_cic_d1),.data_in(q_cic_scaled),.stb_out(),.data_out(q_hb1));
-
-   wire [8:0]  cpi_hb = enable_hb1 ? {cic_decim_rate,1'b0} : {1'b0,cic_decim_rate};
-   hb_dec #(.IWIDTH(18), .OWIDTH(18), .CWIDTH(18), .ACCWIDTH(24)) hb_i
-     (.clk(clk),.rst(rst),.bypass(~enable_hb2),.run(run),.cpi(cpi_hb),
-      .stb_in(strobe_hb1),.data_in(i_hb1),.stb_out(strobe_hb2),.data_out(i_hb2));
-
-   hb_dec #(.IWIDTH(18), .OWIDTH(18), .CWIDTH(18), .ACCWIDTH(24)) hb_q
-     (.clk(clk),.rst(rst),.bypass(~enable_hb2),.run(run),.cpi(cpi_hb),
-      .stb_in(strobe_hb1),.data_in(q_hb1),.stb_out(),.data_out(q_hb2));
-
-   round #(.bits_in(18),.bits_out(16)) round_iout (.in(i_hb2),.out(i_out));
-   round #(.bits_in(18),.bits_out(16)) round_qout (.in(q_hb2),.out(q_out));
-
-   // Streaming GPIO
-   //
-   // io_rx[15] => I channel LSB if gpio_ena[0] high
-   // io_rx[14] => Q channel LSB if gpio_ena[1] high
-
-   reg [31:0] sample_reg;
-   always @(posedge clk)
-     begin
-	sample_reg[31:17] <= i_out[15:1];
-	sample_reg[15:1]  <= q_out[15:1];
-	sample_reg[16]    <= gpio_ena[0] ? io_rx[15] : i_out[0]; 
-	sample_reg[0]     <= gpio_ena[1] ? io_rx[14] : q_out[0];
-     end
-   
-   assign      sample = sample_reg;
-   assign      strobe = strobe_hb2;
-   assign      debug = {enable_hb1, enable_hb2, run, strobe, strobe_cic, strobe_cic_d1, strobe_hb1, strobe_hb2};
-   
-endmodule // dsp_core_rx
diff --git a/fpga/usrp2/sdr_lib/dsp_rx_glue.v b/fpga/usrp2/sdr_lib/dsp_rx_glue.v
new file mode 100644
index 000000000..038a67a29
--- /dev/null
+++ b/fpga/usrp2/sdr_lib/dsp_rx_glue.v
@@ -0,0 +1,98 @@
+//
+// Copyright 2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+//The following module effects the IO of the DDC chain.
+//By default, this entire module is a simple pass-through.
+
+module dsp_rx_glue
+#(
+    //the dsp unit number: 0, 1, 2...
+    parameter DSPNO = 0,
+
+    //frontend bus width
+    parameter WIDTH = 24
+)
+(
+    //control signals
+    input clock, input reset, input clear, input enable,
+
+    //user settings bus, controlled through user setting regs API
+    input set_stb, input [7:0] set_addr, input [31:0] set_data,
+
+    //full rate inputs directly from the RX frontend
+    input [WIDTH-1:0] frontend_i,
+    input [WIDTH-1:0] frontend_q,
+
+    //full rate outputs directly to the DDC chain
+    output [WIDTH-1:0] ddc_in_i,
+    output [WIDTH-1:0] ddc_in_q,
+
+    //strobed samples {I16,Q16} from the RX DDC chain
+    input [31:0] ddc_out_sample,
+    input ddc_out_strobe, //high on valid sample
+    output ddc_out_enable, //enables DDC module
+
+    //strobbed baseband samples {I16,Q16} from this module
+    output [31:0] bb_sample,
+    output bb_strobe, //high on valid sample
+
+    //debug output (optional)
+    output [31:0] debug
+);
+
+    generate
+        if (DSPNO==0) begin
+            `ifndef RX_DSP0_MODULE
+            assign ddc_in_i = frontend_i;
+            assign ddc_in_q = frontend_q;
+            assign bb_sample = ddc_out_sample;
+            assign bb_strobe = ddc_out_strobe;
+            assign ddc_out_enable = enable;
+            `else
+            `RX_DSP0_MODULE #(.WIDTH(WIDTH)) rx_dsp0_custom
+            (
+                .clock(clock), .reset(reset), .clear(clear), .enable(enable),
+                .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
+                .frontend_i(frontend_i), .frontend_q(frontend_q),
+                .ddc_in_i(ddc_in_i), .ddc_in_q(ddc_in_q),
+                .ddc_out_sample(ddc_out_sample), .ddc_out_strobe(ddc_out_strobe), .ddc_out_enable(ddc_out_enable),
+                .bb_sample(bb_sample), .bb_strobe(bb_strobe)
+            );
+            `endif
+        end
+        else begin
+            `ifndef RX_DSP1_MODULE
+            assign ddc_in_i = frontend_i;
+            assign ddc_in_q = frontend_q;
+            assign bb_sample = ddc_out_sample;
+            assign bb_strobe = ddc_out_strobe;
+            assign ddc_out_enable = enable;
+            `else
+            `RX_DSP1_MODULE #(.WIDTH(WIDTH)) rx_dsp1_custom
+            (
+                .clock(clock), .reset(reset), .clear(clear), .enable(enable),
+                .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
+                .frontend_i(frontend_i), .frontend_q(frontend_q),
+                .ddc_in_i(ddc_in_i), .ddc_in_q(ddc_in_q),
+                .ddc_out_sample(ddc_out_sample), .ddc_out_strobe(ddc_out_strobe), .ddc_out_enable(ddc_out_enable),
+                .bb_sample(bb_sample), .bb_strobe(bb_strobe)
+            );
+            `endif
+        end
+    endgenerate
+
+endmodule //dsp_rx_glue
diff --git a/fpga/usrp2/sdr_lib/dsp_tx_glue.v b/fpga/usrp2/sdr_lib/dsp_tx_glue.v
new file mode 100644
index 000000000..46f6789ee
--- /dev/null
+++ b/fpga/usrp2/sdr_lib/dsp_tx_glue.v
@@ -0,0 +1,98 @@
+//
+// Copyright 2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+//The following module effects the IO of the DUC chain.
+//By default, this entire module is a simple pass-through.
+
+module dsp_tx_glue
+#(
+    //the dsp unit number: 0, 1, 2...
+    parameter DSPNO = 0,
+
+    //frontend bus width
+    parameter WIDTH = 24
+)
+(
+    //control signals
+    input clock, input reset, input clear, input enable,
+
+    //user settings bus, controlled through user setting regs API
+    input set_stb, input [7:0] set_addr, input [31:0] set_data,
+
+    //full rate outputs directly to the TX frontend
+    output [WIDTH-1:0] frontend_i,
+    output [WIDTH-1:0] frontend_q,
+
+    //full rate outputs directly from the DUC chain
+    input [WIDTH-1:0] duc_out_i,
+    input [WIDTH-1:0] duc_out_q,
+
+    //strobed samples {I16,Q16} to the TX DUC chain
+    output [31:0] duc_in_sample,
+    input duc_in_strobe, //this is a backpressure signal
+    output duc_in_enable, //enables DUC module
+
+    //strobbed baseband samples {I16,Q16} to this module
+    input [31:0] bb_sample,
+    output bb_strobe, //this is a backpressure signal
+
+    //debug output (optional)
+    output [31:0] debug
+);
+
+    generate
+        if (DSPNO==0) begin
+            `ifndef TX_DSP0_MODULE
+            assign frontend_i = duc_out_i;
+            assign frontend_q = duc_out_q;
+            assign duc_in_sample = bb_sample;
+            assign bb_strobe = duc_in_strobe;
+            assign duc_in_enable = enable;
+            `else
+            `TX_DSP0_MODULE #(.WIDTH(WIDTH)) tx_dsp0_custom
+            (
+                .clock(clock), .reset(reset), .clear(clear), .enable(enable),
+                .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
+                .frontend_i(frontend_i), .frontend_q(frontend_q),
+                .duc_out_i(duc_out_i), .duc_out_q(duc_out_q),
+                .duc_in_sample(duc_in_sample), .duc_in_strobe(duc_in_strobe), .duc_in_enable(duc_in_enable),
+                .bb_sample(bb_sample), .bb_strobe(bb_strobe)
+            );
+            `endif
+        end
+        else begin
+            `ifndef TX_DSP1_MODULE
+            assign frontend_i = duc_out_i;
+            assign frontend_q = duc_out_q;
+            assign duc_in_sample = bb_sample;
+            assign bb_strobe = duc_in_strobe;
+            assign duc_in_enable = enable;
+            `else
+            `TX_DSP1_MODULE #(.WIDTH(WIDTH)) tx_dsp1_custom
+            (
+                .clock(clock), .reset(reset), .clear(clear), .enable(enable),
+                .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
+                .frontend_i(frontend_i), .frontend_q(frontend_q),
+                .duc_out_i(duc_out_i), .duc_out_q(duc_out_q),
+                .duc_in_sample(duc_in_sample), .duc_in_strobe(duc_in_strobe), .duc_in_enable(duc_in_enable),
+                .bb_sample(bb_sample), .bb_strobe(bb_strobe)
+            );
+            `endif
+        end
+    endgenerate
+
+endmodule //dsp_tx_glue
diff --git a/fpga/usrp2/sdr_lib/dspengine_16to8.v b/fpga/usrp2/sdr_lib/dspengine_16to8.v
index 53c5d29da..448c57d35 100644
--- a/fpga/usrp2/sdr_lib/dspengine_16to8.v
+++ b/fpga/usrp2/sdr_lib/dspengine_16to8.v
@@ -1,5 +1,5 @@
 
-// Copyright 2011 Ettus Research LLC
+// Copyright 2011-2012 Ettus Research LLC
 //
 // This program is free software: you can redistribute it and/or modify
 // it under the terms of the GNU General Public License as published by
@@ -32,13 +32,11 @@ module dspengine_16to8
     input [35:0] access_dat_i
     );
 
-   wire 	 convert;
-   wire [17:0] 	 scale_factor;
-   
-   setting_reg #(.my_addr(BASE),.width(19)) sr_16to8
+   wire convert;
+   setting_reg #(.my_addr(BASE),.width(1)) sr_16to8
      (.clk(clk),.rst(reset),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out({convert,scale_factor}),.changed());
-   
+      .in(set_data),.out(convert),.changed());
+
    reg [2:0] 	 dsp_state;
    localparam DSP_IDLE = 0;
    localparam DSP_PARSE_HEADER = 1;
@@ -63,7 +61,7 @@ module dspengine_16to8
    wire [15:0] 	 scaled_i, scaled_q;
    wire [7:0] 	 i8, q8;
    reg [7:0] 	 i8_reg, q8_reg;
-   wire 	 stb_read, stb_mult, stb_clip, stb_round, val_read, val_mult, val_clip, val_round;
+   wire 	 stb_read, stb_clip, val_read, val_clip;
    wire 	 stb_out, stb_reg;
    reg 		 even;
    
@@ -193,29 +191,21 @@ module dspengine_16to8
    wire [15:0] i16 = access_dat_i[31:16];
    wire [15:0] q16 = access_dat_i[15:0];
 
-   pipectrl #(.STAGES(4), .TAGWIDTH(2)) pipectrl 
+   pipectrl #(.STAGES(2), .TAGWIDTH(2)) pipectrl
      (.clk(clk), .reset(reset),
       .src_rdy_i(send_to_pipe), .dst_rdy_o(), // dst_rdy_o will always be 1 since dst_rdy_i is 1, below
       .src_rdy_o(stb_out), .dst_rdy_i(1),   // always accept output of chain
-      .strobes({stb_round,stb_clip,stb_mult,stb_read}), .valids({val_round,val_clip,val_mult,val_read}),
+      .strobes({stb_clip,stb_read}), .valids({val_clip,val_read}),
       .tag_i({last,even}), .tag_o({last_o,even_o}));
 
    always @(posedge clk)
      if(stb_out & ~even_o)
        {i8_reg,q8_reg} <= {i8,q8};
-   
-   MULT18X18S mult_i 
-     (.P(prod_i), .A(scale_factor), .B({i16,2'b00}), .C(clk), .CE(stb_mult), .R(reset) ); 
-   clip_reg #(.bits_in(24),.bits_out(16),.STROBED(1)) clip_i 
-     (.clk(clk), .in(prod_i[35:12]), .out(scaled_i), .strobe_in(stb_clip), .strobe_out());
-   round_sd #(.WIDTH_IN(16),.WIDTH_OUT(8),.DISABLE_SD(1)) round_i
-     (.clk(clk), .reset(reset), .in(scaled_i), .strobe_in(stb_round), .out(i8), .strobe_out());
-
-   MULT18X18S mult_q 
-     (.P(prod_q), .A(scale_factor), .B({q16,2'b00}), .C(clk), .CE(stb_mult), .R(reset) ); 
-   clip_reg #(.bits_in(24),.bits_out(16),.STROBED(1)) clip_q 
-     (.clk(clk), .in(prod_q[35:12]), .out(scaled_q), .strobe_in(stb_clip), .strobe_out());
-   round_sd #(.WIDTH_IN(16),.WIDTH_OUT(8),.DISABLE_SD(1)) round_q
-     (.clk(clk), .reset(reset), .in(scaled_q), .strobe_in(stb_round), .out(q8), .strobe_out());
+
+   clip_reg #(.bits_in(16),.bits_out(8),.STROBED(1)) clip_i
+     (.clk(clk), .in(i16), .out(i8), .strobe_in(stb_clip), .strobe_out());
+
+   clip_reg #(.bits_in(16),.bits_out(8),.STROBED(1)) clip_q
+     (.clk(clk), .in(q16), .out(q8), .strobe_in(stb_clip), .strobe_out());
 
 endmodule // dspengine_16to8
diff --git a/fpga/usrp2/sdr_lib/dspengine_8to16.v b/fpga/usrp2/sdr_lib/dspengine_8to16.v
new file mode 100644
index 000000000..85187d78d
--- /dev/null
+++ b/fpga/usrp2/sdr_lib/dspengine_8to16.v
@@ -0,0 +1,203 @@
+
+// Copyright 2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+module dspengine_8to16
+  #(parameter BASE = 0,
+    parameter BUF_SIZE = 9,
+    parameter HEADER_OFFSET = 0)
+   (input clk, input reset, input clear,
+    input set_stb, input [7:0] set_addr, input [31:0] set_data,
+
+    output access_we,
+    output access_stb,
+    input access_ok,
+    output access_done,
+    output access_skip_read,
+    output [BUF_SIZE-1:0] access_adr,
+    input [BUF_SIZE-1:0] access_len,
+    output [35:0] access_dat_o,
+    input [35:0] access_dat_i
+    );
+
+   wire 	 convert;
+   
+   setting_reg #(.my_addr(BASE),.width(1)) sr_8to16
+     (.clk(clk),.rst(reset),.strobe(set_stb),.addr(set_addr),
+      .in(set_data),.out(convert),.changed());
+   
+   reg [3:0] 	 dsp_state;
+   localparam DSP_IDLE = 0;
+   localparam DSP_IDLE_RD = 1;
+   localparam DSP_PARSE_HEADER = 2;
+   localparam DSP_READ = 3;
+   localparam DSP_READ_WAIT = 4;
+   localparam DSP_WRITE_1 = 5;
+   localparam DSP_WRITE_0 = 6;
+   localparam DSP_READ_TRAILER = 7;
+   localparam DSP_WRITE_TRAILER = 8;
+   localparam DSP_WRITE_HEADER = 9;
+   localparam DSP_DONE = 10;
+   
+   // Parse VITA header
+   wire 	 is_if_data = (access_dat_i[31:29] == 3'b000);
+   wire 	 has_streamid = access_dat_i[28];
+   wire 	 has_classid = access_dat_i[27];
+   wire 	 has_trailer = access_dat_i[26];
+   // 25:24 reserved, aka SOB/EOB
+   wire 	 has_secs = |access_dat_i[23:22];
+   wire 	 has_tics = |access_dat_i[21:20];
+   wire [3:0] 	 hdr_length = 1 + has_streamid + has_classid + has_classid + has_secs + has_tics + has_tics;
+   reg [15:0] 	 hdr_length_reg;
+ 	 
+   reg 		 odd;
+   
+   reg [BUF_SIZE-1:0] read_adr, write_adr;
+   reg 		      has_trailer_reg;
+   
+   reg [31:0] 	      new_header, new_trailer, trailer_mask;
+   reg 		      wait_for_trailer;
+   reg [15:0] 	      data_in_len;
+   wire       	      is_odd = access_dat_i[22] & access_dat_i[10];
+   wire [15:0] 	      data_in_lenx2 = {data_in_len[14:0], 1'b0} - is_odd;
+
+   reg [7:0] 	      i8_0, q8_0;
+   wire [7:0] 	      i8_1 = access_dat_i[31:24];
+   wire [7:0] 	      q8_1 = access_dat_i[23:16];
+   reg 		      skip;
+   
+
+   always @(posedge clk)
+     { i8_0, q8_0 } <= access_dat_i[15:0];
+   
+   always @(posedge clk)
+     if(reset | clear)
+       dsp_state <= DSP_IDLE;
+     else
+       case(dsp_state)
+	 DSP_IDLE :
+	   begin
+	      read_adr <= HEADER_OFFSET;
+	      write_adr <= HEADER_OFFSET;
+	      if(access_ok)
+		dsp_state <= DSP_IDLE_RD;
+	   end
+
+	 DSP_IDLE_RD: //extra idle state for read to become valid
+		dsp_state <= DSP_PARSE_HEADER;
+
+	 DSP_PARSE_HEADER :
+	   begin
+	      has_trailer_reg <= has_trailer;
+	      new_header[31:0] <= access_dat_i[31:0];
+	      hdr_length_reg <= hdr_length;
+	      if(~is_if_data | ~convert | ~has_trailer)
+		// ~convert is valid (16 bit mode) but both ~trailer and ~is_if_data are both
+		// really error conditions on the TX side.  We shouldn't ever see them in the TX chain
+		dsp_state <= DSP_WRITE_HEADER;  
+	      else
+		begin
+		   read_adr <= access_dat_i[15:0] + HEADER_OFFSET - 1; // point to trailer
+		   dsp_state <= DSP_READ_TRAILER;
+		   wait_for_trailer <= 0;
+		   data_in_len <= access_dat_i[15:0] - hdr_length - 1 /*trailer*/;
+		end
+	   end
+	 
+	 DSP_READ_TRAILER :
+	   begin
+	      wait_for_trailer <= 1;
+	      if(wait_for_trailer)
+		dsp_state <= DSP_WRITE_TRAILER;
+	      new_trailer <= access_dat_i[31:0]; // Leave trailer unchanged
+	      odd <= is_odd;
+	      write_adr <= hdr_length_reg + data_in_lenx2 + HEADER_OFFSET;
+	   end
+
+	 DSP_WRITE_TRAILER :
+	   begin
+	      dsp_state <= DSP_READ;
+	      write_adr <= write_adr - 1;
+	      read_adr <= read_adr - 1;
+	      new_header[15:0] <= write_adr + (1 - HEADER_OFFSET); // length = addr of trailer + 1
+	   end
+
+	 DSP_READ :
+	   begin
+	      read_adr <= read_adr - 1;
+	      if(odd)
+		dsp_state <= DSP_READ_WAIT;
+	      else
+		dsp_state <= DSP_WRITE_1;
+	      odd <= 0;
+	   end
+
+	 DSP_READ_WAIT :
+	   dsp_state <= DSP_WRITE_0;
+	 
+	 DSP_WRITE_1 :
+	   begin
+	      write_adr <= write_adr - 1;
+	      if(write_adr == (hdr_length_reg+HEADER_OFFSET))
+		begin
+		   write_adr <= HEADER_OFFSET;
+		   dsp_state <= DSP_WRITE_HEADER;
+		end
+	      dsp_state <= DSP_WRITE_0;
+	   end
+
+	 DSP_WRITE_0 :
+	   begin
+	      write_adr <= write_adr - 1;
+	      if(write_adr == (hdr_length_reg+HEADER_OFFSET))
+		begin
+		   write_adr <= HEADER_OFFSET;
+		   dsp_state <= DSP_WRITE_HEADER;
+		end
+	      else
+		dsp_state <= DSP_READ;
+	   end
+
+	 DSP_WRITE_HEADER :
+	   dsp_state <= DSP_DONE;
+
+	 DSP_DONE :
+	   begin
+	      read_adr <= HEADER_OFFSET;
+	      write_adr <= HEADER_OFFSET;
+	      dsp_state <= DSP_IDLE;
+	   end
+       endcase // case (dsp_state)
+
+   assign access_skip_read = 0;
+   assign access_done = (dsp_state == DSP_DONE);
+
+   assign access_stb = 1;
+
+   assign access_we = (dsp_state == DSP_WRITE_HEADER) | 
+		      (dsp_state == DSP_WRITE_TRAILER) |
+		      (dsp_state == DSP_WRITE_0) |
+		      (dsp_state == DSP_WRITE_1);
+   
+   assign access_dat_o = (dsp_state == DSP_WRITE_HEADER) ? { 4'h0, new_header } :
+			 (dsp_state == DSP_WRITE_TRAILER) ? { 4'h2, new_trailer } :
+			 (dsp_state == DSP_WRITE_0) ? { 4'h0, i8_0, 8'd0, q8_0, 8'd0 } :
+			 (dsp_state == DSP_WRITE_1) ? { 4'h0, i8_1, 8'd0, q8_1, 8'd0 } :
+			 34'h0DEADBEEF;
+         
+   assign access_adr = access_we ? write_adr : read_adr;
+      
+endmodule // dspengine_16to8
diff --git a/fpga/usrp2/sdr_lib/dsp_core_tx.v b/fpga/usrp2/sdr_lib/duc_chain.v
index 4e0163e0a..bd3402a1f 100644
--- a/fpga/usrp2/sdr_lib/dsp_core_tx.v
+++ b/fpga/usrp2/sdr_lib/duc_chain.v
@@ -1,5 +1,5 @@
 //
-// Copyright 2011 Ettus Research LLC
+// Copyright 2011-2012 Ettus Research LLC
 //
 // This program is free software: you can redistribute it and/or modify
 // it under the terms of the GNU General Public License as published by
@@ -15,26 +15,35 @@
 // along with this program.  If not, see <http://www.gnu.org/licenses/>.
 //
 
+//! The USRP digital up-conversion chain
 
-module dsp_core_tx
-  #(parameter BASE=0)
-  (input clk, input rst,
+module duc_chain
+  #(
+    parameter BASE = 0,
+    parameter DSPNO = 0,
+    parameter WIDTH = 24
+  )
+  (input clk, input rst, input clr,
    input set_stb, input [7:0] set_addr, input [31:0] set_data,
+   input set_stb_user, input [7:0] set_addr_user, input [31:0] set_data_user,
 
-   output [23:0] tx_i, output [23:0] tx_q,
+   // To TX frontend
+   output [WIDTH-1:0] tx_fe_i,
+   output [WIDTH-1:0] tx_fe_q,
 
-   // To tx_control
+   // From TX control
    input [31:0] sample,
    input run,
    output strobe,
    output [31:0] debug
    );
 
-   wire [15:0] i, q, scale_i, scale_q;
+   wire duc_enb;
+   wire [17:0] scale_factor;
    wire [31:0] phase_inc;
    reg [31:0]  phase;
    wire [7:0]  interp_rate;
-   wire [3:0]  dacmux_a, dacmux_b;
+   wire [3:0]  tx_femux_a, tx_femux_b;
    wire        enable_hb1, enable_hb2;
    wire        rate_change;
    
@@ -42,9 +51,9 @@ module dsp_core_tx
      (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
       .in(set_data),.out(phase_inc),.changed());
 
-   setting_reg #(.my_addr(BASE+1)) sr_1
+   setting_reg #(.my_addr(BASE+1), .width(18)) sr_1
      (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out({scale_i,scale_q}),.changed());
+      .in(set_data),.out(scale_factor),.changed());
    
    setting_reg #(.my_addr(BASE+2), .width(10)) sr_2
      (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
@@ -57,13 +66,13 @@ module dsp_core_tx
    reg 	       strobe_hb2 = 1;
    
    cic_strober #(.WIDTH(8))
-     cic_strober(.clock(clk),.reset(rst),.enable(run & ~rate_change),.rate(interp_rate),
+     cic_strober(.clock(clk),.reset(rst),.enable(duc_enb & ~rate_change),.rate(interp_rate),
 		 .strobe_fast(1),.strobe_slow(strobe_cic_pre) );
    cic_strober #(.WIDTH(2))
-     hb2_strober(.clock(clk),.reset(rst),.enable(run & ~rate_change),.rate(enable_hb2 ? 2 : 1),
+     hb2_strober(.clock(clk),.reset(rst),.enable(duc_enb & ~rate_change),.rate(enable_hb2 ? 2 : 1),
 		 .strobe_fast(strobe_cic_pre),.strobe_slow(strobe_hb2_pre) );
    cic_strober #(.WIDTH(2))
-     hb1_strober(.clock(clk),.reset(rst),.enable(run & ~rate_change),.rate(enable_hb1 ? 2 : 1),
+     hb1_strober(.clock(clk),.reset(rst),.enable(duc_enb & ~rate_change),.rate(enable_hb1 ? 2 : 1),
 		 .strobe_fast(strobe_hb2_pre),.strobe_slow(strobe_hb1_pre) );
    
    always @(posedge clk) strobe_hb1 <= strobe_hb1_pre;
@@ -74,7 +83,7 @@ module dsp_core_tx
    always @(posedge clk)
      if(rst)
        phase <= 0;
-     else if(~run)
+     else if(~duc_enb)
        phase <= 0;
      else
        phase <= phase + phase_inc;
@@ -82,8 +91,8 @@ module dsp_core_tx
    wire        signed [17:0] da, db;
    wire        signed [35:0] prod_i, prod_q;
 
-   wire [17:0] bb_i = {sample[31:16],2'b0};
-   wire [17:0] bb_q = {sample[15:0],2'b0};
+   wire [15:0] bb_i;
+   wire [15:0] bb_q;
    wire [17:0] i_interp, q_interp;
 
    wire [17:0] hb1_i, hb1_q, hb2_i, hb2_q;
@@ -92,10 +101,10 @@ module dsp_core_tx
    // Note that max CIC rate is 128, which would give an overflow on cpo if enable_hb2 is true,
    //   but the default case inside hb_interp handles this
    
-   hb_interp #(.IWIDTH(18),.OWIDTH(18),.ACCWIDTH(24)) hb_interp_i
-     (.clk(clk),.rst(rst),.bypass(~enable_hb1),.cpo(cpo),.stb_in(strobe_hb1),.data_in(bb_i),.stb_out(strobe_hb2),.data_out(hb1_i));
-   hb_interp #(.IWIDTH(18),.OWIDTH(18),.ACCWIDTH(24)) hb_interp_q
-     (.clk(clk),.rst(rst),.bypass(~enable_hb1),.cpo(cpo),.stb_in(strobe_hb1),.data_in(bb_q),.stb_out(strobe_hb2),.data_out(hb1_q));
+   hb_interp #(.IWIDTH(18),.OWIDTH(18),.ACCWIDTH(WIDTH)) hb_interp_i
+     (.clk(clk),.rst(rst),.bypass(~enable_hb1),.cpo(cpo),.stb_in(strobe_hb1),.data_in({bb_i, 2'b0}),.stb_out(strobe_hb2),.data_out(hb1_i));
+   hb_interp #(.IWIDTH(18),.OWIDTH(18),.ACCWIDTH(WIDTH)) hb_interp_q
+     (.clk(clk),.rst(rst),.bypass(~enable_hb1),.cpo(cpo),.stb_in(strobe_hb1),.data_in({bb_q, 2'b0}),.stb_out(strobe_hb2),.data_out(hb1_q));
    
    small_hb_int #(.WIDTH(18)) small_hb_interp_i
      (.clk(clk),.rst(rst),.bypass(~enable_hb2),.stb_in(strobe_hb2),.data_in(hb1_i),
@@ -105,24 +114,22 @@ module dsp_core_tx
       .output_rate(interp_rate),.stb_out(strobe_cic),.data_out(hb2_q));
    
    cic_interp  #(.bw(18),.N(4),.log2_of_max_rate(7))
-     cic_interp_i(.clock(clk),.reset(rst),.enable(run & ~rate_change),.rate(interp_rate),
+     cic_interp_i(.clock(clk),.reset(rst),.enable(duc_enb & ~rate_change),.rate(interp_rate),
 		  .strobe_in(strobe_cic),.strobe_out(1),
 		  .signal_in(hb2_i),.signal_out(i_interp));
    
    cic_interp  #(.bw(18),.N(4),.log2_of_max_rate(7))
-     cic_interp_q(.clock(clk),.reset(rst),.enable(run & ~rate_change),.rate(interp_rate),
+     cic_interp_q(.clock(clk),.reset(rst),.enable(duc_enb & ~rate_change),.rate(interp_rate),
 		  .strobe_in(strobe_cic),.strobe_out(1),
 		  .signal_in(hb2_q),.signal_out(q_interp));
 
-   assign      strobe = strobe_hb1;
-
-   localparam  cwidth = 24;  // was 18
+   localparam  cwidth = WIDTH;  // was 18
    localparam  zwidth = 24;  // was 16
 
    wire [cwidth-1:0] da_c, db_c;
    
    cordic_z24 #(.bitwidth(cwidth))
-     cordic(.clock(clk), .reset(rst), .enable(run),
+     cordic(.clock(clk), .reset(rst), .enable(duc_enb),
 	    .xi({i_interp,{(cwidth-18){1'b0}}}),.yi({q_interp,{(cwidth-18){1'b0}}}),
 	    .zi(phase[31:32-zwidth]),
 	    .xo(da_c),.yo(db_c),.zo() );
@@ -130,7 +137,7 @@ module dsp_core_tx
    MULT18X18S MULT18X18S_inst 
      (.P(prod_i),    // 36-bit multiplier output
       .A(da_c[cwidth-1:cwidth-18]),    // 18-bit multiplier input
-      .B({{2{scale_i[15]}},scale_i}),    // 18-bit multiplier input
+      .B(scale_factor),    // 18-bit multiplier input
       .C(clk),    // Clock input
       .CE(1),  // Clock enable input
       .R(rst)     // Synchronous reset input
@@ -139,15 +146,20 @@ module dsp_core_tx
    MULT18X18S MULT18X18S_inst_2 
      (.P(prod_q),    // 36-bit multiplier output
       .A(db_c[cwidth-1:cwidth-18]),    // 18-bit multiplier input
-      .B({{2{scale_q[15]}},scale_q}),    // 18-bit multiplier input
+      .B(scale_factor),    // 18-bit multiplier input
       .C(clk),    // Clock input
       .CE(1),  // Clock enable input
       .R(rst)     // Synchronous reset input
       );
 
-   assign tx_i = prod_i[28:5];
-   assign tx_q = prod_q[28:5];
-   
+   dsp_tx_glue #(.DSPNO(DSPNO), .WIDTH(WIDTH)) dsp_tx_glue(
+    .clock(clk), .reset(rst), .clear(clr), .enable(run),
+    .set_stb(set_stb_user), .set_addr(set_addr_user), .set_data(set_data_user),
+    .frontend_i(tx_fe_i), .frontend_q(tx_fe_q),
+    .duc_out_i(prod_i[33:34-WIDTH]), .duc_out_q(prod_q[33:34-WIDTH]),
+    .duc_in_sample({bb_i, bb_q}), .duc_in_strobe(strobe_hb1), .duc_in_enable(duc_enb),
+    .bb_sample(sample), .bb_strobe(strobe));
+
    assign      debug = {strobe_cic, strobe_hb1, strobe_hb2,run};
 
 endmodule // dsp_core
diff --git a/fpga/usrp2/sdr_lib/dummy_rx.v b/fpga/usrp2/sdr_lib/dummy_rx.v
index b22d5f896..42bbe36b2 100644
--- a/fpga/usrp2/sdr_lib/dummy_rx.v
+++ b/fpga/usrp2/sdr_lib/dummy_rx.v
@@ -76,4 +76,4 @@ module dummy_rx
        q_out <= q_out + 1;
        
    
-endmodule // dsp_core_rx
+endmodule // ddc_chain
diff --git a/fpga/usrp2/timing/time_64bit.v b/fpga/usrp2/timing/time_64bit.v
index 03df07108..6f335890e 100644
--- a/fpga/usrp2/timing/time_64bit.v
+++ b/fpga/usrp2/timing/time_64bit.v
@@ -1,5 +1,5 @@
 //
-// Copyright 2011 Ettus Research LLC
+// Copyright 2011-2012 Ettus Research LLC
 //
 // This program is free software: you can redistribute it and/or modify
 // it under the terms of the GNU General Public License as published by
@@ -18,7 +18,7 @@
 
 
 module time_64bit
-  #(parameter TICKS_PER_SEC = 32'd100000000,
+  #(
     parameter BASE = 0)
    (input clk, input rst,
     input set_stb, input [7:0] set_addr, input [31:0] set_data,  
@@ -31,23 +31,20 @@ module time_64bit
     output [31:0] debug
     );
    
-   localparam 	   NEXT_SECS = 0;   
-   localparam 	   NEXT_TICKS = 1;
+   localparam 	   NEXT_TICKS_HI = 0;
+   localparam 	   NEXT_TICKS_LO = 1;
    localparam      PPS_POLSRC = 2;
    localparam      PPS_IMM = 3;
-   localparam      TPS = 4;
    localparam      MIMO_SYNC = 5;
    
-   reg [31:0] 	   seconds, ticks;
-   wire 	   end_of_second;
+   reg [63:0] 	   ticks;
 
    always @(posedge clk)
-     vita_time <= {seconds,ticks};
+     vita_time <= ticks;
    
    wire [63:0] 	   vita_time_rcvd;
    
-   wire [31:0] 	   next_ticks_preset, next_seconds_preset;
-   wire [31:0] 	   ticks_per_sec_reg;
+   wire [63:0] 	   next_ticks_preset;
    wire 	   set_on_pps_trig;
    reg 		   set_on_next_pps;
    wire 	   pps_polarity, pps_source, set_imm;
@@ -57,18 +54,18 @@ module time_64bit
 
    reg [15:0] 	   sync_counter;
    wire 	   sync_rcvd;
-   wire [31:0] 	   mimo_secs, mimo_ticks;
+   wire [63:0] 	   mimo_ticks;
    wire 	   mimo_sync_now;
    wire 	   mimo_sync;
    wire [7:0] 	   sync_delay;
    
-   setting_reg #(.my_addr(BASE+NEXT_TICKS)) sr_next_ticks
+   setting_reg #(.my_addr(BASE+NEXT_TICKS_LO)) sr_next_ticks_lo
      (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out(next_ticks_preset),.changed());
+      .in(set_data),.out(next_ticks_preset[31:0]),.changed());
    
-   setting_reg #(.my_addr(BASE+NEXT_SECS)) sr_next_secs
+   setting_reg #(.my_addr(BASE+NEXT_TICKS_HI)) sr_next_ticks_hi
      (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out(next_seconds_preset),.changed(set_on_pps_trig));
+      .in(set_data),.out(next_ticks_preset[63:32]),.changed(set_on_pps_trig));
 
    setting_reg #(.my_addr(BASE+PPS_POLSRC), .width(2)) sr_pps_polsrc
      (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
@@ -78,10 +75,6 @@ module time_64bit
      (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
       .in(set_data),.out(set_imm),.changed());
 
-   setting_reg #(.my_addr(BASE+TPS), .at_reset(TICKS_PER_SEC)) sr_tps
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out(ticks_per_sec_reg),.changed());
-
    setting_reg #(.my_addr(BASE+MIMO_SYNC), .at_reset(0), .width(9)) sr_mimosync
      (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
       .in(set_data),.out({mimo_sync,sync_delay}),.changed());
@@ -110,29 +103,21 @@ module time_64bit
      else if(set_imm | pps_edge)
        set_on_next_pps <= 0;
 
-   wire [31:0] 	   ticks_plus_one = ticks + 1;
+   wire [63:0] 	   ticks_plus_one = ticks + 1;
    
    always @(posedge clk)
      if(rst)
        begin
-	  seconds <= 32'd0;
-	  ticks <= 32'd0;
+	  ticks <= 64'd0;
        end
      else if((set_imm | pps_edge) & set_on_next_pps)
        begin
-	  seconds <= next_seconds_preset;
 	  ticks <= next_ticks_preset;
        end
      else if(mimo_sync_now)
        begin
-	  seconds <= mimo_secs;
 	  ticks <= mimo_ticks;
        end
-     else if(ticks_plus_one == ticks_per_sec_reg)
-       begin
-	  seconds <= seconds + 1;
-	  ticks <= 0;
-       end
      else
        ticks <= ticks_plus_one;
 
@@ -162,9 +147,8 @@ module time_64bit
       .sync_rcvd(sync_rcvd),
       .exp_time_in(exp_time_in) );
 
-   assign mimo_secs = vita_time_rcvd[63:32];
-   assign mimo_ticks = vita_time_rcvd[31:0] + {16'd0,sync_delay};
-   assign mimo_sync_now = mimo_sync & sync_rcvd & (mimo_ticks <= TICKS_PER_SEC);
+   assign mimo_ticks = vita_time_rcvd[63:0] + {48'd0,sync_delay};
+   assign mimo_sync_now = mimo_sync & sync_rcvd;
 
    assign debug = { { 24'b0} ,
 		    { 2'b0, exp_time_in, exp_time_out, mimo_sync, mimo_sync_now, sync_rcvd, send_sync} };
diff --git a/fpga/usrp2/timing/time_compare.v b/fpga/usrp2/timing/time_compare.v
index 54ea000d6..21607f51c 100644
--- a/fpga/usrp2/timing/time_compare.v
+++ b/fpga/usrp2/timing/time_compare.v
@@ -1,5 +1,5 @@
 //
-// Copyright 2011 Ettus Research LLC
+// Copyright 2011-2012 Ettus Research LLC
 //
 // This program is free software: you can redistribute it and/or modify
 // it under the terms of the GNU General Public License as published by
@@ -16,49 +16,19 @@
 //
 
 
-// Top 32 bits are integer seconds, bottom 32 are clock ticks within a second
+// 64 bits worth of ticks
 
 module time_compare
   (input [63:0] time_now,
    input [63:0] trigger_time,
    output now,
    output early,
-   output late, 
+   output late,
    output too_early);
-   
-   wire    sec_match   = (time_now[63:32] == trigger_time[63:32]);
-   wire    sec_late    = (time_now[63:32] > trigger_time[63:32]);
 
-   wire    tick_match  = (time_now[31:0] == trigger_time[31:0]);
-   wire    tick_late   = (time_now[31:0] > trigger_time[31:0]);
-/*   
-   assign now 	       = sec_match & tick_match;
-   assign late 	       = sec_late | (sec_match & tick_late);
-   assign early        = ~now & ~late;
-*/
+    assign now = time_now == trigger_time;
+    assign late = time_now > trigger_time;
+    assign early = ~now & ~late;
+    assign too_early = 0; //not implemented
 
-   /*
-   assign now = (time_now == trigger_time);
-   assign late = (time_now > trigger_time);
-   assign early = (time_now < trigger_time);
-   */
-
-   // Compare fewer bits instead of 64 to speed up logic
-   // Unused bits are not significant
-   //     Top bit of seconds would put us in year 2038, long after
-   //        the warranty has run out :)
-   //     Top 5 bits of ticks are always zero for clocks less than 134MHz
-   //     "late" can drop bottom few bits of ticks, and just delay signaling
-   //        of late.  
-   //     "now" cannot drop those bits, it needs to be exact.
-   
-   wire [57:0] short_now = {time_now[62:32],time_now[26:0]};
-   wire [57:0] short_trig = {trigger_time[62:32],trigger_time[26:0]};
-
-   assign now = (short_now == short_trig);
-   assign late = (short_now[57:5] > short_trig[57:5]);
-   assign early = (short_now < short_trig);
-   
-   assign too_early    = (trigger_time[63:32] > (time_now[63:32] + 4));  // Don't wait too long
-   
 endmodule // time_compare
diff --git a/fpga/usrp2/top/B100/B100.ucf b/fpga/usrp2/top/B100/B100.ucf
index 69fd49971..1c04c5d8d 100644
--- a/fpga/usrp2/top/B100/B100.ucf
+++ b/fpga/usrp2/top/B100/B100.ucf
@@ -25,6 +25,9 @@ NET "reset_n"  LOC = "D5"  ;
 NET "PPS_IN"  LOC = "M14"  ;
 NET "reset_codec"  LOC = "B14"  ;
 
+## recycles fpga_cfg_cclk for reset from fw
+NET "ext_reset"  LOC = "R14"  ;
+
 ## GPIF
 NET "GPIF_D<15>"  LOC = "P7"  ;
 NET "GPIF_D<14>"  LOC = "N8"  ;
@@ -43,17 +46,18 @@ NET "GPIF_D<2>"  LOC = "N9"  ;
 NET "GPIF_D<1>"  LOC = "P9"  ;
 NET "GPIF_D<0>"  LOC = "P8"  ;
 
-NET "GPIF_CTL<3>"  LOC = "N5"  ;
+##NET "GPIF_CTL<3>"  LOC = "N5"  ;
+NET "GPIF_CTL<3>"  LOC = "P12"  ;
 NET "GPIF_CTL<2>"  LOC = "M11"  ;
 NET "GPIF_CTL<1>"  LOC = "M9"  ;
 NET "GPIF_CTL<0>"  LOC = "M7"  ;
 
-NET "GPIF_RDY<3>"  LOC = "N11"  ;
-NET "GPIF_RDY<2>"  LOC = "T10"  ;
-NET "GPIF_RDY<1>"  LOC = "T4"  ;
-NET "GPIF_RDY<0>"  LOC = "R5"  ;
+##NET "GPIF_RDY<3>"  LOC = "N11"  ;
+##NET "GPIF_RDY<2>"  LOC = "T10"  ;
+NET "GPIF_SLWR"  LOC = "T4"  ;
+NET "GPIF_SLRD"  LOC = "R5"  ;
 
-NET "GPIF_CS"  LOC = "P12"  ;
+##NET "GPIF_CS"  LOC = "P12"  ;
 NET "GPIF_SLOE"  LOC = "R11"  ;
 NET "GPIF_PKTEND"  LOC = "P10"  ;
 NET "GPIF_ADR<0>"  LOC = "T11"  ;
diff --git a/fpga/usrp2/top/B100/B100.v b/fpga/usrp2/top/B100/B100.v
index f2d75c54e..dcda974b4 100644
--- a/fpga/usrp2/top/B100/B100.v
+++ b/fpga/usrp2/top/B100/B100.v
@@ -23,8 +23,8 @@ module B100
    output [2:0] debug_led, output [31:0] debug, output [1:0] debug_clk,
 
    // GPIF
-   inout [15:0] GPIF_D, input [3:0] GPIF_CTL, output [3:0] GPIF_RDY,
-   input [1:0] GPIF_ADR, output GPIF_CS, output GPIF_SLOE, output GPIF_PKTEND,
+   inout [15:0] GPIF_D, input [3:0] GPIF_CTL, output GPIF_SLOE, 
+   output [1:0] GPIF_ADR, output GPIF_SLWR, output GPIF_SLRD, output GPIF_PKTEND,
    input IFCLK,
    
    inout SDA_FPGA, inout SCL_FPGA, // I2C
@@ -41,7 +41,8 @@ module B100
    input [11:0] adc, input RXSYNC,
   
    input PPS_IN,
-   input reset_n, output reset_codec
+   input reset_n, output reset_codec,
+   input ext_reset
    );
 
    assign reset_codec = 1;  // Believed to be active low
@@ -55,7 +56,7 @@ module B100
 
    BUFG clk_fpga_BUFG (.I(clk_fpga_in), .O(clk_fpga));
    
-   reset_sync reset_sync(.clk(clk_fpga), .reset_in(~reset_n), .reset_out(reset));
+   reset_sync reset_sync(.clk(clk_fpga), .reset_in((~reset_n) | (~ext_reset)), .reset_out(reset));
    
    // /////////////////////////////////////////////////////////////////////////
    // SPI
@@ -156,9 +157,10 @@ module B100
    u1plus_core u1p_c(.clk_fpga(clk_fpga), .rst_fpga(reset),
 		     .debug_led(debug_led), .debug(debug), .debug_clk(debug_clk),
 		     .debug_txd(), .debug_rxd(1'b1),
-		     .gpif_d(GPIF_D), .gpif_ctl(GPIF_CTL), .gpif_rdy(GPIF_RDY),
-		     .gpif_misc({GPIF_CS,GPIF_SLOE,GPIF_PKTEND}),
-		     .gpif_clk(IFCLK),
+		     
+		     .gpif_d(GPIF_D), .gpif_ctl(GPIF_CTL), .gpif_pktend(GPIF_PKTEND),
+		     .gpif_sloe(GPIF_SLOE), .gpif_slwr(GPIF_SLWR), .gpif_slrd(GPIF_SLRD),
+		     .gpif_fifoadr(GPIF_ADR), .gpif_clk(IFCLK),
 
 		     .db_sda(SDA_FPGA), .db_scl(SCL_FPGA),
 		     .sclk(sclk), .sen({SEN_CODEC,SEN_TX_DB,SEN_RX_DB}), .mosi(mosi), .miso(miso),
diff --git a/fpga/usrp2/top/B100/Makefile.B100 b/fpga/usrp2/top/B100/Makefile.B100
index 90dd25942..3cdbb62c0 100644
--- a/fpga/usrp2/top/B100/Makefile.B100
+++ b/fpga/usrp2/top/B100/Makefile.B100
@@ -1,5 +1,5 @@
 #
-# Copyright 2008 Ettus Research LLC
+# Copyright 2008-2012 Ettus Research LLC
 #
 
 ##################################################
@@ -7,7 +7,14 @@
 ##################################################
 TOP_MODULE := B100
 BUILD_DIR := build-B100/
-export PROJ_FILE := $(BUILD_DIR)$(TOP_MODULE).ise
+
+# set me in a custom makefile
+CUSTOM_SRCS =
+CUSTOM_DEFS =
+
+##################################################
+# Include other makefiles
+##################################################
 
 include ../Makefile.common
 include ../../fifo/Makefile.srcs
@@ -50,7 +57,7 @@ SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \
 $(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \
 $(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \
 $(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS) \
-$(GPIF_SRCS)
+$(GPIF_SRCS) $(CUSTOM_SRCS)
 
 ##################################################
 # Process Properties
@@ -63,7 +70,8 @@ SYNTHESIZE_PROPERTIES = \
 "Register Balancing" Yes \
 "Use Clock Enable" Auto \
 "Use Synchronous Reset" Auto \
-"Use Synchronous Set" Auto
+"Use Synchronous Set" Auto \
+"Verilog Macros" "$(CUSTOM_MOD_DEFS)"
 
 TRANSLATE_PROPERTIES = \
 "Macro Search Path" "$(shell pwd)/../../coregen/"
diff --git a/fpga/usrp2/top/B100/core_compile b/fpga/usrp2/top/B100/core_compile
index b2ccc8b49..b62cbaee0 100755
--- a/fpga/usrp2/top/B100/core_compile
+++ b/fpga/usrp2/top/B100/core_compile
@@ -1 +1 @@
-iverilog -Wall -y. -y ../../control_lib/ -y ../../fifo/ -y ../../gpif/ -y ../../models/ -y ../../sdr_lib/ -y ../../coregen/ -y ../../vrt/ -y ../../opencores/i2c/rtl/verilog/ -y ../../opencores/spi/rtl/verilog/ -y ../../timing/ -y ../../opencores/8b10b/ -I ../../opencores/spi/rtl/verilog/ -I ../../opencores/i2c/rtl/verilog/ -y ../../simple_gemac u1plus_core.v  2>&1   | grep -v timescale | grep -v coregen | grep -v models
+iverilog -Wall -y. -y ../../control_lib/ -y ../../custom/ -y ../../fifo/ -y ../../gpif/ -y ../../models/ -y ../../sdr_lib/ -y ../../coregen/ -y ../../vrt/ -y ../../opencores/i2c/rtl/verilog/ -y ../../opencores/spi/rtl/verilog/ -y ../../timing/ -y ../../opencores/8b10b/ -I ../../opencores/spi/rtl/verilog/ -I ../../opencores/i2c/rtl/verilog/ -y ../../simple_gemac u1plus_core.v  2>&1   | grep -v timescale | grep -v coregen | grep -v models
diff --git a/fpga/usrp2/top/B100/timing.ucf b/fpga/usrp2/top/B100/timing.ucf
index b2a455f6d..96c47cf2c 100644
--- a/fpga/usrp2/top/B100/timing.ucf
+++ b/fpga/usrp2/top/B100/timing.ucf
@@ -3,3 +3,12 @@ TIMESPEC "TS_CLK_FPGA_P" = PERIOD "CLK_FPGA_P" 15625 ps HIGH 50 %;
 
 NET "IFCLK" TNM_NET = "IFCLK";
 TIMESPEC "TS_IFCLK" = PERIOD "IFCLK" 20833 ps HIGH 50 %;
+
+#constrain FX2 IO
+NET "GPIF_D<*>" MAXDELAY = 5.5 ns;
+NET "GPIF_CTL<*>" MAXDELAY = 5.5 ns;
+NET "GPIF_ADR<*>" MAXDELAY = 5.5ns;
+NET "GPIF_SLWR" MAXDELAY = 5.5 ns;
+NET "GPIF_SLRD" MAXDELAY = 5.5 ns;
+NET "GPIF_SLOE" MAXDELAY = 5.5 ns;
+NET "GPIF_PKTEND" MAXDELAY = 5.5 ns;
diff --git a/fpga/usrp2/top/B100/u1plus_core.v b/fpga/usrp2/top/B100/u1plus_core.v
index c883c5ca8..e335fb8bb 100644
--- a/fpga/usrp2/top/B100/u1plus_core.v
+++ b/fpga/usrp2/top/B100/u1plus_core.v
@@ -1,5 +1,5 @@
 //
-// Copyright 2011 Ettus Research LLC
+// Copyright 2011-2012 Ettus Research LLC
 //
 // This program is free software: you can redistribute it and/or modify
 // it under the terms of the GNU General Public License as published by
@@ -23,8 +23,9 @@ module u1plus_core
    output debug_txd, input debug_rxd,
    
    // GPIF
-   inout [15:0] gpif_d, input [3:0] gpif_ctl, output [3:0] gpif_rdy,
-   output [2:0] gpif_misc, input gpif_clk,
+   inout [15:0] gpif_d, input [3:0] gpif_ctl, output gpif_sloe,
+   output gpif_slwr, output gpif_slrd, output gpif_pktend, output [1:0] gpif_fifoadr,
+   input gpif_clk,
    
    inout db_sda, inout db_scl,
    output sclk, output [15:0] sen, output mosi, input miso,
@@ -37,7 +38,7 @@ module u1plus_core
    );
 
    localparam TXFIFOSIZE = 11;
-   localparam RXFIFOSIZE = 11;
+   localparam RXFIFOSIZE = 12;
 
    // 64 total regs in address space
    localparam SR_RX_CTRL0 = 0;       // 9 regs (+0 to +8)
@@ -52,9 +53,9 @@ module u1plus_core
    localparam SR_TX_FRONT = 54;      // 5 regs (+0 to +4)
 
    localparam SR_REG_TEST32 = 60;    // 1 reg
-   localparam SR_CLEAR_RX_FIFO = 61; // 1 reg
-   localparam SR_CLEAR_TX_FIFO = 62; // 1 reg
+   localparam SR_CLEAR_FIFO = 61;    // 1 reg
    localparam SR_GLOBAL_RESET = 63;  // 1 reg
+   localparam SR_USER_REGS = 64;     // 2 regs
 
    localparam SR_GPIO = 128;         // 5 regs
    
@@ -64,11 +65,11 @@ module u1plus_core
    wire 	pps_int;
    wire [63:0] 	vita_time, vita_time_pps;
    reg [15:0] 	reg_cgen_ctrl, reg_test;
-   
-   wire [7:0] 	set_addr;
-   wire [31:0] 	set_data;
-   wire 	set_stb;
-   
+
+   wire [7:0]  set_addr, set_addr_user;
+   wire [31:0] set_data, set_data_user;
+   wire        set_stb, set_stb_user;
+
    wire [31:0]  debug0;
    wire [31:0]  debug1;
 
@@ -105,68 +106,70 @@ module u1plus_core
    wire 	 tx_src_rdy, tx_dst_rdy, rx_src_rdy, rx_dst_rdy, 
 		 tx_err_src_rdy, tx_err_dst_rdy;
 
-   wire 	 clear_tx, clear_rx;
-   
-   setting_reg #(.my_addr(SR_CLEAR_RX_FIFO), .width(1)) sr_clear_rx
-     (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out(),.changed(clear_rx));
+   wire 	 clear_fifo;
 
-   setting_reg #(.my_addr(SR_CLEAR_TX_FIFO), .width(1)) sr_clear_tx
+   setting_reg #(.my_addr(SR_CLEAR_FIFO), .width(1)) sr_clear_fifo
      (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out(),.changed(clear_tx));
+      .in(set_data),.out(),.changed(clear_fifo));
 
-   gpif #(.TXFIFOSIZE(TXFIFOSIZE), .RXFIFOSIZE(RXFIFOSIZE))
-   gpif (.gpif_clk(gpif_clk), .gpif_rst(gpif_rst), .gpif_d(gpif_d),
-	 .gpif_ctl(gpif_ctl), .gpif_rdy(gpif_rdy), .gpif_misc(gpif_misc),
+   wire 	 run_rx0, run_rx1;
+
+   slave_fifo #(.TXFIFOSIZE(TXFIFOSIZE), .RXFIFOSIZE(RXFIFOSIZE))
+   slave_fifo (.gpif_clk(gpif_clk), .gpif_rst(gpif_rst), .gpif_d(gpif_d),
+	 .gpif_ctl(gpif_ctl), .sloe(gpif_sloe), .slwr(gpif_slwr), .slrd(gpif_slrd),
+     .pktend(gpif_pktend), .fifoadr(gpif_fifoadr),
 	 
 	 .wb_clk(wb_clk), .wb_rst(wb_rst),
 	 .wb_adr_o(m0_adr), .wb_dat_mosi(m0_dat_mosi), .wb_dat_miso(m0_dat_miso),
 	 .wb_sel_o(m0_sel), .wb_cyc_o(m0_cyc), .wb_stb_o(m0_stb), .wb_we_o(m0_we),
 	 .wb_ack_i(m0_ack), .triggers(8'd0),
 	 
-	 .fifo_clk(wb_clk), .fifo_rst(wb_rst), .clear_tx(clear_tx), .clear_rx(clear_rx),
+	 .dsp_rx_run(run_rx0 | run_rx1),
+	 
+	 .fifo_clk(wb_clk), .fifo_rst(wb_rst), .clear_tx(clear_fifo), .clear_rx(clear_fifo),
 	 .tx_data_o(tx_data), .tx_src_rdy_o(tx_src_rdy), .tx_dst_rdy_i(tx_dst_rdy),
 	 .rx_data_i(rx_data), .rx_src_rdy_i(rx_src_rdy), .rx_dst_rdy_o(rx_dst_rdy),
 	 .tx_err_data_i(tx_err_data), .tx_err_src_rdy_i(tx_err_src_rdy), .tx_err_dst_rdy_o(tx_err_dst_rdy),
 	 
 	 .tx_underrun(tx_underrun_gpif), .rx_overrun(rx_overrun_gpif),
 
-	 .frames_per_packet(frames_per_packet),
+	 .test_len(0), .test_rate(0), .test_ctrl(0),
 	 .debug0(debug0), .debug1(debug1));
 
    // /////////////////////////////////////////////////////////////////////////
    // RX ADC Frontend, does IQ Balance, DC Offset, muxing
 
-   wire [23:0] 	 adc_i, adc_q;  // 24 bits is total overkill here, but it matches u2/u2p
-   wire 	 run_rx0, run_rx1;
-   
+   wire [23:0] 	 rx_fe_i, rx_fe_q;  // 24 bits is total overkill here, but it matches u2/u2p
+
    rx_frontend #(.BASE(SR_RX_FRONT)) rx_frontend
      (.clk(wb_clk),.rst(wb_rst),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
       .adc_a({rx_i,4'b00}),.adc_ovf_a(0),
       .adc_b({rx_q,4'b00}),.adc_ovf_b(0),
-      .i_out(adc_i), .q_out(adc_q), .run(run_rx0 | run_rx1), .debug());
+      .i_out(rx_fe_i), .q_out(rx_fe_q), .run(run_rx0 | run_rx1), .debug());
    
    // /////////////////////////////////////////////////////////////////////////
    // DSP RX 0
 
    wire [31:0] 	 sample_rx0;
-   wire 	 strobe_rx0;
+   wire 	 strobe_rx0, clear_rx0;
    wire [35:0] 	 vita_rx_data0;
    wire 	 vita_rx_src_rdy0, vita_rx_dst_rdy0;
    
-   dsp_core_rx #(.BASE(SR_RX_DSP0)) dsp_core_rx0
-     (.clk(wb_clk),.rst(wb_rst),
+   ddc_chain #(.BASE(SR_RX_DSP0), .DSPNO(0)) ddc_chain0
+     (.clk(wb_clk), .rst(wb_rst), .clr(clear_rx0),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
-      .adc_i(adc_i),.adc_ovf_i(0),.adc_q(adc_q),.adc_ovf_q(0),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
+      .rx_fe_i(rx_fe_i),.rx_fe_q(rx_fe_q),
       .sample(sample_rx0), .run(run_rx0), .strobe(strobe_rx0),
       .debug() );
 
-   vita_rx_chain #(.BASE(SR_RX_CTRL0), .UNIT(0), .FIFOSIZE(10), .PROT_ENG_FLAGS(0)) vita_rx_chain0
-     (.clk(wb_clk),.reset(wb_rst),.clear(clear_rx),
+   vita_rx_chain #(.BASE(SR_RX_CTRL0), .UNIT(0), .FIFOSIZE(10), .PROT_ENG_FLAGS(0), .DSP_NUMBER(0)) vita_rx_chain0
+     (.clk(wb_clk),.reset(wb_rst),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
       .vita_time(vita_time), .overrun(rx_overrun_dsp0),
-      .sample(sample_rx0), .run(run_rx0), .strobe(strobe_rx0),
+      .sample(sample_rx0), .run(run_rx0), .strobe(strobe_rx0), .clear_o(clear_rx0),
       .rx_data_o(vita_rx_data0), .rx_dst_rdy_i(vita_rx_dst_rdy0), .rx_src_rdy_o(vita_rx_src_rdy0),
       .debug() );
    
@@ -174,22 +177,24 @@ module u1plus_core
    // DSP RX 1
 
    wire [31:0] 	 sample_rx1;
-   wire 	 strobe_rx1;
+   wire 	 strobe_rx1, clear_rx1;
    wire [35:0] 	 vita_rx_data1;
    wire 	 vita_rx_src_rdy1, vita_rx_dst_rdy1;
    
-   dsp_core_rx #(.BASE(SR_RX_DSP1)) dsp_core_rx1
-     (.clk(wb_clk),.rst(wb_rst),
+   ddc_chain #(.BASE(SR_RX_DSP1), .DSPNO(1)) ddc_chain1
+     (.clk(wb_clk),.rst(wb_rst), .clr(clear_rx1),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
-      .adc_i(adc_i),.adc_ovf_i(0),.adc_q(adc_q),.adc_ovf_q(0),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
+      .rx_fe_i(rx_fe_i),.rx_fe_q(rx_fe_q),
       .sample(sample_rx1), .run(run_rx1), .strobe(strobe_rx1),
       .debug() );
 
-   vita_rx_chain #(.BASE(SR_RX_CTRL1), .UNIT(1), .FIFOSIZE(10), .PROT_ENG_FLAGS(0)) vita_rx_chain1
-     (.clk(wb_clk),.reset(wb_rst),.clear(clear_rx),
+   vita_rx_chain #(.BASE(SR_RX_CTRL1), .UNIT(1), .FIFOSIZE(10), .PROT_ENG_FLAGS(0), .DSP_NUMBER(1)) vita_rx_chain1
+     (.clk(wb_clk),.reset(wb_rst),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
       .vita_time(vita_time), .overrun(rx_overrun_dsp1),
-      .sample(sample_rx1), .run(run_rx1), .strobe(strobe_rx1),
+      .sample(sample_rx1), .run(run_rx1), .strobe(strobe_rx1), .clear_o(clear_rx1),
       .rx_data_o(vita_rx_data1), .rx_dst_rdy_i(vita_rx_dst_rdy1), .rx_src_rdy_o(vita_rx_src_rdy1),
       .debug() );
 
@@ -197,7 +202,7 @@ module u1plus_core
    // RX Stream muxing
 
    fifo36_mux #(.prio(0)) mux_data_streams
-     (.clk(wb_clk), .reset(wb_rst), .clear(0),
+     (.clk(wb_clk), .reset(wb_rst), .clear(clear_fifo),
       .data0_i(vita_rx_data0), .src0_rdy_i(vita_rx_src_rdy0), .dst0_rdy_o(vita_rx_dst_rdy0),
       .data1_i(vita_rx_data1), .src1_rdy_i(vita_rx_src_rdy1), .dst1_rdy_o(vita_rx_dst_rdy1),
       .data_o(rx_data), .src_rdy_o(rx_src_rdy), .dst_rdy_i(rx_dst_rdy));
@@ -205,27 +210,38 @@ module u1plus_core
    // ///////////////////////////////////////////////////////////////////////////////////
    // DSP TX
 
-   wire [23:0] 	 tx_i_int, tx_q_int;
    wire 	 run_tx;
-   
-   vita_tx_chain #(.BASE_CTRL(SR_TX_CTRL), .BASE_DSP(SR_TX_DSP), 
+   wire [23:0] 	 tx_fe_i, tx_fe_q;
+   wire [31:0]   sample_tx;
+   wire strobe_tx, clear_tx;
+
+   vita_tx_chain #(.BASE(SR_TX_CTRL), .FIFOSIZE(10), .POST_ENGINE_FIFOSIZE(11),
 		   .REPORT_ERROR(1), .DO_FLOW_CONTROL(0),
 		   .PROT_ENG_FLAGS(0), .USE_TRANS_HEADER(0),
 		   .DSP_NUMBER(0)) 
    vita_tx_chain
      (.clk(wb_clk), .reset(wb_rst),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
       .vita_time(vita_time),
       .tx_data_i(tx_data), .tx_src_rdy_i(tx_src_rdy), .tx_dst_rdy_o(tx_dst_rdy),
       .err_data_o(tx_err_data), .err_src_rdy_o(tx_err_src_rdy), .err_dst_rdy_i(tx_err_dst_rdy),
-      .tx_i(tx_i_int),.tx_q(tx_q_int),
-      .underrun(tx_underrun_dsp), .run(run_tx),
+      .sample(sample_tx), .strobe(strobe_tx),
+      .underrun(tx_underrun_dsp), .run(run_tx), .clear_o(clear_tx),
       .debug(debug_vt));
 
+   duc_chain #(.BASE(SR_TX_DSP), .DSPNO(0)) duc_chain
+     (.clk(wb_clk), .rst(wb_rst), .clr(clear_tx),
+      .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
+      .tx_fe_i(tx_fe_i),.tx_fe_q(tx_fe_q),
+      .sample(sample_tx), .run(run_tx), .strobe(strobe_tx),
+      .debug() );
+
    tx_frontend #(.BASE(SR_TX_FRONT), .WIDTH_OUT(14)) tx_frontend
      (.clk(wb_clk), .rst(wb_rst),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
-      .tx_i(tx_i_int), .tx_q(tx_q_int), .run(1'b1),
+      .tx_i(tx_fe_i), .tx_q(tx_fe_q), .run(1'b1),
       .dac_a(tx_i), .dac_b(tx_q));
 
    // /////////////////////////////////////////////////////////////////////////////////////
@@ -387,11 +403,17 @@ module u1plus_core
       .wb_stb_i(s8_stb),.wb_we_i(s8_we),.wb_ack_o(s8_ack),
       .strobe(set_stb),.addr(set_addr),.data(set_data) );
 
+   user_settings #(.BASE(SR_USER_REGS)) user_settings
+     (.clk(wb_clk),.rst(wb_rst),.set_stb(set_stb),
+      .set_addr(set_addr),.set_data(set_data),
+      .set_addr_user(set_addr_user),.set_data_user(set_data_user),
+      .set_stb_user(set_stb_user) );
+
    // /////////////////////////////////////////////////////////////////////////
    // Readback mux 32 -- Slave #7
 
    //compatibility number -> increment when the fpga has been sufficiently altered
-   localparam compat_num = {16'd8, 16'd1}; //major, minor
+   localparam compat_num = {16'd9, 16'd0}; //major, minor
 
    wire [31:0] reg_test32;
 
@@ -416,7 +438,7 @@ module u1plus_core
    // /////////////////////////////////////////////////////////////////////////
    // VITA Timing
 
-   time_64bit #(.TICKS_PER_SEC(32'd64000000),.BASE(SR_TIME64)) time_64bit
+   time_64bit #(.BASE(SR_TIME64)) time_64bit
      (.clk(wb_clk), .rst(wb_rst), .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
       .pps(pps_in), .vita_time(vita_time), .vita_time_pps(vita_time_pps), .pps_int(pps_int),
       .exp_time_in(0));
diff --git a/fpga/usrp2/top/E1x0/Makefile.E100 b/fpga/usrp2/top/E1x0/Makefile.E100
index 9b9a48911..ad5a0c1bd 100644
--- a/fpga/usrp2/top/E1x0/Makefile.E100
+++ b/fpga/usrp2/top/E1x0/Makefile.E100
@@ -1,5 +1,5 @@
 #
-# Copyright 2008 Ettus Research LLC
+# Copyright 2008-2012 Ettus Research LLC
 #
 
 ##################################################
@@ -8,6 +8,10 @@
 TOP_MODULE = u1e
 BUILD_DIR = $(abspath build$(ISE)-E100)
 
+# set me in a custom makefile
+CUSTOM_SRCS =
+CUSTOM_DEFS =
+
 ##################################################
 # Include other makefiles
 ##################################################
@@ -53,7 +57,7 @@ SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \
 $(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \
 $(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \
 $(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS) \
-$(GPMC_SRCS)
+$(GPMC_SRCS) $(CUSTOM_SRCS)
 
 ##################################################
 # Process Properties
@@ -66,7 +70,8 @@ SYNTHESIZE_PROPERTIES = \
 "Register Balancing" Yes \
 "Use Clock Enable" Auto \
 "Use Synchronous Reset" Auto \
-"Use Synchronous Set" Auto
+"Use Synchronous Set" Auto \
+"Verilog Macros" "$(CUSTOM_MOD_DEFS)"
 
 TRANSLATE_PROPERTIES = \
 "Macro Search Path" "$(shell pwd)/../../coregen/"
diff --git a/fpga/usrp2/top/E1x0/Makefile.E110 b/fpga/usrp2/top/E1x0/Makefile.E110
index be2761baf..291ac0a44 100644
--- a/fpga/usrp2/top/E1x0/Makefile.E110
+++ b/fpga/usrp2/top/E1x0/Makefile.E110
@@ -1,5 +1,5 @@
 #
-# Copyright 2008 Ettus Research LLC
+# Copyright 2008-2012 Ettus Research LLC
 #
 
 ##################################################
@@ -8,6 +8,10 @@
 TOP_MODULE = u1e
 BUILD_DIR = $(abspath build$(ISE)-E110)
 
+# set me in a custom makefile
+CUSTOM_SRCS =
+CUSTOM_DEFS =
+
 ##################################################
 # Include other makefiles
 ##################################################
@@ -53,7 +57,7 @@ SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \
 $(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \
 $(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \
 $(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS) \
-$(GPMC_SRCS)
+$(GPMC_SRCS) $(CUSTOM_SRCS)
 
 ##################################################
 # Process Properties
@@ -66,7 +70,8 @@ SYNTHESIZE_PROPERTIES = \
 "Register Balancing" Yes \
 "Use Clock Enable" Auto \
 "Use Synchronous Reset" Auto \
-"Use Synchronous Set" Auto
+"Use Synchronous Set" Auto \
+"Verilog Macros" "$(CUSTOM_MOD_DEFS)"
 
 TRANSLATE_PROPERTIES = \
 "Macro Search Path" "$(shell pwd)/../../coregen/"
diff --git a/fpga/usrp2/top/E1x0/core_compile b/fpga/usrp2/top/E1x0/core_compile
index 02d7f006e..14e138fa3 100755
--- a/fpga/usrp2/top/E1x0/core_compile
+++ b/fpga/usrp2/top/E1x0/core_compile
@@ -1,3 +1,3 @@
-iverilog -Wall -y. -y ../../control_lib/ -y ../../fifo/ -y ../../gpmc/ -y ../../models/ -y ../../sdr_lib/ -y ../../coregen/ -y ../../vrt/ -y ../../opencores/i2c/rtl/verilog/ -y ../../opencores/spi/rtl/verilog/ -y ../../timing/ -y ../../opencores/8b10b/ -I ../../opencores/spi/rtl/verilog/ -I ../../opencores/i2c/rtl/verilog/ -y ../../simple_gemac -y $XILINX/verilog/src/unisims u1e_core.v  2>&1  | grep -v timescale | grep -v coregen | grep -v models
+iverilog -Wall -y. -y ../../control_lib/ -y ../../custom/ -y ../../fifo/ -y ../../gpmc/ -y ../../models/ -y ../../sdr_lib/ -y ../../coregen/ -y ../../vrt/ -y ../../opencores/i2c/rtl/verilog/ -y ../../opencores/spi/rtl/verilog/ -y ../../timing/ -y ../../opencores/8b10b/ -I ../../opencores/spi/rtl/verilog/ -I ../../opencores/i2c/rtl/verilog/ -y ../../simple_gemac -y $XILINX/verilog/src/unisims u1e_core.v  2>&1  | grep -v timescale | grep -v coregen | grep -v models
 
 
diff --git a/fpga/usrp2/top/E1x0/u1e_core.v b/fpga/usrp2/top/E1x0/u1e_core.v
index aede63bac..ee27af939 100644
--- a/fpga/usrp2/top/E1x0/u1e_core.v
+++ b/fpga/usrp2/top/E1x0/u1e_core.v
@@ -1,5 +1,5 @@
 //
-// Copyright 2011 Ettus Research LLC
+// Copyright 2011-2012 Ettus Research LLC
 //
 // This program is free software: you can redistribute it and/or modify
 // it under the terms of the GNU General Public License as published by
@@ -56,9 +56,9 @@ module u1e_core
    localparam SR_TX_FRONT = 54;      // 5 regs (+0 to +4)
 
    localparam SR_REG_TEST32 = 60;    // 1 reg
-   localparam SR_CLEAR_RX_FIFO = 61; // 1 reg
-   localparam SR_CLEAR_TX_FIFO = 62; // 1 reg
+   localparam SR_CLEAR_FIFO = 61;    // 1 reg
    localparam SR_GLOBAL_RESET = 63;  // 1 reg
+   localparam SR_USER_REGS = 64;     // 2 regs
 
    localparam SR_GPIO = 128;         // 5 regs
    
@@ -70,10 +70,10 @@ module u1e_core
    reg [15:0] 	reg_cgen_ctrl, reg_test, xfer_rate;
    wire [7:0] 	test_rate;
    wire [3:0] 	test_ctrl;
-   
-   wire [7:0] 	set_addr;
-   wire [31:0] 	set_data;
-   wire 	set_stb;
+
+   wire [7:0]  set_addr, set_addr_user;
+   wire [31:0] set_data, set_data_user;
+   wire        set_stb, set_stb_user;
 
    wire [31:0] 	debug_vt;
    wire 	rx_overrun_dsp0, rx_overrun_dsp1, rx_overrun_gpmc, tx_underrun_dsp, tx_underrun_gpmc;
@@ -103,15 +103,13 @@ module u1e_core
    wire 	 tx_src_rdy, tx_dst_rdy, rx_src_rdy, rx_dst_rdy, 
 		 tx_err_src_rdy, tx_err_dst_rdy;
 
-   wire 	 clear_tx, clear_rx;
-   
-   setting_reg #(.my_addr(SR_CLEAR_RX_FIFO), .width(1)) sr_clear_rx
-     (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out(),.changed(clear_rx));
+   wire 	 clear_fifo;
 
-   setting_reg #(.my_addr(SR_CLEAR_TX_FIFO), .width(1)) sr_clear_tx
+   setting_reg #(.my_addr(SR_CLEAR_FIFO), .width(1)) sr_clear_fifo
      (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out(),.changed(clear_tx));
+      .in(set_data),.out(),.changed(clear_fifo));
+
+   wire 	 run_rx0, run_rx1;
 
    gpmc #(.TXFIFOSIZE(TXFIFOSIZE), .RXFIFOSIZE(RXFIFOSIZE))
    gpmc (.arst(wb_rst),
@@ -126,7 +124,7 @@ module u1e_core
 	 .wb_sel_o(m0_sel), .wb_cyc_o(m0_cyc), .wb_stb_o(m0_stb), .wb_we_o(m0_we),
 	 .wb_ack_i(m0_ack),
 	 
-	 .fifo_clk(wb_clk), .fifo_rst(wb_rst), .clear_tx(clear_tx), .clear_rx(clear_rx),
+	 .fifo_clk(wb_clk), .fifo_rst(wb_rst), .clear_tx(clear_fifo), .clear_rx(clear_fifo),
 	 .tx_data_o(tx_data), .tx_src_rdy_o(tx_src_rdy), .tx_dst_rdy_i(tx_dst_rdy),
 	 .rx_data_i(rx_data), .rx_src_rdy_i(rx_src_rdy), .rx_dst_rdy_o(rx_dst_rdy),
 
@@ -142,36 +140,37 @@ module u1e_core
    // /////////////////////////////////////////////////////////////////////////
    // RX ADC Frontend, does IQ Balance, DC Offset, muxing
 
-   wire [23:0] 	 adc_i, adc_q;  // 24 bits is total overkill here, but it matches u2/u2p
-   wire 	 run_rx0, run_rx1;
-   
+   wire [23:0] 	 rx_fe_i, rx_fe_q;  // 24 bits is total overkill here, but it matches u2/u2p
+
    rx_frontend #(.BASE(SR_RX_FRONT)) rx_frontend
      (.clk(wb_clk),.rst(wb_rst),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
       .adc_a({rx_i,4'b00}),.adc_ovf_a(0),
       .adc_b({rx_q,4'b00}),.adc_ovf_b(0),
-      .i_out(adc_i), .q_out(adc_q), .run(run_rx0 | run_rx1), .debug());
+      .i_out(rx_fe_i), .q_out(rx_fe_q), .run(run_rx0 | run_rx1), .debug());
    
    // /////////////////////////////////////////////////////////////////////////
    // DSP RX 0
 
    wire [31:0] 	 sample_rx0;
-   wire 	 strobe_rx0;
+   wire 	 strobe_rx0, clear_rx0;
    wire [35:0] 	 vita_rx_data0;
    wire 	 vita_rx_src_rdy0, vita_rx_dst_rdy0;
    
-   dsp_core_rx #(.BASE(SR_RX_DSP0)) dsp_core_rx0
-     (.clk(wb_clk),.rst(wb_rst),
+   ddc_chain #(.BASE(SR_RX_DSP0), .DSPNO(0)) ddc_chain0
+     (.clk(wb_clk), .rst(wb_rst), .clr(clear_rx0),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
-      .adc_i(adc_i),.adc_ovf_i(0),.adc_q(adc_q),.adc_ovf_q(0),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
+      .rx_fe_i(rx_fe_i),.rx_fe_q(rx_fe_q),
       .sample(sample_rx0), .run(run_rx0), .strobe(strobe_rx0),
       .debug() );
 
-   vita_rx_chain #(.BASE(SR_RX_CTRL0), .UNIT(0), .FIFOSIZE(10), .PROT_ENG_FLAGS(0)) vita_rx_chain0
-     (.clk(wb_clk),.reset(wb_rst),.clear(clear_rx),
+   vita_rx_chain #(.BASE(SR_RX_CTRL0), .UNIT(0), .FIFOSIZE(10), .PROT_ENG_FLAGS(0), .DSP_NUMBER(0)) vita_rx_chain0
+     (.clk(wb_clk),.reset(wb_rst),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
       .vita_time(vita_time), .overrun(rx_overrun_dsp0),
-      .sample(sample_rx0), .run(run_rx0), .strobe(strobe_rx0),
+      .sample(sample_rx0), .run(run_rx0), .strobe(strobe_rx0), .clear_o(clear_rx0),
       .rx_data_o(vita_rx_data0), .rx_dst_rdy_i(vita_rx_dst_rdy0), .rx_src_rdy_o(vita_rx_src_rdy0),
       .debug() );
    
@@ -179,22 +178,24 @@ module u1e_core
    // DSP RX 1
 
    wire [31:0] 	 sample_rx1;
-   wire 	 strobe_rx1;
+   wire 	 strobe_rx1, clear_rx1;
    wire [35:0] 	 vita_rx_data1;
    wire 	 vita_rx_src_rdy1, vita_rx_dst_rdy1;
    
-   dsp_core_rx #(.BASE(SR_RX_DSP1)) dsp_core_rx1
-     (.clk(wb_clk),.rst(wb_rst),
+   ddc_chain #(.BASE(SR_RX_DSP1), .DSPNO(1)) ddc_chain1
+     (.clk(wb_clk),.rst(wb_rst), .clr(clear_rx1),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
-      .adc_i(adc_i),.adc_ovf_i(0),.adc_q(adc_q),.adc_ovf_q(0),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
+      .rx_fe_i(rx_fe_i),.rx_fe_q(rx_fe_q),
       .sample(sample_rx1), .run(run_rx1), .strobe(strobe_rx1),
       .debug() );
 
-   vita_rx_chain #(.BASE(SR_RX_CTRL1), .UNIT(1), .FIFOSIZE(10), .PROT_ENG_FLAGS(0)) vita_rx_chain1
-     (.clk(wb_clk),.reset(wb_rst),.clear(clear_rx),
+   vita_rx_chain #(.BASE(SR_RX_CTRL1), .UNIT(1), .FIFOSIZE(10), .PROT_ENG_FLAGS(0), .DSP_NUMBER(1)) vita_rx_chain1
+     (.clk(wb_clk),.reset(wb_rst),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
       .vita_time(vita_time), .overrun(rx_overrun_dsp1),
-      .sample(sample_rx1), .run(run_rx1), .strobe(strobe_rx1),
+      .sample(sample_rx1), .run(run_rx1), .strobe(strobe_rx1), .clear_o(clear_rx1),
       .rx_data_o(vita_rx_data1), .rx_dst_rdy_i(vita_rx_dst_rdy1), .rx_src_rdy_o(vita_rx_src_rdy1),
       .debug() );
 
@@ -202,7 +203,7 @@ module u1e_core
    // RX Stream muxing
 
    fifo36_mux #(.prio(0)) mux_data_streams
-     (.clk(wb_clk), .reset(wb_rst), .clear(0),
+     (.clk(wb_clk), .reset(wb_rst), .clear(clear_fifo),
       .data0_i(vita_rx_data0), .src0_rdy_i(vita_rx_src_rdy0), .dst0_rdy_o(vita_rx_dst_rdy0),
       .data1_i(vita_rx_data1), .src1_rdy_i(vita_rx_src_rdy1), .dst1_rdy_o(vita_rx_dst_rdy1),
       .data_o(rx_data), .src_rdy_o(rx_src_rdy), .dst_rdy_i(rx_dst_rdy));
@@ -210,27 +211,38 @@ module u1e_core
    // ///////////////////////////////////////////////////////////////////////////////////
    // DSP TX
 
-   wire [23:0] 	 tx_i_int, tx_q_int;
    wire 	 run_tx;
-   
-   vita_tx_chain #(.BASE_CTRL(SR_TX_CTRL), .BASE_DSP(SR_TX_DSP), 
+   wire [23:0] 	 tx_fe_i, tx_fe_q;
+   wire [31:0]   sample_tx;
+   wire strobe_tx, clear_tx;
+
+   vita_tx_chain #(.BASE(SR_TX_CTRL), .FIFOSIZE(10), .POST_ENGINE_FIFOSIZE(11),
 		   .REPORT_ERROR(1), .DO_FLOW_CONTROL(0),
 		   .PROT_ENG_FLAGS(0), .USE_TRANS_HEADER(0),
 		   .DSP_NUMBER(0)) 
    vita_tx_chain
      (.clk(wb_clk), .reset(wb_rst),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
       .vita_time(vita_time),
       .tx_data_i(tx_data), .tx_src_rdy_i(tx_src_rdy), .tx_dst_rdy_o(tx_dst_rdy),
       .err_data_o(tx_err_data), .err_src_rdy_o(tx_err_src_rdy), .err_dst_rdy_i(tx_err_dst_rdy),
-      .tx_i(tx_i_int),.tx_q(tx_q_int),
-      .underrun(tx_underrun_dsp), .run(run_tx),
+      .sample(sample_tx), .strobe(strobe_tx),
+      .underrun(tx_underrun_dsp), .run(run_tx), .clear_o(clear_tx),
       .debug(debug_vt));
 
+   duc_chain #(.BASE(SR_TX_DSP), .DSPNO(0)) duc_chain
+     (.clk(wb_clk), .rst(wb_rst), .clr(clear_tx),
+      .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
+      .tx_fe_i(tx_fe_i),.tx_fe_q(tx_fe_q),
+      .sample(sample_tx), .run(run_tx), .strobe(strobe_tx),
+      .debug() );
+
    tx_frontend #(.BASE(SR_TX_FRONT), .WIDTH_OUT(14)) tx_frontend
      (.clk(wb_clk), .rst(wb_rst),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
-      .tx_i(tx_i_int), .tx_q(tx_q_int), .run(1'b1),
+      .tx_i(tx_fe_i), .tx_q(tx_fe_q), .run(1'b1),
       .dac_a(tx_i), .dac_b(tx_q));
 
    // /////////////////////////////////////////////////////////////////////////////////////
@@ -432,11 +444,17 @@ module u1e_core
       .wb_stb_i(s8_stb),.wb_we_i(s8_we),.wb_ack_o(s8_ack),
       .strobe(set_stb),.addr(set_addr),.data(set_data) );
 
+   user_settings #(.BASE(SR_USER_REGS)) user_settings
+     (.clk(wb_clk),.rst(wb_rst),.set_stb(set_stb),
+      .set_addr(set_addr),.set_data(set_data),
+      .set_addr_user(set_addr_user),.set_data_user(set_data_user),
+      .set_stb_user(set_stb_user) );
+
    // /////////////////////////////////////////////////////////////////////////
    // Readback mux 32 -- Slave #7
 
    //compatibility number -> increment when the fpga has been sufficiently altered
-   localparam compat_num = {16'd8, 16'd1}; //major, minor
+   localparam compat_num = {16'd9, 16'd0}; //major, minor
 
    wire [31:0] reg_test32;
 
@@ -462,7 +480,7 @@ module u1e_core
    // /////////////////////////////////////////////////////////////////////////
    // VITA Timing
 
-   time_64bit #(.TICKS_PER_SEC(32'd64000000),.BASE(SR_TIME64)) time_64bit
+   time_64bit #(.BASE(SR_TIME64)) time_64bit
      (.clk(wb_clk), .rst(wb_rst), .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
       .pps(pps_in), .vita_time(vita_time), .vita_time_pps(vita_time_pps), .pps_int(pps_int),
       .exp_time_in(0));
diff --git a/fpga/usrp2/top/N2x0/Makefile.N200R3 b/fpga/usrp2/top/N2x0/Makefile.N200R3
index 9ed5ece00..680cadf44 100644
--- a/fpga/usrp2/top/N2x0/Makefile.N200R3
+++ b/fpga/usrp2/top/N2x0/Makefile.N200R3
@@ -1,5 +1,5 @@
 #
-# Copyright 2008 Ettus Research LLC
+# Copyright 2008-2012 Ettus Research LLC
 #
 
 ##################################################
@@ -8,6 +8,10 @@
 TOP_MODULE = u2plus
 BUILD_DIR = $(abspath build$(ISE)-N200R3)
 
+# set me in a custom makefile
+CUSTOM_SRCS =
+CUSTOM_DEFS =
+
 ##################################################
 # Include other makefiles
 ##################################################
@@ -52,7 +56,8 @@ u2plus.ucf
 SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \
 $(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \
 $(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \
-$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS)
+$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS) \
+$(CUSTOM_SRCS)
 
 ##################################################
 # Process Properties
@@ -65,7 +70,8 @@ SYNTHESIZE_PROPERTIES = \
 "Register Balancing" Yes \
 "Use Clock Enable" Auto \
 "Use Synchronous Reset" Auto \
-"Use Synchronous Set" Auto
+"Use Synchronous Set" Auto \
+"Verilog Macros" "$(CUSTOM_DEFS)"
 
 TRANSLATE_PROPERTIES = \
 "Macro Search Path" "$(shell pwd)/../../coregen/"
diff --git a/fpga/usrp2/top/N2x0/Makefile.N200R4 b/fpga/usrp2/top/N2x0/Makefile.N200R4
index f8640224f..5c9ffd7a6 100644
--- a/fpga/usrp2/top/N2x0/Makefile.N200R4
+++ b/fpga/usrp2/top/N2x0/Makefile.N200R4
@@ -1,5 +1,5 @@
 #
-# Copyright 2008 Ettus Research LLC
+# Copyright 2008-2012 Ettus Research LLC
 #
 
 ##################################################
@@ -8,6 +8,10 @@
 TOP_MODULE = u2plus
 BUILD_DIR = $(abspath build$(ISE)-N200R4)
 
+# set me in a custom makefile
+CUSTOM_SRCS =
+CUSTOM_DEFS =
+
 ##################################################
 # Include other makefiles
 ##################################################
@@ -53,7 +57,8 @@ u2plus.ucf
 SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \
 $(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \
 $(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \
-$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS)
+$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS) \
+$(CUSTOM_SRCS)
 
 ##################################################
 # Process Properties
@@ -67,7 +72,7 @@ SYNTHESIZE_PROPERTIES = \
 "Use Clock Enable" Auto \
 "Use Synchronous Reset" Auto \
 "Use Synchronous Set" Auto \
-"Verilog Macros" "LVDS=1"
+"Verilog Macros" "LVDS=1 $(CUSTOM_DEFS)"
 
 TRANSLATE_PROPERTIES = \
 "Macro Search Path" "$(shell pwd)/../../coregen/"
diff --git a/fpga/usrp2/top/N2x0/Makefile.N210R3 b/fpga/usrp2/top/N2x0/Makefile.N210R3
index 2937dc409..0b53ac951 100644
--- a/fpga/usrp2/top/N2x0/Makefile.N210R3
+++ b/fpga/usrp2/top/N2x0/Makefile.N210R3
@@ -1,5 +1,5 @@
 #
-# Copyright 2008 Ettus Research LLC
+# Copyright 2008-2012 Ettus Research LLC
 #
 
 ##################################################
@@ -8,6 +8,10 @@
 TOP_MODULE = u2plus
 BUILD_DIR = $(abspath build$(ISE)-N210R3)
 
+# set me in a custom makefile
+CUSTOM_SRCS =
+CUSTOM_DEFS =
+
 ##################################################
 # Include other makefiles
 ##################################################
@@ -52,7 +56,8 @@ u2plus.ucf
 SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \
 $(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \
 $(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \
-$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS)
+$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS) \
+$(CUSTOM_SRCS)
 
 ##################################################
 # Process Properties
@@ -65,7 +70,8 @@ SYNTHESIZE_PROPERTIES = \
 "Register Balancing" Yes \
 "Use Clock Enable" Auto \
 "Use Synchronous Reset" Auto \
-"Use Synchronous Set" Auto
+"Use Synchronous Set" Auto \
+"Verilog Macros" "$(CUSTOM_DEFS)"
 
 TRANSLATE_PROPERTIES = \
 "Macro Search Path" "$(shell pwd)/../../coregen/"
diff --git a/fpga/usrp2/top/N2x0/Makefile.N210R4 b/fpga/usrp2/top/N2x0/Makefile.N210R4
index 39a2508f9..a7d2a9b49 100644
--- a/fpga/usrp2/top/N2x0/Makefile.N210R4
+++ b/fpga/usrp2/top/N2x0/Makefile.N210R4
@@ -1,5 +1,5 @@
 #
-# Copyright 2008 Ettus Research LLC
+# Copyright 2008-2012 Ettus Research LLC
 #
 
 ##################################################
@@ -8,6 +8,10 @@
 TOP_MODULE = u2plus
 BUILD_DIR = $(abspath build$(ISE)-N210R4)
 
+# set me in a custom makefile
+CUSTOM_SRCS =
+CUSTOM_DEFS =
+
 ##################################################
 # Include other makefiles
 ##################################################
@@ -53,7 +57,8 @@ u2plus.ucf
 SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \
 $(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \
 $(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \
-$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS)
+$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS) \
+$(CUSTOM_SRCS)
 
 ##################################################
 # Process Properties
@@ -67,7 +72,7 @@ SYNTHESIZE_PROPERTIES = \
 "Use Clock Enable" Auto \
 "Use Synchronous Reset" Auto \
 "Use Synchronous Set" Auto \
-"Verilog Macros" "LVDS=1"
+"Verilog Macros" "LVDS=1 $(CUSTOM_DEFS)"
 
 TRANSLATE_PROPERTIES = \
 "Macro Search Path" "$(shell pwd)/../../coregen/"
diff --git a/fpga/usrp2/top/N2x0/u2plus_core.v b/fpga/usrp2/top/N2x0/u2plus_core.v
index 3ead0db8e..378f212e4 100644
--- a/fpga/usrp2/top/N2x0/u2plus_core.v
+++ b/fpga/usrp2/top/N2x0/u2plus_core.v
@@ -1,5 +1,5 @@
 //
-// Copyright 2011 Ettus Research LLC
+// Copyright 2011-2012 Ettus Research LLC
 //
 // This program is free software: you can redistribute it and/or modify
 // it under the terms of the GNU General Public License as published by
@@ -152,7 +152,7 @@ module u2plus_core
    localparam SR_SIMTIMER =   8;   // 2
    localparam SR_TIME64   =  10;   // 6
    localparam SR_BUF_POOL =  16;   // 4
-
+   localparam SR_USER_REGS = 20;   // 2
    localparam SR_RX_FRONT =  24;   // 5
    localparam SR_RX_CTRL0 =  32;   // 9
    localparam SR_RX_DSP0  =  48;   // 7
@@ -170,15 +170,16 @@ module u2plus_core
    // all (most?) are 36 bits wide, so 9 is 1 BRAM, 10 is 2, 11 is 4 BRAMs
    // localparam DSP_TX_FIFOSIZE = 9;  unused -- DSPTX uses extram fifo
    localparam DSP_RX_FIFOSIZE = 10;
+   localparam DSP_TX_FIFOSIZE = 10;
    localparam ETH_TX_FIFOSIZE = 9;
    localparam ETH_RX_FIFOSIZE = 11;
    localparam SERDES_TX_FIFOSIZE = 9;
    localparam SERDES_RX_FIFOSIZE = 9;  // RX currently doesn't use a fifo?
-   
-   wire [7:0] 	set_addr, set_addr_dsp;
-   wire [31:0] 	set_data, set_data_dsp;
-   wire 	set_stb, set_stb_dsp;
-   
+
+   wire [7:0]  set_addr, set_addr_dsp, set_addr_user;
+   wire [31:0] set_data, set_data_dsp, set_data_user;
+   wire        set_stb, set_stb_dsp, set_stb_user;
+
    reg 		wb_rst; 
    wire 	dsp_rst = wb_rst;
    
@@ -435,7 +436,7 @@ module u2plus_core
    // Buffer Pool Status -- Slave #5   
    
    //compatibility number -> increment when the fpga has been sufficiently altered
-   localparam compat_num = {16'd8, 16'd2}; //major, minor
+   localparam compat_num = {16'd9, 16'd0}; //major, minor
 
    wb_readback_mux buff_pool_status
      (.wb_clk_i(wb_clk), .wb_rst_i(wb_rst), .wb_stb_i(s5_stb),
@@ -478,7 +479,13 @@ module u2plus_core
    settings_bus_crossclock settings_bus_crossclock
      (.clk_i(wb_clk), .rst_i(wb_rst), .set_stb_i(set_stb), .set_addr_i(set_addr), .set_data_i(set_data),
       .clk_o(dsp_clk), .rst_o(dsp_rst), .set_stb_o(set_stb_dsp), .set_addr_o(set_addr_dsp), .set_data_o(set_data_dsp));
-   
+
+   user_settings #(.BASE(SR_USER_REGS)) user_settings
+     (.clk(dsp_clk),.rst(dsp_rst),.set_stb(set_stb_dsp),
+      .set_addr(set_addr_dsp),.set_data(set_data_dsp),
+      .set_addr_user(set_addr_user),.set_data_user(set_data_user),
+      .set_stb_user(set_stb_user) );
+
    // Output control lines
    wire [7:0] 	 clock_outs, serdes_outs, adc_outs;
    assign 	 {clock_ready, clk_en[1:0], clk_sel[1:0]} = clock_outs[4:0];
@@ -559,68 +566,62 @@ module u2plus_core
 
    // /////////////////////////////////////////////////////////////////////////
    // ADC Frontend
-   wire [23:0] 	 adc_i, adc_q;
+   wire [23:0] 	 rx_fe_i, rx_fe_q;
    
    rx_frontend #(.BASE(SR_RX_FRONT)) rx_frontend
      (.clk(dsp_clk),.rst(dsp_rst),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
       .adc_a({adc_a,2'b00}),.adc_ovf_a(adc_ovf_a),
       .adc_b({adc_b,2'b00}),.adc_ovf_b(adc_ovf_b),
-      .i_out(adc_i), .q_out(adc_q), .run(run_rx0_d1 | run_rx1_d1), .debug());
+      .i_out(rx_fe_i), .q_out(rx_fe_q), .run(run_rx0_d1 | run_rx1_d1), .debug());
    
    // /////////////////////////////////////////////////////////////////////////
    // DSP RX 0
    wire [31:0] 	 sample_rx0;
-   wire 	 clear_rx0, strobe_rx0;
+   wire 	 strobe_rx0, clear_rx0;
 
    always @(posedge dsp_clk)
      run_rx0_d1 <= run_rx0;
    
-   dsp_core_rx #(.BASE(SR_RX_DSP0)) dsp_core_rx0
-     (.clk(dsp_clk),.rst(dsp_rst),
+   ddc_chain #(.BASE(SR_RX_DSP0), .DSPNO(0)) ddc_chain0
+     (.clk(dsp_clk), .rst(dsp_rst), .clr(clear_rx0),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
-      .adc_i(adc_i),.adc_ovf_i(adc_ovf_a),.adc_q(adc_q),.adc_ovf_q(adc_ovf_b),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
+      .rx_fe_i(rx_fe_i),.rx_fe_q(rx_fe_q),
       .sample(sample_rx0), .run(run_rx0_d1), .strobe(strobe_rx0),
       .debug() );
 
-   setting_reg #(.my_addr(SR_RX_CTRL0+3)) sr_clear_rx0
-     (.clk(dsp_clk),.rst(dsp_rst),
-      .strobe(set_stb_dsp),.addr(set_addr_dsp),.in(set_data_dsp),
-      .out(),.changed(clear_rx0));
-
-   vita_rx_chain #(.BASE(SR_RX_CTRL0),.UNIT(0),.FIFOSIZE(DSP_RX_FIFOSIZE)) vita_rx_chain0
-     (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx0),
+   vita_rx_chain #(.BASE(SR_RX_CTRL0),.UNIT(0),.FIFOSIZE(DSP_RX_FIFOSIZE), .DSP_NUMBER(0)) vita_rx_chain0
+     (.clk(dsp_clk), .reset(dsp_rst),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
       .vita_time(vita_time), .overrun(overrun0),
-      .sample(sample_rx0), .run(run_rx0), .strobe(strobe_rx0),
+      .sample(sample_rx0), .run(run_rx0), .strobe(strobe_rx0), .clear_o(clear_rx0),
       .rx_data_o(wr1_dat), .rx_src_rdy_o(wr1_ready_i), .rx_dst_rdy_i(wr1_ready_o),
       .debug() );
 
    // /////////////////////////////////////////////////////////////////////////
    // DSP RX 1
    wire [31:0] 	 sample_rx1;
-   wire 	 clear_rx1, strobe_rx1;
+   wire 	 strobe_rx1, clear_rx1;
 
    always @(posedge dsp_clk)
      run_rx1_d1 <= run_rx1;
    
-   dsp_core_rx #(.BASE(SR_RX_DSP1)) dsp_core_rx1
-     (.clk(dsp_clk),.rst(dsp_rst),
+   ddc_chain #(.BASE(SR_RX_DSP1), .DSPNO(1)) ddc_chain1
+     (.clk(dsp_clk), .rst(dsp_rst), .clr(clear_rx1),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
-      .adc_i(adc_i),.adc_ovf_i(adc_ovf_a),.adc_q(adc_q),.adc_ovf_q(adc_ovf_b),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
+      .rx_fe_i(rx_fe_i),.rx_fe_q(rx_fe_q),
       .sample(sample_rx1), .run(run_rx1_d1), .strobe(strobe_rx1),
       .debug() );
 
-   setting_reg #(.my_addr(SR_RX_CTRL1+3)) sr_clear_rx1
-     (.clk(dsp_clk),.rst(dsp_rst),
-      .strobe(set_stb_dsp),.addr(set_addr_dsp),.in(set_data_dsp),
-      .out(),.changed(clear_rx1));
-
-   vita_rx_chain #(.BASE(SR_RX_CTRL1),.UNIT(2),.FIFOSIZE(DSP_RX_FIFOSIZE)) vita_rx_chain1
-     (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx1),
+   vita_rx_chain #(.BASE(SR_RX_CTRL1),.UNIT(2),.FIFOSIZE(DSP_RX_FIFOSIZE), .DSP_NUMBER(1)) vita_rx_chain1
+     (.clk(dsp_clk), .reset(dsp_rst),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
       .vita_time(vita_time), .overrun(overrun1),
-      .sample(sample_rx1), .run(run_rx1), .strobe(strobe_rx1),
+      .sample(sample_rx1), .run(run_rx1), .strobe(strobe_rx1), .clear_o(clear_rx1),
       .rx_data_o(wr3_dat), .rx_src_rdy_o(wr3_ready_i), .rx_dst_rdy_i(wr3_ready_o),
       .debug() );
 
@@ -632,10 +633,6 @@ module u2plus_core
    wire [31:0] 	 debug_vt;
    wire 	 clear_tx;
 
-   setting_reg #(.my_addr(SR_TX_CTRL+1)) sr_clear_tx
-     (.clk(dsp_clk),.rst(dsp_rst),.strobe(set_stb_dsp),.addr(set_addr_dsp),
-      .in(set_data_dsp),.out(),.changed(clear_tx));
-
    assign 	 RAM_A[20:18] = 3'b0;
    
    ext_fifo #(.EXT_WIDTH(36),.INT_WIDTH(36),.RAM_DEPTH(18),.FIFO_DEPTH(18)) 
@@ -661,28 +658,39 @@ module u2plus_core
 	.debug(debug_extfifo),
 	.debug2(debug_extfifo2) );
 
-   wire [23:0] 	 tx_i, tx_q;
+   wire [23:0] 	 tx_fe_i, tx_fe_q;
+   wire [31:0]   sample_tx;
+   wire strobe_tx;
    
-   vita_tx_chain #(.BASE_CTRL(SR_TX_CTRL), .BASE_DSP(SR_TX_DSP), 
+   vita_tx_chain #(.BASE(SR_TX_CTRL), .FIFOSIZE(DSP_TX_FIFOSIZE),
 		   .REPORT_ERROR(1), .DO_FLOW_CONTROL(1),
 		   .PROT_ENG_FLAGS(1), .USE_TRANS_HEADER(1),
 		   .DSP_NUMBER(0))
    vita_tx_chain
      (.clk(dsp_clk), .reset(dsp_rst),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
       .vita_time(vita_time),
       .tx_data_i(tx_data), .tx_src_rdy_i(tx_src_rdy), .tx_dst_rdy_o(tx_dst_rdy),
       .err_data_o(tx_err_data), .err_src_rdy_o(tx_err_src_rdy), .err_dst_rdy_i(tx_err_dst_rdy),
-      .tx_i(tx_i),.tx_q(tx_q),
-      .underrun(underrun), .run(run_tx),
+      .sample(sample_tx), .strobe(strobe_tx),
+      .underrun(underrun), .run(run_tx), .clear_o(clear_tx),
       .debug(debug_vt));
 
+   duc_chain #(.BASE(SR_TX_DSP), .DSPNO(0)) duc_chain
+     (.clk(dsp_clk),.rst(dsp_rst), .clr(clear_tx),
+      .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
+      .tx_fe_i(tx_fe_i),.tx_fe_q(tx_fe_q),
+      .sample(sample_tx), .run(run_tx), .strobe(strobe_tx),
+      .debug() );
+
    tx_frontend #(.BASE(SR_TX_FRONT)) tx_frontend
      (.clk(dsp_clk), .rst(dsp_rst),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
-      .tx_i(tx_i), .tx_q(tx_q), .run(1'b1),
+      .tx_i(tx_fe_i), .tx_q(tx_fe_q), .run(1'b1),
       .dac_a(dac_a), .dac_b(dac_b));
-         
+
    // ///////////////////////////////////////////////////////////////////////////////////
    // SERDES
 
@@ -701,7 +709,7 @@ module u2plus_core
 
    wire [31:0] 	 debug_sync;
 
-   time_64bit #(.TICKS_PER_SEC(32'd100000000),.BASE(SR_TIME64)) time_64bit
+   time_64bit #(.BASE(SR_TIME64)) time_64bit
      (.clk(dsp_clk), .rst(dsp_rst), .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
       .pps(pps_in), .vita_time(vita_time), .vita_time_pps(vita_time_pps), .pps_int(pps_int),
       .exp_time_in(exp_time_in), .exp_time_out(exp_time_out), .good_sync(good_sync), .debug(debug_sync));
diff --git a/fpga/usrp2/top/USRP2/Makefile b/fpga/usrp2/top/USRP2/Makefile
index 8ebb43639..1fc375c76 100644
--- a/fpga/usrp2/top/USRP2/Makefile
+++ b/fpga/usrp2/top/USRP2/Makefile
@@ -1,5 +1,5 @@
 #
-# Copyright 2008 Ettus Research LLC
+# Copyright 2008-2012 Ettus Research LLC
 #
 
 ##################################################
@@ -8,6 +8,10 @@
 TOP_MODULE = u2_rev3
 BUILD_DIR = $(abspath build)
 
+# set me in a custom makefile
+CUSTOM_SRCS =
+CUSTOM_DEFS =
+
 ##################################################
 # Include other makefiles
 ##################################################
@@ -52,7 +56,8 @@ u2_rev3.ucf
 SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \
 $(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \
 $(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \
-$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS)
+$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS) \
+$(CUSTOM_SRCS)
 
 ##################################################
 # Process Properties
@@ -65,7 +70,8 @@ SYNTHESIZE_PROPERTIES = \
 "Register Balancing" Yes \
 "Use Clock Enable" Auto \
 "Use Synchronous Reset" Auto \
-"Use Synchronous Set" Auto
+"Use Synchronous Set" Auto \
+"Verilog Macros" "$(CUSTOM_DEFS)"
 
 TRANSLATE_PROPERTIES = \
 "Macro Search Path" "$(shell pwd)/../../coregen/"
diff --git a/fpga/usrp2/top/USRP2/u2_core.v b/fpga/usrp2/top/USRP2/u2_core.v
index bbd0e9337..9b26b98e1 100644
--- a/fpga/usrp2/top/USRP2/u2_core.v
+++ b/fpga/usrp2/top/USRP2/u2_core.v
@@ -1,5 +1,5 @@
 //
-// Copyright 2011 Ettus Research LLC
+// Copyright 2011-2012 Ettus Research LLC
 //
 // This program is free software: you can redistribute it and/or modify
 // it under the terms of the GNU General Public License as published by
@@ -157,7 +157,7 @@ module u2_core
    localparam SR_SIMTIMER =   8;   // 2
    localparam SR_TIME64   =  10;   // 6
    localparam SR_BUF_POOL =  16;   // 4
-
+   localparam SR_USER_REGS = 20;   // 2
    localparam SR_RX_FRONT =  24;   // 5
    localparam SR_RX_CTRL0 =  32;   // 9
    localparam SR_RX_DSP0  =  48;   // 7
@@ -175,15 +175,16 @@ module u2_core
    // all (most?) are 36 bits wide, so 9 is 1 BRAM, 10 is 2, 11 is 4 BRAMs
    // localparam DSP_TX_FIFOSIZE = 9;  unused -- DSPTX uses extram fifo
    localparam DSP_RX_FIFOSIZE = 10;
+   localparam DSP_TX_FIFOSIZE = 10;
    localparam ETH_TX_FIFOSIZE = 9;
    localparam ETH_RX_FIFOSIZE = 11;
    localparam SERDES_TX_FIFOSIZE = 9;
    localparam SERDES_RX_FIFOSIZE = 9;  // RX currently doesn't use a fifo?
-   
-   wire [7:0] 	set_addr, set_addr_dsp;
-   wire [31:0] 	set_data, set_data_dsp;
-   wire 	set_stb, set_stb_dsp;
-   
+
+   wire [7:0]  set_addr, set_addr_dsp, set_addr_user;
+   wire [31:0] set_data, set_data_dsp, set_data_user;
+   wire        set_stb, set_stb_dsp, set_stb_user;
+
    wire 	ram_loader_done, ram_loader_rst;
    wire 	wb_rst;
    wire 	dsp_rst = wb_rst;
@@ -441,7 +442,7 @@ module u2_core
    // Buffer Pool Status -- Slave #5   
    
    //compatibility number -> increment when the fpga has been sufficiently altered
-   localparam compat_num = {16'd8, 16'd2}; //major, minor
+   localparam compat_num = {16'd9, 16'd0}; //major, minor
 
    wb_readback_mux buff_pool_status
      (.wb_clk_i(wb_clk), .wb_rst_i(wb_rst), .wb_stb_i(s5_stb),
@@ -484,7 +485,13 @@ module u2_core
    settings_bus_crossclock settings_bus_crossclock
      (.clk_i(wb_clk), .rst_i(wb_rst), .set_stb_i(set_stb), .set_addr_i(set_addr), .set_data_i(set_data),
       .clk_o(dsp_clk), .rst_o(dsp_rst), .set_stb_o(set_stb_dsp), .set_addr_o(set_addr_dsp), .set_data_o(set_data_dsp));
-   
+
+   user_settings #(.BASE(SR_USER_REGS)) user_settings
+     (.clk(dsp_clk),.rst(dsp_rst),.set_stb(set_stb_dsp),
+      .set_addr(set_addr_dsp),.set_data(set_data_dsp),
+      .set_addr_user(set_addr_user),.set_data_user(set_data_user),
+      .set_stb_user(set_stb_user) );
+
    // Output control lines
    wire [7:0] 	 clock_outs, serdes_outs, adc_outs;
    assign 	 {clock_ready, clk_en[1:0], clk_sel[1:0]} = clock_outs[4:0];
@@ -547,68 +554,62 @@ module u2_core
 
    // /////////////////////////////////////////////////////////////////////////
    // ADC Frontend
-   wire [23:0] 	 adc_i, adc_q;
+   wire [23:0] 	 rx_fe_i, rx_fe_q;
    
    rx_frontend #(.BASE(SR_RX_FRONT)) rx_frontend
      (.clk(dsp_clk),.rst(dsp_rst),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
       .adc_a({adc_a,2'b00}),.adc_ovf_a(adc_ovf_a),
       .adc_b({adc_b,2'b00}),.adc_ovf_b(adc_ovf_b),
-      .i_out(adc_i), .q_out(adc_q), .run(run_rx0_d1 | run_rx1_d1), .debug());
+      .i_out(rx_fe_i), .q_out(rx_fe_q), .run(run_rx0_d1 | run_rx1_d1), .debug());
    
    // /////////////////////////////////////////////////////////////////////////
    // DSP RX 0
    wire [31:0] 	 sample_rx0;
-   wire 	 clear_rx0, strobe_rx0;
+   wire 	 strobe_rx0, clear_rx0;
 
    always @(posedge dsp_clk)
      run_rx0_d1 <= run_rx0;
    
-   dsp_core_rx #(.BASE(SR_RX_DSP0)) dsp_core_rx0
-     (.clk(dsp_clk),.rst(dsp_rst),
+   ddc_chain #(.BASE(SR_RX_DSP0), .DSPNO(0)) ddc_chain0
+     (.clk(dsp_clk), .rst(dsp_rst), .clr(clear_rx0),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
-      .adc_i(adc_i),.adc_ovf_i(adc_ovf_a),.adc_q(adc_q),.adc_ovf_q(adc_ovf_b),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
+      .rx_fe_i(rx_fe_i),.rx_fe_q(rx_fe_q),
       .sample(sample_rx0), .run(run_rx0_d1), .strobe(strobe_rx0),
       .debug() );
 
-   setting_reg #(.my_addr(SR_RX_CTRL0+3)) sr_clear_rx0
-     (.clk(dsp_clk),.rst(dsp_rst),
-      .strobe(set_stb_dsp),.addr(set_addr_dsp),.in(set_data_dsp),
-      .out(),.changed(clear_rx0));
-
-   vita_rx_chain #(.BASE(SR_RX_CTRL0),.UNIT(0),.FIFOSIZE(DSP_RX_FIFOSIZE)) vita_rx_chain0
-     (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx0),
+   vita_rx_chain #(.BASE(SR_RX_CTRL0),.UNIT(0),.FIFOSIZE(DSP_RX_FIFOSIZE), .DSP_NUMBER(0)) vita_rx_chain0
+     (.clk(dsp_clk), .reset(dsp_rst),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
       .vita_time(vita_time), .overrun(overrun0),
-      .sample(sample_rx0), .run(run_rx0), .strobe(strobe_rx0),
+      .sample(sample_rx0), .run(run_rx0), .strobe(strobe_rx0), .clear_o(clear_rx0),
       .rx_data_o(wr1_dat), .rx_src_rdy_o(wr1_ready_i), .rx_dst_rdy_i(wr1_ready_o),
       .debug() );
 
    // /////////////////////////////////////////////////////////////////////////
    // DSP RX 1
    wire [31:0] 	 sample_rx1;
-   wire 	 clear_rx1, strobe_rx1;
+   wire 	 strobe_rx1, clear_rx1;
 
    always @(posedge dsp_clk)
      run_rx1_d1 <= run_rx1;
    
-   dsp_core_rx #(.BASE(SR_RX_DSP1)) dsp_core_rx1
-     (.clk(dsp_clk),.rst(dsp_rst),
+   ddc_chain #(.BASE(SR_RX_DSP1), .DSPNO(1)) ddc_chain1
+     (.clk(dsp_clk), .rst(dsp_rst), .clr(clear_rx1),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
-      .adc_i(adc_i),.adc_ovf_i(adc_ovf_a),.adc_q(adc_q),.adc_ovf_q(adc_ovf_b),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
+      .rx_fe_i(rx_fe_i),.rx_fe_q(rx_fe_q),
       .sample(sample_rx1), .run(run_rx1_d1), .strobe(strobe_rx1),
       .debug() );
 
-   setting_reg #(.my_addr(SR_RX_CTRL1+3)) sr_clear_rx1
-     (.clk(dsp_clk),.rst(dsp_rst),
-      .strobe(set_stb_dsp),.addr(set_addr_dsp),.in(set_data_dsp),
-      .out(),.changed(clear_rx1));
-
-   vita_rx_chain #(.BASE(SR_RX_CTRL1),.UNIT(2),.FIFOSIZE(DSP_RX_FIFOSIZE)) vita_rx_chain1
-     (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx1),
+   vita_rx_chain #(.BASE(SR_RX_CTRL1),.UNIT(2),.FIFOSIZE(DSP_RX_FIFOSIZE), .DSP_NUMBER(1)) vita_rx_chain1
+     (.clk(dsp_clk), .reset(dsp_rst),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
       .vita_time(vita_time), .overrun(overrun1),
-      .sample(sample_rx1), .run(run_rx1), .strobe(strobe_rx1),
+      .sample(sample_rx1), .run(run_rx1), .strobe(strobe_rx1), .clear_o(clear_rx1),
       .rx_data_o(wr3_dat), .rx_src_rdy_o(wr3_ready_i), .rx_dst_rdy_i(wr3_ready_o),
       .debug() );
 
@@ -620,10 +621,6 @@ module u2_core
    wire [31:0] 	 debug_vt;
    wire 	 clear_tx;
 
-   setting_reg #(.my_addr(SR_TX_CTRL+1)) sr_clear_tx
-     (.clk(dsp_clk),.rst(dsp_rst),.strobe(set_stb_dsp),.addr(set_addr_dsp),
-      .in(set_data_dsp),.out(),.changed(clear_tx));
-
    ext_fifo #(.EXT_WIDTH(18),.INT_WIDTH(36),.RAM_DEPTH(19),.FIFO_DEPTH(19)) 
      ext_fifo_i1
        (.int_clk(dsp_clk),
@@ -647,28 +644,39 @@ module u2_core
 	.debug(debug_extfifo),
 	.debug2(debug_extfifo2) );
 
-   wire [23:0] 	 tx_i, tx_q;
+   wire [23:0] 	 tx_fe_i, tx_fe_q;
+   wire [31:0]   sample_tx;
+   wire strobe_tx;
    
-   vita_tx_chain #(.BASE_CTRL(SR_TX_CTRL), .BASE_DSP(SR_TX_DSP), 
+   vita_tx_chain #(.BASE(SR_TX_CTRL), .FIFOSIZE(DSP_TX_FIFOSIZE),
 		   .REPORT_ERROR(1), .DO_FLOW_CONTROL(1),
 		   .PROT_ENG_FLAGS(1), .USE_TRANS_HEADER(1),
 		   .DSP_NUMBER(0))
    vita_tx_chain
      (.clk(dsp_clk), .reset(dsp_rst),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
       .vita_time(vita_time),
       .tx_data_i(tx_data), .tx_src_rdy_i(tx_src_rdy), .tx_dst_rdy_o(tx_dst_rdy),
       .err_data_o(tx_err_data), .err_src_rdy_o(tx_err_src_rdy), .err_dst_rdy_i(tx_err_dst_rdy),
-      .tx_i(tx_i),.tx_q(tx_q),
-      .underrun(underrun), .run(run_tx),
+      .sample(sample_tx), .strobe(strobe_tx),
+      .underrun(underrun), .run(run_tx), .clear_o(clear_tx),
       .debug(debug_vt));
 
+   duc_chain #(.BASE(SR_TX_DSP), .DSPNO(0)) duc_chain
+     (.clk(dsp_clk),.rst(dsp_rst), .clr(clear_tx),
+      .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
+      .tx_fe_i(tx_fe_i),.tx_fe_q(tx_fe_q),
+      .sample(sample_tx), .run(run_tx), .strobe(strobe_tx),
+      .debug() );
+
    tx_frontend #(.BASE(SR_TX_FRONT)) tx_frontend
      (.clk(dsp_clk), .rst(dsp_rst),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
-      .tx_i(tx_i), .tx_q(tx_q), .run(1'b1),
+      .tx_i(tx_fe_i), .tx_q(tx_fe_q), .run(1'b1),
       .dac_a(dac_a), .dac_b(dac_b));
-         
+
    // ///////////////////////////////////////////////////////////////////////////////////
    // SERDES
 
@@ -689,7 +697,7 @@ module u2_core
 
    wire [31:0] 	 debug_sync;
 
-   time_64bit #(.TICKS_PER_SEC(32'd100000000),.BASE(SR_TIME64)) time_64bit
+   time_64bit #(.BASE(SR_TIME64)) time_64bit
      (.clk(dsp_clk), .rst(dsp_rst), .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
       .pps(pps_in), .vita_time(vita_time), .vita_time_pps(vita_time_pps), .pps_int(pps_int),
       .exp_time_in(exp_time_in), .exp_time_out(exp_time_out), .good_sync(good_sync), .debug(debug_sync));
diff --git a/fpga/usrp2/vrt/Makefile.srcs b/fpga/usrp2/vrt/Makefile.srcs
index 166ed44ef..84ba5dc29 100644
--- a/fpga/usrp2/vrt/Makefile.srcs
+++ b/fpga/usrp2/vrt/Makefile.srcs
@@ -15,4 +15,6 @@ vita_tx_chain.v \
 gen_context_pkt.v \
 trigger_context_pkt.v \
 vita_pkt_gen.v \
+vita_rx_engine_glue.v \
+vita_tx_engine_glue.v \
 ))
diff --git a/fpga/usrp2/vrt/gen_context_pkt.v b/fpga/usrp2/vrt/gen_context_pkt.v
index bdfca8237..d6674e887 100644
--- a/fpga/usrp2/vrt/gen_context_pkt.v
+++ b/fpga/usrp2/vrt/gen_context_pkt.v
@@ -32,12 +32,11 @@ module gen_context_pkt
    localparam CTXT_PROT_ENG = 1;
    localparam CTXT_HEADER = 2;
    localparam CTXT_STREAMID = 3;
-   localparam CTXT_SECS = 4;
-   localparam CTXT_TICS = 5;
-   localparam CTXT_TICS2 = 6;
-   localparam CTXT_MESSAGE = 7;
-   localparam CTXT_FLOWCTRL = 8;
-   localparam CTXT_DONE = 9;
+   localparam CTXT_TICS = 4;
+   localparam CTXT_TICS2 = 5;
+   localparam CTXT_MESSAGE = 6;
+   localparam CTXT_FLOWCTRL = 7;
+   localparam CTXT_DONE = 8;
 
    reg [33:0] 	 data_int;
    wire 	 src_rdy_int, dst_rdy_int;
@@ -88,11 +87,10 @@ module gen_context_pkt
 
    always @*
      case(ctxt_state)
-       CTXT_PROT_ENG : data_int <= { 2'b01, 13'b0, DSP_NUMBER[0], 1'b1, 1'b1, 16'd28 }; // UDP port 1 or 3
-       CTXT_HEADER : data_int <= { 1'b0, (PROT_ENG_FLAGS ? 1'b0 : 1'b1), 12'b010100001101, seqno, 16'd7 };
+       CTXT_PROT_ENG : data_int <= { 2'b01, 13'b0, DSP_NUMBER[0], 1'b1, 1'b1, 16'd24 }; // UDP port 1 or 3
+       CTXT_HEADER : data_int <= { 1'b0, (PROT_ENG_FLAGS ? 1'b0 : 1'b1), 12'b010100000001, seqno, 16'd6 };
        CTXT_STREAMID : data_int <= { 2'b00, streamid };
-       CTXT_SECS : data_int <= { 2'b00, err_time[63:32] };
-       CTXT_TICS : data_int <= { 2'b00, 32'd0 };
+       CTXT_TICS : data_int <= { 2'b00, err_time[63:32] };
        CTXT_TICS2 : data_int <= { 2'b00, err_time[31:0] };
        CTXT_MESSAGE : data_int <= { 2'b00, message };
        CTXT_FLOWCTRL : data_int <= { 2'b10, seqnum };
diff --git a/fpga/usrp2/vrt/vita_rx_chain.v b/fpga/usrp2/vrt/vita_rx_chain.v
index 8b41e5fa8..c57e6cc05 100644
--- a/fpga/usrp2/vrt/vita_rx_chain.v
+++ b/fpga/usrp2/vrt/vita_rx_chain.v
@@ -1,5 +1,5 @@
 //
-// Copyright 2011 Ettus Research LLC
+// Copyright 2011-2012 Ettus Research LLC
 //
 // This program is free software: you can redistribute it and/or modify
 // it under the terms of the GNU General Public License as published by
@@ -20,21 +20,31 @@ module vita_rx_chain
   #(parameter BASE=0,
     parameter UNIT=0,
     parameter FIFOSIZE=10,
-    parameter PROT_ENG_FLAGS=1)
-   (input clk, input reset, input clear,
+    parameter PROT_ENG_FLAGS=1,
+    parameter DSP_NUMBER=0)
+   (input clk, input reset,
     input set_stb, input [7:0] set_addr, input [31:0] set_data,
-    input [63:0] vita_time, output overrun,
-    input [31:0] sample, output run, input strobe,
+    input set_stb_user, input [7:0] set_addr_user, input [31:0] set_data_user,
+    input [63:0] vita_time,
+    input [31:0] sample, input strobe,
     output [35:0] rx_data_o, output rx_src_rdy_o, input rx_dst_rdy_i,
+    output overrun, output run, output clear_o,
     output [31:0] debug );
-       
+
    wire [100:0] sample_data;
    wire 	sample_dst_rdy, sample_src_rdy;
    wire [31:0] 	vrc_debug, vrf_debug;
 
    wire [35:0] 	rx_data_int;
    wire 	rx_src_rdy_int, rx_dst_rdy_int;
-   
+
+   wire clear;
+   assign clear_o = clear;
+
+   setting_reg #(.my_addr(BASE+3)) sr
+     (.clk(clk),.rst(reset),.strobe(set_stb),.addr(set_addr),
+      .in(set_data),.out(),.changed(clear));
+
    vita_rx_control #(.BASE(BASE), .WIDTH(32)) vita_rx_control
      (.clk(clk), .reset(reset), .clear(clear),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
@@ -65,9 +75,10 @@ module vita_rx_chain
       .data_i(rx_data_int), .src_rdy_i(rx_src_rdy_int), .dst_rdy_o(rx_dst_rdy_int),
       .data_o(rx_data_int2), .src_rdy_o(rx_src_rdy_int2), .dst_rdy_i(rx_dst_rdy_int2));
 
-   dspengine_16to8 #(.BASE(BASE+9), .BUF_SIZE(FIFOSIZE)) dspengine_16to8
-     (.clk(clk),.reset(reset),.clear(clear),
-      .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
+   vita_rx_engine_glue #(.DSPNO(DSP_NUMBER), .MAIN_SETTINGS_BASE(BASE+3), .BUF_SIZE(FIFOSIZE)) dspengine_rx
+     (.clock(clk),.reset(reset),.clear(clear),
+      .set_stb_main(set_stb), .set_addr_main(set_addr), .set_data_main(set_data),
+      .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
       .access_we(access_we), .access_stb(access_stb), .access_ok(access_ok), .access_done(access_done), 
       .access_skip_read(access_skip_read), .access_adr(access_adr), .access_len(access_len), 
       .access_dat_i(buf_to_dsp), .access_dat_o(dsp_to_buf));
diff --git a/fpga/usrp2/vrt/vita_rx_engine_glue.v b/fpga/usrp2/vrt/vita_rx_engine_glue.v
new file mode 100644
index 000000000..56447a7aa
--- /dev/null
+++ b/fpga/usrp2/vrt/vita_rx_engine_glue.v
@@ -0,0 +1,95 @@
+//
+// Copyright 2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+//The following module is used to re-write receive packets to the host.
+//This module provides a packet-based ram interface for manipulating packets.
+//By default, this module uses the built-in 16 to 8 bit converter engine.
+
+module vita_rx_engine_glue
+#(
+    //the dsp unit number: 0, 1, 2...
+    parameter DSPNO = 0,
+
+    //buffer size for ram interface engine
+    parameter BUF_SIZE = 10,
+
+    //base address for built-in settings registers used in this module
+    parameter MAIN_SETTINGS_BASE = 0
+)
+(
+    //control signals
+    input clock, input reset, input clear,
+
+    //main settings bus for built-in modules
+    input set_stb_main, input [7:0] set_addr_main, input [31:0] set_data_main,
+
+    //user settings bus, controlled through user setting regs API
+    input set_stb_user, input [7:0] set_addr_user, input [31:0] set_data_user,
+
+    //ram interface for engine
+    output access_we,
+    output access_stb,
+    input access_ok,
+    output access_done,
+    output access_skip_read,
+    output [BUF_SIZE-1:0] access_adr,
+    input [BUF_SIZE-1:0] access_len,
+    output [35:0] access_dat_o,
+    input [35:0] access_dat_i,
+
+    //debug output (optional)
+    output [31:0] debug
+);
+
+    generate
+        if (DSPNO==0) begin
+            `ifndef RX_ENG0_MODULE
+            dspengine_16to8 #(.BASE(MAIN_SETTINGS_BASE), .BUF_SIZE(BUF_SIZE)) dspengine_16to8
+             (.clk(clock),.reset(reset),.clear(clear),
+              .set_stb(set_stb_main), .set_addr(set_addr_main), .set_data(set_data_main),
+              .access_we(access_we), .access_stb(access_stb), .access_ok(access_ok), .access_done(access_done), 
+              .access_skip_read(access_skip_read), .access_adr(access_adr), .access_len(access_len), 
+              .access_dat_i(access_dat_i), .access_dat_o(access_dat_o));
+            `else
+            `RX_ENG0_MODULE #(.BUF_SIZE(BUF_SIZE)) rx_eng0_custom
+             (.clock(clock),.reset(reset),.clear(clear),
+              .set_stb(set_stb_user), .set_addr(set_addr_user), .set_data(set_data_user),
+              .access_we(access_we), .access_stb(access_stb), .access_ok(access_ok), .access_done(access_done), 
+              .access_skip_read(access_skip_read), .access_adr(access_adr), .access_len(access_len), 
+              .access_dat_i(access_dat_i), .access_dat_o(access_dat_o));
+            `endif
+        end
+        else begin
+            `ifndef RX_ENG1_MODULE
+            dspengine_16to8 #(.BASE(MAIN_SETTINGS_BASE), .BUF_SIZE(BUF_SIZE)) dspengine_16to8
+             (.clk(clock),.reset(reset),.clear(clear),
+              .set_stb(set_stb_main), .set_addr(set_addr_main), .set_data(set_data_main),
+              .access_we(access_we), .access_stb(access_stb), .access_ok(access_ok), .access_done(access_done), 
+              .access_skip_read(access_skip_read), .access_adr(access_adr), .access_len(access_len), 
+              .access_dat_i(access_dat_i), .access_dat_o(access_dat_o));
+            `else
+            `RX_ENG1_MODULE #(.BUF_SIZE(BUF_SIZE)) rx_eng1_custom
+             (.clock(clock),.reset(reset),.clear(clear),
+              .set_stb(set_stb_user), .set_addr(set_addr_user), .set_data(set_data_user),
+              .access_we(access_we), .access_stb(access_stb), .access_ok(access_ok), .access_done(access_done), 
+              .access_skip_read(access_skip_read), .access_adr(access_adr), .access_len(access_len), 
+              .access_dat_i(access_dat_i), .access_dat_o(access_dat_o));
+            `endif
+        end
+    endgenerate
+
+endmodule //vita_rx_engine_glue
diff --git a/fpga/usrp2/vrt/vita_rx_framer.v b/fpga/usrp2/vrt/vita_rx_framer.v
index bd09315bc..514df1151 100644
--- a/fpga/usrp2/vrt/vita_rx_framer.v
+++ b/fpga/usrp2/vrt/vita_rx_framer.v
@@ -1,5 +1,5 @@
 //
-// Copyright 2011 Ettus Research LLC
+// Copyright 2011-2012 Ettus Research LLC
 //
 // This program is free software: you can redistribute it and/or modify
 // it under the terms of the GNU General Public License as published by
@@ -93,18 +93,16 @@ module vita_rx_framer
    localparam VITA_IDLE 	 = 0;
    localparam VITA_HEADER 	 = 1;
    localparam VITA_STREAMID 	 = 2;
-   localparam VITA_SECS 	 = 3;
-   localparam VITA_TICS 	 = 4;
-   localparam VITA_TICS2 	 = 5;
-   localparam VITA_PAYLOAD 	 = 6;
-   localparam VITA_TRAILER 	 = 7;
-   localparam VITA_ERR_HEADER 	 = 9;  // All ERR at 4'b1000 or'ed with base
-   localparam VITA_ERR_STREAMID  = 10;
-   localparam VITA_ERR_SECS 	 = 11;
-   localparam VITA_ERR_TICS 	 = 12;
-   localparam VITA_ERR_TICS2 	 = 13;
-   localparam VITA_ERR_PAYLOAD 	 = 14;
-   localparam VITA_ERR_TRAILER 	 = 15; // Extension context packets have no trailer
+   localparam VITA_TICS 	 = 3;
+   localparam VITA_TICS2 	 = 4;
+   localparam VITA_PAYLOAD 	 = 5;
+   localparam VITA_TRAILER 	 = 6;
+   localparam VITA_ERR_HEADER 	 = 7;  // All ERR at 4'b1000 or'ed with base
+   localparam VITA_ERR_STREAMID  = 8;
+   localparam VITA_ERR_TICS 	 = 9;
+   localparam VITA_ERR_TICS2 	 = 10;
+   localparam VITA_ERR_PAYLOAD 	 = 11;
+   localparam VITA_ERR_TRAILER 	 = 12; // Extension context packets have no trailer
       
    always @(posedge clk)
      if(reset | clear | clear_pkt_count)
@@ -122,17 +120,15 @@ module vita_rx_framer
        VITA_HEADER : pkt_fifo_line <= {2'b01,3'b000,vita_header[28],2'b01,vita_header[25:24],
 				       vita_header[23:20],pkt_count[3:0],vita_pkt_len[15:0]};
        VITA_STREAMID : pkt_fifo_line <= {2'b00,vita_streamid};
-       VITA_SECS : pkt_fifo_line <= {2'b00,vita_time_fifo_o[63:32]};
-       VITA_TICS : pkt_fifo_line <= {2'b00,32'd0};
+       VITA_TICS : pkt_fifo_line <= {2'b00,vita_time_fifo_o[63:32]};
        VITA_TICS2 : pkt_fifo_line <= {2'b00,vita_time_fifo_o[31:0]};
        VITA_PAYLOAD : pkt_fifo_line <= {2'b00,data_fifo_o};
        VITA_TRAILER : pkt_fifo_line <= {2'b10,vita_trailer[31:21],1'b1,vita_trailer[19:9],trl_eob,8'd0};
 
        // Error packets are Extension Context packets, which have no trailer
-       VITA_ERR_HEADER : pkt_fifo_line <= {2'b01,4'b0101,4'b0000,vita_header[23:20],pkt_count,16'd6};
+       VITA_ERR_HEADER : pkt_fifo_line <= {2'b01,4'b0101,4'b0000,vita_header[23:20],pkt_count,16'd5};
        VITA_ERR_STREAMID : pkt_fifo_line <= {2'b00,vita_streamid};
-       VITA_ERR_SECS : pkt_fifo_line <= {2'b00,vita_time_fifo_o[63:32]};
-       VITA_ERR_TICS : pkt_fifo_line <= {2'b00,32'd0};
+       VITA_ERR_TICS : pkt_fifo_line <= {2'b00,vita_time_fifo_o[63:32]};
        VITA_ERR_TICS2 : pkt_fifo_line <= {2'b00,vita_time_fifo_o[31:0]};
        VITA_ERR_PAYLOAD : pkt_fifo_line <= {2'b10,27'd0,flags_fifo_o};
        //VITA_ERR_TRAILER : pkt_fifo_line <= {2'b11,vita_trailer};
@@ -164,7 +160,7 @@ module vita_rx_framer
 	     if(has_streamid)
 	       vita_state <= VITA_STREAMID;
 	     else
-	       vita_state <= VITA_SECS;
+	       vita_state <= VITA_TICS;
 	   VITA_PAYLOAD :
 	     if(sample_fifo_src_rdy_i)
 	       begin
@@ -194,12 +190,12 @@ module vita_rx_framer
      case(vita_state)
        VITA_IDLE :
 	 req_write_pkt_fifo <= 0;
-       VITA_HEADER, VITA_STREAMID, VITA_SECS, VITA_TICS, VITA_TICS2, VITA_TRAILER :
+       VITA_HEADER, VITA_STREAMID, VITA_TICS, VITA_TICS2, VITA_TRAILER :
 	 req_write_pkt_fifo <= 1;
        VITA_PAYLOAD :
 	 // Write if sample ready and no error flags
      	 req_write_pkt_fifo <= (sample_fifo_src_rdy_i & ~|flags_fifo_o[4:1]);
-       VITA_ERR_HEADER, VITA_ERR_STREAMID, VITA_ERR_SECS, VITA_ERR_TICS, VITA_ERR_TICS2, VITA_ERR_PAYLOAD :
+       VITA_ERR_HEADER, VITA_ERR_STREAMID, VITA_ERR_TICS, VITA_ERR_TICS2, VITA_ERR_PAYLOAD :
 	 req_write_pkt_fifo <= 1;
        default :
 	 req_write_pkt_fifo <= 0;
diff --git a/fpga/usrp2/vrt/vita_tx_chain.v b/fpga/usrp2/vrt/vita_tx_chain.v
index ac9f08fc8..82a43d57a 100644
--- a/fpga/usrp2/vrt/vita_tx_chain.v
+++ b/fpga/usrp2/vrt/vita_tx_chain.v
@@ -1,5 +1,5 @@
 //
-// Copyright 2011 Ettus Research LLC
+// Copyright 2011-2012 Ettus Research LLC
 //
 // This program is free software: you can redistribute it and/or modify
 // it under the terms of the GNU General Public License as published by
@@ -17,8 +17,9 @@
 
 
 module vita_tx_chain
-  #(parameter BASE_CTRL=0,
-    parameter BASE_DSP=0,
+  #(parameter BASE=0,
+    parameter FIFOSIZE=10,
+    parameter POST_ENGINE_FIFOSIZE=10,
     parameter REPORT_ERROR=0,
     parameter DO_FLOW_CONTROL=0,
     parameter PROT_ENG_FLAGS=0,
@@ -26,11 +27,12 @@ module vita_tx_chain
     parameter DSP_NUMBER=0)
    (input clk, input reset,
     input set_stb, input [7:0] set_addr, input [31:0] set_data,
+    input set_stb_user, input [7:0] set_addr_user, input [31:0] set_data_user,
     input [63:0] vita_time,
     input [35:0] tx_data_i, input tx_src_rdy_i, output tx_dst_rdy_o,
     output [35:0] err_data_o, output err_src_rdy_o, input err_dst_rdy_i,
-    output [23:0] tx_i, output [23:0] tx_q,
-    output underrun, output run,
+    output [31:0] sample, input strobe,
+    output underrun, output run, output clear_o,
     output [31:0] debug);
 
    localparam MAXCHAN = 1;
@@ -38,8 +40,6 @@ module vita_tx_chain
 
    wire [FIFOWIDTH-1:0] tx1_data;
    wire 		tx1_src_rdy, tx1_dst_rdy;
-   wire 		clear_vita;
-   wire [31:0] 		sample_tx;
    wire [31:0] 		streamid, message;
    wire 		trigger, sent;
    wire [31:0] 		debug_vtc, debug_vtd, debug_tx_dsp;
@@ -48,61 +48,104 @@ module vita_tx_chain
    wire [31:0] 		error_code;
    wire 		clear_seqnum;
    wire [31:0] 		current_seqnum;
-   wire 		strobe_tx;
-   
+
+   wire clear, flush;
+   assign clear_o = clear;
    assign underrun = error;
    assign message = error_code;
-   
-   setting_reg #(.my_addr(BASE_CTRL+1)) sr
+
+   setting_reg #(.my_addr(BASE+0), .width(1)) sr
      (.clk(clk),.rst(reset),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out(),.changed(clear_vita));
+      .in(set_data),.out(flush),.changed(clear));
 
-   setting_reg #(.my_addr(BASE_CTRL+2), .at_reset(0)) sr_streamid
+   setting_reg #(.my_addr(BASE+2), .at_reset(0)) sr_streamid
      (.clk(clk),.rst(reset),.strobe(set_stb),.addr(set_addr),
       .in(set_data),.out(streamid),.changed(clear_seqnum));
 
-   vita_tx_deframer #(.BASE(BASE_CTRL), 
+    //flush control - full rate vacuum of input until flush cleared
+    wire tx_dst_rdy_int, tx_src_rdy_int;
+    wire [35:0] tx_data_int;
+    valve36 flusher_valve
+    (.clk(clk), .reset(reset), .clear(clear & flush), .shutoff(flush),
+     .data_i(tx_data_i), .src_rdy_i(tx_src_rdy_i), .dst_rdy_o(tx_dst_rdy_o),
+     .data_o(tx_data_int), .src_rdy_o(tx_src_rdy_int), .dst_rdy_i(tx_dst_rdy_int));
+
+   wire [35:0] tx_data_int1;
+   wire tx_src_rdy_int1, tx_dst_rdy_int1;
+
+    generate
+    if (FIFOSIZE==0) begin
+        assign tx_data_int1 = tx_data_int;
+        assign tx_src_rdy_int1 = tx_src_rdy_int;
+        assign tx_dst_rdy_int = tx_dst_rdy_int1;
+    end
+    else begin
+       wire [FIFOSIZE-1:0] access_adr, access_len;
+       wire 	       access_we, access_stb, access_ok, access_done, access_skip_read;
+       wire [35:0] 	       dsp_to_buf, buf_to_dsp;
+       wire [35:0] tx_data_int0;
+       wire tx_src_rdy_int0, tx_dst_rdy_int0;
+
+       double_buffer #(.BUF_SIZE(FIFOSIZE)) db
+         (.clk(clk),.reset(reset),.clear(clear),
+          .access_we(access_we), .access_stb(access_stb), .access_ok(access_ok), .access_done(access_done),
+          .access_skip_read(access_skip_read), .access_adr(access_adr), .access_len(access_len),
+          .access_dat_i(dsp_to_buf), .access_dat_o(buf_to_dsp),
+
+          .data_i(tx_data_int), .src_rdy_i(tx_src_rdy_int), .dst_rdy_o(tx_dst_rdy_int),
+          .data_o(tx_data_int0), .src_rdy_o(tx_src_rdy_int0), .dst_rdy_i(tx_dst_rdy_int0));
+
+       vita_tx_engine_glue #(.DSPNO(DSP_NUMBER), .MAIN_SETTINGS_BASE(BASE+1), .BUF_SIZE(FIFOSIZE), .HEADER_OFFSET(USE_TRANS_HEADER)) dspengine_tx
+         (.clock(clk),.reset(reset),.clear(clear),
+          .set_stb_main(set_stb), .set_addr_main(set_addr), .set_data_main(set_data),
+          .set_stb_user(set_stb_user), .set_addr_user(set_addr_user), .set_data_user(set_data_user),
+          .access_we(access_we), .access_stb(access_stb), .access_ok(access_ok), .access_done(access_done),
+          .access_skip_read(access_skip_read), .access_adr(access_adr), .access_len(access_len),
+          .access_dat_i(buf_to_dsp), .access_dat_o(dsp_to_buf));
+
+       fifo_cascade #(.WIDTH(36), .SIZE(POST_ENGINE_FIFOSIZE)) post_engine_buffering(
+        .clk(clk), .reset(reset), .clear(clear),
+        .datain(tx_data_int0), .src_rdy_i(tx_src_rdy_int0), .dst_rdy_o(tx_dst_rdy_int0),
+        .dataout(tx_data_int1), .src_rdy_o(tx_src_rdy_int1), .dst_rdy_i(tx_dst_rdy_int1));
+
+    end
+    endgenerate
+
+   vita_tx_deframer #(.BASE(BASE), 
 		      .MAXCHAN(MAXCHAN), 
 		      .USE_TRANS_HEADER(USE_TRANS_HEADER)) 
    vita_tx_deframer
-     (.clk(clk), .reset(reset), .clear(clear_vita), .clear_seqnum(clear_seqnum),
+     (.clk(clk), .reset(reset), .clear(clear), .clear_seqnum(clear_seqnum),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
-      .data_i(tx_data_i), .src_rdy_i(tx_src_rdy_i), .dst_rdy_o(tx_dst_rdy_o),
+      .data_i(tx_data_int1), .src_rdy_i(tx_src_rdy_int1), .dst_rdy_o(tx_dst_rdy_int1),
       .sample_fifo_o(tx1_data), .sample_fifo_src_rdy_o(tx1_src_rdy), .sample_fifo_dst_rdy_i(tx1_dst_rdy),
       .current_seqnum(current_seqnum),
       .debug(debug_vtd) );
 
-   vita_tx_control #(.BASE(BASE_CTRL), .WIDTH(32*MAXCHAN)) vita_tx_control
-     (.clk(clk), .reset(reset), .clear(clear_vita),
+   vita_tx_control #(.BASE(BASE), .WIDTH(32*MAXCHAN)) vita_tx_control
+     (.clk(clk), .reset(reset), .clear(clear),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
       .vita_time(vita_time), .error(error), .ack(ack), .error_code(error_code),
       .sample_fifo_i(tx1_data), .sample_fifo_src_rdy_i(tx1_src_rdy), .sample_fifo_dst_rdy_o(tx1_dst_rdy),
-      .sample(sample_tx), .run(run), .strobe(strobe_tx), .packet_consumed(packet_consumed),
+      .sample(sample), .run(run), .strobe(strobe), .packet_consumed(packet_consumed),
       .debug(debug_vtc) );
-   
-   dsp_core_tx #(.BASE(BASE_DSP)) dsp_core_tx
-     (.clk(clk),.rst(reset),
-      .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
-      .sample(sample_tx), .run(run), .strobe(strobe_tx),
-      .tx_i(tx_i),.tx_q(tx_q),
-      .debug(debug_tx_dsp) );
 
    wire [35:0] 		flow_data, err_data_int;
    wire 		flow_src_rdy, flow_dst_rdy, err_src_rdy_int, err_dst_rdy_int;
    
    gen_context_pkt #(.PROT_ENG_FLAGS(PROT_ENG_FLAGS),.DSP_NUMBER(DSP_NUMBER)) gen_flow_pkt
-     (.clk(clk), .reset(reset), .clear(clear_vita),
+     (.clk(clk), .reset(reset), .clear(clear),
       .trigger(trigger & (DO_FLOW_CONTROL==1)), .sent(), 
       .streamid(streamid), .vita_time(vita_time), .message(32'd0),
       .seqnum(current_seqnum),
       .data_o(flow_data), .src_rdy_o(flow_src_rdy), .dst_rdy_i(flow_dst_rdy));
-   trigger_context_pkt #(.BASE(BASE_CTRL)) trigger_context_pkt
-     (.clk(clk), .reset(reset), .clear(clear_vita),
+   trigger_context_pkt #(.BASE(BASE)) trigger_context_pkt
+     (.clk(clk), .reset(reset), .clear(clear),
       .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
       .packet_consumed(packet_consumed), .trigger(trigger));
    
    gen_context_pkt #(.PROT_ENG_FLAGS(PROT_ENG_FLAGS),.DSP_NUMBER(DSP_NUMBER)) gen_tx_err_pkt
-     (.clk(clk), .reset(reset), .clear(clear_vita),
+     (.clk(clk), .reset(reset), .clear(clear),
       .trigger((error|ack) & (REPORT_ERROR==1)), .sent(), 
       .streamid(streamid), .vita_time(vita_time), .message(message),
       .seqnum(current_seqnum),
diff --git a/fpga/usrp2/vrt/vita_tx_control.v b/fpga/usrp2/vrt/vita_tx_control.v
index 5df89bdbe..c3ce2b96a 100644
--- a/fpga/usrp2/vrt/vita_tx_control.v
+++ b/fpga/usrp2/vrt/vita_tx_control.v
@@ -50,11 +50,9 @@ module vita_tx_control
    
    wire        now, early, late, too_early;
 
-   // FIXME ignore too_early for now for timing reasons
-   assign too_early = 0;
    time_compare 
      time_compare (.time_now(vita_time), .trigger_time(send_time), 
-		   .now(now), .early(early), .late(late), .too_early());
+		   .now(now), .early(early), .late(late), .too_early(too_early));
 
    reg 	       late_qual, late_del;
 
@@ -187,8 +185,17 @@ module vita_tx_control
    
    assign sample_fifo_dst_rdy_o = (ibs_state == IBS_ERROR) | (strobe & (ibs_state == IBS_RUN));  // FIXME also cleanout
 
-   assign sample = (ibs_state == IBS_RUN) ? sample_fifo_i[5+64+16+WIDTH-1:5+64+16] : {WIDTH{1'b0}};
-   //assign run = (ibs_state == IBS_RUN) | (ibs_state == IBS_CONT_BURST);
+   //register the output sample
+   reg [31:0] sample_held;
+   assign sample = sample_held;
+   always @(posedge clk)
+     if(reset | clear)
+        sample_held <= 0;
+     else if (~run)
+       sample_held <= 0;
+     else if (strobe)
+       sample_held <= sample_fifo_i[5+64+16+WIDTH-1:5+64+16];
+
    assign error = send_error;
    assign ack = send_ack;
 
diff --git a/fpga/usrp2/vrt/vita_tx_deframer.v b/fpga/usrp2/vrt/vita_tx_deframer.v
index 06ca27767..6919da11a 100644
--- a/fpga/usrp2/vrt/vita_tx_deframer.v
+++ b/fpga/usrp2/vrt/vita_tx_deframer.v
@@ -1,5 +1,5 @@
 //
-// Copyright 2011 Ettus Research LLC
+// Copyright 2011-2012 Ettus Research LLC
 //
 // This program is free software: you can redistribute it and/or modify
 // it under the terms of the GNU General Public License as published by
@@ -85,7 +85,6 @@ module vita_tx_deframer
    localparam VITA_TICS 	 = 6;
    localparam VITA_TICS2 	 = 7;
    localparam VITA_PAYLOAD 	 = 8;
-   localparam VITA_STORE         = 9;
    localparam VITA_TRAILER 	 = 10;
    localparam VITA_DUMP          = 11;
    
@@ -118,21 +117,7 @@ module vita_tx_deframer
 	    <= 0;
 	  seqnum_err <= 0;
        end
-     else 
-       if((vita_state == VITA_STORE) & fifo_space)
-	 if(vita_eof)  
-	   if(eof)
-	     vita_state <= (USE_TRANS_HEADER==1) ? VITA_TRANS_HEADER : VITA_HEADER;
-	   else if(has_trailer_reg)
-	     vita_state <= VITA_TRAILER;
-	   else
-	     vita_state <= VITA_DUMP;
-   	 else
-	   begin
-	      vita_state <= VITA_PAYLOAD;
-	      pkt_len <= pkt_len - 1;
-	   end
-       else if(src_rdy_i)
+     else if(src_rdy_i & dst_rdy_o) begin //valid read
 	 case(vita_state)
 	   VITA_TRANS_HEADER :
 	     begin
@@ -184,14 +169,33 @@ module vita_tx_deframer
 	     vita_state <= VITA_TICS2;
 	   VITA_TICS2 :
 	     vita_state <= VITA_PAYLOAD;
-	   VITA_PAYLOAD :
-	     if(line_done)
-	       begin
-		  vector_phase <= 0;
-		  vita_state <= VITA_STORE;
-	       end
-	     else
-	       vector_phase <= vector_phase + 1;
+
+        VITA_PAYLOAD : begin
+
+            //step through each element until line done, then reset
+            vector_phase <= (line_done)? 0: vector_phase + 1;
+
+            //decrement the packet count after each line
+            pkt_len <= (line_done)? pkt_len - 1 : pkt_len;
+
+            //end of frame reached, determine next state
+            //otherwise, keep processing through the payload
+            if (line_done && vita_eof) begin
+
+                if (eof) begin
+                    vita_state <= (USE_TRANS_HEADER==1) ? VITA_TRANS_HEADER : VITA_HEADER;
+                end
+                else if (has_trailer_reg) begin
+                    vita_state <= VITA_TRAILER;
+                end
+                else begin
+                    vita_state <= VITA_DUMP;
+                end
+
+            end //line_done && vita_eof
+
+        end //end VITA_PAYLOAD
+
 	   VITA_TRAILER :
 	     if(eof)
 	       vita_state <= (USE_TRANS_HEADER==1) ? VITA_TRANS_HEADER : VITA_HEADER;
@@ -200,46 +204,53 @@ module vita_tx_deframer
 	   VITA_DUMP :
 	     if(eof)
 	       vita_state <= (USE_TRANS_HEADER==1) ? VITA_TRANS_HEADER : VITA_HEADER;
-	   VITA_STORE :
-	     ;
 	   default :
 	     vita_state <= (USE_TRANS_HEADER==1) ? VITA_TRANS_HEADER : VITA_HEADER;
 	 endcase // case (vita_state)
 
-   assign line_done = (vector_phase == numchan);
+     end //valid read
+
+   assign line_done = (MAXCHAN == 1)? 1 : (vector_phase == numchan);
    
    wire [FIFOWIDTH-1:0] fifo_i;
    reg [63:0] 		      send_time;
-   reg [31:0] 		      sample_a, sample_b, sample_c, sample_d;
    
    always @(posedge clk)
      case(vita_state)
-       VITA_SECS :
+       VITA_TICS :
 	 send_time[63:32] <= data_i[31:0];
        VITA_TICS2 :
 	 send_time[31:0] <= data_i[31:0];
      endcase // case (vita_state)
-   
+
+   //sample registers for de-framing a vector input
+   reg [31:0] sample_reg [1:0];
    always @(posedge clk)
-     if(vita_state == VITA_PAYLOAD)
-       case(vector_phase)
-	 0: sample_a <= data_i[31:0];
-	 1: sample_b <= data_i[31:0];
-	 2: sample_c <= data_i[31:0];
-	 3: sample_d <= data_i[31:0];
-       endcase // case (vector_phase)
-   
-   wire 		      store = (vita_state == VITA_STORE);
+     if(src_rdy_i && dst_rdy_o)
+        sample_reg[vector_phase] <= data_i[31:0];
+
+   wire store = (vita_state == VITA_PAYLOAD)? (src_rdy_i && line_done) : 0;
+   assign dst_rdy_o = (vita_state == VITA_PAYLOAD)? fifo_space : 1;
+
    fifo_short #(.WIDTH(FIFOWIDTH)) short_tx_q
      (.clk(clk), .reset(reset), .clear(clear),
       .datain(fifo_i), .src_rdy_i(store), .dst_rdy_o(fifo_space),
       .dataout(sample_fifo_o), .src_rdy_o(sample_fifo_src_rdy_o), .dst_rdy_i(sample_fifo_dst_rdy_i) );
 
-   // sob, eob, has_secs (send_at) ignored on all lines except first
-   assign fifo_i = {sample_d,sample_c,sample_b,sample_a,seqnum_err,has_secs_reg,is_sob_reg,is_eob_reg,eop,
-		    12'd0,seqnum_reg[3:0],send_time};
+    //assign registered/live data to the samples vector
+    //the numchan'th sample vector is muxed to live data
+    wire [(32*MAXCHAN)-1:0] samples;
+    generate
+    genvar i;
+    for (i=0; i < MAXCHAN; i = i +1) begin : assign_samples
+        wire live_data = (i == (MAXCHAN-1))? 1 : numchan == i;
+        assign samples[32*i + 31:32*i] = (live_data)? data_i[31:0] : sample_reg[i];
+    end
+    endgenerate
 
-   assign dst_rdy_o = ~(vita_state == VITA_PAYLOAD) & ~((vita_state==VITA_STORE)& ~fifo_space) ;
+   // sob, eob, has_tics (send_at) ignored on all lines except first
+   assign fifo_i = {samples,seqnum_err,has_tics_reg,is_sob_reg,is_eob_reg,eop,
+		    12'd0,seqnum_reg[3:0],send_time};
 
    assign debug = { { 8'b0 },
 		    { 8'b0 },
diff --git a/fpga/usrp2/vrt/vita_tx_engine_glue.v b/fpga/usrp2/vrt/vita_tx_engine_glue.v
new file mode 100644
index 000000000..db0d55dee
--- /dev/null
+++ b/fpga/usrp2/vrt/vita_tx_engine_glue.v
@@ -0,0 +1,99 @@
+//
+// Copyright 2012 Ettus Research LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+//The following module is used to re-write transmit packets from the host.
+//This module provides a packet-based ram interface for manipulating packets.
+//By default, this module uses the built-in 8 to 16 bit converter engine.
+
+module vita_tx_engine_glue
+#(
+    //the dsp unit number: 0, 1, 2...
+    parameter DSPNO = 0,
+
+    //buffer size for ram interface engine
+    parameter BUF_SIZE = 10,
+
+    //base address for built-in settings registers used in this module
+    parameter MAIN_SETTINGS_BASE = 0,
+
+    //the number of 32bit lines between start of buffer and vita header
+    //the metadata before the header should be preserved by the engine
+    parameter HEADER_OFFSET = 0
+)
+(
+    //control signals
+    input clock, input reset, input clear,
+
+    //main settings bus for built-in modules
+    input set_stb_main, input [7:0] set_addr_main, input [31:0] set_data_main,
+
+    //user settings bus, controlled through user setting regs API
+    input set_stb_user, input [7:0] set_addr_user, input [31:0] set_data_user,
+
+    //ram interface for engine
+    output access_we,
+    output access_stb,
+    input access_ok,
+    output access_done,
+    output access_skip_read,
+    output [BUF_SIZE-1:0] access_adr,
+    input [BUF_SIZE-1:0] access_len,
+    output [35:0] access_dat_o,
+    input [35:0] access_dat_i,
+
+    //debug output (optional)
+    output [31:0] debug
+);
+
+    generate
+        if (DSPNO==0) begin
+            `ifndef TX_ENG0_MODULE
+            dspengine_8to16 #(.BASE(MAIN_SETTINGS_BASE), .BUF_SIZE(BUF_SIZE), .HEADER_OFFSET(HEADER_OFFSET)) dspengine_8to16
+             (.clk(clock),.reset(reset),.clear(clear),
+              .set_stb(set_stb_main), .set_addr(set_addr_main), .set_data(set_data_main),
+              .access_we(access_we), .access_stb(access_stb), .access_ok(access_ok), .access_done(access_done), 
+              .access_skip_read(access_skip_read), .access_adr(access_adr), .access_len(access_len), 
+              .access_dat_i(access_dat_i), .access_dat_o(access_dat_o));
+            `else
+            `TX_ENG0_MODULE #(.BUF_SIZE(BUF_SIZE), .HEADER_OFFSET(HEADER_OFFSET)) tx_eng0_custom
+             (.clock(clock),.reset(reset),.clear(clear),
+              .set_stb(set_stb_user), .set_addr(set_addr_user), .set_data(set_data_user),
+              .access_we(access_we), .access_stb(access_stb), .access_ok(access_ok), .access_done(access_done), 
+              .access_skip_read(access_skip_read), .access_adr(access_adr), .access_len(access_len), 
+              .access_dat_i(access_dat_i), .access_dat_o(access_dat_o));
+            `endif
+        end
+        else begin
+            `ifndef TX_ENG1_MODULE
+            dspengine_8to16 #(.BASE(MAIN_SETTINGS_BASE), .BUF_SIZE(BUF_SIZE), .HEADER_OFFSET(HEADER_OFFSET)) dspengine_8to16
+             (.clk(clock),.reset(reset),.clear(clear),
+              .set_stb(set_stb_main), .set_addr(set_addr_main), .set_data(set_data_main),
+              .access_we(access_we), .access_stb(access_stb), .access_ok(access_ok), .access_done(access_done), 
+              .access_skip_read(access_skip_read), .access_adr(access_adr), .access_len(access_len), 
+              .access_dat_i(access_dat_i), .access_dat_o(access_dat_o));
+            `else
+            `TX_ENG1_MODULE #(.BUF_SIZE(BUF_SIZE), .HEADER_OFFSET(HEADER_OFFSET)) tx_eng1_custom
+             (.clock(clock),.reset(reset),.clear(clear),
+              .set_stb(set_stb_user), .set_addr(set_addr_user), .set_data(set_data_user),
+              .access_we(access_we), .access_stb(access_stb), .access_ok(access_ok), .access_done(access_done), 
+              .access_skip_read(access_skip_read), .access_adr(access_adr), .access_len(access_len), 
+              .access_dat_i(access_dat_i), .access_dat_o(access_dat_o));
+            `endif
+        end
+    endgenerate
+
+endmodule //vita_tx_engine_glue