Merge branch 'atr_fix_fpga' into atr_fixrelease_003_002_000

1 files changed, 16 insertions, 16 deletions

diff --git a/fpga/usrp2/top/USRP2/u2_core.v b/fpga/usrp2/top/USRP2/u2_core.v
index 2e3d41731..ee1116eac 100644
--- a/fpga/usrp2/top/USRP2/u2_core.v
+++ b/fpga/usrp2/top/USRP2/u2_core.v
@@ -193,7 +193,6 @@ module u2_core
    wire 	uart_tx_int, uart_rx_int;
 
    wire [31:0] 	debug_gpio_0, debug_gpio_1;
-   wire [31:0] 	atr_lines;
 
    wire [31:0] 	debug_rx, debug_mac, debug_mac0, debug_mac1, debug_tx_dsp, debug_txc,
 		debug_serdes0, debug_serdes1, debug_serdes2, debug_rx_dsp, debug_udp, debug_extfifo, debug_extfifo2;
@@ -202,7 +201,7 @@ module u2_core
    wire 	ser_rx_full, ser_tx_full, dsp_rx_full, dsp_tx_full, eth_rx_full, eth_tx_full, eth_rx_full2;
    wire 	ser_rx_empty, ser_tx_empty, dsp_rx_empty, dsp_tx_empty, eth_rx_empty, eth_tx_empty, eth_rx_empty2;
 	
-   wire 	serdes_link_up;
+   wire 	serdes_link_up, good_sync;
    wire 	epoch;
    wire [31:0] 	irq;
    wire [63:0] 	vita_time, vita_time_pps;
@@ -423,17 +422,17 @@ module u2_core
    
    // /////////////////////////////////////////////////////////////////////////
    // GPIOs -- Slave #4
+
    nsgpio nsgpio(.clk_i(wb_clk),.rst_i(wb_rst),
-		 .cyc_i(s4_cyc),.stb_i(s4_stb),.adr_i(s4_adr[3:0]),.we_i(s4_we),
+		 .cyc_i(s4_cyc),.stb_i(s4_stb),.adr_i(s4_adr[4:0]),.we_i(s4_we),
 		 .dat_i(s4_dat_o),.dat_o(s4_dat_i),.ack_o(s4_ack),
-		 .atr(atr_lines),.debug_0(debug_gpio_0),.debug_1(debug_gpio_1),
-		 .gpio({io_tx,io_rx}) );
+		 .rx(run_rx0_d1 | rx_rx1_d1), .tx(run_tx), .gpio({io_tx,io_rx}) );
 
    // /////////////////////////////////////////////////////////////////////////
    // Buffer Pool Status -- Slave #5   
    
    //compatibility number -> increment when the fpga has been sufficiently altered
-   localparam compat_num = {16'd7, 16'd0}; //major, minor
+   localparam compat_num = {16'd7, 16'd1}; //major, minor
 
    wb_readback_mux buff_pool_status
      (.wb_clk_i(wb_clk), .wb_rst_i(wb_rst), .wb_stb_i(s5_stb),
@@ -441,7 +440,7 @@ module u2_core
 
       .word00(32'b0),.word01(32'b0),.word02(32'b0),.word03(32'b0),
       .word04(32'b0),.word05(32'b0),.word06(32'b0),.word07(32'b0),
-      .word08(status),.word09({sim_mode,27'b0,clock_divider[3:0]}),.word10(vita_time[63:32]),
+      .word08(status),.word09(32'b0),.word10(vita_time[63:32]),
       .word11(vita_time[31:0]),.word12(compat_num),.word13(irq),
       .word14(vita_time_pps[63:32]),.word15(vita_time_pps[31:0])
       );
@@ -502,7 +501,7 @@ module u2_core
    //    In Rev3 there are only 6 leds, and the highest one is on the ETH connector
    
    wire [7:0] 	 led_src, led_sw;
-   wire [7:0] 	 led_hw = {run_tx, (run_rx0_d1 | run_rx1_d1), clk_status, serdes_link_up, 1'b0};
+   wire [7:0] 	 led_hw = {run_tx, (run_rx0_d1 | run_rx1_d1), clk_status, serdes_link_up & good_sync, 1'b0};
    
    setting_reg #(.my_addr(SR_MISC+3),.width(8)) sr_led (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
 				      .in(set_data),.out(led_sw),.changed());
@@ -524,7 +523,7 @@ module u2_core
    
    assign irq= {{8'b0},
 		{8'b0},
-		{3'b0, periodic_int, clk_status, serdes_link_up, uart_tx_int, uart_rx_int},
+		{2'b0, good_sync, periodic_int, clk_status, serdes_link_up, uart_tx_int, uart_rx_int},
 		{pps_wb,overrun_wb,underrun_wb,PHY_INTn,i2c_int,spi_int,onetime_int,buffer_int}};
    
    pic pic(.clk_i(wb_clk),.rst_i(wb_rst),.cyc_i(s8_cyc),.stb_i(s8_stb),.adr_i(s8_adr[4:2]),
@@ -539,12 +538,12 @@ module u2_core
    
    // /////////////////////////////////////////////////////////////////////////
    //  Simple Timer interrupts
-   
+   /*
    simple_timer #(.BASE(SR_SIMTIMER)) simple_timer
      (.clk(wb_clk), .reset(wb_rst),
       .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
       .onetime_int(onetime_int), .periodic_int(periodic_int));
-   
+   */
    // /////////////////////////////////////////////////////////////////////////
    // UART, Slave #10
 
@@ -558,11 +557,13 @@ module u2_core
    // /////////////////////////////////////////////////////////////////////////
    // ATR Controller, Slave #11
 
+   /*
    atr_controller atr_controller
      (.clk_i(wb_clk),.rst_i(wb_rst),
       .adr_i(sb_adr[5:0]),.sel_i(sb_sel),.dat_i(sb_dat_o),.dat_o(sb_dat_i),
       .we_i(sb_we),.stb_i(sb_stb),.cyc_i(sb_cyc),.ack_o(sb_ack),
       .run_rx(run_rx0_d1 | run_rx1_d1),.run_tx(run_tx),.ctrl_lines(atr_lines) );
+   */
    
    // //////////////////////////////////////////////////////////////////////////
    // Time Sync, Slave #12 
@@ -572,16 +573,16 @@ module u2_core
    
    // /////////////////////////////////////////////////////////////////////////
    // SD Card Reader / Writer, Slave #13
-
+   /*
    sd_spi_wb sd_spi_wb
      (.clk(wb_clk),.rst(wb_rst),
       .sd_clk(sd_clk),.sd_csn(sd_csn),.sd_mosi(sd_mosi),.sd_miso(sd_miso),
       .wb_cyc_i(sd_cyc),.wb_stb_i(sd_stb),.wb_we_i(sd_we),
       .wb_adr_i(sd_adr[3:2]),.wb_dat_i(sd_dat_o[7:0]),.wb_dat_o(sd_dat_i[7:0]),
       .wb_ack_o(sd_ack) );
-
+    
    assign sd_dat_i[31:8] = 0;
-
+    */
    // /////////////////////////////////////////////////////////////////////////
    // ADC Frontend
    wire [23:0] 	 adc_i, adc_q;
@@ -729,8 +730,7 @@ module u2_core
    time_64bit #(.TICKS_PER_SEC(32'd100000000),.BASE(SR_TIME64)) time_64bit
      (.clk(dsp_clk), .rst(dsp_rst), .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
       .pps(pps_in), .vita_time(vita_time), .vita_time_pps(vita_time_pps), .pps_int(pps_int),
-      .exp_time_in(exp_time_in), .exp_time_out(exp_time_out),
-      .debug(debug_sync));
+      .exp_time_in(exp_time_in), .exp_time_out(exp_time_out), .good_sync(good_sync), .debug(debug_sync));
 
    // /////////////////////////////////////////////////////////////////////////////////////////
    // Debug Pins