Merged r9433:9527 from features/gr-usrp2 into trunk. Adds usrp2 and gr-usrp2 top-level components. Trunk passes distcheck with mb-gcc installed, but currently not without them. The key issue is that when mb-gcc is not installed, the build system skips over the usrp2/firmware directory, and the firmware include files don't get put into the dist tarball. But we can't do the usual DIST_SUBDIRS method as the firmware is a subpackage.

git-svn-id: http://gnuradio.org/svn/gnuradio/trunk@9528 221aa14e-8319-0410-a670-987f0aec2ac5

1 files changed, 84 insertions, 0 deletions

diff --git a/control_lib/spi.v b/control_lib/spi.v
new file mode 100644
index 000000000..a80c488e9
--- /dev/null
+++ b/control_lib/spi.v
@@ -0,0 +1,84 @@
+
+
+// AD9510 Register Map (from datasheet Rev. A)
+
+/* INSTRUCTION word format (16 bits)
+ * 15       Read = 1, Write = 0
+ * 14:13    W1/W0,  Number of bytes 00 - 1, 01 - 2, 10 - 3, 11 - stream
+ * 12:0     Address
+ */
+
+/* ADDR     Contents             Value (hex)
+ * 00       Serial Config Port   10 (def) -- MSB first, SDI/SDO separate
+ * 04       A Counter
+ * 05-06    B Counter
+ * 07-0A    PLL Control
+ * 0B-0C    R Divider
+ * 0D       PLL Control
+ * 34-3A    Fine Delay
+ * 3C-3F    LVPECL Outs
+ * 40-43    LVDS/CMOS Outs
+ * 45       Clock select, power down
+ * 48-57    Dividers
+ * 58       Func and Sync
+ * 5A       Update regs
+ */
+
+
+module spi
+  (input reset,
+   input clk,
+
+   // SPI signals
+   output sen, 
+   output sclk,
+   input sdi,
+   output sdo,
+
+   // Interfaces
+   input read_1,
+   input write_1,
+   input [15:0] command_1,
+   input [15:0] wdata_1,
+   output [15:0] rdata_1,
+   output reg done_1,
+   input msb_first_1,
+   input [5:0] command_width_1,
+   input [5:0] data_width_1,
+   input [7:0] clkdiv_1
+   
+   );
+
+   reg [15:0]  command, wdata, rdata;
+   reg 	       done;
+
+   always @(posedge clk)
+     if(reset)
+       done_1 <= #1 1'b0;
+   
+   always @(posedge clk)
+     if(reset)
+       begin
+	  counter <= #1 7'd0;
+	  command <= #1 20'd0;
+       end
+     else if(start)
+       begin
+	  counter <= #1 7'd1;
+	  command <= #1 {read,w,addr_data};
+       end
+     else if( |counter && ~done )
+       begin
+	  counter <= #1 counter + 7'd1;
+	  if(~counter[0])
+	    command <= {command[22:0],1'b0};
+       end
+
+   wire done = (counter == 8'd49);
+   
+   assign sen = (done | counter == 8'd0);  // CSB is high when we're not doing anything
+   assign sclk = ~counter[0];
+   assign sdo = command[23];
+   
+
+endmodule // clock_control