Merged r6766:6775 from jcorgan/t195. Fixes ticket:195. NOTE: this removes 8 bit sample width support on receive. Synthesized with 7.1SP1.

git-svn-id: http://gnuradio.org/svn/gnuradio/trunk@6776 221aa14e-8319-0410-a670-987f0aec2ac5

6 files changed, 151 insertions, 97 deletions

diff --git a/rbf/rev2/std_2rxhb_2tx.rbf b/rbf/rev2/std_2rxhb_2tx.rbf
index 32c931b52..072bd8dde 100755
--- a/rbf/rev2/std_2rxhb_2tx.rbf
+++ b/rbf/rev2/std_2rxhb_2tx.rbf
diff --git a/rbf/rev2/std_4rx_0tx.rbf b/rbf/rev2/std_4rx_0tx.rbf
index 88573ebe6..43f901d31 100755
--- a/rbf/rev2/std_4rx_0tx.rbf
+++ b/rbf/rev2/std_4rx_0tx.rbf
diff --git a/rbf/rev4/std_2rxhb_2tx.rbf b/rbf/rev4/std_2rxhb_2tx.rbf
index 32c931b52..072bd8dde 100755
--- a/rbf/rev4/std_2rxhb_2tx.rbf
+++ b/rbf/rev4/std_2rxhb_2tx.rbf
diff --git a/rbf/rev4/std_4rx_0tx.rbf b/rbf/rev4/std_4rx_0tx.rbf
index 88573ebe6..43f901d31 100755
--- a/rbf/rev4/std_4rx_0tx.rbf
+++ b/rbf/rev4/std_4rx_0tx.rbf
diff --git a/sdr_lib/rx_buffer.v b/sdr_lib/rx_buffer.v
index ec5b8eefe..7c52925c9 100644
--- a/sdr_lib/rx_buffer.v
+++ b/sdr_lib/rx_buffer.v
@@ -20,21 +20,24 @@
 //
 
 // Interface to Cypress FX2 bus
-// A packet is 512 Bytes.  Each fifo line is 2 bytes
-// Fifo has 1024 or 2048 lines
+// A packet is 512 Bytes, the fifo has 4096 lines of 18 bits each
 
 `include "../../firmware/include/fpga_regs_common.v"
 `include "../../firmware/include/fpga_regs_standard.v"
 
 module rx_buffer
-  ( input usbclk,
-    input bus_reset,  // Not used in RX
-    input reset,  // DSP side reset (used here), do not reset registers
-    input reset_regs, //Only reset registers
+  ( // Read/USB side
+    input usbclk,
+    input bus_reset,
     output [15:0] usbdata,
     input RD,
-    output wire have_pkt_rdy,
+    output reg have_pkt_rdy,
     output reg rx_overrun,
+    input clear_status,
+    // Write/DSP side
+    input rxclk,
+    input reset,  // DSP side reset (used here), do not reset registers
+    input rxstrobe,
     input wire [3:0] channels,
     input wire [15:0] ch_0,
     input wire [15:0] ch_1,
@@ -44,139 +47,191 @@ module rx_buffer
     input wire [15:0] ch_5,
     input wire [15:0] ch_6,
     input wire [15:0] ch_7,
-    input rxclk,
-    input rxstrobe,
-    input clear_status,
+    // Settings, on rxclk also
     input [6:0] serial_addr, input [31:0] serial_data, input serial_strobe,
-    output [15:0] debugbus
+    input reset_regs, //Only reset registers
+    output [31:0] debugbus
     );
-
-   wire [15:0] fifodata, fifodata_8;
-   reg [15:0]  fifodata_16;
    
-   wire [11:0] rxfifolevel;
-   wire rx_empty, rx_full;
-
-   wire bypass_hb, want_q;
-   wire [4:0] bitwidth;
-   wire [3:0] bitshift;
+   wire [15:0] 	  fifodata, fifodata_8;
+   reg [15:0] 	  fifodata_16;
+   
+   wire [11:0] 	  rxfifolevel;
+   wire 	  rx_full;
+   
+   wire 	  bypass_hb, want_q;
+   wire [4:0] 	  bitwidth;
+   wire [3:0] 	  bitshift;
    
    setting_reg #(`FR_RX_FORMAT) sr_rxformat(.clock(rxclk),.reset(reset_regs),
 					    .strobe(serial_strobe),.addr(serial_addr),.in(serial_data),
 					    .out({bypass_hb,want_q,bitwidth,bitshift}));
 
-   // Receive FIFO (ADC --> USB)
+   // USB Read Side of FIFO
+   always @(negedge usbclk)
+     have_pkt_rdy <= (rxfifolevel >= 256);
 
    // 257 Bug Fix
-   reg [8:0] read_count;
+   reg [8:0] 	  read_count;
    always @(negedge usbclk)
      if(bus_reset)
-       read_count <= #1 9'd0;
-     else if(RD & ~read_count[8])
-       read_count <= #1 read_count + 9'd1;
+       read_count <= 0;
+     else if(RD)
+       read_count <= read_count + 1;
      else
-       read_count <= #1 RD ? read_count : 9'b0;
+       read_count <= 0;
    
-   // Detect overrun
+   // FIFO
+   wire 	  ch0_in, ch0_out, iq_out;
+   assign 	  ch0_in = (phase == 1);
+
+   fifo_4k_18 rxfifo 
+     ( // DSP Write Side
+       .data ( {ch0_in, phase[0], fifodata} ),
+       .wrreq (~rx_full & (phase != 0)),
+       .wrclk ( rxclk ),
+       .wrfull ( rx_full ),
+       .wrempty ( ),
+       .wrusedw ( ),
+       // USB Read Side
+       .q ( {ch0_out,iq_out,usbdata} ),
+       .rdreq ( RD & ~read_count[8] ), 
+       .rdclk ( ~usbclk ),
+       .rdfull ( ),
+       .rdempty ( ),
+       .rdusedw ( rxfifolevel ),
+       // Async, shared
+       .aclr ( reset ) );
+
+   // DSP Write Side of FIFO
+   reg [15:0] ch_0_reg;
+   reg [15:0] ch_1_reg;
+   reg [15:0] ch_2_reg;
+   reg [15:0] ch_3_reg;
+   reg [15:0] ch_4_reg;
+   reg [15:0] ch_5_reg;
+   reg [15:0] ch_6_reg;
+   reg [15:0] ch_7_reg;
+
    always @(posedge rxclk)
-     if(reset)
-       rx_overrun <= 1'b0;
-     else if(rxstrobe & (store_next != 0))
-       rx_overrun <= 1'b1;
-     else if(clear_status)
-       rx_overrun <= 1'b0;
+     if (rxstrobe)
+       begin
+         ch_0_reg <= ch_0;
+         ch_1_reg <= ch_1;
+         ch_2_reg <= ch_2;
+         ch_3_reg <= ch_3;
+         ch_4_reg <= ch_4;
+         ch_5_reg <= ch_5;
+         ch_6_reg <= ch_6;
+         ch_7_reg <= ch_7;
+       end
 
-   reg [3:0] store_next;
+   reg [3:0] phase;
    always @(posedge rxclk)
      if(reset)
-       store_next <= #1 4'd0;
-     else if(rxstrobe & (store_next == 0))
-       store_next <= #1 4'd1;
-     else if(~rx_full & (store_next == channels))
-       store_next <= #1 4'd0;
-     else if(~rx_full & (bitwidth == 5'd8) & (store_next == (channels>>1)))
-       store_next <= #1 4'd0;
-     else if(~rx_full & (store_next != 0))
-       store_next <= #1 store_next + 4'd1;
-
+       phase <= 4'd0;
+     else if(phase == 0)
+       begin
+	  if(rxstrobe)
+	    phase <= 4'd1;
+       end
+     else if(~rx_full)
+       if(phase == channels)
+	 phase <= 4'd0;
+       else
+	 phase <= phase + 4'd1;
+   
    assign    fifodata = (bitwidth == 5'd8) ? fifodata_8 : fifodata_16;
-
+   
    assign    fifodata_8 = {round_8(top),round_8(bottom)};
    reg [15:0] top,bottom;
-
+   
    function [7:0] round_8;
       input [15:0] in_val;
-
+      
       round_8 = in_val[15:8] + (in_val[15] & |in_val[7:0]);
    endfunction // round_8
       
    always @*
-     case(store_next)
+     case(phase)
        4'd1 : begin
-	  bottom = ch_0;
-	  top = ch_1;
+	  bottom = ch_0_reg;
+	  top = ch_1_reg;
        end
        4'd2 : begin
-	  bottom = ch_2;
-	  top = ch_3;
+	  bottom = ch_2_reg;
+	  top = ch_3_reg;
        end
        4'd3 : begin
-	  bottom = ch_4;
-	  top = ch_5;
+	  bottom = ch_4_reg;
+	  top = ch_5_reg;
        end
        4'd4 : begin
-	  bottom = ch_6;
-	  top = ch_7;
+	  bottom = ch_6_reg;
+	  top = ch_7_reg;
        end
        default : begin
 	  top = 16'hFFFF;
 	  bottom = 16'hFFFF;
        end
-     endcase // case(store_next)
+     endcase // case(phase)
    
    always @*
-     case(store_next)
-       4'd1 : fifodata_16 = ch_0;
-       4'd2 : fifodata_16 = ch_1;
-       4'd3 : fifodata_16 = ch_2;
-       4'd4 : fifodata_16 = ch_3;
-       4'd5 : fifodata_16 = ch_4;
-       4'd6 : fifodata_16 = ch_5;
-       4'd7 : fifodata_16 = ch_6;
-       4'd8 : fifodata_16 = ch_7;
+     case(phase)
+       4'd1 : fifodata_16 = ch_0_reg;
+       4'd2 : fifodata_16 = ch_1_reg;
+       4'd3 : fifodata_16 = ch_2_reg;
+       4'd4 : fifodata_16 = ch_3_reg;
+       4'd5 : fifodata_16 = ch_4_reg;
+       4'd6 : fifodata_16 = ch_5_reg;
+       4'd7 : fifodata_16 = ch_6_reg;
+       4'd8 : fifodata_16 = ch_7_reg;
        default : fifodata_16 = 16'hFFFF;
-     endcase // case(store_next)
+     endcase // case(phase)
    
-   fifo_4k rxfifo 
-     ( .data ( fifodata ),
-       .wrreq (~rx_full & (store_next != 0)),
-       .wrclk ( rxclk ),
+   // Detect overrun
+   reg clear_status_dsp, rx_overrun_dsp;
+   always @(posedge rxclk)
+     clear_status_dsp <= clear_status;
 
-       .q ( usbdata ),
-       .rdreq ( RD & ~read_count[8] ), 
-       .rdclk ( ~usbclk ),
-       
-       .aclr ( reset ),  // This one is asynchronous, so we can use either reset
-       
-       .rdempty ( rx_empty ),
-       .rdusedw ( rxfifolevel ),
-       .wrfull ( rx_full ),
-       .wrusedw (  )
-       );
+   always @(negedge usbclk)
+     rx_overrun <= rx_overrun_dsp;
+
+   always @(posedge rxclk)
+     if(reset)
+       rx_overrun_dsp <= 1'b0;
+     else if(rxstrobe & (phase != 0))
+       rx_overrun_dsp <= 1'b1;
+     else if(clear_status_dsp)
+       rx_overrun_dsp <= 1'b0;
+
+   // Debug bus
+   //
+   // 15:0  rxclk  domain => TXA 15:0
+   // 31:16 usbclk domain => RXA 15:0
    
-   assign have_pkt_rdy = (rxfifolevel >= 256);
+   assign debugbus[0]     = reset;
+   assign debugbus[1]     = reset_regs;
+   assign debugbus[2]     = rxstrobe;
+   assign debugbus[6:3]   = channels;
+   assign debugbus[7]     = rx_full;
+   assign debugbus[11:8]  = phase;
+   assign debugbus[12]    = ch0_in;
+   assign debugbus[13]    = clear_status_dsp;
+   assign debugbus[14]    = rx_overrun_dsp;
+   assign debugbus[15]    = rxclk;
 
-   // Debugging Aids
-   assign debugbus[0] = RD;
-   assign debugbus[1] = rx_overrun;
-   assign debugbus[2] = read_count[8];
-   assign debugbus[3] = rx_full;
-   assign debugbus[4] = rxstrobe;
-   assign debugbus[5] = usbclk;
-   assign debugbus[6] = have_pkt_rdy;
-   assign debugbus[10:7] = store_next;
-   //assign debugbus[15:11] = rxfifolevel[4:0];
-   assign debugbus[15:11] = bitwidth;
+   assign debugbus[16]    = bus_reset;   
+   assign debugbus[17]    = RD;
+   assign debugbus[18]    = have_pkt_rdy;
+   assign debugbus[19]    = rx_overrun;
+   assign debugbus[20]    = read_count[0];
+   assign debugbus[21]    = read_count[8];
+   assign debugbus[22]    = ch0_out;
+   assign debugbus[23]    = iq_out;
+   assign debugbus[24]    = clear_status;
+   assign debugbus[30:25] = 0;   
+   assign debugbus[31]    = usbclk;
    
 endmodule // rx_buffer
 
diff --git a/toplevel/usrp_std/usrp_std.v b/toplevel/usrp_std/usrp_std.v
index 4b92cfb16..8b29a9c21 100644
--- a/toplevel/usrp_std/usrp_std.v
+++ b/toplevel/usrp_std/usrp_std.v
@@ -93,8 +93,7 @@ module usrp_std
    wire [2:0]  tx_numchan;
    
    wire [7:0]  interp_rate, decim_rate;
-   wire [15:0] rx_debugbus;
-   wire [31:0] tx_debugbus;
+   wire [31:0] tx_debugbus, rx_debugbus;
    
    wire        enable_tx, enable_rx;
    wire        tx_dsp_reset, rx_dsp_reset, tx_bus_reset, rx_bus_reset;
@@ -318,7 +317,7 @@ module usrp_std
        .tx_empty(tx_empty),
        //.debug_0(rx_a_a),.debug_1(ddc0_in_i),
        .debug_0(tx_debugbus[15:0]),.debug_1(tx_debugbus[31:16]),
-       .debug_2({rx_sample_strobe,strobe_decim,serial_strobe,serial_addr}),.debug_3({rx_dsp_reset,tx_dsp_reset,rx_bus_reset,tx_bus_reset,enable_rx,tx_underrun,rx_overrun,decim_rate}),
+       .debug_2(rx_debugbus[15:0]),.debug_3(rx_debugbus[31:16]),
        .reg_0(reg_0),.reg_1(reg_1),.reg_2(reg_2),.reg_3(reg_3) );
    
    io_pins io_pins