Merge branch 'fpga_ise12'

12 files changed, 399 insertions, 1160 deletions

diff --git a/fpga/usrp2/timing/time_64bit.v b/fpga/usrp2/timing/time_64bit.v
index 51c006962..33eb2b25a 100644
--- a/fpga/usrp2/timing/time_64bit.v
+++ b/fpga/usrp2/timing/time_64bit.v
@@ -3,27 +3,41 @@
 module time_64bit
   #(parameter TICKS_PER_SEC = 32'd100000000,
     parameter BASE = 0)
-    (input clk, input rst,
-     input set_stb, input [7:0] set_addr, input [31:0] set_data,  
-     input pps,
-     output [63:0] vita_time, output pps_int
-     );
-
+   (input clk, input rst,
+    input set_stb, input [7:0] set_addr, input [31:0] set_data,  
+    input pps,
+    output [63:0] vita_time, output pps_int,
+    input exp_time_in, output exp_time_out,
+    output [31:0] debug
+    );
+   
    localparam 	   NEXT_SECS = 0;   
    localparam 	   NEXT_TICKS = 1;
    localparam      PPS_POLSRC = 2;
    localparam      PPS_IMM = 3;
    localparam      TPS = 4;
+   localparam      MIMO_SYNC = 5;
    
    reg [31:0] 	   seconds, ticks;
    wire 	   end_of_second;
    assign 	   vita_time = {seconds,ticks};
+   wire [63:0] 	   vita_time_rcvd;
    
    wire [31:0] 	   next_ticks_preset, next_seconds_preset;
    wire [31:0] 	   ticks_per_sec_reg;
    wire 	   set_on_pps_trig;
    reg 		   set_on_next_pps;
    wire 	   pps_polarity, pps_source, set_imm;
+   reg [1:0] 	   pps_del;
+   reg 		   pps_reg_p, pps_reg_n, pps_reg;
+   wire 	   pps_edge;
+
+   reg [15:0] 	   sync_counter;
+   wire 	   sync_rcvd;
+   wire [31:0] 	   mimo_secs, mimo_ticks;
+   wire 	   mimo_sync_now;
+   wire 	   mimo_sync;
+   wire [7:0] 	   sync_delay;
    
    setting_reg #(.my_addr(BASE+NEXT_TICKS)) sr_next_ticks
      (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
@@ -45,10 +59,10 @@ module time_64bit
      (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
       .in(set_data),.out(ticks_per_sec_reg),.changed());
 
-   reg [1:0] 	   pps_del;
-   reg 		   pps_reg_p, pps_reg_n, pps_reg;
-   wire 	   pps_edge;
-   
+   setting_reg #(.my_addr(BASE+MIMO_SYNC), .at_reset(0), .width(9)) sr_mimosync
+     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
+      .in(set_data),.out({mimo_sync,sync_delay}),.changed());
+
    always @(posedge clk)  pps_reg_p <= pps;   
    always @(negedge clk)  pps_reg_n <= pps;
    always @* pps_reg <= pps_polarity ? pps_reg_p : pps_reg_n;
@@ -82,6 +96,11 @@ module time_64bit
 	  seconds <= next_seconds_preset;
 	  ticks <= next_ticks_preset;
        end
+     else if(mimo_sync_now)
+       begin
+	  seconds <= mimo_secs;
+	  ticks <= mimo_ticks;
+       end
      else if(ticks_plus_one == ticks_per_sec_reg)
        begin
 	  seconds <= seconds + 1;
@@ -91,5 +110,36 @@ module time_64bit
        ticks <= ticks_plus_one;
 
    assign pps_int = pps_edge;
+
+   // MIMO Connector Time Sync
+   wire send_sync = (sync_counter == 59999); // X % 10 = 9
+
+   always @(posedge clk)
+     if(rst)
+       sync_counter <= 0;
+     else
+       if(send_sync)
+	 sync_counter <= 0;
+       else
+	 sync_counter <= sync_counter + 1;
+   
+   time_sender time_sender
+     (.clk(clk),.rst(rst),
+      .vita_time(vita_time),
+      .send_sync(send_sync),
+      .exp_time_out(exp_time_out) );
+
+   time_receiver time_receiver
+     (.clk(clk),.rst(rst),
+      .vita_time(vita_time_rcvd),
+      .sync_rcvd(sync_rcvd),
+      .exp_time_in(exp_time_in) );
+
+   assign mimo_secs = vita_time_rcvd[63:32];
+   assign mimo_ticks = vita_time_rcvd[31:0] + {16'd0,sync_delay};
+   assign mimo_sync_now = mimo_sync & sync_rcvd & (mimo_ticks <= TICKS_PER_SEC);
+
+   assign debug = { { 24'b0} ,
+		    { 2'b0, exp_time_in, exp_time_out, mimo_sync, mimo_sync_now, sync_rcvd, send_sync} };
    
 endmodule // time_64bit
diff --git a/fpga/usrp2/timing/time_receiver.v b/fpga/usrp2/timing/time_receiver.v
index 8e7d3f1ea..fd8651d29 100644
--- a/fpga/usrp2/timing/time_receiver.v
+++ b/fpga/usrp2/timing/time_receiver.v
@@ -1,9 +1,9 @@
 
 module time_receiver
   (input clk, input rst,
-   output [31:0] master_time,
-   output sync_rcvd,
-   input exp_pps_in);
+   output reg [63:0] vita_time,
+   output reg sync_rcvd,
+   input exp_time_in);
 
    wire       code_err, disp_err, dispout, complete_word;
    reg 	      disp_reg;
@@ -13,7 +13,7 @@ module time_receiver
    reg [8:0]  dataout_reg;
  	      
    always @(posedge clk)
-     shiftreg <= {exp_pps_in, shiftreg[9:1]};
+     shiftreg <= {exp_time_in, shiftreg[9:1]};
 
    localparam COMMA_0 = 10'h283;
    localparam COMMA_1 = 10'h17c;
@@ -55,40 +55,76 @@ module time_receiver
    localparam STATE_T1 = 2;
    localparam STATE_T2 = 3;
    localparam STATE_T3 = 4;
+   localparam STATE_T4 = 5;
+   localparam STATE_T5 = 6;
+   localparam STATE_T6 = 7;
+   localparam STATE_T7 = 8;
+   localparam STATE_TAIL = 9;
    
    localparam HEAD = 9'h13c;   
-
-   reg [7:0]  clock_a, clock_b, clock_c;
-   reg [2:0]  state;
+   localparam TAIL = 9'h1F7;
+   
+   reg [3:0]  state;
    
    always @(posedge clk)
      if(rst)
        state <= STATE_IDLE;
      else if(complete_word)
-       case(state)
-	 STATE_IDLE :
-	   if(dataout_reg == HEAD)
-	     state <= STATE_T0;
-	 STATE_T0 :
-	   begin
-	      clock_a <= dataout_reg[7:0];
-	      state <= STATE_T1;
-	   end
-	 STATE_T1 :
-	   begin
-	      clock_b <= dataout_reg[7:0];
-	      state <= STATE_T2;
-	   end
-	 STATE_T2 :
-	   begin
-	      clock_c <= dataout_reg[7:0];
-	      state <= STATE_T3;
-	   end
-	 STATE_T3 :
-	   state <= STATE_IDLE;
-       endcase // case(state)
-
-   assign master_time =  {clock_a, clock_b, clock_c, dataout_reg[7:0]};
-   assign sync_rcvd = (complete_word & (state == STATE_T3));
-
+       if(code_err | disp_err)
+	 state <= STATE_IDLE;
+       else
+	 case(state)
+	   STATE_IDLE :
+	     if(dataout_reg == HEAD)
+	       state <= STATE_T0;
+	   STATE_T0 :
+	     begin
+		vita_time[63:56] <= dataout_reg[7:0];
+		state <= STATE_T1;
+	     end
+	   STATE_T1 :
+	     begin
+		vita_time[55:48] <= dataout_reg[7:0];
+		state <= STATE_T2;
+	     end
+	   STATE_T2 :
+	     begin
+		vita_time[47:40] <= dataout_reg[7:0];
+		state <= STATE_T3;
+	     end
+	   STATE_T3 :
+	     begin
+		vita_time[39:32] <= dataout_reg[7:0];
+		state <= STATE_T4;
+	     end
+	   STATE_T4 :
+	     begin
+		vita_time[31:24] <= dataout_reg[7:0];
+		state <= STATE_T5;
+	     end
+	   STATE_T5 :
+	     begin
+		vita_time[23:16] <= dataout_reg[7:0];
+		state <= STATE_T6;
+	     end
+	   STATE_T6 :
+	     begin
+		vita_time[15:8] <= dataout_reg[7:0];
+		state <= STATE_T7;
+	     end
+	   STATE_T7 :
+	     begin
+		vita_time[7:0] <= dataout_reg[7:0];
+		state <= STATE_TAIL;
+	     end
+	   STATE_TAIL :
+	     state <= STATE_IDLE;
+	 endcase // case(state)
+   
+   always @(posedge clk)
+     if(rst)
+       sync_rcvd <= 0;
+     else
+       sync_rcvd <= (complete_word & (state == STATE_TAIL) & (dataout_reg[8:0] == TAIL));
+   
 endmodule // time_sender
diff --git a/fpga/usrp2/timing/time_sender.v b/fpga/usrp2/timing/time_sender.v
index aa2fcbbdb..f4ee5226a 100644
--- a/fpga/usrp2/timing/time_sender.v
+++ b/fpga/usrp2/timing/time_sender.v
@@ -2,23 +2,23 @@
 
 module time_sender
   (input clk, input rst,
-   input [31:0] master_time,
+   input [63:0] vita_time,
    input send_sync,
-   output exp_pps_out);
+   output reg exp_time_out);
 
    reg [7:0] datain;
    reg 	     k;
    wire [9:0] dataout;
-   reg [9:0] dataout_reg;
-   reg 	     disp_reg;
-   wire      disp, new_word;
+   reg [9:0]  dataout_reg;
+   reg 	      disp_reg;
+   wire       disp, new_word;
+   reg [4:0]  state;
+   reg [3:0]  bit_count;
    
    encode_8b10b encode_8b10b 
      (.datain({k,datain}),.dispin(disp_reg),
       .dataout(dataout),.dispout(disp));
 
-   assign    exp_pps_out = dataout_reg[0];
-
    always @(posedge clk)
      if(rst)
        disp_reg <= 0;
@@ -33,9 +33,9 @@ module time_sender
      else
        dataout_reg <= {1'b0,dataout_reg[9:1]};
    
-   reg [4:0] state;
-   reg [3:0] bit_count;
-
+   always @(posedge clk)
+     exp_time_out <= dataout_reg[0];
+   
    assign    new_word = (bit_count == 9);
    
    always @(posedge clk)
@@ -52,17 +52,23 @@ module time_sender
    localparam SEND_T1 = 3;
    localparam SEND_T2 = 4;
    localparam SEND_T3 = 5;
+   localparam SEND_T4 = 6;
+   localparam SEND_T5 = 7;
+   localparam SEND_T6 = 8;
+   localparam SEND_T7 = 9;
+   localparam SEND_TAIL = 10;
 
    localparam COMMA = 8'hBC;
    localparam HEAD = 8'h3C;
-
-   reg [31:0] master_time_reg;
+   localparam TAIL = 8'hF7;
+   
+   reg [63:0] vita_time_reg;
    
    always @(posedge clk)
      if(rst)
-       master_time_reg <= 0;
+       vita_time_reg <= 0;
      else if(send_sync)
-       master_time_reg <= master_time;
+       vita_time_reg <= vita_time;
    
    always @(posedge clk)
      if(rst)
@@ -84,27 +90,51 @@ module time_sender
 	     end
 	   SEND_T0 :
 	     begin
-		{k,datain} <= {1'b0, master_time_reg[31:24] };
+		{k,datain} <= {1'b0, vita_time_reg[63:56] };
 		state <= SEND_T1;
 	     end
 	   SEND_T1 :
 	     begin
-		{k,datain} <= {1'b0, master_time_reg[23:16]};
+		{k,datain} <= {1'b0, vita_time_reg[55:48]};
 		state <= SEND_T2;
 	     end
 	   SEND_T2 :
 	     begin
-		{k,datain} <= {1'b0, master_time_reg[15:8]};
+		{k,datain} <= {1'b0, vita_time_reg[47:40]};
 		state <= SEND_T3;
 	     end
 	   SEND_T3 :
 	     begin
-		{k,datain} <= {1'b0, master_time_reg[7:0]};
+		{k,datain} <= {1'b0, vita_time_reg[39:32]};
+		state <= SEND_T4;
+	     end
+	   SEND_T4 :
+	     begin
+		{k,datain} <= {1'b0, vita_time_reg[31:24]};
+		state <= SEND_T5;
+	     end
+	   SEND_T5 :
+	     begin
+		{k,datain} <= {1'b0, vita_time_reg[23:16]};
+		state <= SEND_T6;
+	     end
+	   SEND_T6 :
+	     begin
+		{k,datain} <= {1'b0, vita_time_reg[15:8]};
+		state <= SEND_T7;
+	     end
+	   SEND_T7 :
+	     begin
+		{k,datain} <= {1'b0, vita_time_reg[7:0]};
+		state <= SEND_TAIL;
+	     end
+	   SEND_TAIL :
+	     begin
+		{k,datain} <= {1'b1, TAIL};
 		state <= SEND_IDLE;
 	     end
 	   default :
 	     state <= SEND_IDLE;
 	 endcase // case(state)
    
-   
 endmodule // time_sender
diff --git a/fpga/usrp2/timing/time_transfer_tb.v b/fpga/usrp2/timing/time_transfer_tb.v
index 2b75c60bd..0c164f82c 100644
--- a/fpga/usrp2/timing/time_transfer_tb.v
+++ b/fpga/usrp2/timing/time_transfer_tb.v
@@ -18,12 +18,12 @@ module time_transfer_tb();
    
    initial #100000000 $finish;
 
-   wire exp_pps, pps, pps_rcv;
-   wire [31:0] master_clock_rcv;
-   reg [31:0]  master_clock = 0;
-   reg [31:0]  counter = 0;
+   wire exp_time, pps, pps_rcv;
+   wire [63:0] vita_time_rcv;
+   reg [63:0]  vita_time = 0;
+   reg [63:0]  counter = 0;
 
-   localparam  PPS_PERIOD = 109;
+   localparam  PPS_PERIOD = 439; // PPS_PERIOD % 10 must = 9
    always @(posedge clk)
      if(counter == PPS_PERIOD)
        counter <= 0;
@@ -32,19 +32,19 @@ module time_transfer_tb();
    assign      pps = (counter == (PPS_PERIOD-1));
    
    always @(posedge clk)
-     master_clock <= master_clock + 1;
+     vita_time <= vita_time + 1;
    
    time_sender time_sender
      (.clk(clk),.rst(rst),
-      .master_clock(master_clock),
-      .pps(pps),
-      .exp_pps_out(exp_pps) );
+      .vita_time(vita_time),
+      .send_sync(pps),
+      .exp_time_out(exp_time) );
 
    time_receiver time_receiver
      (.clk(clk),.rst(rst),
-      .master_clock(master_clock_rcv),
-      .pps(pps_rcv),
-      .exp_pps_in(exp_pps) );
+      .vita_time(vita_time_rcv),
+      .sync_rcvd(pps_rcv),
+      .exp_time_in(exp_time) );
 
-   wire [31:0] delta = master_clock - master_clock_rcv;
+   wire [31:0] delta = vita_time - vita_time_rcv;
 endmodule // time_transfer_tb
diff --git a/fpga/usrp2/top/u2_rev3/Makefile b/fpga/usrp2/top/u2_rev3/Makefile
index 68c296b9b..05ada2476 100644
--- a/fpga/usrp2/top/u2_rev3/Makefile
+++ b/fpga/usrp2/top/u2_rev3/Makefile
@@ -6,7 +6,7 @@
 # Project Setup
 ##################################################
 TOP_MODULE = u2_rev3
-BUILD_DIR = $(abspath build$(ISE))
+BUILD_DIR = $(abspath build)
 
 ##################################################
 # Include other makefiles
@@ -24,6 +24,8 @@ include ../../vrt/Makefile.srcs
 include ../../udp/Makefile.srcs
 include ../../coregen/Makefile.srcs
 include ../../extram/Makefile.srcs
+include ../../extramfifo/Makefile.srcs
+
 
 ##################################################
 # Project Properties
diff --git a/fpga/usrp2/top/u2_rev3/Makefile.udp b/fpga/usrp2/top/u2_rev3/Makefile.udp
deleted file mode 100644
index 99effb038..000000000
--- a/fpga/usrp2/top/u2_rev3/Makefile.udp
+++ /dev/null
@@ -1,99 +0,0 @@
-#
-# Copyright 2008 Ettus Research LLC
-#
-
-##################################################
-# Project Setup
-##################################################
-TOP_MODULE = u2_rev3
-BUILD_DIR = $(abspath build-udp$(ISE))
-
-##################################################
-# Include other makefiles
-##################################################
-
-include ../Makefile.common
-include ../../fifo/Makefile.srcs
-include ../../control_lib/Makefile.srcs
-include ../../sdr_lib/Makefile.srcs
-include ../../serdes/Makefile.srcs
-include ../../simple_gemac/Makefile.srcs
-include ../../timing/Makefile.srcs
-include ../../opencores/Makefile.srcs
-include ../../vrt/Makefile.srcs
-include ../../udp/Makefile.srcs
-include ../../coregen/Makefile.srcs
-include ../../extram/Makefile.srcs
-include ../../extramfifo/Makefile.srcs
-
-
-##################################################
-# Project Properties
-##################################################
-PROJECT_PROPERTIES = \
-family Spartan3 \
-device xc3s2000 \
-package fg456 \
-speed -5 \
-top_level_module_type "HDL" \
-synthesis_tool "XST (VHDL/Verilog)" \
-simulator "ISE Simulator (VHDL/Verilog)" \
-"Preferred Language" "Verilog" \
-"Enable Message Filtering" FALSE \
-"Display Incremental Messages" FALSE 
-
-##################################################
-# Sources
-##################################################
-TOP_SRCS = \
-u2_core_udp.v \
-u2_rev3.v \
-u2_rev3.ucf
-
-SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \
-$(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \
-$(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \
-$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS)
-
-##################################################
-# Process Properties
-##################################################
-SYNTHESIZE_PROPERTIES = \
-"Number of Clock Buffers" 8 \
-"Pack I/O Registers into IOBs" Yes \
-"Optimization Effort" High \
-"Optimize Instantiated Primitives" TRUE \
-"Register Balancing" Yes \
-"Use Clock Enable" Auto \
-"Use Synchronous Reset" Auto \
-"Use Synchronous Set" Auto
-
-TRANSLATE_PROPERTIES = \
-"Macro Search Path" "$(shell pwd)/../../coregen/"
-
-MAP_PROPERTIES = \
-"Allow Logic Optimization Across Hierarchy" TRUE \
-"Map to Input Functions" 4 \
-"Optimization Strategy (Cover Mode)" Speed \
-"Pack I/O Registers/Latches into IOBs" "For Inputs and Outputs" \
-"Perform Timing-Driven Packing and Placement" TRUE \
-"Map Effort Level" High \
-"Extra Effort" Normal \
-"Combinatorial Logic Optimization" TRUE \
-"Register Duplication" TRUE
-
-PLACE_ROUTE_PROPERTIES = \
-"Place & Route Effort Level (Overall)" High 
-
-STATIC_TIMING_PROPERTIES = \
-"Number of Paths in Error/Verbose Report" 10 \
-"Report Type" "Error Report"
-
-GEN_PROG_FILE_PROPERTIES = \
-"Configuration Rate" 6 \
-"Create Binary Configuration File" TRUE \
-"Done (Output Events)" 5 \
-"Enable Bitstream Compression" TRUE \
-"Enable Outputs (Output Events)" 6 
-
-SIM_MODEL_PROPERTIES = ""
diff --git a/fpga/usrp2/top/u2_rev3/u2_core.v b/fpga/usrp2/top/u2_rev3/u2_core.v
index a5963f6b1..30b47b818 100644
--- a/fpga/usrp2/top/u2_rev3/u2_core.v
+++ b/fpga/usrp2/top/u2_rev3/u2_core.v
@@ -17,8 +17,8 @@ module u2_core
    output [1:0] debug_clk,
 
    // Expansion
-   input exp_pps_in,
-   output exp_pps_out,
+   input exp_time_in,
+   output exp_time_out,
    
    // GMII
    //   GMII-CTRL
@@ -119,11 +119,12 @@ module u2_core
    inout [15:0] io_rx,
 
    // External RAM
-   inout [17:0] RAM_D,
+   input [17:0] RAM_D_pi,
+   output [17:0] RAM_D_po,   
+   output RAM_D_poe,
    output [18:0] RAM_A,
    output RAM_CE1n,
    output RAM_CENn,
- //  output RAM_CLK,
    output RAM_WEn,
    output RAM_OEn,
    output RAM_LDn,
@@ -142,7 +143,7 @@ module u2_core
    localparam SR_RX_CTRL  = 176;  // 16
    localparam SR_TIME64   = 192;  //  3
    localparam SR_SIMTIMER = 198;  //  2
-   localparam SR_TX_DSP   = 128;  // 16
+   localparam SR_TX_DSP   = 208;  // 16
    localparam SR_TX_CTRL  = 224;  // 16
 
    // FIFO Sizes, 9 = 512 lines, 10 = 1024, 11 = 2048
@@ -160,15 +161,17 @@ module u2_core
    
    wire 	ram_loader_done;
    wire 	ram_loader_rst, wb_rst, dsp_rst;
+   assign dsp_rst = wb_rst;
 
    wire [31:0] 	status, status_b0, status_b1, status_b2, status_b3, status_b4, status_b5, status_b6, status_b7;
-   wire 	bus_error, spi_int, i2c_int, pps_int, timer_int, buffer_int, proc_int, overrun, underrun, uart_tx_int, uart_rx_int;
+   wire 	bus_error, spi_int, i2c_int, pps_int, onetime_int, periodic_int, buffer_int;
+   wire 	proc_int, overrun, underrun, uart_tx_int, uart_rx_int;
 
    wire [31:0] 	debug_gpio_0, debug_gpio_1;
    wire [31:0] 	atr_lines;
 
-   wire [31:0] 	debug_rx, debug_mac, debug_mac0, debug_mac1, debug_tx_dsp, debug_txc, 
-		debug_serdes0, debug_serdes1, debug_serdes2, debug_rx_dsp;
+   wire [31:0] 	debug_rx, debug_mac, debug_mac0, debug_mac1, debug_tx_dsp, debug_txc,
+		debug_serdes0, debug_serdes1, debug_serdes2, debug_rx_dsp, debug_udp, debug_extfifo, debug_extfifo2;
 
    wire [15:0] 	ser_rx_occ, ser_tx_occ, dsp_rx_occ, dsp_tx_occ, eth_rx_occ, eth_tx_occ, eth_rx_occ2;
    wire 	ser_rx_full, ser_tx_full, dsp_rx_full, dsp_tx_full, eth_rx_full, eth_tx_full, eth_rx_full2;
@@ -177,6 +180,12 @@ module u2_core
    wire 	serdes_link_up;
    wire 	epoch;
    wire [31:0] 	irq;
+   wire [63:0] 	vita_time;
+   
+   wire 	 run_rx, run_tx;
+   reg 		 run_rx_d1;
+   always @(posedge dsp_clk)
+     run_rx_d1 <= run_rx;
    
    // ///////////////////////////////////////////////////////////////////////////////////////////////
    // Wishbone Single Master INTERCON
@@ -405,7 +414,7 @@ module u2_core
 		 .cyc_i(s4_cyc),.stb_i(s4_stb),.adr_i(s4_adr[3:0]),.we_i(s4_we),
 		 .dat_i(s4_dat_o),.dat_o(s4_dat_i),.ack_o(s4_ack),
 		 .atr(atr_lines),.debug_0(debug_gpio_0),.debug_1(debug_gpio_1),
-		 .gpio( {io_tx,io_rx} ) );
+		 .gpio({io_tx,io_rx}) );
 
    // /////////////////////////////////////////////////////////////////////////
    // Buffer Pool Status -- Slave #5   
@@ -416,33 +425,70 @@ module u2_core
        cycle_count <= 0;
      else
        cycle_count <= cycle_count + 1;
-   
+
+   //compatibility number -> increment when the fpga has been sufficiently altered
+   localparam compat_num = 32'd3;
+
    wb_readback_mux buff_pool_status
      (.wb_clk_i(wb_clk), .wb_rst_i(wb_rst), .wb_stb_i(s5_stb),
       .wb_adr_i(s5_adr), .wb_dat_o(s5_dat_i), .wb_ack_o(s5_ack),
       
       .word00(status_b0),.word01(status_b1),.word02(status_b2),.word03(status_b3),
       .word04(status_b4),.word05(status_b5),.word06(status_b6),.word07(status_b7),
-      .word08(status),.word09({sim_mode,27'b0,clock_divider[3:0]}),.word10(32'b0),
-      .word11(32'b0),.word12(32'b0),.word13(irq),.word14(status_enc),.word15(cycle_count)
+      .word08(status),.word09({sim_mode,27'b0,clock_divider[3:0]}),.word10(vita_time[63:32]),
+      .word11(vita_time[31:0]),.word12(compat_num),.word13(irq),.word14(status_enc),.word15(cycle_count)
       );
 
    // /////////////////////////////////////////////////////////////////////////
    // Ethernet MAC  Slave #6
 
-   simple_gemac_wrapper #(.RXFIFOSIZE(11), .TXFIFOSIZE(6)) simple_gemac_wrapper
+   wire [18:0] 	 rx_f19_data, tx_f19_data;
+   wire 	 rx_f19_src_rdy, rx_f19_dst_rdy, rx_f36_src_rdy, rx_f36_dst_rdy;
+   
+   simple_gemac_wrapper19 #(.RXFIFOSIZE(11), .TXFIFOSIZE(6)) simple_gemac_wrapper19
      (.clk125(clk_to_mac),  .reset(wb_rst),
       .GMII_GTX_CLK(GMII_GTX_CLK), .GMII_TX_EN(GMII_TX_EN),  
       .GMII_TX_ER(GMII_TX_ER), .GMII_TXD(GMII_TXD),
       .GMII_RX_CLK(GMII_RX_CLK), .GMII_RX_DV(GMII_RX_DV),  
       .GMII_RX_ER(GMII_RX_ER), .GMII_RXD(GMII_RXD),
       .sys_clk(dsp_clk),
-      .rx_f36_data({wr2_flags,wr2_dat}), .rx_f36_src_rdy(wr2_ready_i), .rx_f36_dst_rdy(wr2_ready_o),
-      .tx_f36_data({rd2_flags,rd2_dat}), .tx_f36_src_rdy(rd2_ready_o), .tx_f36_dst_rdy(rd2_ready_i),
+      .rx_f19_data(rx_f19_data), .rx_f19_src_rdy(rx_f19_src_rdy), .rx_f19_dst_rdy(rx_f19_dst_rdy),
+      .tx_f19_data(tx_f19_data), .tx_f19_src_rdy(tx_f19_src_rdy), .tx_f19_dst_rdy(tx_f19_dst_rdy),
       .wb_clk(wb_clk), .wb_rst(wb_rst), .wb_stb(s6_stb), .wb_cyc(s6_cyc), .wb_ack(s6_ack),
       .wb_we(s6_we), .wb_adr(s6_adr), .wb_dat_i(s6_dat_o), .wb_dat_o(s6_dat_i),
       .mdio(MDIO), .mdc(MDC),
       .debug(debug_mac));
+
+   wire [35:0] 	 udp_tx_data, udp_rx_data;
+   wire 	 udp_tx_src_rdy, udp_tx_dst_rdy, udp_rx_src_rdy, udp_rx_dst_rdy;
+   
+   udp_wrapper #(.BASE(SR_UDP_SM)) udp_wrapper
+     (.clk(dsp_clk), .reset(dsp_rst), .clear(0),
+      .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
+      .rx_f19_data(rx_f19_data), .rx_f19_src_rdy_i(rx_f19_src_rdy), .rx_f19_dst_rdy_o(rx_f19_dst_rdy),
+      .tx_f19_data(tx_f19_data), .tx_f19_src_rdy_o(tx_f19_src_rdy), .tx_f19_dst_rdy_i(tx_f19_dst_rdy),
+      .rx_f36_data(udp_rx_data), .rx_f36_src_rdy_o(udp_rx_src_rdy), .rx_f36_dst_rdy_i(udp_rx_dst_rdy),
+      .tx_f36_data(udp_tx_data), .tx_f36_src_rdy_i(udp_tx_src_rdy), .tx_f36_dst_rdy_o(udp_tx_dst_rdy),
+      .debug(debug_udp) );
+
+   wire [35:0] 	 tx_err_data, udp1_tx_data;
+   wire 	 tx_err_src_rdy, tx_err_dst_rdy, udp1_tx_src_rdy, udp1_tx_dst_rdy;
+   
+   fifo_cascade #(.WIDTH(36), .SIZE(ETH_TX_FIFOSIZE)) tx_eth_fifo
+     (.clk(dsp_clk), .reset(dsp_rst), .clear(0),
+      .datain({rd2_flags,rd2_dat}), .src_rdy_i(rd2_ready_o), .dst_rdy_o(rd2_ready_i),
+      .dataout(udp1_tx_data), .src_rdy_o(udp1_tx_src_rdy), .dst_rdy_i(udp1_tx_dst_rdy));
+
+   fifo36_mux #(.prio(0)) mux_err_stream
+     (.clk(dsp_clk), .reset(dsp_reset), .clear(0),
+      .data0_i(udp1_tx_data), .src0_rdy_i(udp1_tx_src_rdy), .dst0_rdy_o(udp1_tx_dst_rdy),
+      .data1_i(tx_err_data), .src1_rdy_i(tx_err_src_rdy), .dst1_rdy_o(tx_err_dst_rdy),
+      .data_o(udp_tx_data), .src_rdy_o(udp_tx_src_rdy), .dst_rdy_i(udp_tx_dst_rdy));
+   
+   fifo_cascade #(.WIDTH(36), .SIZE(ETH_RX_FIFOSIZE)) rx_eth_fifo
+     (.clk(dsp_clk), .reset(dsp_rst), .clear(0),
+      .datain(udp_rx_data), .src_rdy_i(udp_rx_src_rdy), .dst_rdy_o(udp_rx_dst_rdy),
+      .dataout({wr2_flags,wr2_dat}), .src_rdy_o(wr2_ready_i), .dst_rdy_i(wr2_ready_o));
    
    // /////////////////////////////////////////////////////////////////////////
    // Settings Bus -- Slave #7
@@ -482,22 +528,30 @@ module u2_core
    //    In Rev3 there are only 6 leds, and the highest one is on the ETH connector
    
    wire [7:0] 	 led_src, led_sw;
-   wire [7:0] 	 led_hw = {clk_status,serdes_link_up};
+   wire [7:0] 	 led_hw = {run_tx, run_rx, clk_status, serdes_link_up, 1'b0};
    
    setting_reg #(.my_addr(3),.width(8)) sr_led (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
 				      .in(set_data),.out(led_sw),.changed());
-   setting_reg #(.my_addr(8),.width(8)) sr_led_src (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
-					  .in(set_data),.out(led_src),.changed());
+
+   setting_reg #(.my_addr(8),.width(8), .at_reset(8'b0001_1110)) 
+   sr_led_src (.clk(wb_clk),.rst(wb_rst), .strobe(set_stb),.addr(set_addr), .in(set_data),.out(led_src),.changed());
 
    assign 	 leds = (led_src & led_hw) | (~led_src & led_sw);
    
    // /////////////////////////////////////////////////////////////////////////
    // Interrupt Controller, Slave #8
 
+   // Pass interrupts on dsp_clk to wb_clk.  These need edge triggering in the pic
+   wire 	 underrun_wb, overrun_wb, pps_wb;
+
+   oneshot_2clk underrun_1s (.clk_in(dsp_clk), .in(underrun), .clk_out(wb_clk), .out(underrun_wb));
+   oneshot_2clk overrun_1s (.clk_in(dsp_clk), .in(overrun), .clk_out(wb_clk), .out(overrun_wb));
+   oneshot_2clk pps_1s (.clk_in(dsp_clk), .in(pps_int), .clk_out(wb_clk), .out(pps_wb));
+   
    assign irq= {{8'b0},
 		{8'b0},
-		{4'b0, clk_status, serdes_link_up, uart_tx_int, uart_rx_int},
-		{pps_int,overrun,underrun,PHY_INTn,i2c_int,spi_int,timer_int,buffer_int}};
+		{3'b0, periodic_int, clk_status, serdes_link_up, uart_tx_int, uart_rx_int},
+		{pps_wb,overrun_wb,underrun_wb,PHY_INTn,i2c_int,spi_int,onetime_int,buffer_int}};
    
    pic pic(.clk_i(wb_clk),.rst_i(wb_rst),.cyc_i(s8_cyc),.stb_i(s8_stb),.adr_i(s8_adr[4:2]),
 	   .we_i(s8_we),.dat_i(s8_dat_o),.dat_o(s8_dat_i),.ack_o(s8_ack),.int_o(proc_int),
@@ -506,13 +560,17 @@ module u2_core
    // /////////////////////////////////////////////////////////////////////////
    // Master Timer, Slave #9
 
-   wire [31:0] 	 master_time;
-   timer timer
-     (.wb_clk_i(wb_clk),.rst_i(wb_rst),
-      .cyc_i(s9_cyc),.stb_i(s9_stb),.adr_i(s9_adr[4:2]),
-      .we_i(s9_we),.dat_i(s9_dat_o),.dat_o(s9_dat_i),.ack_o(s9_ack),
-      .sys_clk_i(dsp_clk),.master_time_i(master_time),.int_o(timer_int) );
-
+   // No longer used, replaced with simple_timer below
+   assign s9_ack = 0;
+   
+   // /////////////////////////////////////////////////////////////////////////
+   //  Simple Timer interrupts
+   
+   simple_timer #(.BASE(SR_SIMTIMER)) simple_timer
+     (.clk(wb_clk), .reset(wb_rst),
+      .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
+      .onetime_int(onetime_int), .periodic_int(periodic_int));
+   
    // /////////////////////////////////////////////////////////////////////////
    // UART, Slave #10
 
@@ -526,11 +584,6 @@ module u2_core
    // /////////////////////////////////////////////////////////////////////////
    // ATR Controller, Slave #11
 
-   wire 	 run_rx, run_tx;
-   reg 		 run_rx_d1;
-   always @(posedge dsp_clk)
-     run_rx_d1 <= run_rx;
-   
    atr_controller atr_controller
      (.clk_i(wb_clk),.rst_i(wb_rst),
       .adr_i(sb_adr[5:0]),.sel_i(sb_sel),.dat_i(sb_dat_o),.dat_o(sb_dat_i),
@@ -540,22 +593,9 @@ module u2_core
    // //////////////////////////////////////////////////////////////////////////
    // Time Sync, Slave #12 
 
-   reg 		 pps_posedge, pps_negedge, pps_pos_d1, pps_neg_d1;
-   always @(negedge dsp_clk) pps_negedge <= pps_in;
-   always @(posedge dsp_clk) pps_posedge <= pps_in;
-   always @(posedge dsp_clk) pps_pos_d1 <= pps_posedge;
-   always @(posedge dsp_clk) pps_neg_d1 <= pps_negedge;   
-   
-   wire 	 pps_o;
-   time_sync time_sync
-     (.wb_clk_i(wb_clk),.rst_i(wb_rst),
-      .cyc_i(sc_cyc),.stb_i(sc_stb),.adr_i(sc_adr[4:2]),
-      .we_i(sc_we),.dat_i(sc_dat_o),.dat_o(sc_dat_i),.ack_o(sc_ack),
-      .sys_clk_i(dsp_clk),.master_time_o(master_time),
-      .pps_posedge(pps_posedge),.pps_negedge(pps_negedge),
-      .exp_pps_in(exp_pps_in),.exp_pps_out(exp_pps_out),
-      .int_o(pps_int),.epoch_o(epoch),.pps_o(pps_o) );
-
+   // No longer used, see time_64bit.  Still need to handle mimo time, though
+   assign sc_ack = 0;
+   
    // /////////////////////////////////////////////////////////////////////////
    // SD Card Reader / Writer, Slave #13
 
@@ -569,45 +609,100 @@ module u2_core
    assign sd_dat_i[31:8] = 0;
 
    // /////////////////////////////////////////////////////////////////////////
-   // DSP
+   // DSP RX
    wire [31:0] 	 sample_rx, sample_tx;
    wire 	 strobe_rx, strobe_tx;
-
-   rx_control #(.FIFOSIZE(10)) rx_control
-     (.clk(dsp_clk), .rst(dsp_rst),
-      .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
-      .master_time(master_time),.overrun(overrun),
-      .wr_dat_o(wr1_dat), .wr_flags_o(wr1_flags), .wr_ready_o(wr1_ready_i), .wr_ready_i(wr1_ready_o),
-      .sample(sample_rx), .run(run_rx), .strobe(strobe_rx),
-      .fifo_occupied(dsp_rx_occ),.fifo_full(dsp_rx_full),.fifo_empty(dsp_rx_empty),
-      .debug_rx(debug_rx) );
+   wire 	 rx_dst_rdy, rx_src_rdy, rx1_dst_rdy, rx1_src_rdy;
+   wire [99:0] 	 rx_data;
+   wire [35:0] 	 rx1_data;
    
-   dsp_core_rx_old dsp_core_rx_old
+   dsp_core_rx #(.BASE(SR_RX_DSP)) dsp_core_rx
      (.clk(dsp_clk),.rst(dsp_rst),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
       .adc_a(adc_a),.adc_ovf_a(adc_ovf_a),.adc_b(adc_b),.adc_ovf_b(adc_ovf_b),
       .sample(sample_rx), .run(run_rx_d1), .strobe(strobe_rx),
       .debug(debug_rx_dsp) );
 
-   tx_control #(.FIFOSIZE(10)) tx_control
-     (.clk(dsp_clk), .rst(dsp_rst),
-      .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
-      .master_time(master_time),.underrun(underrun),
-      .rd_dat_i(rd1_dat), .rd_flags_i(rd1_flags), .rd_ready_i(rd1_ready_o), .rd_ready_o(rd1_ready_i),
-      .sample(sample_tx), .run(run_tx), .strobe(strobe_tx),
-      .fifo_occupied(dsp_tx_occ),.fifo_full(dsp_tx_full),.fifo_empty(dsp_tx_empty),
-      .debug(debug_txc) );
+   wire [31:0] 	 vrc_debug;
+   wire 	 clear_rx;
    
-   dsp_core_tx #(.BASE(SR_TX_DSP)) dsp_core_tx
+   setting_reg #(.my_addr(SR_RX_CTRL+3)) sr_clear
      (.clk(dsp_clk),.rst(dsp_rst),
+      .strobe(set_stb_dsp),.addr(set_addr_dsp),.in(set_data_dsp),
+      .out(),.changed(clear_rx));
+
+   vita_rx_control #(.BASE(SR_RX_CTRL), .WIDTH(32)) vita_rx_control
+     (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx),
       .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
-      .sample(sample_tx), .run(run_tx), .strobe(strobe_tx),
-      .dac_a(dac_a),.dac_b(dac_b),
-      .debug(debug_tx_dsp) );
+      .vita_time(vita_time), .overrun(overrun),
+      .sample(sample_rx), .run(run_rx), .strobe(strobe_rx),
+      .sample_fifo_o(rx_data), .sample_fifo_dst_rdy_i(rx_dst_rdy), .sample_fifo_src_rdy_o(rx_src_rdy),
+      .debug_rx(vrc_debug));
 
-   assign dsp_rst = wb_rst;
+   wire [3:0] 	 vita_state;
+   
+   vita_rx_framer #(.BASE(SR_RX_CTRL), .MAXCHAN(1)) vita_rx_framer
+     (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx),
+      .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+      .sample_fifo_i(rx_data), .sample_fifo_dst_rdy_o(rx_dst_rdy), .sample_fifo_src_rdy_i(rx_src_rdy),
+      .data_o(rx1_data), .dst_rdy_i(rx1_dst_rdy), .src_rdy_o(rx1_src_rdy),
+      .fifo_occupied(), .fifo_full(), .fifo_empty(),
+      .debug_rx(vita_state) );
+
+   fifo_cascade #(.WIDTH(36), .SIZE(DSP_RX_FIFOSIZE)) rx_fifo_cascade
+     (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx),
+      .datain(rx1_data), .src_rdy_i(rx1_src_rdy), .dst_rdy_o(rx1_dst_rdy),
+      .dataout({wr1_flags,wr1_dat}), .src_rdy_o(wr1_ready_i), .dst_rdy_i(wr1_ready_o));
 
    // ///////////////////////////////////////////////////////////////////////////////////
+   // DSP TX
+
+   wire [35:0] 	 tx_data;
+   wire 	 tx_src_rdy, tx_dst_rdy;
+   wire [31:0] 	 debug_vt;
+   wire 	 clear_tx;
+
+   setting_reg #(.my_addr(SR_TX_CTRL+1)) sr_clear_tx
+     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
+      .in(set_data),.out(),.changed(clear_tx));
+
+   ext_fifo #(.EXT_WIDTH(18),.INT_WIDTH(36),.RAM_DEPTH(19),.FIFO_DEPTH(19)) 
+     ext_fifo_i1
+       (.int_clk(dsp_clk),
+	.ext_clk(clk_to_mac),
+	.rst(dsp_rst | clear_tx),
+	.RAM_D_pi(RAM_D_pi),
+	.RAM_D_po(RAM_D_po),
+	.RAM_D_poe(RAM_D_poe),
+	.RAM_A(RAM_A),
+	.RAM_WEn(RAM_WEn),
+	.RAM_CENn(RAM_CENn),
+	.RAM_LDn(RAM_LDn),
+	.RAM_OEn(RAM_OEn),
+	.RAM_CE1n(RAM_CE1n),
+	.datain({rd1_flags[3:2],rd1_dat[31:16],rd1_flags[1:0],rd1_dat[15:0]}),
+	.src_rdy_i(rd1_ready_o),
+	.dst_rdy_o(rd1_ready_i),
+	.dataout({tx_data[35:34],tx_data[31:16],tx_data[33:32],tx_data[15:0]}),
+	.src_rdy_o(tx_src_rdy),
+	.dst_rdy_i(tx_dst_rdy),
+	.debug(debug_extfifo),
+	.debug2(debug_extfifo2) );
+
+   vita_tx_chain #(.BASE_CTRL(SR_TX_CTRL), .BASE_DSP(SR_TX_DSP), 
+		   .REPORT_ERROR(1), .DO_FLOW_CONTROL(1),
+		   .PROT_ENG_FLAGS(1), .USE_TRANS_HEADER(1)) 
+   vita_tx_chain
+     (.clk(dsp_clk), .reset(dsp_rst),
+      .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+      .vita_time(vita_time),
+      .tx_data_i(tx_data), .tx_src_rdy_i(tx_src_rdy), .tx_dst_rdy_o(tx_dst_rdy),
+      .err_data_o(tx_err_data), .err_src_rdy_o(tx_err_src_rdy), .err_dst_rdy_i(tx_err_dst_rdy),
+      .dac_a(dac_a),.dac_b(dac_b),
+      .underrun(underrun), .run(run_tx),
+      .debug(debug_vt));
+   
+   // ///////////////////////////////////////////////////////////////////////////////////
    // SERDES
 
    serdes #(.TXFIFOSIZE(SERDES_TX_FIFOSIZE),.RXFIFOSIZE(SERDES_RX_FIFOSIZE)) serdes
@@ -620,166 +715,25 @@ module u2_core
       .rx_occupied(ser_rx_occ),.rx_full(ser_rx_full),.rx_empty(ser_rx_empty),
       .serdes_link_up(serdes_link_up),.debug0(debug_serdes0), .debug1(debug_serdes1) );
 
-   // ///////////////////////////////////////////////////////////////////////////////////
-   // External RAM Interface
-/*
-   localparam PAGE_SIZE = 10;  // PAGE SIZE is in bytes, 10 = 1024 bytes
-
-   wire [15:0] bus2ram, ram2bus;
-   wire [15:0] bridge_adr;
-   wire [1:0]  bridge_sel;
-   wire        bridge_stb, bridge_cyc, bridge_we, bridge_ack;
-   
-   wire [19:0] page;
-   wire [19:0] wb_ram_adr = {page[19:PAGE_SIZE],bridge_adr[PAGE_SIZE-1:0]};
-   setting_reg #(.my_addr(6),.width(20)) sr_page (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
-				       .in(set_data),.out(page),.changed());
-
-   wb_bridge_16_32 bridge
-     (.wb_clk(wb_clk),.wb_rst(wb_rst),
-      .A_cyc_i(se_cyc),.A_stb_i(se_stb),.A_we_i(se_we),.A_sel_i(se_sel),
-      .A_adr_i(se_adr),.A_dat_i(se_dat_o),.A_dat_o(se_dat_i),.A_ack_o(se_ack),
-      .B_cyc_o(bridge_cyc),.B_stb_o(bridge_stb),.B_we_o(bridge_we),.B_sel_o(bridge_sel),
-      .B_adr_o(bridge_adr),.B_dat_o(bus2ram),.B_dat_i(ram2bus),.B_ack_i(bridge_ack));
-
-   wb_zbt16_b wb_zbt16_b
-     (.clk(wb_clk),.rst(wb_rst),
-      .wb_adr_i(wb_ram_adr),.wb_dat_i(bus2ram),.wb_dat_o(ram2bus),.wb_sel_i(bridge_sel),
-      .wb_cyc_i(bridge_cyc),.wb_stb_i(bridge_stb),.wb_ack_o(bridge_ack),.wb_we_i(bridge_we),
-      .sram_clk(RAM_CLK),.sram_a(RAM_A),.sram_d(RAM_D[15:0]),.sram_we(RAM_WEn),
-      .sram_bw(),.sram_adv(RAM_LDn),.sram_ce(RAM_CENn),.sram_oe(RAM_OEn),
-      .sram_mode(),.sram_zz() );
-
-*/
-   assign      RAM_CE1n = 0;
-   assign      RAM_D[17:16] = 2'bzz;
+   assign RAM_CLK = clk_to_mac;
    
-   // /////////////////////////////////////////////////////////////////////////////////////////
-   // Debug Pins
-   
-   // FIFO Level Debugging
-   reg [31:0]  host_to_dsp_fifo,dsp_to_host_fifo,eth_mac_debug,serdes_to_dsp_fifo,dsp_to_serdes_fifo;
-   
-   always @(posedge dsp_clk)
-     serdes_to_dsp_fifo <= { {ser_rx_full,ser_rx_empty,ser_rx_occ[13:0]},
-			     {dsp_tx_full,dsp_tx_empty,dsp_tx_occ[13:0]} };
+   // /////////////////////////////////////////////////////////////////////////
+   // VITA Timing
 
-   always @(posedge dsp_clk)
-     dsp_to_serdes_fifo <= { {ser_tx_full,ser_tx_empty,ser_tx_occ[13:0]},
-			     {dsp_rx_full,dsp_rx_empty,dsp_rx_occ[13:0]} };
+   wire [31:0] 	 debug_sync;
    
-   always @(posedge dsp_clk)
-     host_to_dsp_fifo <= { {eth_rx_full,eth_rx_empty,eth_rx_occ[13:0]},
-			   {dsp_tx_full,dsp_tx_empty,dsp_tx_occ[13:0]} };
+   time_64bit #(.TICKS_PER_SEC(32'd100000000),.BASE(SR_TIME64)) time_64bit
+     (.clk(dsp_clk), .rst(dsp_rst), .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
+      .pps(pps_in), .vita_time(vita_time), .pps_int(pps_int),
+      .exp_time_in(exp_time_in), .exp_time_out(exp_time_out),
+      .debug(debug_sync));
    
-   always @(posedge dsp_clk)
-     dsp_to_host_fifo <= { {eth_tx_full,eth_tx_empty,eth_tx_occ[13:0]},
-			   {dsp_rx_full,dsp_rx_empty,dsp_rx_occ[13:0]} };
-   
-   always @(posedge dsp_clk)
-     eth_mac_debug <= { { 6'd0, GMII_TX_EN, GMII_RX_DV, debug_mac0[7:0]},
-			{eth_rx_full2, eth_rx_empty2, eth_rx_occ2[13:0]} };
-   
-   assign  debug_clk[0]  = 0; // wb_clk;
-   assign  debug_clk[1]  = clk_to_mac;	
-/*
- 
-   wire        mdio_cpy  = MDIO;
-   assign  debug 	 = { { 1'b0, s6_stb, s6_ack, s6_we, s6_sel[3:0] },
-			     { s6_adr[15:8] },
-			     { s6_adr[7:0] },
-			     { 6'd0, mdio_cpy, MDC } };
-*/
-/*
-   assign debug 	 = { { GMII_TXD },
-			     { 5'd0, GMII_TX_EN, GMII_TX_ER, GMII_GTX_CLK },
-			     { wr2_flags, rd2_flags },
-			     { 4'd0, wr2_ready_i, wr2_ready_o, rd2_ready_i, rd2_ready_o } };
- */        
-   assign debug 	 = { { GMII_RXD },
-			     { 5'd0, GMII_RX_DV, GMII_RX_ER, GMII_RX_CLK },
-			     { wr2_flags, rd2_flags },
-			     { GMII_TX_EN,3'd0, wr2_ready_i, wr2_ready_o, rd2_ready_i, rd2_ready_o } };
-          
-   assign  debug_gpio_0 = 0;
- //debug_mac; //eth_mac_debug;
-   assign  debug_gpio_1 = 0;
+   // /////////////////////////////////////////////////////////////////////////////////////////
+   // Debug Pins
+  
+   assign debug_clk = 2'b00; // {dsp_clk, clk_to_mac};
+   assign debug = 32'd0; // debug_extfifo;
+   assign debug_gpio_0 = 32'd0;
+   assign debug_gpio_1 = 32'd0;
    
 endmodule // u2_core
-
-//   wire        debug_mux;
-//   setting_reg #(.my_addr(5)) sr_debug (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
-//					.in(set_data),.out(debug_mux),.changed());
-
-//assign     debug = debug_mux ? host_to_dsp_fifo : dsp_to_host_fifo;
-//assign     debug = debug_mux ? serdes_to_dsp_fifo : dsp_to_serdes_fifo;
-   
-//assign      debug = {{strobe_rx,/*adc_ovf_a*/ 1'b0,adc_a},
-//		{run_rx,/*adc_ovf_b*/ 1'b0,adc_b}};
-
-//assign      debug = debug_tx_dsp;
-//assign      debug = debug_serdes0;
-
-//assign      debug_gpio_0 = 0; //debug_serdes0;
-//assign      debug_gpio_1 = 0; //debug_serdes1;
-
-//   assign      debug={{3'b0, wb_clk, wb_rst, dsp_rst, por, config_success},
-//	      {8'b0},
-//      {3'b0,ram_loader_ack, ram_loader_stb, ram_loader_we,ram_loader_rst,ram_loader_done },
-//    {cpld_start,cpld_mode,cpld_done,cpld_din,cpld_clk,cpld_detached,cpld_misc,cpld_init_b} };
-
-//assign      debug = {dac_a,dac_b};
-
-/*
- assign      debug = {{ram_loader_done, takeover, 6'd0},
- {1'b0, cpld_start_int, cpld_mode_int, cpld_done_int, sd_clk, sd_csn, sd_miso, sd_mosi},
- {8'd0},
- {cpld_start, cpld_mode, cpld_done, cpld_din, cpld_misc, cpld_detached, cpld_clk, cpld_init_b}}; */
-
-/*assign      debug = host_to_dsp_fifo;
- assign      debug_gpio_0 = eth_mac_debug;
- assign      debug_gpio_1 = 0;
- */
-// Assign various commonly used debug buses.
-/*
- wire [31:0] debug_rx_1 = {uart_tx_o,GMII_TX_EN,strobe_rx,overrun,proc_int,buffer_int,timer_int,GMII_RX_DV,
- irq[7:0],
- GMII_RXD,
- GMII_TXD};
- 
- wire [31:0] debug_rx_2 = { 5'd0, s8_we, s8_stb, s8_ack, debug_rx[23:0] };
-   
-   wire [31:0] debug_time =  {uart_tx_o, 7'b0,
-			      irq[7:0],
-			      6'b0, GMII_RX_DV, GMII_TX_EN,
-			      4'b0, exp_pps_in, exp_pps_out, pps_in, pps_int};
-
-   wire [31:0] debug_irq =  {uart_tx_o, iwb_adr, iwb_ack,
-			     irq[7:0],
-			     proc_int,  7'b0 };
-
-   wire [31:0] debug_eth = 
-	       {{uart_tx_o,proc_int,underrun,buffer_int,wr2_ready,wr2_error,wr2_done,wr2_write},
-		{8'd0},
-		{8'd0},
-		{GMII_TX_EN,GMII_RX_DV,Rx_mac_empty,Rx_mac_rd,Rx_mac_err,Rx_mac_sop,Rx_mac_eop,wr2_full} };
-
-   assign      debug_serdes0 = { { rd0_dat[7:0] },
-				 { ser_tx_clk, ser_tkmsb, ser_tklsb, rd0_sop, rd0_eop, rd0_read, rd0_error, rd0_done },
-				 { ser_t[15:8] },
-				 { ser_t[7:0] } };
-
-   assign      debug_serdes1 = { {1'b0,proc_int,underrun,buffer_int,wr0_ready,wr0_error,wr0_done,wr0_write},
-				 { 1'b0, ser_rx_clk, ser_rkmsb, ser_rklsb, ser_enable, ser_prbsen, ser_loopen, ser_rx_en },
-				 { ser_r[15:8] },
-				 { ser_r[7:0] } };
-       
-   assign      debug_gpio_1 = {uart_tx_o,7'd0,
-			       3'd0,rd1_sop,rd1_eop,rd1_read,rd1_done,rd1_error,
-			       debug_txc[15:0]};
-   assign      debug_gpio_1 = debug_rx;
-   assign      debug_gpio_1 = debug_serdes1;
-   assign      debug_gpio_1 = debug_eth;
-      
-    */
-      
diff --git a/fpga/usrp2/top/u2_rev3/u2_core_udp.v b/fpga/usrp2/top/u2_rev3/u2_core_udp.v
deleted file mode 100644
index 9e62ee1cc..000000000
--- a/fpga/usrp2/top/u2_rev3/u2_core_udp.v
+++ /dev/null
@@ -1,735 +0,0 @@
-// ////////////////////////////////////////////////////////////////////////////////
-// Module Name:    u2_core
-// ////////////////////////////////////////////////////////////////////////////////
-
-module u2_core
-  #(parameter RAM_SIZE=32768)
-  (// Clocks
-   input dsp_clk,
-   input wb_clk,
-   output clock_ready,
-   input clk_to_mac,
-   input pps_in,
-   
-   // Misc, debug
-   output [7:0] leds,
-   output [31:0] debug,
-   output [1:0] debug_clk,
-
-   // Expansion
-   input exp_pps_in,
-   output exp_pps_out,
-   
-   // GMII
-   //   GMII-CTRL
-   input GMII_COL,
-   input GMII_CRS,
-
-   //   GMII-TX
-   output [7:0] GMII_TXD,
-   output GMII_TX_EN,
-   output GMII_TX_ER,
-   output GMII_GTX_CLK,
-   input GMII_TX_CLK,  // 100mbps clk
-
-   //   GMII-RX
-   input [7:0] GMII_RXD,
-   input GMII_RX_CLK,
-   input GMII_RX_DV,
-   input GMII_RX_ER,
-
-   //   GMII-Management
-   inout MDIO,
-   output MDC,
-   input PHY_INTn,   // open drain
-   output PHY_RESETn,
-
-   // SERDES
-   output ser_enable,
-   output ser_prbsen,
-   output ser_loopen,
-   output ser_rx_en,
-   
-   output ser_tx_clk,
-   output [15:0] ser_t,
-   output ser_tklsb,
-   output ser_tkmsb,
-
-   input ser_rx_clk,
-   input [15:0] ser_r,
-   input ser_rklsb,
-   input ser_rkmsb,
-   
-   // CPLD interface
-   output cpld_start,
-   output cpld_mode,
-   output cpld_done,
-   input cpld_din,
-   input cpld_clk,
-   input cpld_detached,
-   output cpld_misc,
-   input cpld_init_b,
-   input por,
-   output config_success,
-   
-   // ADC
-   input [13:0] adc_a,
-   input adc_ovf_a,
-   output adc_on_a,
-   output adc_oe_a,
-   
-   input [13:0] adc_b,
-   input adc_ovf_b,
-   output adc_on_b,
-   output adc_oe_b,
-   
-   // DAC
-   output [15:0] dac_a,
-   output [15:0] dac_b,
-
-   // I2C
-   input scl_pad_i,
-   output scl_pad_o,
-   output scl_pad_oen_o,
-   input sda_pad_i,
-   output sda_pad_o,
-   output sda_pad_oen_o,
-   
-   // Clock Gen Control
-   output [1:0] clk_en,
-   output [1:0] clk_sel,
-   input clk_func,        // FIXME is an input to control the 9510
-   input clk_status,
-
-   // Generic SPI
-   output sclk,
-   output mosi,
-   input miso,
-   output sen_clk,
-   output sen_dac,
-   output sen_tx_db,
-   output sen_tx_adc,
-   output sen_tx_dac,
-   output sen_rx_db,
-   output sen_rx_adc,
-   output sen_rx_dac,
-   
-   // GPIO to DBoards
-   inout [15:0] io_tx,
-   inout [15:0] io_rx,
-
-   // External RAM
-   input [17:0] RAM_D_pi,
-   output [17:0] RAM_D_po,   
-   output RAM_D_poe,
-   output [18:0] RAM_A,
-   output RAM_CE1n,
-   output RAM_CENn,
-   output RAM_WEn,
-   output RAM_OEn,
-   output RAM_LDn,
-   
-   // Debug stuff
-   output uart_tx_o, 
-   input uart_rx_i,
-   output uart_baud_o,
-   input sim_mode,
-   input [3:0] clock_divider
-   );
-
-   localparam SR_BUF_POOL = 64;   // Uses 1 reg
-   localparam SR_UDP_SM   = 96;   // 64 regs
-   localparam SR_RX_DSP   = 160;  // 16
-   localparam SR_RX_CTRL  = 176;  // 16
-   localparam SR_TIME64   = 192;  //  3
-   localparam SR_SIMTIMER = 198;  //  2
-   localparam SR_TX_DSP   = 208;  // 16
-   localparam SR_TX_CTRL  = 224;  // 16
-
-   // FIFO Sizes, 9 = 512 lines, 10 = 1024, 11 = 2048
-   // all (most?) are 36 bits wide, so 9 is 1 BRAM, 10 is 2, 11 is 4 BRAMs
-   localparam DSP_TX_FIFOSIZE = 10;
-   localparam DSP_RX_FIFOSIZE = 10;
-   localparam ETH_TX_FIFOSIZE = 10;
-   localparam ETH_RX_FIFOSIZE = 11;
-   localparam SERDES_TX_FIFOSIZE = 9;
-   localparam SERDES_RX_FIFOSIZE = 9;  // RX currently doesn't use a fifo?
-   
-   wire [7:0] 	set_addr, set_addr_dsp;
-   wire [31:0] 	set_data, set_data_dsp;
-   wire 	set_stb, set_stb_dsp;
-   
-   wire 	ram_loader_done;
-   wire 	ram_loader_rst, wb_rst, dsp_rst;
-   assign dsp_rst = wb_rst;
-
-   wire [31:0] 	status, status_b0, status_b1, status_b2, status_b3, status_b4, status_b5, status_b6, status_b7;
-   wire 	bus_error, spi_int, i2c_int, pps_int, onetime_int, periodic_int, buffer_int;
-   wire 	proc_int, overrun, underrun, uart_tx_int, uart_rx_int;
-
-   wire [31:0] 	debug_gpio_0, debug_gpio_1;
-   wire [31:0] 	atr_lines;
-
-   wire [31:0] 	debug_rx, debug_mac, debug_mac0, debug_mac1, debug_tx_dsp, debug_txc,
-		debug_serdes0, debug_serdes1, debug_serdes2, debug_rx_dsp, debug_udp, debug_extfifo, debug_extfifo2;
-
-   wire [15:0] 	ser_rx_occ, ser_tx_occ, dsp_rx_occ, dsp_tx_occ, eth_rx_occ, eth_tx_occ, eth_rx_occ2;
-   wire 	ser_rx_full, ser_tx_full, dsp_rx_full, dsp_tx_full, eth_rx_full, eth_tx_full, eth_rx_full2;
-   wire 	ser_rx_empty, ser_tx_empty, dsp_rx_empty, dsp_tx_empty, eth_rx_empty, eth_tx_empty, eth_rx_empty2;
-	
-   wire 	serdes_link_up;
-   wire 	epoch;
-   wire [31:0] 	irq;
-   wire [63:0] 	vita_time;
-   
-   wire 	 run_rx, run_tx;
-   reg 		 run_rx_d1;
-   always @(posedge dsp_clk)
-     run_rx_d1 <= run_rx;
-   
-   // ///////////////////////////////////////////////////////////////////////////////////////////////
-   // Wishbone Single Master INTERCON
-   localparam 	dw = 32;  // Data bus width
-   localparam 	aw = 16;  // Address bus width, for byte addressibility, 16 = 64K byte memory space
-   localparam	sw = 4;   // Select width -- 32-bit data bus with 8-bit granularity.  
-   
-   wire [dw-1:0] m0_dat_o, m0_dat_i;
-   wire [dw-1:0] s0_dat_o, s1_dat_o, s0_dat_i, s1_dat_i, s2_dat_o, s3_dat_o, s2_dat_i, s3_dat_i,
-		 s4_dat_o, s5_dat_o, s4_dat_i, s5_dat_i, s6_dat_o, s7_dat_o, s6_dat_i, s7_dat_i,
-		 s8_dat_o, s9_dat_o, s8_dat_i, s9_dat_i, sa_dat_o, sa_dat_i, sb_dat_i, sb_dat_o,
-		 sc_dat_i, sc_dat_o, sd_dat_i, sd_dat_o, se_dat_i, se_dat_o;
-   wire [aw-1:0] m0_adr,s0_adr,s1_adr,s2_adr,s3_adr,s4_adr,s5_adr,s6_adr,s7_adr,s8_adr,s9_adr,sa_adr,sb_adr,sc_adr, sd_adr, se_adr;
-   wire [sw-1:0] m0_sel,s0_sel,s1_sel,s2_sel,s3_sel,s4_sel,s5_sel,s6_sel,s7_sel,s8_sel,s9_sel,sa_sel,sb_sel,sc_sel, sd_sel, se_sel;
-   wire 	 m0_ack,s0_ack,s1_ack,s2_ack,s3_ack,s4_ack,s5_ack,s6_ack,s7_ack,s8_ack,s9_ack,sa_ack,sb_ack,sc_ack, sd_ack, se_ack;
-   wire 	 m0_stb,s0_stb,s1_stb,s2_stb,s3_stb,s4_stb,s5_stb,s6_stb,s7_stb,s8_stb,s9_stb,sa_stb,sb_stb,sc_stb, sd_stb, se_stb;
-   wire 	 m0_cyc,s0_cyc,s1_cyc,s2_cyc,s3_cyc,s4_cyc,s5_cyc,s6_cyc,s7_cyc,s8_cyc,s9_cyc,sa_cyc,sb_cyc,sc_cyc, sd_cyc, se_cyc;
-   wire 	 m0_err, m0_rty;
-   wire 	 m0_we,s0_we,s1_we,s2_we,s3_we,s4_we,s5_we,s6_we,s7_we,s8_we,s9_we,sa_we,sb_we,sc_we,sd_we, se_we;
-   
-   wb_1master #(.decode_w(6),
-		.s0_addr(6'b0000_00),.s0_mask(6'b100000),
-		.s1_addr(6'b1000_00),.s1_mask(6'b110000),
- 		.s2_addr(6'b1100_00),.s2_mask(6'b111111),
-		.s3_addr(6'b1100_01),.s3_mask(6'b111111),
-		.s4_addr(6'b1100_10),.s4_mask(6'b111111),
-		.s5_addr(6'b1100_11),.s5_mask(6'b111111),
-		.s6_addr(6'b1101_00),.s6_mask(6'b111111),
-		.s7_addr(6'b1101_01),.s7_mask(6'b111111),
-		.s8_addr(6'b1101_10),.s8_mask(6'b111111),
-		.s9_addr(6'b1101_11),.s9_mask(6'b111111),
-		.sa_addr(6'b1110_00),.sa_mask(6'b111111),
-		.sb_addr(6'b1110_01),.sb_mask(6'b111111),
-		.sc_addr(6'b1110_10),.sc_mask(6'b111111),
-		.sd_addr(6'b1110_11),.sd_mask(6'b111111),
-		.se_addr(6'b1111_00),.se_mask(6'b111111),
-		.sf_addr(6'b1111_01),.sf_mask(6'b111111),
-		.dw(dw),.aw(aw),.sw(sw)) wb_1master
-     (.clk_i(wb_clk),.rst_i(wb_rst),       
-      .m0_dat_o(m0_dat_o),.m0_ack_o(m0_ack),.m0_err_o(m0_err),.m0_rty_o(m0_rty),.m0_dat_i(m0_dat_i),
-      .m0_adr_i(m0_adr),.m0_sel_i(m0_sel),.m0_we_i(m0_we),.m0_cyc_i(m0_cyc),.m0_stb_i(m0_stb),
-      .s0_dat_o(s0_dat_o),.s0_adr_o(s0_adr),.s0_sel_o(s0_sel),.s0_we_o	(s0_we),.s0_cyc_o(s0_cyc),.s0_stb_o(s0_stb),
-      .s0_dat_i(s0_dat_i),.s0_ack_i(s0_ack),.s0_err_i(0),.s0_rty_i(0),
-      .s1_dat_o(s1_dat_o),.s1_adr_o(s1_adr),.s1_sel_o(s1_sel),.s1_we_o	(s1_we),.s1_cyc_o(s1_cyc),.s1_stb_o(s1_stb),
-      .s1_dat_i(s1_dat_i),.s1_ack_i(s1_ack),.s1_err_i(0),.s1_rty_i(0),
-      .s2_dat_o(s2_dat_o),.s2_adr_o(s2_adr),.s2_sel_o(s2_sel),.s2_we_o	(s2_we),.s2_cyc_o(s2_cyc),.s2_stb_o(s2_stb),
-      .s2_dat_i(s2_dat_i),.s2_ack_i(s2_ack),.s2_err_i(0),.s2_rty_i(0),
-      .s3_dat_o(s3_dat_o),.s3_adr_o(s3_adr),.s3_sel_o(s3_sel),.s3_we_o	(s3_we),.s3_cyc_o(s3_cyc),.s3_stb_o(s3_stb),
-      .s3_dat_i(s3_dat_i),.s3_ack_i(s3_ack),.s3_err_i(0),.s3_rty_i(0),
-      .s4_dat_o(s4_dat_o),.s4_adr_o(s4_adr),.s4_sel_o(s4_sel),.s4_we_o	(s4_we),.s4_cyc_o(s4_cyc),.s4_stb_o(s4_stb),
-      .s4_dat_i(s4_dat_i),.s4_ack_i(s4_ack),.s4_err_i(0),.s4_rty_i(0),
-      .s5_dat_o(s5_dat_o),.s5_adr_o(s5_adr),.s5_sel_o(s5_sel),.s5_we_o	(s5_we),.s5_cyc_o(s5_cyc),.s5_stb_o(s5_stb),
-      .s5_dat_i(s5_dat_i),.s5_ack_i(s5_ack),.s5_err_i(0),.s5_rty_i(0),
-      .s6_dat_o(s6_dat_o),.s6_adr_o(s6_adr),.s6_sel_o(s6_sel),.s6_we_o	(s6_we),.s6_cyc_o(s6_cyc),.s6_stb_o(s6_stb),
-      .s6_dat_i(s6_dat_i),.s6_ack_i(s6_ack),.s6_err_i(0),.s6_rty_i(0),
-      .s7_dat_o(s7_dat_o),.s7_adr_o(s7_adr),.s7_sel_o(s7_sel),.s7_we_o	(s7_we),.s7_cyc_o(s7_cyc),.s7_stb_o(s7_stb),
-      .s7_dat_i(s7_dat_i),.s7_ack_i(s7_ack),.s7_err_i(0),.s7_rty_i(0),
-      .s8_dat_o(s8_dat_o),.s8_adr_o(s8_adr),.s8_sel_o(s8_sel),.s8_we_o	(s8_we),.s8_cyc_o(s8_cyc),.s8_stb_o(s8_stb),
-      .s8_dat_i(s8_dat_i),.s8_ack_i(s8_ack),.s8_err_i(0),.s8_rty_i(0),
-      .s9_dat_o(s9_dat_o),.s9_adr_o(s9_adr),.s9_sel_o(s9_sel),.s9_we_o	(s9_we),.s9_cyc_o(s9_cyc),.s9_stb_o(s9_stb),
-      .s9_dat_i(s9_dat_i),.s9_ack_i(s9_ack),.s9_err_i(0),.s9_rty_i(0),
-      .sa_dat_o(sa_dat_o),.sa_adr_o(sa_adr),.sa_sel_o(sa_sel),.sa_we_o(sa_we),.sa_cyc_o(sa_cyc),.sa_stb_o(sa_stb),
-      .sa_dat_i(sa_dat_i),.sa_ack_i(sa_ack),.sa_err_i(0),.sa_rty_i(0),
-      .sb_dat_o(sb_dat_o),.sb_adr_o(sb_adr),.sb_sel_o(sb_sel),.sb_we_o(sb_we),.sb_cyc_o(sb_cyc),.sb_stb_o(sb_stb),
-      .sb_dat_i(sb_dat_i),.sb_ack_i(sb_ack),.sb_err_i(0),.sb_rty_i(0),
-      .sc_dat_o(sc_dat_o),.sc_adr_o(sc_adr),.sc_sel_o(sc_sel),.sc_we_o(sc_we),.sc_cyc_o(sc_cyc),.sc_stb_o(sc_stb),
-      .sc_dat_i(sc_dat_i),.sc_ack_i(sc_ack),.sc_err_i(0),.sc_rty_i(0),
-      .sd_dat_o(sd_dat_o),.sd_adr_o(sd_adr),.sd_sel_o(sd_sel),.sd_we_o(sd_we),.sd_cyc_o(sd_cyc),.sd_stb_o(sd_stb),
-      .sd_dat_i(sd_dat_i),.sd_ack_i(sd_ack),.sd_err_i(0),.sd_rty_i(0),
-      .se_dat_o(se_dat_o),.se_adr_o(se_adr),.se_sel_o(se_sel),.se_we_o(se_we),.se_cyc_o(se_cyc),.se_stb_o(se_stb),
-      .se_dat_i(se_dat_i),.se_ack_i(se_ack),.se_err_i(0),.se_rty_i(0),
-      .sf_dat_i(0),.sf_ack_i(0),.sf_err_i(0),.sf_rty_i(0)  );
-   
-   //////////////////////////////////////////////////////////////////////////////////////////
-   // Reset Controller
-   system_control sysctrl (.wb_clk_i(wb_clk), // .por_i(por),
-			   .ram_loader_rst_o(ram_loader_rst),
-			   .wb_rst_o(wb_rst),
-			   .ram_loader_done_i(ram_loader_done));
-
-   assign 	 config_success = ram_loader_done;
-   reg 		 takeover = 0;
-
-   wire 	 cpld_start_int, cpld_mode_int, cpld_done_int;
-   
-   always @(posedge wb_clk)
-     if(ram_loader_done)
-       takeover = 1;
-   assign 	 cpld_misc = ~takeover;
-
-   wire 	 sd_clk, sd_csn, sd_mosi, sd_miso;
-   
-   assign 	 sd_miso = cpld_din;
-   assign 	 cpld_start = takeover ? sd_clk	: cpld_start_int;
-   assign 	 cpld_mode = takeover ? sd_csn : cpld_mode_int;
-   assign 	 cpld_done = takeover ? sd_mosi : cpld_done_int;
-   
-   // ///////////////////////////////////////////////////////////////////
-   // RAM Loader
-
-   wire [31:0] 	 ram_loader_dat, if_dat;
-   wire [15:0] 	 ram_loader_adr;
-   wire [14:0] 	 if_adr;
-   wire [3:0] 	 ram_loader_sel;
-   wire 	 ram_loader_stb, ram_loader_we;
-   wire 	 iwb_ack, iwb_stb;
-   ram_loader #(.AWIDTH(16),.RAM_SIZE(RAM_SIZE))
-     ram_loader (.wb_clk(wb_clk),.dsp_clk(dsp_clk),.ram_loader_rst(ram_loader_rst),
-		 .wb_dat(ram_loader_dat),.wb_adr(ram_loader_adr),
-		 .wb_stb(ram_loader_stb),.wb_sel(ram_loader_sel),
-		 .wb_we(ram_loader_we),
-		 .ram_loader_done(ram_loader_done),
-		 // CPLD Interface
-		 .cpld_clk(cpld_clk),
-		 .cpld_din(cpld_din),
-		 .cpld_start(cpld_start_int),
-		 .cpld_mode(cpld_mode_int),
-		 .cpld_done(cpld_done_int),
-		 .cpld_detached(cpld_detached));
-   
-   // /////////////////////////////////////////////////////////////////////////
-   // Processor
-   aeMB_core_BE #(.ISIZ(16),.DSIZ(16),.MUL(0),.BSF(1))
-     aeMB (.sys_clk_i(wb_clk), .sys_rst_i(wb_rst),
-	   // Instruction Wishbone bus to I-RAM
-	   .if_adr(if_adr),
-	   .if_dat(if_dat),
-	   // Data Wishbone bus to system bus fabric
-	   .dwb_we_o(m0_we),.dwb_stb_o(m0_stb),.dwb_dat_o(m0_dat_i),.dwb_adr_o(m0_adr),
-	   .dwb_dat_i(m0_dat_o),.dwb_ack_i(m0_ack),.dwb_sel_o(m0_sel),.dwb_cyc_o(m0_cyc),
-	   // Interrupts and exceptions
-	   .sys_int_i(proc_int),.sys_exc_i(bus_error) );
-   
-   assign 	 bus_error = m0_err | m0_rty;
-   
-   // /////////////////////////////////////////////////////////////////////////
-   // Dual Ported RAM -- D-Port is Slave #0 on main Wishbone
-   // I-port connects directly to processor and ram loader
-
-   wire 	 flush_icache;
-   ram_harvard #(.AWIDTH(15),.RAM_SIZE(RAM_SIZE),.ICWIDTH(7),.DCWIDTH(6))
-     sys_ram(.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),
-	     
-	     .ram_loader_adr_i(ram_loader_adr[14:0]), .ram_loader_dat_i(ram_loader_dat),
-	     .ram_loader_stb_i(ram_loader_stb), .ram_loader_sel_i(ram_loader_sel),
-	     .ram_loader_we_i(ram_loader_we),
-	     .ram_loader_done_i(ram_loader_done),
-	     
-	     .if_adr(if_adr), 
-	     .if_data(if_dat), 
-	     
-	     .dwb_adr_i(s0_adr[14:0]), .dwb_dat_i(s0_dat_o), .dwb_dat_o(s0_dat_i),
-	     .dwb_we_i(s0_we), .dwb_ack_o(s0_ack), .dwb_stb_i(s0_stb), .dwb_sel_i(s0_sel),
-	     .flush_icache(flush_icache));
-   
-   setting_reg #(.my_addr(7)) sr_icache (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
-					 .in(set_data),.out(),.changed(flush_icache));
-
-   // /////////////////////////////////////////////////////////////////////////
-   // Buffer Pool, slave #1
-   wire 	 rd0_ready_i, rd0_ready_o;
-   wire 	 rd1_ready_i, rd1_ready_o;
-   wire 	 rd2_ready_i, rd2_ready_o;
-   wire 	 rd3_ready_i, rd3_ready_o;
-   wire [3:0] 	 rd0_flags, rd1_flags, rd2_flags, rd3_flags;
-   wire [31:0] 	 rd0_dat, rd1_dat, rd2_dat, rd3_dat;
-
-   wire 	 wr0_ready_i, wr0_ready_o;
-   wire 	 wr1_ready_i, wr1_ready_o;
-   wire 	 wr2_ready_i, wr2_ready_o;
-   wire 	 wr3_ready_i, wr3_ready_o;
-   wire [3:0] 	 wr0_flags, wr1_flags, wr2_flags, wr3_flags;
-   wire [31:0] 	 wr0_dat, wr1_dat, wr2_dat, wr3_dat;
-   
-   buffer_pool #(.BUF_SIZE(9), .SET_ADDR(SR_BUF_POOL)) buffer_pool
-     (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),
-      .wb_we_i(s1_we),.wb_stb_i(s1_stb),.wb_adr_i(s1_adr),.wb_dat_i(s1_dat_o),   
-      .wb_dat_o(s1_dat_i),.wb_ack_o(s1_ack),.wb_err_o(),.wb_rty_o(),
-   
-      .stream_clk(dsp_clk), .stream_rst(dsp_rst),
-      .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
-      .status(status),.sys_int_o(buffer_int),
-
-      .s0(status_b0),.s1(status_b1),.s2(status_b2),.s3(status_b3),
-      .s4(status_b4),.s5(status_b5),.s6(status_b6),.s7(status_b7),
-
-      // Write Interfaces
-      .wr0_data_i(wr0_dat), .wr0_flags_i(wr0_flags), .wr0_ready_i(wr0_ready_i), .wr0_ready_o(wr0_ready_o),
-      .wr1_data_i(wr1_dat), .wr1_flags_i(wr1_flags), .wr1_ready_i(wr1_ready_i), .wr1_ready_o(wr1_ready_o),
-      .wr2_data_i(wr2_dat), .wr2_flags_i(wr2_flags), .wr2_ready_i(wr2_ready_i), .wr2_ready_o(wr2_ready_o),
-      .wr3_data_i(wr3_dat), .wr3_flags_i(wr3_flags), .wr3_ready_i(wr3_ready_i), .wr3_ready_o(wr3_ready_o),
-      // Read Interfaces
-      .rd0_data_o(rd0_dat), .rd0_flags_o(rd0_flags), .rd0_ready_i(rd0_ready_i), .rd0_ready_o(rd0_ready_o),
-      .rd1_data_o(rd1_dat), .rd1_flags_o(rd1_flags), .rd1_ready_i(rd1_ready_i), .rd1_ready_o(rd1_ready_o),
-      .rd2_data_o(rd2_dat), .rd2_flags_o(rd2_flags), .rd2_ready_i(rd2_ready_i), .rd2_ready_o(rd2_ready_o),
-      .rd3_data_o(rd3_dat), .rd3_flags_o(rd3_flags), .rd3_ready_i(rd3_ready_i), .rd3_ready_o(rd3_ready_o)
-      );
-
-   wire [31:0] 	 status_enc;
-   priority_enc priority_enc (.in({16'b0,status[15:0]}), .out(status_enc));
-   
-   // /////////////////////////////////////////////////////////////////////////
-   // SPI -- Slave #2
-   spi_top shared_spi
-     (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),.wb_adr_i(s2_adr[4:0]),.wb_dat_i(s2_dat_o),
-      .wb_dat_o(s2_dat_i),.wb_sel_i(s2_sel),.wb_we_i(s2_we),.wb_stb_i(s2_stb),
-      .wb_cyc_i(s2_cyc),.wb_ack_o(s2_ack),.wb_err_o(),.wb_int_o(spi_int),
-      .ss_pad_o({sen_tx_db,sen_tx_adc,sen_tx_dac,sen_rx_db,sen_rx_adc,sen_rx_dac,sen_dac,sen_clk}),
-      .sclk_pad_o(sclk),.mosi_pad_o(mosi),.miso_pad_i(miso) );
-
-   // /////////////////////////////////////////////////////////////////////////
-   // I2C -- Slave #3
-   i2c_master_top #(.ARST_LVL(1)) 
-     i2c (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),.arst_i(1'b0), 
-	  .wb_adr_i(s3_adr[4:2]),.wb_dat_i(s3_dat_o[7:0]),.wb_dat_o(s3_dat_i[7:0]),
-	  .wb_we_i(s3_we),.wb_stb_i(s3_stb),.wb_cyc_i(s3_cyc),
-	  .wb_ack_o(s3_ack),.wb_inta_o(i2c_int),
-	  .scl_pad_i(scl_pad_i),.scl_pad_o(scl_pad_o),.scl_padoen_o(scl_pad_oen_o),
-	  .sda_pad_i(sda_pad_i),.sda_pad_o(sda_pad_o),.sda_padoen_o(sda_pad_oen_o) );
-
-   assign 	 s3_dat_i[31:8] = 24'd0;
-   
-   // /////////////////////////////////////////////////////////////////////////
-   // GPIOs -- Slave #4
-   nsgpio nsgpio(.clk_i(wb_clk),.rst_i(wb_rst),
-		 .cyc_i(s4_cyc),.stb_i(s4_stb),.adr_i(s4_adr[3:0]),.we_i(s4_we),
-		 .dat_i(s4_dat_o),.dat_o(s4_dat_i),.ack_o(s4_ack),
-		 .atr(atr_lines),.debug_0(debug_gpio_0),.debug_1(debug_gpio_1),
-		 .gpio({io_tx,io_rx}) );
-
-   // /////////////////////////////////////////////////////////////////////////
-   // Buffer Pool Status -- Slave #5   
-   
-   reg [31:0] 	 cycle_count;
-   always @(posedge wb_clk)
-     if(wb_rst)
-       cycle_count <= 0;
-     else
-       cycle_count <= cycle_count + 1;
-
-   //compatibility number -> increment when the fpga has been sufficiently altered
-   localparam compat_num = 32'd3;
-
-   wb_readback_mux buff_pool_status
-     (.wb_clk_i(wb_clk), .wb_rst_i(wb_rst), .wb_stb_i(s5_stb),
-      .wb_adr_i(s5_adr), .wb_dat_o(s5_dat_i), .wb_ack_o(s5_ack),
-      
-      .word00(status_b0),.word01(status_b1),.word02(status_b2),.word03(status_b3),
-      .word04(status_b4),.word05(status_b5),.word06(status_b6),.word07(status_b7),
-      .word08(status),.word09({sim_mode,27'b0,clock_divider[3:0]}),.word10(vita_time[63:32]),
-      .word11(vita_time[31:0]),.word12(compat_num),.word13(irq),.word14(status_enc),.word15(cycle_count)
-      );
-
-   // /////////////////////////////////////////////////////////////////////////
-   // Ethernet MAC  Slave #6
-
-   wire [18:0] 	 rx_f19_data, tx_f19_data;
-   wire 	 rx_f19_src_rdy, rx_f19_dst_rdy, rx_f36_src_rdy, rx_f36_dst_rdy;
-   
-   simple_gemac_wrapper19 #(.RXFIFOSIZE(11), .TXFIFOSIZE(6)) simple_gemac_wrapper19
-     (.clk125(clk_to_mac),  .reset(wb_rst),
-      .GMII_GTX_CLK(GMII_GTX_CLK), .GMII_TX_EN(GMII_TX_EN),  
-      .GMII_TX_ER(GMII_TX_ER), .GMII_TXD(GMII_TXD),
-      .GMII_RX_CLK(GMII_RX_CLK), .GMII_RX_DV(GMII_RX_DV),  
-      .GMII_RX_ER(GMII_RX_ER), .GMII_RXD(GMII_RXD),
-      .sys_clk(dsp_clk),
-      .rx_f19_data(rx_f19_data), .rx_f19_src_rdy(rx_f19_src_rdy), .rx_f19_dst_rdy(rx_f19_dst_rdy),
-      .tx_f19_data(tx_f19_data), .tx_f19_src_rdy(tx_f19_src_rdy), .tx_f19_dst_rdy(tx_f19_dst_rdy),
-      .wb_clk(wb_clk), .wb_rst(wb_rst), .wb_stb(s6_stb), .wb_cyc(s6_cyc), .wb_ack(s6_ack),
-      .wb_we(s6_we), .wb_adr(s6_adr), .wb_dat_i(s6_dat_o), .wb_dat_o(s6_dat_i),
-      .mdio(MDIO), .mdc(MDC),
-      .debug(debug_mac));
-
-   wire [35:0] 	 udp_tx_data, udp_rx_data;
-   wire 	 udp_tx_src_rdy, udp_tx_dst_rdy, udp_rx_src_rdy, udp_rx_dst_rdy;
-   
-   udp_wrapper #(.BASE(SR_UDP_SM)) udp_wrapper
-     (.clk(dsp_clk), .reset(dsp_rst), .clear(0),
-      .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
-      .rx_f19_data(rx_f19_data), .rx_f19_src_rdy_i(rx_f19_src_rdy), .rx_f19_dst_rdy_o(rx_f19_dst_rdy),
-      .tx_f19_data(tx_f19_data), .tx_f19_src_rdy_o(tx_f19_src_rdy), .tx_f19_dst_rdy_i(tx_f19_dst_rdy),
-      .rx_f36_data(udp_rx_data), .rx_f36_src_rdy_o(udp_rx_src_rdy), .rx_f36_dst_rdy_i(udp_rx_dst_rdy),
-      .tx_f36_data(udp_tx_data), .tx_f36_src_rdy_i(udp_tx_src_rdy), .tx_f36_dst_rdy_o(udp_tx_dst_rdy),
-      .debug(debug_udp) );
-
-   wire [35:0] 	 tx_err_data, udp1_tx_data;
-   wire 	 tx_err_src_rdy, tx_err_dst_rdy, udp1_tx_src_rdy, udp1_tx_dst_rdy;
-   
-   fifo_cascade #(.WIDTH(36), .SIZE(ETH_TX_FIFOSIZE)) tx_eth_fifo
-     (.clk(dsp_clk), .reset(dsp_rst), .clear(0),
-      .datain({rd2_flags,rd2_dat}), .src_rdy_i(rd2_ready_o), .dst_rdy_o(rd2_ready_i),
-      .dataout(udp1_tx_data), .src_rdy_o(udp1_tx_src_rdy), .dst_rdy_i(udp1_tx_dst_rdy));
-
-   fifo36_mux #(.prio(0)) mux_err_stream
-     (.clk(dsp_clk), .reset(dsp_reset), .clear(0),
-      .data0_i(udp1_tx_data), .src0_rdy_i(udp1_tx_src_rdy), .dst0_rdy_o(udp1_tx_dst_rdy),
-      .data1_i(tx_err_data), .src1_rdy_i(tx_err_src_rdy), .dst1_rdy_o(tx_err_dst_rdy),
-      .data_o(udp_tx_data), .src_rdy_o(udp_tx_src_rdy), .dst_rdy_i(udp_tx_dst_rdy));
-   
-   fifo_cascade #(.WIDTH(36), .SIZE(ETH_RX_FIFOSIZE)) rx_eth_fifo
-     (.clk(dsp_clk), .reset(dsp_rst), .clear(0),
-      .datain(udp_rx_data), .src_rdy_i(udp_rx_src_rdy), .dst_rdy_o(udp_rx_dst_rdy),
-      .dataout({wr2_flags,wr2_dat}), .src_rdy_o(wr2_ready_i), .dst_rdy_i(wr2_ready_o));
-   
-   // /////////////////////////////////////////////////////////////////////////
-   // Settings Bus -- Slave #7
-   settings_bus settings_bus
-     (.wb_clk(wb_clk),.wb_rst(wb_rst),.wb_adr_i(s7_adr),.wb_dat_i(s7_dat_o),
-      .wb_stb_i(s7_stb),.wb_we_i(s7_we),.wb_ack_o(s7_ack),
-      .strobe(set_stb),.addr(set_addr),.data(set_data));
-   
-   assign 	 s7_dat_i = 32'd0;
-
-   settings_bus_crossclock settings_bus_crossclock
-     (.clk_i(wb_clk), .rst_i(wb_rst), .set_stb_i(set_stb), .set_addr_i(set_addr), .set_data_i(set_data),
-      .clk_o(dsp_clk), .rst_o(dsp_rst), .set_stb_o(set_stb_dsp), .set_addr_o(set_addr_dsp), .set_data_o(set_data_dsp));
-   
-   // Output control lines
-   wire [7:0] 	 clock_outs, serdes_outs, adc_outs;
-   assign 	 {clock_ready, clk_en[1:0], clk_sel[1:0]} = clock_outs[4:0];
-   assign 	 {ser_enable, ser_prbsen, ser_loopen, ser_rx_en} = serdes_outs[3:0];
-   assign 	 {adc_oe_a, adc_on_a, adc_oe_b, adc_on_b } = adc_outs[3:0];
-
-   wire 	 phy_reset;
-   assign 	 PHY_RESETn = ~phy_reset;
-   
-   setting_reg #(.my_addr(0),.width(8)) sr_clk (.clk(wb_clk),.rst(wb_rst),.strobe(s7_ack),.addr(set_addr),
-				      .in(set_data),.out(clock_outs),.changed());
-   setting_reg #(.my_addr(1),.width(8)) sr_ser (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
-				      .in(set_data),.out(serdes_outs),.changed());
-   setting_reg #(.my_addr(2),.width(8)) sr_adc (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
-				      .in(set_data),.out(adc_outs),.changed());
-   setting_reg #(.my_addr(4),.width(1)) sr_phy (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
-				      .in(set_data),.out(phy_reset),.changed());
-
-   // /////////////////////////////////////////////////////////////////////////
-   //  LEDS
-   //    register 8 determines whether leds are controlled by SW or not
-   //    1 = controlled by HW, 0 = by SW
-   //    In Rev3 there are only 6 leds, and the highest one is on the ETH connector
-   
-   wire [7:0] 	 led_src, led_sw;
-   wire [7:0] 	 led_hw = {run_tx, run_rx, clk_status, serdes_link_up, 1'b0};
-   
-   setting_reg #(.my_addr(3),.width(8)) sr_led (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
-				      .in(set_data),.out(led_sw),.changed());
-
-   setting_reg #(.my_addr(8),.width(8), .at_reset(8'b0001_1110)) 
-   sr_led_src (.clk(wb_clk),.rst(wb_rst), .strobe(set_stb),.addr(set_addr), .in(set_data),.out(led_src),.changed());
-
-   assign 	 leds = (led_src & led_hw) | (~led_src & led_sw);
-   
-   // /////////////////////////////////////////////////////////////////////////
-   // Interrupt Controller, Slave #8
-
-   // Pass interrupts on dsp_clk to wb_clk.  These need edge triggering in the pic
-   wire 	 underrun_wb, overrun_wb, pps_wb;
-
-   oneshot_2clk underrun_1s (.clk_in(dsp_clk), .in(underrun), .clk_out(wb_clk), .out(underrun_wb));
-   oneshot_2clk overrun_1s (.clk_in(dsp_clk), .in(overrun), .clk_out(wb_clk), .out(overrun_wb));
-   oneshot_2clk pps_1s (.clk_in(dsp_clk), .in(pps_int), .clk_out(wb_clk), .out(pps_wb));
-   
-   assign irq= {{8'b0},
-		{8'b0},
-		{3'b0, periodic_int, clk_status, serdes_link_up, uart_tx_int, uart_rx_int},
-		{pps_wb,overrun_wb,underrun_wb,PHY_INTn,i2c_int,spi_int,onetime_int,buffer_int}};
-   
-   pic pic(.clk_i(wb_clk),.rst_i(wb_rst),.cyc_i(s8_cyc),.stb_i(s8_stb),.adr_i(s8_adr[4:2]),
-	   .we_i(s8_we),.dat_i(s8_dat_o),.dat_o(s8_dat_i),.ack_o(s8_ack),.int_o(proc_int),
-	   .irq(irq) );
- 	 
-   // /////////////////////////////////////////////////////////////////////////
-   // Master Timer, Slave #9
-
-   // No longer used, replaced with simple_timer below
-   assign s9_ack = 0;
-   
-   // /////////////////////////////////////////////////////////////////////////
-   //  Simple Timer interrupts
-   
-   simple_timer #(.BASE(SR_SIMTIMER)) simple_timer
-     (.clk(wb_clk), .reset(wb_rst),
-      .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
-      .onetime_int(onetime_int), .periodic_int(periodic_int));
-   
-   // /////////////////////////////////////////////////////////////////////////
-   // UART, Slave #10
-
-   simple_uart #(.TXDEPTH(3),.RXDEPTH(3)) uart  // depth of 3 is 128 entries
-     (.clk_i(wb_clk),.rst_i(wb_rst),
-      .we_i(sa_we),.stb_i(sa_stb),.cyc_i(sa_cyc),.ack_o(sa_ack),
-      .adr_i(sa_adr[4:2]),.dat_i(sa_dat_o),.dat_o(sa_dat_i),
-      .rx_int_o(uart_rx_int),.tx_int_o(uart_tx_int),
-      .tx_o(uart_tx_o),.rx_i(uart_rx_i),.baud_o(uart_baud_o));
-   
-   // /////////////////////////////////////////////////////////////////////////
-   // ATR Controller, Slave #11
-
-   atr_controller atr_controller
-     (.clk_i(wb_clk),.rst_i(wb_rst),
-      .adr_i(sb_adr[5:0]),.sel_i(sb_sel),.dat_i(sb_dat_o),.dat_o(sb_dat_i),
-      .we_i(sb_we),.stb_i(sb_stb),.cyc_i(sb_cyc),.ack_o(sb_ack),
-      .run_rx(run_rx_d1),.run_tx(run_tx),.ctrl_lines(atr_lines) );
-   
-   // //////////////////////////////////////////////////////////////////////////
-   // Time Sync, Slave #12 
-
-   // No longer used, see time_64bit.  Still need to handle mimo time, though
-   assign sc_ack = 0;
-   
-   // /////////////////////////////////////////////////////////////////////////
-   // SD Card Reader / Writer, Slave #13
-
-   sd_spi_wb sd_spi_wb
-     (.clk(wb_clk),.rst(wb_rst),
-      .sd_clk(sd_clk),.sd_csn(sd_csn),.sd_mosi(sd_mosi),.sd_miso(sd_miso),
-      .wb_cyc_i(sd_cyc),.wb_stb_i(sd_stb),.wb_we_i(sd_we),
-      .wb_adr_i(sd_adr[3:2]),.wb_dat_i(sd_dat_o[7:0]),.wb_dat_o(sd_dat_i[7:0]),
-      .wb_ack_o(sd_ack) );
-
-   assign sd_dat_i[31:8] = 0;
-
-   // /////////////////////////////////////////////////////////////////////////
-   // DSP RX
-   wire [31:0] 	 sample_rx, sample_tx;
-   wire 	 strobe_rx, strobe_tx;
-   wire 	 rx_dst_rdy, rx_src_rdy, rx1_dst_rdy, rx1_src_rdy;
-   wire [99:0] 	 rx_data;
-   wire [35:0] 	 rx1_data;
-   
-   dsp_core_rx #(.BASE(SR_RX_DSP)) dsp_core_rx
-     (.clk(dsp_clk),.rst(dsp_rst),
-      .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
-      .adc_a(adc_a),.adc_ovf_a(adc_ovf_a),.adc_b(adc_b),.adc_ovf_b(adc_ovf_b),
-      .sample(sample_rx), .run(run_rx_d1), .strobe(strobe_rx),
-      .debug(debug_rx_dsp) );
-
-   wire [31:0] 	 vrc_debug;
-   wire 	 clear_rx;
-   
-   setting_reg #(.my_addr(SR_RX_CTRL+3)) sr_clear
-     (.clk(dsp_clk),.rst(dsp_rst),
-      .strobe(set_stb_dsp),.addr(set_addr_dsp),.in(set_data_dsp),
-      .out(),.changed(clear_rx));
-
-   vita_rx_control #(.BASE(SR_RX_CTRL), .WIDTH(32)) vita_rx_control
-     (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx),
-      .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
-      .vita_time(vita_time), .overrun(overrun),
-      .sample(sample_rx), .run(run_rx), .strobe(strobe_rx),
-      .sample_fifo_o(rx_data), .sample_fifo_dst_rdy_i(rx_dst_rdy), .sample_fifo_src_rdy_o(rx_src_rdy),
-      .debug_rx(vrc_debug));
-
-   wire [3:0] 	 vita_state;
-   
-   vita_rx_framer #(.BASE(SR_RX_CTRL), .MAXCHAN(1)) vita_rx_framer
-     (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx),
-      .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
-      .sample_fifo_i(rx_data), .sample_fifo_dst_rdy_o(rx_dst_rdy), .sample_fifo_src_rdy_i(rx_src_rdy),
-      .data_o(rx1_data), .dst_rdy_i(rx1_dst_rdy), .src_rdy_o(rx1_src_rdy),
-      .fifo_occupied(), .fifo_full(), .fifo_empty(),
-      .debug_rx(vita_state) );
-
-   fifo_cascade #(.WIDTH(36), .SIZE(DSP_RX_FIFOSIZE)) rx_fifo_cascade
-     (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx),
-      .datain(rx1_data), .src_rdy_i(rx1_src_rdy), .dst_rdy_o(rx1_dst_rdy),
-      .dataout({wr1_flags,wr1_dat}), .src_rdy_o(wr1_ready_i), .dst_rdy_i(wr1_ready_o));
-
-   // ///////////////////////////////////////////////////////////////////////////////////
-   // DSP TX
-
-   wire [35:0] 	 tx_data;
-   wire 	 tx_src_rdy, tx_dst_rdy;
-   wire [31:0] 	 debug_vt;
-   wire 	 clear_tx;
-
-   setting_reg #(.my_addr(SR_TX_CTRL+1)) sr_clear_tx
-     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
-      .in(set_data),.out(),.changed(clear_tx));
-
-   ext_fifo #(.EXT_WIDTH(18),.INT_WIDTH(36),.RAM_DEPTH(19),.FIFO_DEPTH(19)) 
-     ext_fifo_i1
-       (.int_clk(dsp_clk),
-	.ext_clk(clk_to_mac),
-	.rst(dsp_rst | clear_tx),
-	.RAM_D_pi(RAM_D_pi),
-	.RAM_D_po(RAM_D_po),
-	.RAM_D_poe(RAM_D_poe),
-	.RAM_A(RAM_A),
-	.RAM_WEn(RAM_WEn),
-	.RAM_CENn(RAM_CENn),
-	.RAM_LDn(RAM_LDn),
-	.RAM_OEn(RAM_OEn),
-	.RAM_CE1n(RAM_CE1n),
-	.datain({rd1_flags[3:2],rd1_dat[31:16],rd1_flags[1:0],rd1_dat[15:0]}),
-	.src_rdy_i(rd1_ready_o),
-	.dst_rdy_o(rd1_ready_i),
-	.dataout({tx_data[35:34],tx_data[31:16],tx_data[33:32],tx_data[15:0]}),
-	.src_rdy_o(tx_src_rdy),
-	.dst_rdy_i(tx_dst_rdy),
-	.debug(debug_extfifo),
-	.debug2(debug_extfifo2) );
-
-   vita_tx_chain #(.BASE_CTRL(SR_TX_CTRL), .BASE_DSP(SR_TX_DSP), 
-		   .REPORT_ERROR(1), .DO_FLOW_CONTROL(1),
-		   .PROT_ENG_FLAGS(1), .USE_TRANS_HEADER(1)) 
-   vita_tx_chain
-     (.clk(dsp_clk), .reset(dsp_rst),
-      .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
-      .vita_time(vita_time),
-      .tx_data_i(tx_data), .tx_src_rdy_i(tx_src_rdy), .tx_dst_rdy_o(tx_dst_rdy),
-      .err_data_o(tx_err_data), .err_src_rdy_o(tx_err_src_rdy), .err_dst_rdy_i(tx_err_dst_rdy),
-      .dac_a(dac_a),.dac_b(dac_b),
-      .underrun(underrun), .run(run_tx),
-      .debug(debug_vt));
-   
-   // ///////////////////////////////////////////////////////////////////////////////////
-   // SERDES
-
-   serdes #(.TXFIFOSIZE(SERDES_TX_FIFOSIZE),.RXFIFOSIZE(SERDES_RX_FIFOSIZE)) serdes
-     (.clk(dsp_clk),.rst(dsp_rst),
-      .ser_tx_clk(ser_tx_clk),.ser_t(ser_t),.ser_tklsb(ser_tklsb),.ser_tkmsb(ser_tkmsb),
-      .rd_dat_i(rd0_dat),.rd_flags_i(rd0_flags),.rd_ready_o(rd0_ready_i),.rd_ready_i(rd0_ready_o),
-      .ser_rx_clk(ser_rx_clk),.ser_r(ser_r),.ser_rklsb(ser_rklsb),.ser_rkmsb(ser_rkmsb),
-      .wr_dat_o(wr0_dat),.wr_flags_o(wr0_flags),.wr_ready_o(wr0_ready_i),.wr_ready_i(wr0_ready_o),
-      .tx_occupied(ser_tx_occ),.tx_full(ser_tx_full),.tx_empty(ser_tx_empty),
-      .rx_occupied(ser_rx_occ),.rx_full(ser_rx_full),.rx_empty(ser_rx_empty),
-      .serdes_link_up(serdes_link_up),.debug0(debug_serdes0), .debug1(debug_serdes1) );
-
-   assign RAM_CLK = clk_to_mac;
-   
-   // /////////////////////////////////////////////////////////////////////////
-   // VITA Timing
-
-   time_64bit #(.TICKS_PER_SEC(32'd100000000),.BASE(SR_TIME64)) time_64bit
-     (.clk(dsp_clk), .rst(dsp_rst), .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
-      .pps(pps_in), .vita_time(vita_time), .pps_int(pps_int));
-   
-   // /////////////////////////////////////////////////////////////////////////////////////////
-   // Debug Pins
-  
-   assign debug_clk = 2'b00; // {dsp_clk, clk_to_mac};
-   assign debug = 32'd0; // debug_extfifo;
-   assign debug_gpio_0 = 32'd0;
-   assign debug_gpio_1 = 32'd0;
-   
-endmodule // u2_core
diff --git a/fpga/usrp2/top/u2_rev3/u2_rev3.ucf b/fpga/usrp2/top/u2_rev3/u2_rev3.ucf
index 6e0caedd5..8017f61ff 100644
--- a/fpga/usrp2/top/u2_rev3/u2_rev3.ucf
+++ b/fpga/usrp2/top/u2_rev3/u2_rev3.ucf
@@ -40,10 +40,10 @@ NET "debug_clk[0]"  LOC = "N4"  ;
 NET "debug_clk[1]"  LOC = "M1"  ;
 NET "uart_tx_o"  LOC = "C7"  ;
 NET "uart_rx_i"  LOC = "A3"  ;
-NET "exp_pps_in_p"  LOC = "V3"  ; 
-NET "exp_pps_in_n"  LOC = "V4"  ; 
-NET "exp_pps_out_p"  LOC = "V1"  ; 
-NET "exp_pps_out_n"  LOC = "V2"  ; 
+NET "exp_time_in_p"  LOC = "V3"  ; 
+NET "exp_time_in_n"  LOC = "V4"  ; 
+NET "exp_time_out_p"  LOC = "V1"  ; 
+NET "exp_time_out_n"  LOC = "V2"  ; 
 NET "GMII_COL"  LOC = "U16"  ; 
 NET "GMII_CRS"  LOC = "U17"  ; 
 NET "GMII_TXD[0]"  LOC = "W14"  |IOSTANDARD = LVCMOS25  |DRIVE = 12  |SLEW = FAST ;
diff --git a/fpga/usrp2/top/u2_rev3/u2_rev3.v b/fpga/usrp2/top/u2_rev3/u2_rev3.v
index 4f7f9bf1a..f2bba6c50 100644
--- a/fpga/usrp2/top/u2_rev3/u2_rev3.v
+++ b/fpga/usrp2/top/u2_rev3/u2_rev3.v
@@ -11,10 +11,10 @@ module u2_rev3
    input uart_rx_i,
    
    // Expansion
-   input exp_pps_in_p, // Diff
-   input exp_pps_in_n, // Diff
-   output exp_pps_out_p, // Diff 
-   output exp_pps_out_n, // Diff 
+   input exp_time_in_p, // Diff
+   input exp_time_in_n, // Diff
+   output exp_time_out_p, // Diff 
+   output exp_time_out_n, // Diff 
    
    // GMII
    //   GMII-CTRL
@@ -181,13 +181,13 @@ module u2_rev3
    wire 	cpld_clock_buf;
    BUFG cpld_clock_BUF (.O(cpld_clock_buf),.I(cpld_clock));
    
-   wire 	exp_pps_in;
-   IBUFDS exp_pps_in_pin (.O(exp_pps_in),.I(exp_pps_in_p),.IB(exp_pps_in_n));
-   defparam 	exp_pps_in_pin.IOSTANDARD = "LVDS_25";
+   wire 	exp_time_in;
+   IBUFDS exp_time_in_pin (.O(exp_time_in),.I(exp_time_in_p),.IB(exp_time_in_n));
+   defparam 	exp_time_in_pin.IOSTANDARD = "LVDS_25";
    
-   wire 	exp_pps_out;
-   OBUFDS exp_pps_out_pin (.O(exp_pps_out_p),.OB(exp_pps_out_n),.I(exp_pps_out));
-   defparam 	exp_pps_out_pin.IOSTANDARD = "LVDS_25";
+   wire 	exp_time_out;
+   OBUFDS exp_time_out_pin (.O(exp_time_out_p),.OB(exp_time_out_n),.I(exp_time_out));
+   defparam 	exp_time_out_pin.IOSTANDARD = "LVDS_25";
 
    reg [5:0] 	clock_ready_d;
    always @(posedge clk_fpga)
@@ -480,8 +480,8 @@ module u2_rev3
 	     .leds		(leds_int),
 	     .debug		(debug[31:0]),
 	     .debug_clk		(debug_clk[1:0]),
-	     .exp_pps_in	(exp_pps_in),
-	     .exp_pps_out	(exp_pps_out),
+	     .exp_time_in	(exp_time_in),
+	     .exp_time_out	(exp_time_out),
 	     .GMII_COL		(GMII_COL),
 	     .GMII_CRS		(GMII_CRS),
 	     .GMII_TXD		(GMII_TXD_unreg[7:0]),
diff --git a/fpga/usrp2/top/u2plus/u2plus.v b/fpga/usrp2/top/u2plus/u2plus.v
index 5facca298..c0140e989 100644
--- a/fpga/usrp2/top/u2plus/u2plus.v
+++ b/fpga/usrp2/top/u2plus/u2plus.v
@@ -357,8 +357,8 @@ module u2plus
 		     .leds		(leds_int),
 		     .debug		(debug[31:0]),
 		     .debug_clk		(debug_clk[1:0]),
-		     .exp_pps_in	(exp_time_in),
-		     .exp_pps_out	(exp_time_out),
+		     .exp_time_in	(exp_time_in),
+		     .exp_time_out	(exp_time_out),
 		     .GMII_COL		(GMII_COL),
 		     .GMII_CRS		(GMII_CRS),
 		     .GMII_TXD		(GMII_TXD_unreg[7:0]),
diff --git a/fpga/usrp2/top/u2plus/u2plus_core.v b/fpga/usrp2/top/u2plus/u2plus_core.v
index 8426826e2..4e0b190ef 100644
--- a/fpga/usrp2/top/u2plus/u2plus_core.v
+++ b/fpga/usrp2/top/u2plus/u2plus_core.v
@@ -16,8 +16,8 @@ module u2plus_core
    output [1:0] debug_clk,
 
    // Expansion
-   input exp_pps_in,
-   output exp_pps_out,
+   input exp_time_in,
+   output exp_time_out,
    
    // GMII
    //   GMII-CTRL
@@ -683,7 +683,8 @@ module u2plus_core
 
    time_64bit #(.TICKS_PER_SEC(32'd100000000),.BASE(SR_TIME64)) time_64bit
      (.clk(dsp_clk), .rst(dsp_rst), .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
-      .pps(pps_in), .vita_time(vita_time), .pps_int(pps_int));
+      .pps(pps_in), .vita_time(vita_time), .pps_int(pps_int),
+      .exp_time_in(exp_time_in), .exp_time_out(exp_time_out));
    
    // /////////////////////////////////////////////////////////////////////////////////////////
    // Debug Pins