uhd: replace <prefix> with <install-path> in docs for clarity

7 files changed, 17 insertions, 17 deletions

diff --git a/host/docs/build.rst b/host/docs/build.rst
index c645817ab..063b2b371 100644
--- a/host/docs/build.rst
+++ b/host/docs/build.rst
@@ -116,7 +116,7 @@ Generate Makefiles with cmake
 Additionally, configuration variables can be passed into cmake via the command line.
 The following common-use configuration variables are listed below:
 
-* For a custom install prefix: -DCMAKE_INSTALL_PREFIX=<prefix>
+* For a custom install prefix: -DCMAKE_INSTALL_PREFIX=<install-path>
 * To install libs into lib64: cmake -DLIB_SUFFIX=64
 
 Example usage:
diff --git a/host/docs/dboards.rst b/host/docs/dboards.rst
index 7f205c404..419456df2 100644
--- a/host/docs/dboards.rst
+++ b/host/docs/dboards.rst
@@ -182,7 +182,7 @@ If you lose R193, you can use anything from 0 to 10 ohms there.
 With the daughterboard plugged-in, run the following commands:
 ::
 
-    cd <prefix>/share/uhd/utils
+    cd <install-path>/share/uhd/utils
     ./usrp_burn_db_eeprom --id=0x000d --unit=RX --args=<args> --slot=<slot>
 
 * <args> are device address arguments (optional if only one USRP is on your machine)
@@ -209,7 +209,7 @@ These are all 0-ohm, so if you lose one, just short across the appropriate pads
 With the daughterboard plugged-in, run the following commands:
 ::
 
-    cd <prefix>/share/uhd/utils
+    cd <install-path>/share/uhd/utils
     ./usrp_burn_db_eeprom --id=<rx_id> --unit=RX --args=<args> --slot=<slot>
     ./usrp_burn_db_eeprom --id=<tx_id> --unit=TX --args=<args> --slot=<slot>
 
diff --git a/host/docs/general.rst b/host/docs/general.rst
index 2894fbf88..73b820c84 100644
--- a/host/docs/general.rst
+++ b/host/docs/general.rst
@@ -52,5 +52,5 @@ Support for dynamically loadable modules
 For a module to be loaded at runtime, it must be:
 
 * found in the UHD_MODULE_PATH environment variable,
-* installed into the <prefix>/share/uhd/modules directory,
+* installed into the <install-path>/share/uhd/modules directory,
 * or installed into /usr/share/uhd/modules directory (unix only).
diff --git a/host/docs/identification.rst b/host/docs/identification.rst
index 90484744c..deda61531 100644
--- a/host/docs/identification.rst
+++ b/host/docs/identification.rst
@@ -107,7 +107,7 @@ Set a custom name
 Run the following commands:
 ::
 
-    cd <prefix>/share/uhd/utils
+    cd <install-path>/share/uhd/utils
     ./usrp_burn_mb_eeprom --args=<optional device args> --key=name --val=lab1_xcvr
 
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
diff --git a/host/docs/images.rst b/host/docs/images.rst
index f5be88a65..adfa6d530 100644
--- a/host/docs/images.rst
+++ b/host/docs/images.rst
@@ -54,8 +54,8 @@ When installing images from an archive, there are two options:
 **Option 1:**
 
 Unpack the archive into the UHD installation prefix.
-The UHD will always search <prefix>/share/uhd/images for image files.
-Where <prefix> was set by the CMAKE_INSTALL_PREFIX at configure-time.
+The UHD will always search <install-path>/share/uhd/images for image files.
+Where <install-path> was set by the CMAKE_INSTALL_PREFIX at configure-time.
 
 **Option 2:**
 
diff --git a/host/docs/usrp2.rst b/host/docs/usrp2.rst
index 912f7d2bd..161170f2c 100644
--- a/host/docs/usrp2.rst
+++ b/host/docs/usrp2.rst
@@ -25,11 +25,11 @@ Use the card burner tool (unix)
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 ::
 
-    sudo <prefix>/share/uhd/utils/usrp2_card_burner_gui.py
+    sudo <install-path>/share/uhd/utils/usrp2_card_burner_gui.py
 
     -- OR --
 
-    cd <prefix>/share/uhd/utils
+    cd <install-path>/share/uhd/utils
     sudo ./usrp2_card_burner.py --dev=/dev/sd<XXX> --fpga=<path_to_fpga_image>
     sudo ./usrp2_card_burner.py --dev=/dev/sd<XXX> --fw=<path_to_firmware_image>
 
@@ -42,7 +42,7 @@ Use the card burner tool (windows)
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 ::
 
-    <path_to_python.exe> <prefix>/share/uhd/utils/usrp2_card_burner_gui.py
+    <path_to_python.exe> <install-path>/share/uhd/utils/usrp2_card_burner_gui.py
 
 
 ------------------------------------------------------------------------
@@ -58,11 +58,11 @@ Use the net burner tool (unix)
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 ::
 
-    sudo <prefix>/share/uhd/utils/usrp_n2xx_net_burner_gui.py
+    sudo <install-path>/share/uhd/utils/usrp_n2xx_net_burner_gui.py
 
     -- OR --
 
-    cd <prefix>/share/uhd/utils
+    cd <install-path>/share/uhd/utils
     ./usrp_n2xx_net_burner.py --addr=<ip address> --fw=<path for firmware image>
     ./usrp_n2xx_net_burner.py --addr=<ip address> --fpga=<path to FPGA image>
 
@@ -71,7 +71,7 @@ Use the net burner tool (Windows)
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 ::
 
-    <path_to_python.exe> <prefix>/share/uhd/utils/usrp_n2xx_net_burner_gui.py
+    <path_to_python.exe> <install-path>/share/uhd/utils/usrp_n2xx_net_burner_gui.py
 
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 Device recovery and bricking
@@ -145,7 +145,7 @@ and the network must be setup properly as described above.
 Run the following commands:
 ::
 
-    cd <prefix>/share/uhd/utils
+    cd <install-path>/share/uhd/utils
     ./usrp_burn_mb_eeprom --args=<optional device args> --key=ip-addr --val=192.168.10.3
 
 **Method 2 (Linux Only):**
@@ -154,7 +154,7 @@ It uses raw ethernet packets to bypass the IP/UDP layer to communicate with the
 Run the following commands:
 ::
 
-    cd <prefix>/share/uhd/utils
+    cd <install-path>/share/uhd/utils
     sudo ./usrp2_recovery.py --ifc=eth0 --new-ip=192.168.10.3
 
 ------------------------------------------------------------------------
@@ -343,5 +343,5 @@ Test the PPS input with the following app:
 
 ::
 
-    cd <prefix>/share/uhd/examples
+    cd <install-path>/share/uhd/examples
     ./test_pps_input --args=<args>
diff --git a/host/docs/usrp_e1xx.rst b/host/docs/usrp_e1xx.rst
index ffcd370dd..fb5848bad 100644
--- a/host/docs/usrp_e1xx.rst
+++ b/host/docs/usrp_e1xx.rst
@@ -61,5 +61,5 @@ can talk directly to the clock generator over a SPI interface.
 Run the following commands to restore the clock generator to a usable state:
 ::
 
-    cd <prefix>/share/uhd/usrp_e_utilities
+    cd <install-path>/share/uhd/usrp_e_utilities
     ./usrp-e-utility --fpga=../images/usrp_e100_pt_fpga.bin --reclk