From 0d9e44508a0ba6c9eb4b9bf6a418fbe1673203b9 Mon Sep 17 00:00:00 2001 From: "Matthias P. Braendli" Date: Fri, 10 Mar 2023 15:38:08 +0100 Subject: Update READMEs --- README.md | 173 ++------------------------------------------------------------ 1 file changed, 5 insertions(+), 168 deletions(-) (limited to 'README.md') diff --git a/README.md b/README.md index e2dc30b..067319b 100644 --- a/README.md +++ b/README.md @@ -1,170 +1,7 @@ -Picardy 2020 -============ +Picardy 2020 and DART-70 +======================== -A reinterpretation of the [Picardy 2m SSB transceiver](http://f6feo.homebuilder.free.fr/transceiver_PICARDY.html) by F6FEO -combined with the [Anglian 3L transverter](http://www.g4ddk.com/Products.html). -Additional inspirations: uBitx, the KN-Q7, LimeRFE and EI9GQ's "Building a Transceiver" book. Many thanks to all the -designers behind these projects. - -The hardware design is licenced under the "CERN Open Hardware Licence Version 2 - Permissive", see *cern_ohl_p_v2.txt*. -The firmware is MIT-licenced. - -* Designed in KiCad -* Meant to be used with a microwave transverter and stand-alone 144MHz - * For transverter usage, no PA reduces current consumption. - * For stand-alone, see MMRF1021 amplifier below. -* Using a STM32F103C8T6 controller - * Programmed in [Rust](https://rust-lang.org/) - * Si5351 clock source (generates HF clocks) - * An LCD display -* Discarded ideas - * Include a Lars Widenius GPSDO originally published on [eevblog](https://www.eevblog.com/forum/projects/lars-diy-gpsdo-with-arduino-and-1ns-resolution-tic/?all) - * Offer a 10MHz output refclk for a transverter - * Instead, have a 25MHz ref input, and use an external reference - * Use the Si5351 to generate the VHF LO at 116 MHz - * It wasn't clean enough, so a separate [XTAL LO board](./lo_board/) was designed - * With a 114.286 MHz crystal, we get a first IF of 29714 kHz - -*First QSO done with this transceiver and MMRF1021 amplifier on 2020-12-07* - -On RX, an [LNA4ALL](http://lna4all.blogspot.com/) LNA was used. On TX, 2x SPF5189Z, a bandpass filter to remove the LO, -and the [MMRF1021](http://git.mpb.li/git/mmrf1021-pa/about/) amplifier were used, giving about 200mW output power on the -very first trial. - -Later, the external bandpass and 2x SPF5189Z were replaced by an internal bandpass with less insertion loss and a single -SPF5189Z. - - -*First 3cm QSO done with Picardy 2020 as IF transceiver on 2020-02-21* - -Using a Downeast Microwave 10368CK transverter. - - -TODO -==== - -* Where does the 1.6kHz offset come from? - -Open questions -============== - -* CW - * Does the trick with the DC bias to leak the LO work ? - * Not tested, but plan B done (J306) - * Use an additional PWM output for plan B? - * Put sidetone volume setting before RV303? - * Hook up to LM386 BYPASS? - -Issues -====== - -* Coupling between VHF filter coils was way too large - * Fixed, replacement of coupling caps. -* SEQ0 is used in inverted-logic in baseband, and noninverted for power relay - * Due to inconsistent naming - * Ugly fix on K603 side, use SEQ0n, SEQ1, SEQ2 -* G6K-2F-RF all have the Y footprint, not the equidistant one. - * And they have additional GND flaps too, which are not in the Kicad footprint library - * Can be kludged-in -* 5V jumper is less useful as hoped - * Intention: disable VHF stuff - * Unintended effect: removes LCD backlight -* C319 and C326 are redundant -* BC856W wrong footprint -* R327 upsets DC offset of audio amp, added 2.2uF capacitive decoupling in series with 1k - * PTT makes loud click, assemble with 100nF only, still loud - * Connected LM386 back to 8V, through 0 Ohm instead of 10 Ohm (was on 12V through 10 Ohm because DCDC noise). Still - loud. - * Investigate other muting schemes. - * Connecting BYPASS to GND generates click - * 2N3819 based muting according to G3YCC works better. - * Assemble 1k + 100nF for coupling, revert to 12k for R329, use 20k for R326 to slow down the transition a bit -* 2m LPF from LimeRFE use values I don't stash - * 20pF done with 2x 10pF -* SW: ADC input for buttons looks messed up... - * Four buttons instead of 7 are enough anyway -* Connect 3V3 LDO to 12V directly -* Also, replace DCDC by L7808 to improve spectral purity - * Actually there would be more to be gained with a DCDC on 5V or 3V3! -* Added a LM360T LDO for the MMRF1021 so that it can be powered from 3S LiPo (11.1V) and Pb (13.8V) batteries -* Add 2.2uF caps near consumers - * Replace C535, C536 - * Replace C343, C315 - * Next to R508 - * Next to R305 - * Parallel to C331 - * Parallel to C607 - * Next to R306 - * Next to R504 - * Next to R328 - * Next to R515 -* Reduce RF coupling - * Added 100pF caps on microphone connector and CW input - * Added 22pF on DC jack, DIN - -PCB Assembly Plan -================= - -1. DCDC converter for 8V and LDOs - * Check output voltages - * Check drop under load - -2. STM32F103C8T6 - * Programming - * Sidetone low-pass - * Probably need to do a UI proto already - -3. Si5153 - * Check I2C works - -4. 8V and 5V relay - * Check switching with microcontroller and validate resistors - -5. Baseband - * Crystal filter shape - * RX and TX filter shape - * Receive path: IF mixer, crystal filter relay, IF AGC, BFO mixer, AGC measure, AF amp, SPKR - * Verify LO levels into SA602A: at least 200mVpp - * Transmit path: Mic amp - -6. Anglian - * LO filter shape - * LO amp. Mixer needs +7dBm - * All passives - * Verify correct voltages for amplifiers - * Verify PIN currents (Between 20mA and 60mA, below 0.8V) - * Verify filter shapes - * IF amplifiers, both RX and TX - * VHF amplifiers - * VHF bandpass filter - * Mixer - -7. External switching relay - - -Tuning -====== - -IF gain (R307) - -Define if we need C361, C360 - -Ensure LO1 and BFO voltage level at TP301 TP302 - - - -Additional remarks -================== - -Very good [explanations](https://groups.io/g/BITX20/topic/si5351a_facts_and_myths/5430607) about DDS vs DPLL from Hans Summers - -Si5153 test before PCB fab: - -* It seems the desired frequency plan can be achieved: - * clk0: LO1 = 28 - 4.9152 + VFO, i.e. from 23 to 25 - * clk1: VHF-LO = 144 + 28 and 144 - 28, i.e. 116 MHz - * clk2: BFO = 4.91521 - * See `freqplan.py` -* This ended up being too noisy and was replaced by an external VHF LO, with LO1 and BFO generated with Si5153 - * No 116MHz crystals on mouser, but 114.285MHz are available, HF bandpass filters recalculated. +This repository contains design files and firmware for both the Picardy 2020 2m SSB/CW transceiver +and the DART-70 4m SSB/CW transceiver designed in 2023. +Please see [README-4m](README-4m.md) or [README-Picardy2020](README-Picardy2020.md) for more details. -- cgit v1.2.3