aboutsummaryrefslogtreecommitdiffstats
path: root/doc
Commit message (Collapse)AuthorAgeFilesLines
* Fix tone LED in code and schematicsMatthias P. Braendli2019-05-102-58/+63
|
* Move PA signal on fax_1750_interconnect schematicMatthias P. Braendli2019-05-101-6/+6
|
* Move spec and some doc from trello to doc/Matthias P. Braendli2019-05-063-20/+109
|
* Minor schematic and board changesMatthias P. Braendli2019-05-032-23/+23
|
* Update fax 1750 interconnect drawingMatthias P. Braendli2019-05-031-5/+50
|
* Handle 1750 front buttonMatthias P. Braendli2019-05-031-1/+1
|
* Add some 1750 detection code to glutt-o-logicMatthias P. Braendli2019-04-113-150/+850
|
* layout: connect new outputsMatthias P. Braendli2019-03-021-251/+213
|
* Allocate SQ2, DET 1750 and NF, partly adapt code, schematics and layoutMatthias P. Braendli2019-03-023-28/+129
|
* Remap PIOs in pio.txt, schematic and layoutMatthias P. Braendli2019-03-014-5605/+6657
|
* Add new FAX and 1750 interconnect boardMatthias P. Braendli2019-03-011-0/+12226
|
* Update synoptique 2016 DB-25 connectorsMatthias P. Braendli2019-01-301-989/+657
|
* Update Synoptique, add Synoptique 2016Matthias P. Braendli2019-01-282-7/+12430
|
* Corrections SynoptiqueMatthias P. Braendli2019-01-271-946/+2250
|
* Add synoptique 2007Matthias P. Braendli2019-01-271-0/+9808
|
* Allow to open the relay with SQ using fax modeMaximilien Cuony2017-04-301-367/+476
|
* Update statemachine diagramMatthias P. Braendli2016-10-211-79/+192
|
* Update resistors on V1wire perfboardMatthias P. Braendli2016-09-211-70/+17
|
* Update ECOUTE transitions in fsm docMatthias P. Braendli2016-09-211-9/+10
|
* Update FSM description documentMatthias P. Braendli2016-09-211-299/+570
|
* Increase component sizes on schematicMatthias P. Braendli2016-09-021-2056/+2023
|
* Change minimum QSO length for LETTER to 3sMatthias P. Braendli2016-07-181-5/+5
| | | | It feels more natural, 5s is a bit longish.
* Fix ATTENTE, require additional timing checkMatthias P. Braendli2016-07-181-4/+4
|
* FSM: Remove TX_ON from OPEN1Matthias P. Braendli2016-07-181-272/+238
| | | | | | This makes it impossible to get stuck with TX_ON if SQ never goes low. Transition from BALISE_OPEN directly goes to OPEN2, regardless of SQ, making a seamless switch from beacon-mode to repeater-mode for the users.
* Update FSM documentMatthias P. Braendli2016-07-171-151/+312
| | | | | - Add QSO to ECOUTE transition - Distinguish BALISE and BALISE_OPEN
* Update schematic, make V-1wire fatMatthias P. Braendli2016-07-141-8/+9
|
* Add db25 connector schematicMatthias P. Braendli2016-07-141-0/+1188
|
* Add sticker.svgMatthias P. Braendli2016-07-131-0/+1924
|
* Invert REPLIE signal in softwareMatthias P. Braendli2016-07-101-4/+4
|
* Add REPLIE inverter and voltage shifterMatthias P. Braendli2016-07-101-47/+418
|
* Add GPS SMA connector to back plateMatthias P. Braendli2016-07-101-61/+107
|
* Fix opamp connection on schematicMatthias P. Braendli2016-06-242-193/+205
|
* Update schematics and perfboardMatthias P. Braendli2016-06-232-1176/+1531
| | | | | Add audio filter, Correct SWR measurement, Zener voltages, GPS EPPS output, Cosmetics
* Assign GPS EPPS output in docMatthias P. Braendli2016-06-204-95/+706
|
* Create backside connections documentMatthias P. Braendli2016-06-161-0/+1570
|
* Update SECOURS on schematic and perfboardMatthias P. Braendli2016-06-132-97/+193
|
* Update schematic and layoutMatthias P. Braendli2016-06-122-10/+10
|
* Fix analog supply voltage readoutMatthias P. Braendli2016-06-121-22/+153
|
* Assign pins to analog inputsMatthias P. Braendli2016-06-123-17/+132
|
* Fix GND on perfboard DB25Matthias P. Braendli2016-06-051-7/+7
|
* Fix DB25 numberingMatthias P. Braendli2016-05-302-217/+216
|
* perfboard: update opamp circuitMatthias P. Braendli2016-05-141-295/+636
|
* Schematic: Update dateMatthias P. Braendli2016-05-141-4/+4
|
* Schematic: 22k instead of 20k dividerMatthias P. Braendli2016-05-141-59/+7
|
* schematic: add opamp gain and protectionMatthias P. Braendli2016-05-131-47/+638
|
* Remove orange led from pio.txtMatthias P. Braendli2016-04-171-4/+0
|
* Fix RS232 issuesMaximilien Cuony2016-04-151-386/+395
|
* Move MAX232Matthias P. Braendli2016-04-101-100/+123
|
* Move MOD ON 2N2222Matthias P. Braendli2016-04-101-8/+9
|
* Move 1750 dividerMatthias P. Braendli2016-04-101-20/+20
|
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-14 17:39:27 +0000