Commit message (Collapse) | Author | Age | Files | Lines | |
---|---|---|---|---|---|
* | Update statemachine diagram | Matthias P. Braendli | 2016-10-21 | 1 | -79/+192 |
| | |||||
* | Update resistors on V1wire perfboard | Matthias P. Braendli | 2016-09-21 | 1 | -70/+17 |
| | |||||
* | Update ECOUTE transitions in fsm doc | Matthias P. Braendli | 2016-09-21 | 1 | -9/+10 |
| | |||||
* | Update FSM description document | Matthias P. Braendli | 2016-09-21 | 1 | -299/+570 |
| | |||||
* | Increase component sizes on schematic | Matthias P. Braendli | 2016-09-02 | 1 | -2056/+2023 |
| | |||||
* | Change minimum QSO length for LETTER to 3s | Matthias P. Braendli | 2016-07-18 | 1 | -5/+5 |
| | | | | It feels more natural, 5s is a bit longish. | ||||
* | Fix ATTENTE, require additional timing check | Matthias P. Braendli | 2016-07-18 | 1 | -4/+4 |
| | |||||
* | FSM: Remove TX_ON from OPEN1 | Matthias P. Braendli | 2016-07-18 | 1 | -272/+238 |
| | | | | | | This makes it impossible to get stuck with TX_ON if SQ never goes low. Transition from BALISE_OPEN directly goes to OPEN2, regardless of SQ, making a seamless switch from beacon-mode to repeater-mode for the users. | ||||
* | Update FSM document | Matthias P. Braendli | 2016-07-17 | 1 | -151/+312 |
| | | | | | - Add QSO to ECOUTE transition - Distinguish BALISE and BALISE_OPEN | ||||
* | Update schematic, make V-1wire fat | Matthias P. Braendli | 2016-07-14 | 1 | -8/+9 |
| | |||||
* | Add db25 connector schematic | Matthias P. Braendli | 2016-07-14 | 1 | -0/+1188 |
| | |||||
* | Add sticker.svg | Matthias P. Braendli | 2016-07-13 | 1 | -0/+1924 |
| | |||||
* | Invert REPLIE signal in software | Matthias P. Braendli | 2016-07-10 | 1 | -4/+4 |
| | |||||
* | Add REPLIE inverter and voltage shifter | Matthias P. Braendli | 2016-07-10 | 1 | -47/+418 |
| | |||||
* | Add GPS SMA connector to back plate | Matthias P. Braendli | 2016-07-10 | 1 | -61/+107 |
| | |||||
* | Fix opamp connection on schematic | Matthias P. Braendli | 2016-06-24 | 2 | -193/+205 |
| | |||||
* | Update schematics and perfboard | Matthias P. Braendli | 2016-06-23 | 2 | -1176/+1531 |
| | | | | | Add audio filter, Correct SWR measurement, Zener voltages, GPS EPPS output, Cosmetics | ||||
* | Assign GPS EPPS output in doc | Matthias P. Braendli | 2016-06-20 | 4 | -95/+706 |
| | |||||
* | Create backside connections document | Matthias P. Braendli | 2016-06-16 | 1 | -0/+1570 |
| | |||||
* | Update SECOURS on schematic and perfboard | Matthias P. Braendli | 2016-06-13 | 2 | -97/+193 |
| | |||||
* | Update schematic and layout | Matthias P. Braendli | 2016-06-12 | 2 | -10/+10 |
| | |||||
* | Fix analog supply voltage readout | Matthias P. Braendli | 2016-06-12 | 1 | -22/+153 |
| | |||||
* | Assign pins to analog inputs | Matthias P. Braendli | 2016-06-12 | 3 | -17/+132 |
| | |||||
* | Fix GND on perfboard DB25 | Matthias P. Braendli | 2016-06-05 | 1 | -7/+7 |
| | |||||
* | Fix DB25 numbering | Matthias P. Braendli | 2016-05-30 | 2 | -217/+216 |
| | |||||
* | perfboard: update opamp circuit | Matthias P. Braendli | 2016-05-14 | 1 | -295/+636 |
| | |||||
* | Schematic: Update date | Matthias P. Braendli | 2016-05-14 | 1 | -4/+4 |
| | |||||
* | Schematic: 22k instead of 20k divider | Matthias P. Braendli | 2016-05-14 | 1 | -59/+7 |
| | |||||
* | schematic: add opamp gain and protection | Matthias P. Braendli | 2016-05-13 | 1 | -47/+638 |
| | |||||
* | Remove orange led from pio.txt | Matthias P. Braendli | 2016-04-17 | 1 | -4/+0 |
| | |||||
* | Fix RS232 issues | Maximilien Cuony | 2016-04-15 | 1 | -386/+395 |
| | |||||
* | Move MAX232 | Matthias P. Braendli | 2016-04-10 | 1 | -100/+123 |
| | |||||
* | Move MOD ON 2N2222 | Matthias P. Braendli | 2016-04-10 | 1 | -8/+9 |
| | |||||
* | Move 1750 divider | Matthias P. Braendli | 2016-04-10 | 1 | -20/+20 |
| | |||||
* | Change resistor orientation next to 2N2222 | Matthias P. Braendli | 2016-04-10 | 1 | -434/+452 |
| | |||||
* | Fix TX ON connections | Matthias P. Braendli | 2016-04-10 | 1 | -18/+18 |
| | |||||
* | Move DB25 | Matthias P. Braendli | 2016-03-15 | 1 | -28/+28 |
| | |||||
* | Move big header up by two | Matthias P. Braendli | 2016-03-15 | 1 | -31/+32 |
| | |||||
* | Move MAX232 by one | Matthias P. Braendli | 2016-03-15 | 1 | -37/+39 |
| | |||||
* | Move LM324 | Matthias P. Braendli | 2016-03-15 | 1 | -49/+54 |
| | |||||
* | Fix base board size | Matthias P. Braendli | 2016-03-15 | 1 | -875/+139 |
| | |||||
* | Move some resistors | Matthias P. Braendli | 2016-03-15 | 1 | -132/+110 |
| | |||||
* | Cleanup DB25 header routing | Matthias P. Braendli | 2016-02-21 | 1 | -25/+25 |
| | |||||
* | Reorder DB25 pin header | Matthias P. Braendli | 2016-02-21 | 1 | -102/+163 |
| | |||||
* | Change all beziers to straight segments | Matthias P. Braendli | 2016-02-07 | 1 | -161/+282 |
| | |||||
* | Use power bus for opamps | Matthias P. Braendli | 2016-02-07 | 1 | -1400/+997 |
| | |||||
* | Add power bus to perfboard | Matthias P. Braendli | 2016-02-07 | 1 | -1091/+1212 |
| | |||||
* | Add LM324 to perfboard, update schematic | Matthias P. Braendli | 2016-02-04 | 2 | -242/+1360 |
| | |||||
* | Add 1wire, analog measurements | Matthias P. Braendli | 2016-02-04 | 2 | -870/+2096 |
| | |||||
* | Add DCDC to schematic and perfboard | Matthias P. Braendli | 2016-02-04 | 2 | -608/+1218 |
| |