; This is an example configuration file that illustrates ; the structure of the configuration. ; It doesn't show all possible options. A more detailed example ; is available in doc/advanced.mux ; ; It contains two services, one DAB and one DAB+, and also shows ; both the file input useful for offline processing, and the ; ZeroMQ input useful in a 24/7 scenario. ; More information about the usage of the tools is available ; in the guide, which can be found on the ; www.opendigitalradio.org website. ; ; As you can see, comments are defined by semicolons. ; ; It consists of six mandatory sections, whose relative order in this ; file are of no importance. ; The general section defines global multiplex parameters. general { ; the DAB Transmission mode (values 1-4 accepted) dabmode 1 ; the number of ETI frames to generate (set to 0 to get an unlimited number) nbframes 10 ; boolean fields can accept either false or true as values: ; Set to true to enable logging to syslog syslog false ; Enable timestamp definition necessary for SFN ; This also enables time encoding using the MNSC. tist false ; The management server is a simple TCP server that can present ; statistics data (buffers, overruns, underruns, etc) ; which can then be graphed a tool like Munin ; The doc/stats_dabmux_multi.py tool is a suitable ; plugin for that. ; If the port is zero, or the line commented, the server ; is not started. managementport 12720 } remotecontrol { ; enable the telnet remote control server on the given port ; This server allows you to read and define parameters that ; some features export. It is only accessible from localhost. ; Set the port to 0 to disable the server telnetport 12721 ; the remote control server makes use of the unique identifiers ; for the subchannels, services and components. Make sure you ; chose them so that you can identify them. } ; Some ensemble parameters ensemble { id 0x4fff ; you can also use decimal if you want ecc 0xec ; Extended Country Code local-time-offset auto ; autmatically calculate from system local time ; or ;local-time-offset 1 ; in hours, supports half-hour offsets ; all labels are maximum 16 characters in length label "OpenDigitalRadio" ; The short label is built from the label by erasing letters, and cannot ; be longer than 8 characters. If omitted, it will be truncated from the ; label shortlabel "ODR" } ; Definition of DAB services services { ; Each service has it's own unique identifier, that is ; used throughout the configuration file and for the RC. srv-fu { id 0x8daa label "Funk" ; you can define a shortlabel too. } srv-ri { id 0x8dab label "Rick" } } subchannels { sub-fu { ; This is our DAB programme, using a file input type audio inputfile "funk.mp2" bitrate 128 id 10 protection 3 } sub-ri { ; This is our DAB+ programme, using a ZeroMQ type dabplus ; Accepts connections to port 9000 from any interface. ; Use FDK-AAC-DABplus as encoder inputfile "tcp://*:9000" bitrate 96 id 1 protection 3 ; ZMQ specific options, mandatory: ; Maximum size of input buffer, in AAC frames (24ms) ; when this buffer size is reached, some frames will be ; discarded to get the size again below this value. ; As the present implementation discards entire AAC superframes, ; (5 frames = 120ms) the effect will clearly be audible. zmq-buffer 40 ; At startup or after an underrun, the buffer is filled to this ; amount of AAC frames before streaming starts. zmq-prebuffering 20 ; In an ideal scenario, where the input rate exactly corresponds ; to the rate at which the frames are consumed by dabmux, you ; see the buffer level staying around the zmq-prebuffering value. ; Network latency jitter can make it temporarily go lower or higher. ; Encoder clock drift will make the buffer either slowly fill or ; empty, which will create intermittent glitches. } } ; In our simple example, each component links one service to one subchannel components { ; the component unique identifiers are used for the RC. comp-fu { ; According to specification, you should not define component labels if ; the service is only used in one component. The service label is sufficient ; in that case. service srv-fu subchannel sub-fu } comp-ri { service srv-ri subchannel sub-ri } } ; A list of outputs outputs { ; The unique-id can be used by the remote control or the statistics server ; to identify the output ; Output RAW ETI NI to standard output stdout "fifo:///dev/stdout?type=raw" ; ZeroMQ output example ; This output does not back-pressure the multiplexer. ; Listen on all interfaces, on port 9100 ;zmq "zmq+tcp://*:9100" ; Output ETI-over-TCP. This is like piping a RAW ETI NI data stream ; into a TCP socket, except that the output can handle simultaneous ; connections. ; 0.0.0.0 means "listen on all interfaces" ; This output does not back-pressure the multiplexer. ;tcp "tcp://0.0.0.0:9200" ; Throttle output to real-time (one ETI frame every 24ms) ;throttle "simul://" ; Important! For real-time operation, you need to have exactly one ; output that applies back-pressure to ODR-DabMux, otherwise it will run ; at the highest possible rate on your system! ; ; For an output to a pipe, the data consumer at the other end of the pipe ; will dictate the multiplexing rate to ODR-DabMux. ; ; If you use the zmq+tcp:// or the tcp:// output, ; you must also enable a simul:// output! }