diff options
Diffstat (limited to 'dpd')
| -rw-r--r-- | dpd/README.md | 14 | ||||
| -rw-r--r-- | dpd/dpd.ini | 4 | ||||
| -rwxr-xr-x | dpd/main.py | 13 |
3 files changed, 18 insertions, 13 deletions
diff --git a/dpd/README.md b/dpd/README.md index fc84bad..307a2f5 100644 --- a/dpd/README.md +++ b/dpd/README.md @@ -103,14 +103,12 @@ This configuration file is different from usual defaults in several respects: * 4x oversampling: 8192000 sample rate * a very small digital gain, which will be overridden by the DPDCE * predistorter enabled - * UHD output with a rather low TX gain, which will be overridden by DPDCE - -The DPDCE uses automatic gain control for both TX and RX gain to get both a -high quantisation quality for the most frequent amplitude regions and a high -enough back-off so the peaks are also quantised correctly. This means that the -output power will stay at the same level, but the DPDCE may change TX gain to -trade it with digital gain and also change RX gain. This also implies that you -should *not modify txgain, rxgain, digital gain or coefficient settings manually!* + +The TX gain should be chosen so that you can drive your amplifier into +saturation with a digital gain of 0.1, so that there is margin for the DPD to +operate. + +You should *not modify txgain, rxgain, digital gain or coefficient settings manually!* When the DPDCE is used, it controls these settings, and there are command line options for you to define initial values. diff --git a/dpd/dpd.ini b/dpd/dpd.ini index af5c2fb..31d6140 100644 --- a/dpd/dpd.ini +++ b/dpd/dpd.ini @@ -18,7 +18,7 @@ gainmode=var rate=8192000 # keep in mind that the DPDCE will set the digital gain through the RC! -digital_gain=0.01 +digital_gain=0.001 [firfilter] enabled=1 @@ -43,7 +43,7 @@ filename=dpd.iq device= master_clock_rate=32768000 type=b200 -txgain=55 +txgain=80 channel=13C refclk_source=internal pps_source=none diff --git a/dpd/main.py b/dpd/main.py index f17d7df..2d9426b 100755 --- a/dpd/main.py +++ b/dpd/main.py @@ -57,6 +57,9 @@ parser.add_argument('-i', '--iterations', default=10, type=int, parser.add_argument('-L', '--lut', help='Use lookup table instead of polynomial predistorter', action="store_true") +parser.add_argument('--enable-txgain-agc', + help='Enable the TX gain AGC', + action="store_true") parser.add_argument('--plot', help='Enable all plots, to be more selective choose plots in GlobalConfig.py', action="store_true") @@ -113,7 +116,7 @@ else: dt = datetime.datetime.now().isoformat() logging.basicConfig(format='%(asctime)s - %(module)s - %(levelname)s - %(message)s', datefmt='%Y-%m-%d %H:%M:%S', - level=logging.DEBUG) + level=logging.INFO) logging_path = None logging.info("DPDCE starting up with options: {}".format(cli_args)) @@ -213,7 +216,11 @@ if cli_args.measure: #tx_shoulder_tuple = MS.average_shoulders(txframe_aligned) sys.exit(0) -tx_agc = TX_Agc(adapt, c) +# Disable TXGain AGC by default, so that the experiments are controlled +# better. +tx_agc = None +if cli_args.enable_txgain_agc: + tx_agc = TX_Agc(adapt, c) state = 'report' i = 0 @@ -225,7 +232,7 @@ while i < num_iter: if state == 'measure': # Get Samples and check gain txframe_aligned, tx_ts, rxframe_aligned, rx_ts, rx_median = meas.get_samples() - if tx_agc.adapt_if_necessary(txframe_aligned): + if tx_agc and tx_agc.adapt_if_necessary(txframe_aligned): continue # Extract usable data from measurement |