diff options
| -rw-r--r-- | doc/example.ini | 87 |
1 files changed, 39 insertions, 48 deletions
diff --git a/doc/example.ini b/doc/example.ini index e0a1fc8..cf56720 100644 --- a/doc/example.ini +++ b/doc/example.ini @@ -10,15 +10,15 @@ telnetport=2121 ; Enable zmq remote control. ; The zmq remote control is intended for machine-to-machine -; integration and requires that ODR-DabMod is built with zmq support. -; The zmq remote control may run in parallel with Telnet. +; integration. It may run in parallel with Telnet. ; ; Protocol: ; ODR-DabMod binds a zmq rep socket so clients must connect ; using either req or dealer socket. ; [] denotes message part as zmq multi-part message are used for delimitation. ; All message parts are utf-8 encoded strings and match the Telnet command set. -; Explicit codes are denoted with "". +; Messages to be sent as literal strings are denoted with "" below. +; ; The following commands are supported: ; REQ: ["ping"] ; REP: ["ok"] @@ -34,7 +34,7 @@ telnetport=2121 ; ; REQ: ["set"][module name][parameter][value] ; REP: ["ok"] _OR_ ["fail"][error description] -zmqctrl=0 +zmqctrl=1 zmqctrlendpoint=tcp://127.0.0.1:9400 [log] @@ -53,6 +53,17 @@ source=/dev/stdin ; When the end of file is reached, it is possible to rewind it loop=0 +; ETI-over-TCP example: +;transport=tcp +;source=localhost:9200 + +; When recieving data using ZeroMQ, the source is the URI to be used +;transport=zeromq +;source=tcp://localhost:8080 +; The option max_frames_queued defines the maximum number of ETI frames +; that can be in the input queue +;max_frames_queued=100 + ; EDI input. ; Listen for EDI data on a given UDP port ;transport=edi @@ -63,16 +74,6 @@ loop=0 ; No support yet for multicast, should work with and without PFT ; This EDI implementation does not support EDI Packet Resend -; When recieving data using ZeroMQ, the source is the URI to be used -;transport=zeromq -;source=tcp://localhost:8080 -; The option max_frames_queued defines the maximum number of ETI frames -; that can be in the input queue -;max_frames_queued=100 - -; ETI-over-TCP example: -;transport=tcp -;source=localhost:9200 [modulator] ; Mode 'fix' uses a fixed factor and is really not recommended. It is more @@ -99,7 +100,7 @@ gainmode=var ; Transmission mode ; If not defined, take the mode from ETI -;mode=2 +;mode=1 ; The digital gain is a value that is multiplied to each sample. It is used ; to tune the chain to make sure that no non-linearities appear up to the @@ -116,11 +117,11 @@ digital_gain=0.8 ; is enabled or not ! rate=2048000 -; CIC equaliser for USRP1 and USRP2 +; (DEPRECATED) CIC equaliser for USRP1 and USRP2 ; Set to 0 to disable CicEqualiser ; when set to 400000000, an additional USRP2 check is enabled. ; See DabModulator.cpp line 186 -dac_clk_rate=0 +;dac_clk_rate=0 ; The USRP1 does not have flexible clocking, you will need ;rate=3200000 @@ -149,19 +150,9 @@ enabled=1 ;filtertapsfile=simple_taps.txt [poly] -;Predistortion using memoryless polynom -enabled=1 +;Predistortion using memoryless polynom, see dpd/ folder for more info +enabled=0 polycoeffile=polyCoefs -;eg: -;echo "8 -;0.1 -;0 -;0 -;0 -;0 -;0 -;0 -;0" > polyCoefs [output] ; choose output: possible values: uhd, file, zmq, soapysdr @@ -191,7 +182,7 @@ output=uhd ;format=s8 ; The output file: -filename=/dev/stdout +filename=ofdm.iq [uhdoutput] ; The UHD output can be directly used with the Ettus USRP devices @@ -201,30 +192,30 @@ filename=/dev/stdout ; master_clock_rate = 4 * sample_rate ; or even a higher factor. ; -; Settings for a USRP B100: +; Settings for the B200: device= -; you can put additional UHD device settings here master_clock_rate=32768000 -type=b100 -txgain=2.0 -; Try first with small gain values -; Also set rate to 2048000 - -; For the B200 -; More information and measurements available on: -; http://wiki.opendigitalradio.org/index.php/USRP_B200_Measurements -; -; Settings: -;device= -;master_clock_rate=32768000 -;type=b200 -;txgain=40 +type=b200 +txgain=40 ; The B200 needs larger gains (up to 89dB) but, ; "Gain settings are application specific, but it is recommended that users ; consider using at least half of the available gain to get reasonable dynamic ; range." ; From the B200 User Manual ; http://files.ettus.com/uhd_docs/manual/html/usrp_b200.html +; +; More information and measurements available on: +; http://wiki.opendigitalradio.org/index.php/USRP_B200_Measurements + + +; Settings for a USRP B100: +;device= +; you can put additional UHD device settings here +;master_clock_rate=32768000 +;type=b100 +;txgain=2.0 +; Try first with small gain values +; Also set rate to 2048000 ; For the USRP1 @@ -233,7 +224,7 @@ txgain=2.0 ; the usrp1 can have two daughterboards, the subdevice parameter allows you ; to choose which one to use ;subdevice=A:0 -; The USRP1 doesn't support master_clock_rate, you need to enable resamping +; The USRP1 doesn't support master_clock_rate, you need to enable resampling ; You must specify either frequency or channel, but not both. @@ -275,7 +266,7 @@ max_gps_holdover_time=600 ; Enable the TCP server to communicate TX and RX feedback for ; digital predistortion. ; Set to 0 to disable -dpd_port=50055 +;dpd_port=50055 ; section defining ZeroMQ output properties [zmqoutput] |